Your browser does not support JavaScript! > سرویس مانوئل کانون

   کانال تلگرام کپی ایران

(0) محصول
سرویس مانوئل کانون
سه شنبه, 11 اسفند 1394 16:26

کانون Canon iRC5870N

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-0010    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0011    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0012    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0013    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but does not reach 140 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0014    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0015    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 170 deg c, but does not reach 200 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0020    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0021    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0022    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0023    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but doest not reach 140 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0024    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0025    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 170 deg C, but does not reach 200 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0026    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0026    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0030    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0031    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 C deg in 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0032    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0033    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but does not reach 140 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0034    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0001    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the fixing roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0002    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the outside heating roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0003    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the pressure roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-00FF    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
When the cause (Detailed code) cannot be found in the DC controller PCB input-port as DC controller PCB detects instantly an abnormal signal from the thermistor   copyir.com    After releasing the error with the procedure of COPIER>FUNCTION>CLEAR>ERR, 1   copyir.com Turn off the switch of control panel   copyir.com 2   copyir.com Turn off the switch of main power   copyir.com 3   copyir.com Turn on the switch of main power   copyir.com a   copyir.com When the machine returns, Check the interconnection between the DC controller PCB and the thermistor   copyir.com b   copyir.com When the machine does not return, Follow the instruction the error (Detailed) code shows on the control panel   copyir.com
E002-0010    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the fixing roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E002-0020    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the outside heating roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E002-0030    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the pressure roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0041    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the fixing roller drops below 150 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0042    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the outside heating roller drops below 190 dg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0043    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the pressure roller drops below 120 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0051    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the fixing roller drops below 150 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0052    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the outside heating roller drops below 190 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0053    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the pressure roller drops below 60 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0001    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0002    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0003    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the fixing sub heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0004    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0005    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0006    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater or the fixing main heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0007    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, or fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0008    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the pressure heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0009    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the contact heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000A    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater or the contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000B    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000C    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an error in the fixing main heater or the contact heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000D    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing main heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000E    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an error in the fixing sub heater, fixing main heater, or contact heater   copyir.comN>CLEAR>ERR   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000F    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, fixing main heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0010    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The fixing roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0020    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The outside heating roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0030    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The pressure roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E005-0000    There is an error in the take-up mechanism of the web   copyir.com
The web of the fixing assembly has been fully taken up   copyir.com After the web sensor has detected an off state, the count has exceeded 3000   copyir.com The web length sensor (PS20) is faulty   copyir.com The DC controller PCB is faulty   copyir.com    Reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB   copyir.com
E005-0010    There is an error in the take-up mechanism of the web   copyir.com
The drive solenoid of the fixing assembly is not connected   copyir.com    Check the drive solenoid of the fixing web for disconnection; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E006-0001    The fixing assembly has a comparison error   copyir.com
The fixing drawer has been identified as being disconnected   copyir.com    Check the connector of the drive solenoid of the fixing web; then, turn off and then on the main power   copyir.com
E008-0001    There is an error in relation to the life of the fixing assembly   copyir.com
The counter reading for the fixing roller has exceeded a specific count    When you have replaced the fixing roller, reset in service mode, and turn off and then on the main power: COPIER>COUNTER>DRBL-1>FX-UP-RL   copyir.com
E009-00FF    There is an outside heating roller shift error   copyir.com The outside heating roller shift motor (M22) is faulty   copyir.com The outside heating roller HP sensor (PS21) is faulty   copyir.com The DC controller PCB is faulty   copyir.com
The outside heating roller remains in contact with the fixing roller    Check the outside heating roller shift motor and the fixing motor; then, turn off and then on the main power   copyir.com
E012-0001    There is an error in the drum/ITB motor   copyir.com
After motor start-up, a lock state is not identified for 1 sec or more   copyir.com    Check the area around the photosensitive drum and the intermediate transfer belt; then, turn off and then on the main power   copyir.com
E013-0001    There is clogging by waste toner   copyir.com
There is a waste toner full error   copyir.com the soft counter reading is 250000 or higher   copyir.com    Check the amount of waste toner; then, turn off and then on the main power   copyir.com
E013-0002    There is clogging by waste toner   copyir.com
There is a waste toner feedscrew error   copyir.com The output of the waste toner lock detecting switch (SW14) is '1' for more than 1 sec   copyir.com    Check the developing motor; then, turn off and then on the main power   copyir.com
E014-0001    There is a fixing motor error   copyir.com
After motor start-up, a lock state is not identified for 1 sec or more   copyir.com    Check the fixing motor (fixing assembly); then, turn off and then on the main power   copyir.com
E020-xx10    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is lower than 62   copyir.com The ATR sensor is damage or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx11    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx11    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx12    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The opening/closing of the shutter is faulty   copyir.com The intermediate transfer belt is soiled   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx13    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The intermediate transfer belt is soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx81    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
When the background (intermediate transfer belt) is read during patch detection, the P_base_adj value is lower than 255   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The ITB cleaner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx90    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx91    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog) is 1008 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer pressure is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx92    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is -5   copyir.com0% or more 3 times continuously   copyir.com The patch sensor may be damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer engagement is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx93    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is +5   copyir.com0% or lower 3 times continuously   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer pressure is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The opening/closing of the shutter is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA3    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA9    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The T/D ratio identified for ATR control has exceeded the lower limit (3%) 3 times continuously   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is too low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Sig value is 100 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The stirring of toner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Ref value is 100 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the patch Sig value is 400 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer engagement is faulty    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 462 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
Fore INIT control (service mode INISET-*) at time of initial setup, the average of the patch Sig values is 200 or lower   copyir.com The patch sensor is damaged or has an open circuit   copyir.com the connector has poor contact   copyir.com The primary transfer engagement is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD4    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 800 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is too high   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD5    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDA    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 night Sig value samplings is 100 or more   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The stirring of toner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDB    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 light Ref samplings is 100 or more   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDC    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*), the average of the patch Sig values is 800 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com the primary transfer engagement if faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is too high   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxF1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The connector or the color toner supply clutch is not connected   copyir.com    Turn off and then on the main power; then, execute ITB cleaning   copyir.com
E020-xxFF    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
There is no toner inside the Bk developing assembly   copyir.com - the toner is not supplied to the developing assembly correctly   copyir.com - the hopper stirring motor is not rotating normally   copyir.com The hopper connector has poor contact   copyir.com The black toner supply motor (M25) is faulty   copyir.com The hopper stirring motor (M23) is faulty   copyir.com The black toner level sensor is faulty   copyir.com The DC controller is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E021-0001    There is an error in the rotation of the developing assembly   copyir.com
The developing rotary home position is not detected   copyir.com The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is faulty; the wiring of the DC controller is faulty; there is an excess load on the developing assembly   copyir.com    Turn off and then on the main power   copyir.com
E021-0002    There is an error in the rotation of the developing assembly   copyir.com
The length of the flag detected during rotation is longer or shorter than the designed flag   copyir.com The motor rotates out of sync because of poor torque caused by any of the following: the developing rotary HP sensor is faulty; the wiring of the DC controller PCB is faulty; there is an excessive load on the developing assembly   copyir.com    Turn off and then on the main power   copyir.com
E023-0001    The developing motor (M3) does not rotate normally   copyir.com
After motor start-up, a lock state is not detected for 1 sec or more   copyir.com    Turn off and then on the main power   copyir.com
E025-0001    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
There is an overcurrent in the hopper stirring motor (M23)   copyir.com    Turn off and then on the main power   copyir.com
E025-0002    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
There is an over-current in the black toner supply motor (M25)   copyir.com    Turn off and then on the main power   copyir.com
E025-0410    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
The connector of the black toner supply motor (M25) is identified as being disconnected   copyir.com    Turn off and then on the main power   copyir.com
E032-0001    The NE connector counter does not operate   copyir.com
There is an open circuit in the line for the count pulse signal   copyir.com    Turn off the main power, and check the cable for an open circuit; then, turn on the main power   copyir.com
E043-0001    There is an error in the 3   copyir.com5K paper deck pickup motor, causing an error signal   copyir.com
After motor start-up, a lock state is not detected for 1 sec or more   copyir.com The mechanical load such as on the feeding system is excessive   copyir.com    Turn off and then on the main power   copyir.com
E051-0001    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The horizontal registration home position is not detected within a specific period of time   copyir.com    Turn off and then on the main power   copyir.com
E051-0002    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The ON edge of the SUS plate is not detected during a search for home position   copyir.com    Turn off and then on the main power   copyir.com
E051-0003    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The logical motor position differs between before and after the detection operation   copyir.com    Turn off and then on the main power   copyir.com
E061-0001    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
When forming an image, the potential is 10 V or less during initial rotation   copyir.com    Turn off and then on the main power   copyir.com
E061-0002    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
At time of potential control, the potential is 10 V or less during initial rotation    Turn off and then on the main power   copyir.com
E061-0003    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
While the grid bias is being adjusted, a level of potential higher than the grid bias is sampled   copyir.com    Turn off and then on the main power   copyir.com
E061-0005    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
The difference in potential between dark and light areas is less than 100 V   copyir.com    Turn off and then on the main power   copyir.com
E061-0007    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
During adjustment of EPC offset, the potential that is read is outside the +/-30 V range   copyir.com    Turn off and then on the main power   copyir.com
E061-0008    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
During dark area potential adjustment, the sampling value is too low   copyir.com    Turn off and then on the main power   copyir.com
E061-0010    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
The sampling of the light area potential is faulty   copyir.com    Turn off and then on the main power   copyir.com
E070-00xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The home position of the intermediate transfer belt is not detected within a specific period of time    copyir.com The ITB HP sensor is faulty   copyir.com    Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then, turn on the main power   copyir.com
E070-01xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and the next home position is detected is longer than specified    copyir.com The presence of a tear may have caused the sensor to wrongly identify it as indicating the home position   copyir.com    Turn off the main power, and check the drive of the intermediate transfer belt; then, turn on the main power   copyir.com
E070-02xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and when the next home position is detected is shorter than specified    copyir.com The intermediate transfer belt slips on the drive roller, causing a delay in the timing at which the home position is detected   copyir.com    Turn off the main power, and check the surface of the intermediate transfer belt for a tear; then, turn on the main power   copyir.com
E070-03xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The detection of the home position of the intermediate transfer belt has failed once   copyir.com ITB home position sensor B and ITB home position sensor A must occur alternately; however, the same state has been detected continuously   copyir.com    Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then turn on the main power   copyir.com
E073-0001    With the front door closed, the transfer drawer connector or the transfer frame drawer connector is not connected   copyir.com
The result of detecting the feed unit indicates the absence of the unit   copyir.com    Turn off and then on the main power   copyir.com
E077-0001    The home position of the secondary transfer roller (engagement) is not detected   copyir.com
The HP sensor does not go on within 5 sec after the start of a HP search   copyir.com    Turn off and then on the main power   copyir.com
E078-0001    The home position of the transfer belt cleaner unit (engagement) is not detected   copyir.com
The HP sensor does not turn on within 5 sec after the start of a HP search   copyir.com    Turn off and then on the main power   copyir.com
E079-0001    The home position of the outside heating roller is not detected   copyir.com The outside heating roller home position sensor does not go off   copyir.com
The HP sensor does not turn on within 5 sec after the start of an HP search   copyir.com    Turn off and then on the main power   copyir.com
E079-0002    The home position of the outside heating roller is not detected   copyir.com The outside heating roller home position sensor does not go off   copyir.com
If there is an open circuit in the home position sensor of the outside heating roller home position sensor, the state of the sensor will be identified as being ON   copyir.com An error will be identified if the sensor fails to go off when it is at a point where it must normally go on and the outside heating roller shift motor is driven   copyir.com    Turn off and then on the main power   copyir.com
E100-0001    The BD is not detected   copyir.com
The BD signal is not detected when the polygon scanner has been driven for a specific period of time   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E100-0002    The BD is not detected   copyir.com
The BD signal is not detected white the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0001    There is a scanner motor error   copyir.com
The FG signal is not detected within a specific period of time after the polygon scanner has been driven   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0002    There is a scanner motor error   copyir.com
The FG signal is not detected while the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0003    There is a scanner motor error   copyir.com
The FG signal is not detected while the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E197-0002    There is an error in the communication with the fixing feed PCB   copyir.com
In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E197-0003    There is an error in the communication with the fixing feed PCB   copyir.com
Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E197-0004    There is an error in the communication with the fixing feed PCB   copyir.com
At the start of drum initial multiple rotation, there is no signal indicating the start of 24V in the fixing assembly in the communication between the DC controller and the fixing/feeding unit   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E202-0001    There is an HP error   copyir.com
An error is found during the forward trip of the HP search   copyir.com The scanner HP sensor is faulty   copyir.com The scanner motor is faulty   copyir.com The reader controller is faulty   copyir.com    Check the harness connector for connection; then, as necessary, replace the faulty part   copyir.com
E202-0002    There is an HP error   copyir.com
An error is found during the return trip of the HP search   copyir.com The scanner HP sensor is faulty   copyir.com The scanner motor is faulty   copyir.com The reader controller PCB is faulty   copyir.com    Check the harness connector for connection; then, as necessary, replace the faulty part   copyir.com
E225-0001    The lamp has blown   copyir.com
The level of shading is lower than specified   copyir.com    Check the harness connector for connection   copyir.com Check the scanning lamp (xenon), inverter, and reader controller PCB   copyir.com
E227-0001    There is a power supply (24V) error   copyir.com
At power-on, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0002    There is a power supply (24V) error   copyir.com
At the start of a job, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0003    There is a power supply (24V) error   copyir.com
At the end of a job, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0004    There is a power supply (24V) error   copyir.com
While a load is being driven, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E240-0000    There is a DDI-P communication error   copyir.com
There is a DDI-P communication error (error in communication between master and slave 0)   copyir.com    Turn off the main power, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E246-0001    An error has occurred in the course of writing to the counter memory   copyir.com
Normal access to the FRAM PCB is not possible   copyir.com A value is written to a specific area for a check on connection to the FRAM PCB; when read back, however, it is not the value that has been written   copyir.com    Turn off the main power, and check the connection of the counter PCB   copyir.com If the remedy fails, replace the counter PCB   copyir.com
E246-0002    An error has occurred in the course of writing to the counter memory   copyir.com
When the soft ID of FRAM is being repaired, FRAM is not in an initialized condition   copyir.com    Replace the counter PCB   copyir.com
E246-0003    An error has occurred in the course of writing to the counter memory   copyir.com
After an increase in the count, data is read into FRAM; when it is read back and compared, it is not the value that has been read into FRAM   copyir.com    Replace the counter PCB   copyir.com
E246-0004    An error has occurred in the course of writing to the counter memory   copyir.com
A second after repair (from SRAM to FRAM) brings out different SRAM and FRAM counter readings   copyir.com An attempt at repair has failed   copyir.com    Turn off the main power, and check the connector of the counter PCB   copyir.com If repair fails, replace the counter PCB   copyir.com
E247-0001    Error in counter memory or SRAM
An error exists in the SRAM and FRAM counter readings    Replace the counter PCB or SRAM
E248-0000    There is an error in the EEPROM   copyir.com
At time of start-up, a check error has occurred on the SRAM board    Turn off the main power, and check the SRAM board; then, as necessary, replace the SRAM board, and turn on the main power   copyir.com
E248-0001    There is an error in the EEPROM   copyir.com
There is a power-on error   copyir.com    Replace the reader controller PCB   copyir.com
E248-0002    There is an error in the EEPROM   copyir.com
There is a write error   copyir.com    Replace the reader controller PCB   copyir.com
E248-0003    There is an error in the EEPROM   copyir.com
There is a wire/read error   copyir.com    Replace the reader controller PCB   copyir.com
E315-000E    codex error
An error has occurred in the course of software decoding   copyir.com    
E350-0000    Fault in the soft ID PCB/function
An error exists in the add-on parity   copyir.com    Reset in service mode, and replace the soft ID PCB   copyir.com
E350-0001    Fault in the soft ID PCB/function
An error has occurred in the course of full data read operation on the soft ID PCB   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-0002    Fault in the soft ID PCB/function
The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match   copyir.com    Turn off the main power, and replace the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-0003    Fault in the soft ID PCB/function
The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-3000    Fault in the soft ID PCB/function
While an E350 error is backed up, the value of the check sum area of all data read from the soft ID PCB and the result of check sum computation do not match   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E351-0000    There is an error in the main controller PCB (sub)   copyir.com
At start-up, there is an error in the communication between main controller PCB (sub) and the main controller PCB (main)   copyir.com    Turn off the main power, and replace the main controller PCB (sub)   copyir.com If the result is not good, replace the main controller PCB (main), and turn on the main power   copyir.com
E354-0001    Serial No   copyir.com mismatch
All the values of the soft ID 8 digits of SEEPROM are 0x00 or 0xoff   copyir.com    Replace the soft ID PCB   copyir.com
E354-0002    Serial No   copyir.com mismatch
In the absence of an error, the soft ID PCB has been replaced with a new PCB and, in addition, the following conditions exist at the same time: - the soft IDs of the following pairs are not identical: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM   copyir.com - FRAM is not of the initialization pattern (i   copyir.come   copyir.com, the value of the check sum area is '1' but the result of computation of the counter area check sum is not '1')   copyir.com - the soft IDs of the following are all identical: SRAM1, SRAM2, SRAM   copyir.com    A mistake is likely to have been made in the course of counter PCB replacement; as a result, E355 is likely to have occurred thereafter, not permitting recovery despite an attempt to reset E355   copyir.com
E355-0001    Serial No   copyir.com mismatch PCB   copyir.com
The soft IDs of the following pairs are not identical and, in addition, any of the following conditions exist: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM   copyir.com - FRAM is of the initialization pattern (i   copyir.come   copyir.com, the value of the check sum area is '1', and the result of check sum computation of the counter area is '1')   copyir.com - the soft ID of any of the following is not identical: SRAM1, SRAM2, FRAM   copyir.com    Reset E355 (if the error occurs in the middle of repair operation)   copyir.com At times, E355 cannot be reset (intentionally designed in such a way to prevent illegal replacement in the field)   copyir.com
E400-0001    There is a DF communication error   copyir.com
There is a check sum error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E400-0002    There is a DF communication error   copyir.com
There is a reception status error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E400-0003    There is a DF communication error   copyir.com
There is a reception interrupt error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E413-0001    There is an error in the DF shift motor   copyir.com
The shift HP sensor is open   copyir.com    Check the harness; then, as necessary, replace the sensor and motor   copyir.com Check the attaching of the parts around the cam   copyir.com
E413-0002    There is an error in the DF shift motor   copyir.com
The shift HP sensor is closed   copyir.com    Check the harness; then, as necessary, replace the sensor and motor   copyir.com Check the attaching of the parts around the cam   copyir.com
E490-0001    The DF is of the wrong model   copyir.com
The installed DF is not of the correct type   copyir.com    Replace the DF with one of an appropriate type   copyir.com
E500-0001    There is a finisher communication error   copyir.com
There is an error in data communication   copyir.com An error has been detected in terms of the number of errors or the duration of the error in the communication between copier and finisher   copyir.com    Turn off the main power, and check the DC controller, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power   copyir.com
E503-0002    There is an error in the communication within the finisher (finisher R1/R2)   copyir.com
There is a data communication error   copyir.com finisher-to-saddle unit communication error    Check the connection between the saddle stitcher controller PCB and the finisher controller PCB   copyir.com
E503-0003    There is an error in the communication within the finisher (finisher R1/R2)   copyir.com
finisher-to-punch unit communication error    Check the connection between the Punch controller PCB and the finisher controller PCB   copyir.com
E505-0001    There is an error in the backup memory of the finisher (finer R1/R2)   copyir.com
There is an error in the data stored in the backup memory    Turn off the main power, and check the DC control, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power   copyir.com
E505-0002    There is an error in the backup memory of the finisher (finer R1/R2)   copyir.com
There is a data error in the punch assembly EEPROM   copyir.com    Turn off the main power, and check the wiring of the DC controller PCB and the puncher controller PCB: then, check the 24V system fuse, and turn back on the main power   copyir.com
E514-8001    There is an error in the trailing edge assist motor (finisher R1/R2)   copyir.com
The home position sensor does not go off when the trailing edge assist motor has been rotated for a specific period of time   copyir.com    1) Check the trailing edge assist home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor   copyir.com Is the wiring normal? 3) Check the trailing edge assist mechanism   copyir.com Is there a fault? 4) Try replacing the trailing edge assist motor   copyir.com Is the problem corrected?
E514-8002    There is an error in the trailing edge assist motor (finisher R1/R2)   copyir.com
The home position sensor does not go on when the trailing edge assist motor has been rotated for a specific period of time   copyir.com    1) Check the trailing edge assist home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor   copyir.com Is the wiring normal? 3) Check the trailing edge assist mechanism   copyir.com Is there a fault? 4) Try replacing the trailing edge assist motor   copyir.com Is the problem corrected?
E519-0002    There is an error in the gear change motor (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate   copyir.com    1) Check the gear change home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor   copyir.com Is the wiring normal? 3) Check the gear change mechanism   copyir.com Is there a fault? 4) Try replacing the gear change motor   copyir.com Is the problem corrected?
E519-8001    There is an error in the gear change motor (finisher R1/R2)   copyir.com
The home position sensor does not go off within a specific period of time after the gear change motor has started to rotate   copyir.com    1) Check the gear change home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor   copyir.com Is the wiring normal? 3) Check the gear change mechanism   copyir.com Is there a fault? 4) Try replacing the gear change motor   copyir.com Is the problem corrected?
E530-8001    There is an error in front alignment (finisher R1/R2)   copyir.com
Th alignment motor has started to rotate   copyir.come home position sensor does not go off within a specific period of time after the front    1) Check the pre-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor   copyir.com Is the problem corrected?
E530-8002    There is an error in front alignment (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate   copyir.com    1) Check the pre-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor   copyir.com Is the problem corrected?
E531-0001    There is an error in stapling (finisher R1/R2)   copyir.com
The home position sensor does not go off within a specific period of time after the stapler motor has started to rotate   copyir.com    1) Check the wiring between the finisher controller PCB and the stapler   copyir.com Is the wiring normal? 2) Try replacing the stapler   copyir.com Is the problem corrected?
E531-0002    There is an error in stapling (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the stapler motor has started to rotate    1) Check the wiring between the finisher controller PCB and the stapler   copyir.com Is the wiring normal? 2) Try replacing the stapler   copyir.com Is the problem corrected?
E532-8001    There is an error in the shift mechanism of the stapler   copyir.com (finisher R1/R2)
The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate   copyir.com    1) Check the stapler shift home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor   copyir.com Is the wiring normal? 3) Check the path of the stapler shift base   copyir.com Is there a mechanical obstacle? 4) Try replacing the stapler shift motor   copyir.com Is the problem corrected?
E532-8002    There is an error in the shift mechanism of the stapler   copyir.com (finisher R1/R2)
The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate   copyir.com    1) Check the stapler shift home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor   copyir.com Is the wiring normal? 3) Check the path of the stapler shift base   copyir.com Is there a mechanical obstacle? 4) Try replacing the stapler shift motor   copyir.com Is the problem corrected?
E535-0003    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
There is an error in relation to an hazardous area   copyir.com   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E535-8001    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E535-8002    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E537-8001    rear alignment error (Finisher-R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the post-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor   copyir.com Is the problem corrected?
E537-8002    rear alignment error (Finisher-R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the post-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor   copyir.com Is the problem corrected?
E540-8001    upper tray ascent/descent error (Finisher-R1/R2)
upper tray ascent/descent motor clock error    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E540-8002    upper tray ascent/descent error (Finisher-R1/R2)
area error    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E540-8003    upper tray ascent/descent error (Finisher-R1/R2)
safety switch activation    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E542-0003    lower tray ascent/descent error (Finisher-R1/R2)
safety switch activation    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E542-8001    lower tray ascent/descent error (Finisher-R1/R2)
lower tray ascent/descent motor clock error    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E542-8002    lower tray ascent/descent error (Finisher-R1/R2)
area error    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E584-0002    shutter unit error (Finisher-R1/R2)
The shutter open/closed sensor does not go on (i   copyir.come   copyir.com, the shutter does not open)   copyir.com    1) Check the shutter home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch   copyir.com Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch   copyir.com Is the problem corrected?
E584-8001    shutter unit error (Finisher-R1/R2)
The shutter open sensor does not go off (i   copyir.come   copyir.com, the shutter is not closed)   copyir.com    1) Check the shutter home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch   copyir.com Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch   copyir.com Is the problem corrected?
E590-8001    There is an error in the punch motor   copyir.com (punch unit)
The punching home position sensor is not detected when the punch motor has been driven for 200 msec   copyir.com    Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power   copyir.com
E590-8002    There is an error in the punch motor   copyir.com (punch unit)
The puncher does not detect the punching home position after the motor has stopped (initial operation)   copyir.com    Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power   copyir.com
E591-8001    There is an error in the punch dust sensor   copyir.com (punch unit)
There is an error in the light   copyir.com    Turn off and then on the main power   copyir.com
E591-8002    There is an error in the punch dust sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com    Turn off and then on the main power   copyir.com
E592-8001    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage at time of light emission   copyir.com (trailing edge sensor)    Turn off and then on the main power   copyir.com
E592-8002    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (trailing edge sensor)    Turn off and then on the main power   copyir.com
E592-8003    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 1)    Turn off and then on the main power   copyir.com
E592-8004    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 1)    Turn off and then on the main power   copyir.com
E592-8005    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 2)    Turn off and then on the main power   copyir.com
E592-8006    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 2)    Turn off and then on the main power   copyir.com
E592-8007    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage it the presence of emission of light   copyir.com (horizontal registration sensor 3)    Turn off and then on the main power   copyir.com
E592-8008    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 3)    Turn off and then on the main power   copyir.com
E592-8009    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 4)    Turn off and then on the main power   copyir.com
E592-800A    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 4)    Turn off and then on the main power   copyir.com
E593-8001    There is an error in the punch shift motor   copyir.com (punch unit)
The light-receiving voltage HP sensor does not go off at time of light emission   copyir.com    Turn off and then on the main power   copyir.com
E593-8002    There is an error in the punch shift motor   copyir.com (punch unit)
The light-receiving voltage HP sensor doest not go on without emission of light   copyir.com    Turn off and then on the main power   copyir.com
E5F0-0001    There is an error in saddle paper positioning   copyir.com
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1   copyir.com33 sec   copyir.com The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty   copyir.com    Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S)   copyir.com
E5F0-0002    There is an error in saddle paper positioning   copyir.com
The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec   copyir.com The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty   copyir.com    Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S)   copyir.com
E5F1-0001    There is an error in saddle paper folding   copyir.com
The number of detection pulses of the paper folding motor clock sensor is lower than specified   copyir.com The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty   copyir.com    Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S)   copyir.com
E5F1-0002    There is an error in saddle paper folding   copyir.com
The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec   copyir.com The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty   copyir.com    Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S)   copyir.com
E5F2-0001    There is an error in the saddle guide   copyir.com
The guide home position sensor does not turn on when the guide motor has been driven for 0   copyir.com45 sec   copyir.com The guide motor (M3S) or the guide home position sensor (PI3S) is faulty   copyir.com    Check the guide motor (M3S) /guide home position sensor (PI13S)   copyir.com
E5F2-0002    There is an error in the saddle guide   copyir.com
The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec   copyir.com The guide motor (M3S) or the guide home position sensor (PI3S) is faulty   copyir.com    Check the guide motor (M3S) /guide home position sensor (PI13S)   copyir.com
E5F3-0001    There is an error in saddle alignment   copyir.com
The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05   copyir.com sec (during initialization, 1   copyir.com67 sec)   copyir.com The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty   copyir.com    Check the alignment motor (M5S) /aligning plate home position sensor (PI5S)   copyir.com
E5F3-0002    There is an error in saddle alignment   copyir.com
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec   copyir.com The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty   copyir.com    Check the alignment motor (M5S) /aligning plate home position sensor (PI5S)   copyir.com
E5F4-0001    There is an error in saddle rear sampling   copyir.com
The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0   copyir.com5 sec or more   copyir.com The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty   copyir.com    Check he stitching motor (rear; M6S) /stitching home position sensor (rear; M
E5F4-0002    There is an error in saddle rear sampling   copyir.com
The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0   copyir.com5 sec or more   copyir.com The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty   copyir.com    Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S)   copyir.com
E5F5-0001    There is an error in saddle front stapling   copyir.com
The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0   copyir.com5 sec or more   copyir.com The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty   copyir.com    Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S)   copyir.com
E5F5-0002    There is an error in saddle front stapling   copyir.com
The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0   copyir.com5   copyir.com The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty   copyir.com    Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S)   copyir.com
E5F6-8001    There is an error in saddle butting   copyir.com
The paper pushing plate home position sensor does not turn on when the paper pushing motor has been driven for 0   copyir.com3 sec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty   copyir.com
E5F6-8002    There is an error in saddle butting   copyir.com
The paper pushing plate home position sensor does not turn off when paper pushing plate motor has been driven for 80 msec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty   copyir.com
E5F6-8003    There is an error in saddle butting   copyir.com
The number of detection pulses of the paper pushing plate motor clock sensor drops below a specific number   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty   copyir.com
E5F6-8004    There is an error in saddle butting   copyir.com
The paper pushing plate sensor does not turn off when the paper pushing plate motor has been driven for 80 msec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty   copyir.com
E5F6-8005    There is an error in saddle butting   copyir.com
The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0   copyir.com3 sec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty   copyir.com
E5F8-0001    There is an error in the saddle connector   copyir.com
The connector of the guide home position sensor is identified as being disconnected   copyir.com The connector of the guide home position sensor (PI3S) is faulty   copyir.com    Check the connectors of the guide home position sensor (PI13S)   copyir.com Check the connectors of the paper pushing plate home position sensor (PI4S)   copyir.com
E5F8-0002    There is an error in the saddle connector   copyir.com
The connector of the paper pushing plate home position sensor is identified as being disconnected   copyir.com The connector of the paper pushing plate home position sensor (PI14S) is faulty   copyir.com    Check the connectors of the paper pushing plate leading edge position sensor (PI5S)   copyir.com
E5F8-0003    There is an error in the saddle connector   copyir.com
The connector of the paper pushing plate leading edge position sensor is identified as being disconnected   copyir.com The connector of the paper pushing plate leading edge sensor (PI15S) is faulty   copyir.com    Check the connectors of the paper pushing plate leading edge position sensor (PI5S)   copyir.com
E5F9-0001    There is an error in the saddle switch   copyir.com
With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open   copyir.com The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty   copyir.com    Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S)   copyir.com
E5F9-0002    There is an error in the saddle switch   copyir.com
With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty   copyir.com    Check the front cover switch (MS2S)/delivery cover switch (MS3S)   copyir.com
E5F9-0003    There is an error in the saddle switch   copyir.com
With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S)    Check the delivery cover switch (MS3S)   copyir.com
E602    There is a hard disk error   copyir.com    
E604-0000    There is a shortage of image memory (SDRAM)   copyir.com
The amount of memory required by the model in question is not recognized   copyir.com    Set it to the size of memory suited to the model in question   copyir.com
E609-0008    Samsung HDD-related error code
The HDD does not increase to a specific temperature level within a specific time when the power is turned on   copyir.com    Replace the HDD   copyir.com
E609-0009    Samsung HDD-related error code
The HDD does not increase to a specific temperature level in relation to a sleep state   copyir.com    Turn off and then on the power   copyir.com If the return operation fails, replace the HDD   copyir.com
E610    HDD encryption key fault    
E674-0001    There is an error in the fax board   copyir.com
The fax board is detected, but communication is not possible   copyir.com    Turn off the main power, and check the fax board and the main controller PCB; then, turn on the main power   copyir.com If the machine fails to reset, replaced the fax board or the main controller PCB
E677-0003    There is an external controller error   copyir.com
An error has been detected by a check on the configuration when the external controller is being started up   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to start up, re-install the system software of the external contro
E677-0010    There is an external controller error   copyir.com
A controller for a non-Canon machine is connected   copyir.com    Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power   copyir.com If the machine fails to reset, re-install the system software of the external controller   copyir.com
E677-0080    There is an external controller error   copyir.com
There is an error in the communication with the printer after the external controller has started up normally   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to start up, re-install the system software of the external controller   copyir.com
E710-0001    There is an error in IPC initialization   copyir.com
The machine fails to become ready within 3 sec after the IPC chip has started up   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.comted up   copyir.com
E711-0002    There is an IPC communication error   copyir.com
An error has been detected 4 times or more within 1   copyir.com5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller   copyir.com
E713-0001    There is a finisher communication error   copyir.com
There is an error in the IC used for communication by the sorter   copyir.com    Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch   copyir.com If the machine does not reset, replace the DC controller PCB/finisher controller PCB   copyir.com
E717-0001    There is an error in the communication with the NE controller   copyir.com
The NE controller that was connected before the power is turned off is not recognized after the power is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E717-0002    There is an error in the communication with the NE controller   copyir.com
An IPC open circuit or an IPC communication error is not reset   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0001    error in communication with coin vendor/card reader
The coin vendor that is connected before the power is turned off is not recognized when the paper is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0002    error in communication with coin vendor/card reader
- The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered   copyir.com - There is an open circuit in the pickup delivery signal line   copyir.com - An improper connection is detected (short circuit between Tx and Rx of IPC)   copyir.com    Check the cable; thereafter, reset by making the following selections: COPIER>FUNCTION>CLEAR>ERROR
E719-0011    error in communication with coin vendor/card reader
The card reader that is connected before the power is turned off is not recognized when the paper is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0012    error in communication with coin vendor/card reader
There is an IPC cable open circuit or an IPC communication error in relation to the card reader that cannot be reset   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E730    There is a PDL error   copyir.com    
E731    There is a UFR board error   copyir.com    Turn off the main power, and check the connection of the UFR board; then, turn on the main power   copyir.com If the machine does not reset, replace the UFR board or the main controller PCB   copyir.com
E732-0001    There is an error in reader communication   copyir.com
There is an error in reader communication   copyir.com    Turn off the main power, and check the connectors to the reader, and check the power supply of the reader; then, turn on the main power   copyir.com
E732-9999    There is an error in reader communication   copyir.com
Although a printer model, the machine is identified as a reader unit at start-up   copyir.com (A copier model is started up as a printer model when the RAM is initialized   copyir.com)    Turn off and then on the main power   copyir.com
E733-0000    There is a printer communication error   copyir.com
There is a printer communication error   copyir.com At start-up, the printer is not detected   copyir.com    Turn off the main power, and check the connectors to the DC controller PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power   copyir.com
E733-0001    There is a printer communication error   copyir.com
There is a DDI-P communication error   copyir.com    Turn off the main power, and check the connectors to the DC control PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power   copyir.com
E740-0002    There is an Ethernet board error   copyir.com
At time of start-up, the MAC address is found to be illegal   copyir.com A non-Canon MAC address is detected   copyir.com    Turn off the main power, and replace the NIC; then, turn on the main power
E743-0000    There is a DDI communication error   copyir.com
There is an SCI error   copyir.com The reception data is faulty   copyir.com A reception time-out condition has occurred   copyir.com An SEQ timeout error has occurred   copyir.com An SEQ time-out error has occurred   copyir.com    Disconnect and connect the DDI-S cable connector; then, as necessary, replace the reader controller PCB or the main controller PCB   copyir.com
E744    There is a language file/boot ROM error   copyir.com    Download the appropriate language fields of the correct version using the Service Support Tool
E745    There is a TokenRing error   copyir.com    
E746-0003    The accessories board is of the wrong type   copyir.com
At time of start-up, the UFR board is found to be of the wrong type   copyir.com (A query is made to find out if the type is correct with reference to the engine ID   copyir.com)    Replace it with a UFR board of the correct type   copyir.com
E746-0004    The accessories board is of the wrong type   copyir.com
At time of start-up, the scanner board is found to be of the wrong type   copyir.com (A query is made to find out if the type is correct with reference to the engine ID   copyir.com)    Replace it with a scanner board of the correct type   copyir.com
E747    There is an error in the ASIC for image processing or in the ASIC for memory control/communication control   copyir.com
There is an error in IC1015 (ASIC for image processing) or in IC1012 (for memory control/communication control) on the main controller PCB   copyir.com (e   copyir.comg   copyir.com, image data transfer error)    Turn off the main power, and check the main controller PCB; then, turn on the main controller PCB
748    CL2 board-dependent board error    1   copyir.com Disconnect and then connect 4 to 5 G-chip boards several times   copyir.com 2   copyir.com Replace the G-chip board   copyir.com 3   copyir.com Replace the main controller PCB   copyir.com
E749-0001    Reboot instruction initiated by change in PDL configuration
A change has occurred that calls for turning off and then on the power   copyir.com    Turn off and then on the power   copyir.com
E800-0001    The interlock 24V mechanism of the fixing unit is identified as being off   copyir.com With the door closed, the interlock 24V mechanism remains off for 500 msec   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB, check the fixing unit interlock, and check the 24V system fuse; then, turn on the interlock main switch   copyir.com
E804-0004    There is any of the various types of fan errors   copyir.com
There is an error in the controller cooling fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E804-0007    There is any of the various types of fan errors   copyir.com
There is an error in the power supply cooling fan   copyir.com    Turn off the main switch, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E805-0003    The fixing heat exhaust fan is identified as having stopped or having an error   copyir.com
There is an error in the fixing heat exhaust fan   copyir.com    Turn off the main power, and check the supply of power to the fan; then, as necessary, replace the fan, and turn on the main power   copyir.com
E820-0002    There is an error in the process unit cooling fan   copyir.com
There is an error in the process unit fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E824-0000    There is an error in the primary charging suction/primary charging exhaust fan   copyir.com
There is an error in the primary charging suction mechanism   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E824-0001    There is an error in the primary charging suction/primary charging exhaust fan   copyir.com
There is an error in the primary exhaust fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and 2V system fuse; then, turn on the main switch   copyir.com

سه شنبه, 11 اسفند 1394 16:26

کانون Canon iRC5870N

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-0010    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0011    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0012    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0013    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but does not reach 140 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0014    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0015    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 170 deg c, but does not reach 200 deg C within 300 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0020    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0021    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0022    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0023    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but doest not reach 140 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0024    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 180 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0025    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 170 deg C, but does not reach 200 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0026    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0026    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec   copyir.com If the outside heating roller is in contact, within 400 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0030    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
After power-on, the temperature does not reach 50 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0031    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 50 deg C, but does not reach 80 C deg in 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0032    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 80 deg C, but does not reach 110 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0033    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 110 deg C, but does not reach 140 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E000-0034    At power-on, the rise in the temperature of the fixing assembly is not high enough   copyir.com The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact   copyir.com The AC drive PCB or the DC controller PCB is faulty   copyir.com
The temperature reaches 140 deg C, but does not reach 170 deg C within 420 sec   copyir.com    Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0001    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the fixing roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0002    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the outside heating roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-0003    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
The rise in the temperature of the pressure roller is excessive   copyir.com    Check the main thermistor, sub thermistor, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E001-00FF    The rise in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB is faulty   copyir.com
When the cause (Detailed code) cannot be found in the DC controller PCB input-port as DC controller PCB detects instantly an abnormal signal from the thermistor   copyir.com    After releasing the error with the procedure of COPIER>FUNCTION>CLEAR>ERR, 1   copyir.com Turn off the switch of control panel   copyir.com 2   copyir.com Turn off the switch of main power   copyir.com 3   copyir.com Turn on the switch of main power   copyir.com a   copyir.com When the machine returns, Check the interconnection between the DC controller PCB and the thermistor   copyir.com b   copyir.com When the machine does not return, Follow the instruction the error (Detailed) code shows on the control panel   copyir.com
E002-0010    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the fixing roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E002-0020    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the outside heating roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E002-0030    The rise in the temperature of the fixing assembly is not enough   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The temperature of the pressure roller reaches 80 deg C, but drops below 50 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0041    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the fixing roller drops below 150 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0042    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the outside heating roller drops below 190 dg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0043    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During standby, the temperature of the pressure roller drops below 120 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0051    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the fixing roller drops below 150 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0052    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the outside heating roller drops below 190 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E003-0053    After standby, the drop in the temperature of the fixing assembly is excessive   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
During copying, the temperature of the pressure roller drops below 60 deg C   copyir.com    Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0001    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0002    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0003    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the fixing sub heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0004    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0005    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0006    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater or the fixing main heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0007    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, or fixing main heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0008    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the pressure heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0009    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater or the contact heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000A    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the fixing sub heater or the contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000B    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000C    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an error in the fixing main heater or the contact heater    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000D    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing main heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000E    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an error in the fixing sub heater, fixing main heater, or contact heater   copyir.comN>CLEAR>ERR   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-000F    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
There is an SSR error in the outside heating roller heater, fixing sub heater, fixing main heater, or contact heater   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0010    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The fixing roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0020    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The outside heating roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E004-0030    There is an error in the fixing assembly protection circuit   copyir.com There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6)   copyir.com The AC driver PCB or the DC controller PCB has a fault   copyir.com
The pressure roller thermistor has an open circuit   copyir.com    Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E005-0000    There is an error in the take-up mechanism of the web   copyir.com
The web of the fixing assembly has been fully taken up   copyir.com After the web sensor has detected an off state, the count has exceeded 3000   copyir.com The web length sensor (PS20) is faulty   copyir.com The DC controller PCB is faulty   copyir.com    Reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB   copyir.com
E005-0010    There is an error in the take-up mechanism of the web   copyir.com
The drive solenoid of the fixing assembly is not connected   copyir.com    Check the drive solenoid of the fixing web for disconnection; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E006-0001    The fixing assembly has a comparison error   copyir.com
The fixing drawer has been identified as being disconnected   copyir.com    Check the connector of the drive solenoid of the fixing web; then, turn off and then on the main power   copyir.com
E008-0001    There is an error in relation to the life of the fixing assembly   copyir.com
The counter reading for the fixing roller has exceeded a specific count    When you have replaced the fixing roller, reset in service mode, and turn off and then on the main power: COPIER>COUNTER>DRBL-1>FX-UP-RL   copyir.com
E009-00FF    There is an outside heating roller shift error   copyir.com The outside heating roller shift motor (M22) is faulty   copyir.com The outside heating roller HP sensor (PS21) is faulty   copyir.com The DC controller PCB is faulty   copyir.com
The outside heating roller remains in contact with the fixing roller    Check the outside heating roller shift motor and the fixing motor; then, turn off and then on the main power   copyir.com
E012-0001    There is an error in the drum/ITB motor   copyir.com
After motor start-up, a lock state is not identified for 1 sec or more   copyir.com    Check the area around the photosensitive drum and the intermediate transfer belt; then, turn off and then on the main power   copyir.com
E013-0001    There is clogging by waste toner   copyir.com
There is a waste toner full error   copyir.com the soft counter reading is 250000 or higher   copyir.com    Check the amount of waste toner; then, turn off and then on the main power   copyir.com
E013-0002    There is clogging by waste toner   copyir.com
There is a waste toner feedscrew error   copyir.com The output of the waste toner lock detecting switch (SW14) is '1' for more than 1 sec   copyir.com    Check the developing motor; then, turn off and then on the main power   copyir.com
E014-0001    There is a fixing motor error   copyir.com
After motor start-up, a lock state is not identified for 1 sec or more   copyir.com    Check the fixing motor (fixing assembly); then, turn off and then on the main power   copyir.com
E020-xx10    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is lower than 62   copyir.com The ATR sensor is damage or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx11    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx11    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector may have poor contact   copyir.com The intermediate transfer belt may be soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx12    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Sig value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The opening/closing of the shutter is faulty   copyir.com The intermediate transfer belt is soiled   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx13    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The intermediate transfer belt is soiled    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx81    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
When the background (intermediate transfer belt) is read during patch detection, the P_base_adj value is lower than 255   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The ITB cleaner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx90    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx91    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The result (Sig D) of computation based on the reading of the patch during patch detection (analog) is 1008 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer pressure is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx92    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is -5   copyir.com0% or more 3 times continuously   copyir.com The patch sensor may be damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer engagement is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xx93    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is +5   copyir.com0% or lower 3 times continuously   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer pressure is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is lower than 62   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Sig value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The opening/closing of the shutter is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA3    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For ATR control, the Ref value is 960 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxA9    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The T/D ratio identified for ATR control has exceeded the lower limit (3%) 3 times continuously   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is too low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Sig value is 100 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The stirring of toner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the light Ref value is 100 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxC2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The variation among the 8 samplings of the patch Sig value is 400 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The primary transfer engagement is faulty    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD0    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 200 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is low   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 462 or lower   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD2    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
Fore INIT control (service mode INISET-*) at time of initial setup, the average of the patch Sig values is 200 or lower   copyir.com The patch sensor is damaged or has an open circuit   copyir.com the connector has poor contact   copyir.com The primary transfer engagement is faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD4    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 800 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The amount of supply is too high   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxD5    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDA    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 night Sig value samplings is 100 or more   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com The stirring of toner is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDB    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 light Ref samplings is 100 or more   copyir.com The ATR sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxDC    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
For INIT control (service mode INISET-*), the average of the patch Sig values is 800 or higher   copyir.com The patch sensor is damaged or has an open circuit   copyir.com The connector has poor contact   copyir.com the primary transfer engagement if faulty   copyir.com The mounting of the developing assembly is faulty   copyir.com The amount of supply is too high   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E020-xxF1    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
The connector or the color toner supply clutch is not connected   copyir.com    Turn off and then on the main power; then, execute ITB cleaning   copyir.com
E020-xxFF    There is an ATR error   copyir.com xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction
There is no toner inside the Bk developing assembly   copyir.com - the toner is not supplied to the developing assembly correctly   copyir.com - the hopper stirring motor is not rotating normally   copyir.com The hopper connector has poor contact   copyir.com The black toner supply motor (M25) is faulty   copyir.com The hopper stirring motor (M23) is faulty   copyir.com The black toner level sensor is faulty   copyir.com The DC controller is faulty   copyir.com    Turn off and then on the main power; then, execute the intermediate transfer belt   copyir.com
E021-0001    There is an error in the rotation of the developing assembly   copyir.com
The developing rotary home position is not detected   copyir.com The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is faulty; the wiring of the DC controller is faulty; there is an excess load on the developing assembly   copyir.com    Turn off and then on the main power   copyir.com
E021-0002    There is an error in the rotation of the developing assembly   copyir.com
The length of the flag detected during rotation is longer or shorter than the designed flag   copyir.com The motor rotates out of sync because of poor torque caused by any of the following: the developing rotary HP sensor is faulty; the wiring of the DC controller PCB is faulty; there is an excessive load on the developing assembly   copyir.com    Turn off and then on the main power   copyir.com
E023-0001    The developing motor (M3) does not rotate normally   copyir.com
After motor start-up, a lock state is not detected for 1 sec or more   copyir.com    Turn off and then on the main power   copyir.com
E025-0001    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
There is an overcurrent in the hopper stirring motor (M23)   copyir.com    Turn off and then on the main power   copyir.com
E025-0002    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
There is an over-current in the black toner supply motor (M25)   copyir.com    Turn off and then on the main power   copyir.com
E025-0410    There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25)   copyir.com
The connector of the black toner supply motor (M25) is identified as being disconnected   copyir.com    Turn off and then on the main power   copyir.com
E032-0001    The NE connector counter does not operate   copyir.com
There is an open circuit in the line for the count pulse signal   copyir.com    Turn off the main power, and check the cable for an open circuit; then, turn on the main power   copyir.com
E043-0001    There is an error in the 3   copyir.com5K paper deck pickup motor, causing an error signal   copyir.com
After motor start-up, a lock state is not detected for 1 sec or more   copyir.com The mechanical load such as on the feeding system is excessive   copyir.com    Turn off and then on the main power   copyir.com
E051-0001    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The horizontal registration home position is not detected within a specific period of time   copyir.com    Turn off and then on the main power   copyir.com
E051-0002    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The ON edge of the SUS plate is not detected during a search for home position   copyir.com    Turn off and then on the main power   copyir.com
E051-0003    The horizontal registration home position is not detected within a specific period of time   copyir.com The horizontal registration position is faulty (0003)   copyir.com
The logical motor position differs between before and after the detection operation   copyir.com    Turn off and then on the main power   copyir.com
E061-0001    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
When forming an image, the potential is 10 V or less during initial rotation   copyir.com    Turn off and then on the main power   copyir.com
E061-0002    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
At time of potential control, the potential is 10 V or less during initial rotation    Turn off and then on the main power   copyir.com
E061-0003    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
While the grid bias is being adjusted, a level of potential higher than the grid bias is sampled   copyir.com    Turn off and then on the main power   copyir.com
E061-0005    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
The difference in potential between dark and light areas is less than 100 V   copyir.com    Turn off and then on the main power   copyir.com
E061-0007    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
During adjustment of EPC offset, the potential that is read is outside the +/-30 V range   copyir.com    Turn off and then on the main power   copyir.com
E061-0008    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
During dark area potential adjustment, the sampling value is too low   copyir.com    Turn off and then on the main power   copyir.com
E061-0010    At time of potential control, a specific level of potential is absent   copyir.com Or, the limiter goes on   copyir.com
The sampling of the light area potential is faulty   copyir.com    Turn off and then on the main power   copyir.com
E070-00xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The home position of the intermediate transfer belt is not detected within a specific period of time    copyir.com The ITB HP sensor is faulty   copyir.com    Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then, turn on the main power   copyir.com
E070-01xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and the next home position is detected is longer than specified    copyir.com The presence of a tear may have caused the sensor to wrongly identify it as indicating the home position   copyir.com    Turn off the main power, and check the drive of the intermediate transfer belt; then, turn on the main power   copyir.com
E070-02xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The period of time between when the home position of the intermediate transfer belt is detected and when the next home position is detected is shorter than specified    copyir.com The intermediate transfer belt slips on the drive roller, causing a delay in the timing at which the home position is detected   copyir.com    Turn off the main power, and check the surface of the intermediate transfer belt for a tear; then, turn on the main power   copyir.com
E070-03xx    There is an error in the detection of the ITB home position   copyir.com xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction
The detection of the home position of the intermediate transfer belt has failed once   copyir.com ITB home position sensor B and ITB home position sensor A must occur alternately; however, the same state has been detected continuously   copyir.com    Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then turn on the main power   copyir.com
E073-0001    With the front door closed, the transfer drawer connector or the transfer frame drawer connector is not connected   copyir.com
The result of detecting the feed unit indicates the absence of the unit   copyir.com    Turn off and then on the main power   copyir.com
E077-0001    The home position of the secondary transfer roller (engagement) is not detected   copyir.com
The HP sensor does not go on within 5 sec after the start of a HP search   copyir.com    Turn off and then on the main power   copyir.com
E078-0001    The home position of the transfer belt cleaner unit (engagement) is not detected   copyir.com
The HP sensor does not turn on within 5 sec after the start of a HP search   copyir.com    Turn off and then on the main power   copyir.com
E079-0001    The home position of the outside heating roller is not detected   copyir.com The outside heating roller home position sensor does not go off   copyir.com
The HP sensor does not turn on within 5 sec after the start of an HP search   copyir.com    Turn off and then on the main power   copyir.com
E079-0002    The home position of the outside heating roller is not detected   copyir.com The outside heating roller home position sensor does not go off   copyir.com
If there is an open circuit in the home position sensor of the outside heating roller home position sensor, the state of the sensor will be identified as being ON   copyir.com An error will be identified if the sensor fails to go off when it is at a point where it must normally go on and the outside heating roller shift motor is driven   copyir.com    Turn off and then on the main power   copyir.com
E100-0001    The BD is not detected   copyir.com
The BD signal is not detected when the polygon scanner has been driven for a specific period of time   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E100-0002    The BD is not detected   copyir.com
The BD signal is not detected white the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0001    There is a scanner motor error   copyir.com
The FG signal is not detected within a specific period of time after the polygon scanner has been driven   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0002    There is a scanner motor error   copyir.com
The FG signal is not detected while the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E110-0003    There is a scanner motor error   copyir.com
The FG signal is not detected while the polygon scanner is rotating stably   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E197-0002    There is an error in the communication with the fixing feed PCB   copyir.com
In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E197-0003    There is an error in the communication with the fixing feed PCB   copyir.com
Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E197-0004    There is an error in the communication with the fixing feed PCB   copyir.com
At the start of drum initial multiple rotation, there is no signal indicating the start of 24V in the fixing assembly in the communication between the DC controller and the fixing/feeding unit   copyir.com    Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power   copyir.com
E202-0001    There is an HP error   copyir.com
An error is found during the forward trip of the HP search   copyir.com The scanner HP sensor is faulty   copyir.com The scanner motor is faulty   copyir.com The reader controller is faulty   copyir.com    Check the harness connector for connection; then, as necessary, replace the faulty part   copyir.com
E202-0002    There is an HP error   copyir.com
An error is found during the return trip of the HP search   copyir.com The scanner HP sensor is faulty   copyir.com The scanner motor is faulty   copyir.com The reader controller PCB is faulty   copyir.com    Check the harness connector for connection; then, as necessary, replace the faulty part   copyir.com
E225-0001    The lamp has blown   copyir.com
The level of shading is lower than specified   copyir.com    Check the harness connector for connection   copyir.com Check the scanning lamp (xenon), inverter, and reader controller PCB   copyir.com
E227-0001    There is a power supply (24V) error   copyir.com
At power-on, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0002    There is a power supply (24V) error   copyir.com
At the start of a job, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0003    There is a power supply (24V) error   copyir.com
At the end of a job, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E227-0004    There is a power supply (24V) error   copyir.com
While a load is being driven, the 24V port is off   copyir.com    Check the power supply harness connector for connection; then, as necessary, replace the power supply   copyir.com
E240-0000    There is a DDI-P communication error   copyir.com
There is a DDI-P communication error (error in communication between master and slave 0)   copyir.com    Turn off the main power, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main power   copyir.com
E246-0001    An error has occurred in the course of writing to the counter memory   copyir.com
Normal access to the FRAM PCB is not possible   copyir.com A value is written to a specific area for a check on connection to the FRAM PCB; when read back, however, it is not the value that has been written   copyir.com    Turn off the main power, and check the connection of the counter PCB   copyir.com If the remedy fails, replace the counter PCB   copyir.com
E246-0002    An error has occurred in the course of writing to the counter memory   copyir.com
When the soft ID of FRAM is being repaired, FRAM is not in an initialized condition   copyir.com    Replace the counter PCB   copyir.com
E246-0003    An error has occurred in the course of writing to the counter memory   copyir.com
After an increase in the count, data is read into FRAM; when it is read back and compared, it is not the value that has been read into FRAM   copyir.com    Replace the counter PCB   copyir.com
E246-0004    An error has occurred in the course of writing to the counter memory   copyir.com
A second after repair (from SRAM to FRAM) brings out different SRAM and FRAM counter readings   copyir.com An attempt at repair has failed   copyir.com    Turn off the main power, and check the connector of the counter PCB   copyir.com If repair fails, replace the counter PCB   copyir.com
E247-0001    Error in counter memory or SRAM
An error exists in the SRAM and FRAM counter readings    Replace the counter PCB or SRAM
E248-0000    There is an error in the EEPROM   copyir.com
At time of start-up, a check error has occurred on the SRAM board    Turn off the main power, and check the SRAM board; then, as necessary, replace the SRAM board, and turn on the main power   copyir.com
E248-0001    There is an error in the EEPROM   copyir.com
There is a power-on error   copyir.com    Replace the reader controller PCB   copyir.com
E248-0002    There is an error in the EEPROM   copyir.com
There is a write error   copyir.com    Replace the reader controller PCB   copyir.com
E248-0003    There is an error in the EEPROM   copyir.com
There is a wire/read error   copyir.com    Replace the reader controller PCB   copyir.com
E315-000E    codex error
An error has occurred in the course of software decoding   copyir.com    
E350-0000    Fault in the soft ID PCB/function
An error exists in the add-on parity   copyir.com    Reset in service mode, and replace the soft ID PCB   copyir.com
E350-0001    Fault in the soft ID PCB/function
An error has occurred in the course of full data read operation on the soft ID PCB   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-0002    Fault in the soft ID PCB/function
The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match   copyir.com    Turn off the main power, and replace the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-0003    Fault in the soft ID PCB/function
The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E350-3000    Fault in the soft ID PCB/function
While an E350 error is backed up, the value of the check sum area of all data read from the soft ID PCB and the result of check sum computation do not match   copyir.com    Turn off the main power, and check the connection of the soft ID PCB   copyir.com If the remedy fails, replace the soft ID PCB   copyir.com
E351-0000    There is an error in the main controller PCB (sub)   copyir.com
At start-up, there is an error in the communication between main controller PCB (sub) and the main controller PCB (main)   copyir.com    Turn off the main power, and replace the main controller PCB (sub)   copyir.com If the result is not good, replace the main controller PCB (main), and turn on the main power   copyir.com
E354-0001    Serial No   copyir.com mismatch
All the values of the soft ID 8 digits of SEEPROM are 0x00 or 0xoff   copyir.com    Replace the soft ID PCB   copyir.com
E354-0002    Serial No   copyir.com mismatch
In the absence of an error, the soft ID PCB has been replaced with a new PCB and, in addition, the following conditions exist at the same time: - the soft IDs of the following pairs are not identical: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM   copyir.com - FRAM is not of the initialization pattern (i   copyir.come   copyir.com, the value of the check sum area is '1' but the result of computation of the counter area check sum is not '1')   copyir.com - the soft IDs of the following are all identical: SRAM1, SRAM2, SRAM   copyir.com    A mistake is likely to have been made in the course of counter PCB replacement; as a result, E355 is likely to have occurred thereafter, not permitting recovery despite an attempt to reset E355   copyir.com
E355-0001    Serial No   copyir.com mismatch PCB   copyir.com
The soft IDs of the following pairs are not identical and, in addition, any of the following conditions exist: SEEPROM and SRAM1, SEEPROM and SRAM2, SEEPROM and FRAM   copyir.com - FRAM is of the initialization pattern (i   copyir.come   copyir.com, the value of the check sum area is '1', and the result of check sum computation of the counter area is '1')   copyir.com - the soft ID of any of the following is not identical: SRAM1, SRAM2, FRAM   copyir.com    Reset E355 (if the error occurs in the middle of repair operation)   copyir.com At times, E355 cannot be reset (intentionally designed in such a way to prevent illegal replacement in the field)   copyir.com
E400-0001    There is a DF communication error   copyir.com
There is a check sum error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E400-0002    There is a DF communication error   copyir.com
There is a reception status error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E400-0003    There is a DF communication error   copyir.com
There is a reception interrupt error   copyir.com    Disconnect and connect the harness connector; then, replace the reader controller PCB or the ADF DC controller   copyir.com
E413-0001    There is an error in the DF shift motor   copyir.com
The shift HP sensor is open   copyir.com    Check the harness; then, as necessary, replace the sensor and motor   copyir.com Check the attaching of the parts around the cam   copyir.com
E413-0002    There is an error in the DF shift motor   copyir.com
The shift HP sensor is closed   copyir.com    Check the harness; then, as necessary, replace the sensor and motor   copyir.com Check the attaching of the parts around the cam   copyir.com
E490-0001    The DF is of the wrong model   copyir.com
The installed DF is not of the correct type   copyir.com    Replace the DF with one of an appropriate type   copyir.com
E500-0001    There is a finisher communication error   copyir.com
There is an error in data communication   copyir.com An error has been detected in terms of the number of errors or the duration of the error in the communication between copier and finisher   copyir.com    Turn off the main power, and check the DC controller, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power   copyir.com
E503-0002    There is an error in the communication within the finisher (finisher R1/R2)   copyir.com
There is a data communication error   copyir.com finisher-to-saddle unit communication error    Check the connection between the saddle stitcher controller PCB and the finisher controller PCB   copyir.com
E503-0003    There is an error in the communication within the finisher (finisher R1/R2)   copyir.com
finisher-to-punch unit communication error    Check the connection between the Punch controller PCB and the finisher controller PCB   copyir.com
E505-0001    There is an error in the backup memory of the finisher (finer R1/R2)   copyir.com
There is an error in the data stored in the backup memory    Turn off the main power, and check the DC control, wiring of the finisher PCB, and 24V system fuse; then, turn on the main power   copyir.com
E505-0002    There is an error in the backup memory of the finisher (finer R1/R2)   copyir.com
There is a data error in the punch assembly EEPROM   copyir.com    Turn off the main power, and check the wiring of the DC controller PCB and the puncher controller PCB: then, check the 24V system fuse, and turn back on the main power   copyir.com
E514-8001    There is an error in the trailing edge assist motor (finisher R1/R2)   copyir.com
The home position sensor does not go off when the trailing edge assist motor has been rotated for a specific period of time   copyir.com    1) Check the trailing edge assist home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor   copyir.com Is the wiring normal? 3) Check the trailing edge assist mechanism   copyir.com Is there a fault? 4) Try replacing the trailing edge assist motor   copyir.com Is the problem corrected?
E514-8002    There is an error in the trailing edge assist motor (finisher R1/R2)   copyir.com
The home position sensor does not go on when the trailing edge assist motor has been rotated for a specific period of time   copyir.com    1) Check the trailing edge assist home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the trailing edge assist motor   copyir.com Is the wiring normal? 3) Check the trailing edge assist mechanism   copyir.com Is there a fault? 4) Try replacing the trailing edge assist motor   copyir.com Is the problem corrected?
E519-0002    There is an error in the gear change motor (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate   copyir.com    1) Check the gear change home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor   copyir.com Is the wiring normal? 3) Check the gear change mechanism   copyir.com Is there a fault? 4) Try replacing the gear change motor   copyir.com Is the problem corrected?
E519-8001    There is an error in the gear change motor (finisher R1/R2)   copyir.com
The home position sensor does not go off within a specific period of time after the gear change motor has started to rotate   copyir.com    1) Check the gear change home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor   copyir.com Is the wiring normal? 3) Check the gear change mechanism   copyir.com Is there a fault? 4) Try replacing the gear change motor   copyir.com Is the problem corrected?
E530-8001    There is an error in front alignment (finisher R1/R2)   copyir.com
Th alignment motor has started to rotate   copyir.come home position sensor does not go off within a specific period of time after the front    1) Check the pre-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor   copyir.com Is the problem corrected?
E530-8002    There is an error in front alignment (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate   copyir.com    1) Check the pre-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the pre-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the pre-aligning plate motor   copyir.com Is the problem corrected?
E531-0001    There is an error in stapling (finisher R1/R2)   copyir.com
The home position sensor does not go off within a specific period of time after the stapler motor has started to rotate   copyir.com    1) Check the wiring between the finisher controller PCB and the stapler   copyir.com Is the wiring normal? 2) Try replacing the stapler   copyir.com Is the problem corrected?
E531-0002    There is an error in stapling (finisher R1/R2)   copyir.com
The home position sensor does not go on within a specific period of time after the stapler motor has started to rotate    1) Check the wiring between the finisher controller PCB and the stapler   copyir.com Is the wiring normal? 2) Try replacing the stapler   copyir.com Is the problem corrected?
E532-8001    There is an error in the shift mechanism of the stapler   copyir.com (finisher R1/R2)
The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate   copyir.com    1) Check the stapler shift home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor   copyir.com Is the wiring normal? 3) Check the path of the stapler shift base   copyir.com Is there a mechanical obstacle? 4) Try replacing the stapler shift motor   copyir.com Is the problem corrected?
E532-8002    There is an error in the shift mechanism of the stapler   copyir.com (finisher R1/R2)
The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate   copyir.com    1) Check the stapler shift home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor   copyir.com Is the wiring normal? 3) Check the path of the stapler shift base   copyir.com Is there a mechanical obstacle? 4) Try replacing the stapler shift motor   copyir.com Is the problem corrected?
E535-0003    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
There is an error in relation to an hazardous area   copyir.com   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E535-8001    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E535-8002    There is an error in the staple swing mechanism   copyir.com (finisher R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the swing home position sensor   copyir.com Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor   copyir.com Is the wiring normal? 3) Check the swing mechanism   copyir.com Is there a fault? 4) Try replacing the swing motor   copyir.com Is the problem corrected?
E537-8001    rear alignment error (Finisher-R1/R2)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the post-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor   copyir.com Is the problem corrected?
E537-8002    rear alignment error (Finisher-R1/R2)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time   copyir.com    1) Check the post-aligning plate home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the post-aligning plate motor   copyir.com Is the wiring normal? 3) Check the path of the aligning plate   copyir.com Is there a mechanical obstacle? 4) Try replacing the post-aligning plate motor   copyir.com Is the problem corrected?
E540-8001    upper tray ascent/descent error (Finisher-R1/R2)
upper tray ascent/descent motor clock error    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E540-8002    upper tray ascent/descent error (Finisher-R1/R2)
area error    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E540-8003    upper tray ascent/descent error (Finisher-R1/R2)
safety switch activation    1) Check the No   copyir.com 1 tray area sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between finisher controller PCB and the No   copyir.com 1 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the ascent/descent mechanism of the tray? 4) Try replacing the No   copyir.com 1 tray shift motor   copyir.com Is the problem corrected?
E542-0003    lower tray ascent/descent error (Finisher-R1/R2)
safety switch activation    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E542-8001    lower tray ascent/descent error (Finisher-R1/R2)
lower tray ascent/descent motor clock error    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E542-8002    lower tray ascent/descent error (Finisher-R1/R2)
area error    1) Check the No   copyir.com 2 tray sensors 1 through 3   copyir.com Are the sensors normal? 2) Check the wiring between the finer controller PCB and the No   copyir.com 2 tray shift motor   copyir.com Is the wiring normal? 3) Is there a fault in the tray ascent/descent mechanism? 4) Try replacing the No   copyir.com 2 tray shift motor   copyir.com Is the problem corrected?
E584-0002    shutter unit error (Finisher-R1/R2)
The shutter open/closed sensor does not go on (i   copyir.come   copyir.com, the shutter does not open)   copyir.com    1) Check the shutter home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch   copyir.com Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch   copyir.com Is the problem corrected?
E584-8001    shutter unit error (Finisher-R1/R2)
The shutter open sensor does not go off (i   copyir.come   copyir.com, the shutter is not closed)   copyir.com    1) Check the shutter home position sensor   copyir.com Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stack edging motor and between the finisher controller PCB and the shutter open/close clutch   copyir.com Is the wiring normal? 3) Is there a fault in the shutter mechanism? 4) Try replacing the stack edging motor or the shutter open/close clutch   copyir.com Is the problem corrected?
E590-8001    There is an error in the punch motor   copyir.com (punch unit)
The punching home position sensor is not detected when the punch motor has been driven for 200 msec   copyir.com    Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power   copyir.com
E590-8002    There is an error in the punch motor   copyir.com (punch unit)
The puncher does not detect the punching home position after the motor has stopped (initial operation)   copyir.com    Check the punch home position sensor, horizontal registration motor, and punch driver PCB; then, turn off and then on the main power   copyir.com
E591-8001    There is an error in the punch dust sensor   copyir.com (punch unit)
There is an error in the light   copyir.com    Turn off and then on the main power   copyir.com
E591-8002    There is an error in the punch dust sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com    Turn off and then on the main power   copyir.com
E592-8001    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage at time of light emission   copyir.com (trailing edge sensor)    Turn off and then on the main power   copyir.com
E592-8002    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (trailing edge sensor)    Turn off and then on the main power   copyir.com
E592-8003    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 1)    Turn off and then on the main power   copyir.com
E592-8004    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 1)    Turn off and then on the main power   copyir.com
E592-8005    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 2)    Turn off and then on the main power   copyir.com
E592-8006    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 2)    Turn off and then on the main power   copyir.com
E592-8007    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage it the presence of emission of light   copyir.com (horizontal registration sensor 3)    Turn off and then on the main power   copyir.com
E592-8008    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 3)    Turn off and then on the main power   copyir.com
E592-8009    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage with emission of light   copyir.com (horizontal registration sensor 4)    Turn off and then on the main power   copyir.com
E592-800A    There is an error in the punch horizontal registration sensor   copyir.com (punch unit)
There is an error in the light-receiving voltage without emission of light   copyir.com (horizontal registration sensor 4)    Turn off and then on the main power   copyir.com
E593-8001    There is an error in the punch shift motor   copyir.com (punch unit)
The light-receiving voltage HP sensor does not go off at time of light emission   copyir.com    Turn off and then on the main power   copyir.com
E593-8002    There is an error in the punch shift motor   copyir.com (punch unit)
The light-receiving voltage HP sensor doest not go on without emission of light   copyir.com    Turn off and then on the main power   copyir.com
E5F0-0001    There is an error in saddle paper positioning   copyir.com
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1   copyir.com33 sec   copyir.com The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty   copyir.com    Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S)   copyir.com
E5F0-0002    There is an error in saddle paper positioning   copyir.com
The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec   copyir.com The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty   copyir.com    Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S)   copyir.com
E5F1-0001    There is an error in saddle paper folding   copyir.com
The number of detection pulses of the paper folding motor clock sensor is lower than specified   copyir.com The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty   copyir.com    Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S)   copyir.com
E5F1-0002    There is an error in saddle paper folding   copyir.com
The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec   copyir.com The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty   copyir.com    Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S)   copyir.com
E5F2-0001    There is an error in the saddle guide   copyir.com
The guide home position sensor does not turn on when the guide motor has been driven for 0   copyir.com45 sec   copyir.com The guide motor (M3S) or the guide home position sensor (PI3S) is faulty   copyir.com    Check the guide motor (M3S) /guide home position sensor (PI13S)   copyir.com
E5F2-0002    There is an error in the saddle guide   copyir.com
The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec   copyir.com The guide motor (M3S) or the guide home position sensor (PI3S) is faulty   copyir.com    Check the guide motor (M3S) /guide home position sensor (PI13S)   copyir.com
E5F3-0001    There is an error in saddle alignment   copyir.com
The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05   copyir.com sec (during initialization, 1   copyir.com67 sec)   copyir.com The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty   copyir.com    Check the alignment motor (M5S) /aligning plate home position sensor (PI5S)   copyir.com
E5F3-0002    There is an error in saddle alignment   copyir.com
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec   copyir.com The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty   copyir.com    Check the alignment motor (M5S) /aligning plate home position sensor (PI5S)   copyir.com
E5F4-0001    There is an error in saddle rear sampling   copyir.com
The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0   copyir.com5 sec or more   copyir.com The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty   copyir.com    Check he stitching motor (rear; M6S) /stitching home position sensor (rear; M
E5F4-0002    There is an error in saddle rear sampling   copyir.com
The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0   copyir.com5 sec or more   copyir.com The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty   copyir.com    Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S)   copyir.com
E5F5-0001    There is an error in saddle front stapling   copyir.com
The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0   copyir.com5 sec or more   copyir.com The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty   copyir.com    Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S)   copyir.com
E5F5-0002    There is an error in saddle front stapling   copyir.com
The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0   copyir.com5   copyir.com The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty   copyir.com    Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S)   copyir.com
E5F6-8001    There is an error in saddle butting   copyir.com
The paper pushing plate home position sensor does not turn on when the paper pushing motor has been driven for 0   copyir.com3 sec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4) is faulty   copyir.com
E5F6-8002    There is an error in saddle butting   copyir.com
The paper pushing plate home position sensor does not turn off when paper pushing plate motor has been driven for 80 msec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty   copyir.com
E5F6-8003    There is an error in saddle butting   copyir.com
The number of detection pulses of the paper pushing plate motor clock sensor drops below a specific number   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty   copyir.com
E5F6-8004    There is an error in saddle butting   copyir.com
The paper pushing plate sensor does not turn off when the paper pushing plate motor has been driven for 80 msec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty   copyir.com
E5F6-8005    There is an error in saddle butting   copyir.com
The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0   copyir.com3 sec or more   copyir.com The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty   copyir.com    The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI5S) is faulty   copyir.com
E5F8-0001    There is an error in the saddle connector   copyir.com
The connector of the guide home position sensor is identified as being disconnected   copyir.com The connector of the guide home position sensor (PI3S) is faulty   copyir.com    Check the connectors of the guide home position sensor (PI13S)   copyir.com Check the connectors of the paper pushing plate home position sensor (PI4S)   copyir.com
E5F8-0002    There is an error in the saddle connector   copyir.com
The connector of the paper pushing plate home position sensor is identified as being disconnected   copyir.com The connector of the paper pushing plate home position sensor (PI14S) is faulty   copyir.com    Check the connectors of the paper pushing plate leading edge position sensor (PI5S)   copyir.com
E5F8-0003    There is an error in the saddle connector   copyir.com
The connector of the paper pushing plate leading edge position sensor is identified as being disconnected   copyir.com The connector of the paper pushing plate leading edge sensor (PI15S) is faulty   copyir.com    Check the connectors of the paper pushing plate leading edge position sensor (PI5S)   copyir.com
E5F9-0001    There is an error in the saddle switch   copyir.com
With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open   copyir.com The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty   copyir.com    Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S)   copyir.com
E5F9-0002    There is an error in the saddle switch   copyir.com
With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty   copyir.com    Check the front cover switch (MS2S)/delivery cover switch (MS3S)   copyir.com
E5F9-0003    There is an error in the saddle switch   copyir.com
With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S)    Check the delivery cover switch (MS3S)   copyir.com
E602    There is a hard disk error   copyir.com    
E604-0000    There is a shortage of image memory (SDRAM)   copyir.com
The amount of memory required by the model in question is not recognized   copyir.com    Set it to the size of memory suited to the model in question   copyir.com
E609-0008    Samsung HDD-related error code
The HDD does not increase to a specific temperature level within a specific time when the power is turned on   copyir.com    Replace the HDD   copyir.com
E609-0009    Samsung HDD-related error code
The HDD does not increase to a specific temperature level in relation to a sleep state   copyir.com    Turn off and then on the power   copyir.com If the return operation fails, replace the HDD   copyir.com
E610    HDD encryption key fault    
E674-0001    There is an error in the fax board   copyir.com
The fax board is detected, but communication is not possible   copyir.com    Turn off the main power, and check the fax board and the main controller PCB; then, turn on the main power   copyir.com If the machine fails to reset, replaced the fax board or the main controller PCB
E677-0003    There is an external controller error   copyir.com
An error has been detected by a check on the configuration when the external controller is being started up   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to start up, re-install the system software of the external contro
E677-0010    There is an external controller error   copyir.com
A controller for a non-Canon machine is connected   copyir.com    Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power   copyir.com If the machine fails to reset, re-install the system software of the external controller   copyir.com
E677-0080    There is an external controller error   copyir.com
There is an error in the communication with the printer after the external controller has started up normally   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to start up, re-install the system software of the external controller   copyir.com
E710-0001    There is an error in IPC initialization   copyir.com
The machine fails to become ready within 3 sec after the IPC chip has started up   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.comted up   copyir.com
E711-0002    There is an IPC communication error   copyir.com
An error has been detected 4 times or more within 1   copyir.com5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset   copyir.com    Turn off the main power, and check the cable; then, turn on the main power   copyir.com If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller   copyir.com
E713-0001    There is a finisher communication error   copyir.com
There is an error in the IC used for communication by the sorter   copyir.com    Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch   copyir.com If the machine does not reset, replace the DC controller PCB/finisher controller PCB   copyir.com
E717-0001    There is an error in the communication with the NE controller   copyir.com
The NE controller that was connected before the power is turned off is not recognized after the power is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E717-0002    There is an error in the communication with the NE controller   copyir.com
An IPC open circuit or an IPC communication error is not reset   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0001    error in communication with coin vendor/card reader
The coin vendor that is connected before the power is turned off is not recognized when the paper is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0002    error in communication with coin vendor/card reader
- The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered   copyir.com - There is an open circuit in the pickup delivery signal line   copyir.com - An improper connection is detected (short circuit between Tx and Rx of IPC)   copyir.com    Check the cable; thereafter, reset by making the following selections: COPIER>FUNCTION>CLEAR>ERROR
E719-0011    error in communication with coin vendor/card reader
The card reader that is connected before the power is turned off is not recognized when the paper is turned on   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E719-0012    error in communication with coin vendor/card reader
There is an IPC cable open circuit or an IPC communication error in relation to the card reader that cannot be reset   copyir.com    Check the cable, and reset in service mode: COPIER>FUNCTION>CLEAR>ERR   copyir.com
E730    There is a PDL error   copyir.com    
E731    There is a UFR board error   copyir.com    Turn off the main power, and check the connection of the UFR board; then, turn on the main power   copyir.com If the machine does not reset, replace the UFR board or the main controller PCB   copyir.com
E732-0001    There is an error in reader communication   copyir.com
There is an error in reader communication   copyir.com    Turn off the main power, and check the connectors to the reader, and check the power supply of the reader; then, turn on the main power   copyir.com
E732-9999    There is an error in reader communication   copyir.com
Although a printer model, the machine is identified as a reader unit at start-up   copyir.com (A copier model is started up as a printer model when the RAM is initialized   copyir.com)    Turn off and then on the main power   copyir.com
E733-0000    There is a printer communication error   copyir.com
There is a printer communication error   copyir.com At start-up, the printer is not detected   copyir.com    Turn off the main power, and check the connectors to the DC controller PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power   copyir.com
E733-0001    There is a printer communication error   copyir.com
There is a DDI-P communication error   copyir.com    Turn off the main power, and check the connectors to the DC control PCB and the main controller PCB, and check the power supply of the printer; then, turn on the main power   copyir.com
E740-0002    There is an Ethernet board error   copyir.com
At time of start-up, the MAC address is found to be illegal   copyir.com A non-Canon MAC address is detected   copyir.com    Turn off the main power, and replace the NIC; then, turn on the main power
E743-0000    There is a DDI communication error   copyir.com
There is an SCI error   copyir.com The reception data is faulty   copyir.com A reception time-out condition has occurred   copyir.com An SEQ timeout error has occurred   copyir.com An SEQ time-out error has occurred   copyir.com    Disconnect and connect the DDI-S cable connector; then, as necessary, replace the reader controller PCB or the main controller PCB   copyir.com
E744    There is a language file/boot ROM error   copyir.com    Download the appropriate language fields of the correct version using the Service Support Tool
E745    There is a TokenRing error   copyir.com    
E746-0003    The accessories board is of the wrong type   copyir.com
At time of start-up, the UFR board is found to be of the wrong type   copyir.com (A query is made to find out if the type is correct with reference to the engine ID   copyir.com)    Replace it with a UFR board of the correct type   copyir.com
E746-0004    The accessories board is of the wrong type   copyir.com
At time of start-up, the scanner board is found to be of the wrong type   copyir.com (A query is made to find out if the type is correct with reference to the engine ID   copyir.com)    Replace it with a scanner board of the correct type   copyir.com
E747    There is an error in the ASIC for image processing or in the ASIC for memory control/communication control   copyir.com
There is an error in IC1015 (ASIC for image processing) or in IC1012 (for memory control/communication control) on the main controller PCB   copyir.com (e   copyir.comg   copyir.com, image data transfer error)    Turn off the main power, and check the main controller PCB; then, turn on the main controller PCB
748    CL2 board-dependent board error    1   copyir.com Disconnect and then connect 4 to 5 G-chip boards several times   copyir.com 2   copyir.com Replace the G-chip board   copyir.com 3   copyir.com Replace the main controller PCB   copyir.com
E749-0001    Reboot instruction initiated by change in PDL configuration
A change has occurred that calls for turning off and then on the power   copyir.com    Turn off and then on the power   copyir.com
E800-0001    The interlock 24V mechanism of the fixing unit is identified as being off   copyir.com With the door closed, the interlock 24V mechanism remains off for 500 msec   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB, check the fixing unit interlock, and check the 24V system fuse; then, turn on the interlock main switch   copyir.com
E804-0004    There is any of the various types of fan errors   copyir.com
There is an error in the controller cooling fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E804-0007    There is any of the various types of fan errors   copyir.com
There is an error in the power supply cooling fan   copyir.com    Turn off the main switch, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E805-0003    The fixing heat exhaust fan is identified as having stopped or having an error   copyir.com
There is an error in the fixing heat exhaust fan   copyir.com    Turn off the main power, and check the supply of power to the fan; then, as necessary, replace the fan, and turn on the main power   copyir.com
E820-0002    There is an error in the process unit cooling fan   copyir.com
There is an error in the process unit fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E824-0000    There is an error in the primary charging suction/primary charging exhaust fan   copyir.com
There is an error in the primary charging suction mechanism   copyir.com    Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch   copyir.com
E824-0001    There is an error in the primary charging suction/primary charging exhaust fan   copyir.com
There is an error in the primary exhaust fan   copyir.com    Turn off the main switch, and check the wiring of the DC controller PCB and 2V system fuse; then, turn on the main switch   copyir.com

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب