Your browser does not support JavaScript! > سرویس مانوئل کانون

   کانال تلگرام کپی ایران

(0) محصول
سرویس مانوئل کانون
دوشنبه, 10 اسفند 1394 10:48

کانون Canon iR7200

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-0000    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor is less than 70 deg C 3   copyir.ocm5 min after power on   copyir.ocm    Check the mounting/soiling of the main thermistor   copyir.ocm Replace the fixing heater   copyir.ocm Replace the main thermistor   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E000-0010    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E001-0001    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)   copyir.ocm
The reading of the main thermistor or the sub thermistor is 230 deg C or more for 2 sec   copyir.ocm (hardware detection)    Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E001-0002    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)   copyir.ocm
The reading of the main thermistor or the sub thermistor is 230 deg C or more for 2 sec or more   copyir.ocm (software detection)    Check the mounting/soiling of the main thermistor   copyir.ocm Replace the main thermistor   copyir.ocm Replace the sub thermistor   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E001-0003    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)   copyir.ocm
The difference in the readings of the main thermistor and the sub thermistor is 50 deg C for 1 sec   copyir.ocm (main thermistor reading>sub thermistor reading)    Check the mounting/soiling of the main thermistor   copyir.ocm Replace the main thermistor   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E001-0004    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)   copyir.ocm
The difference in the readings of the main thermistor and the sub thermistor is 50 deg C for 1 sec or more   copyir.ocm (main thermistor reading>/=sub thermistor reading)    Check the mounting/soiling of the main thermistor   copyir.ocm Replace the main thermistor   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E001-0010    The fixing unit has overheated   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)   copyir.ocm
The power has been turned off and then on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E002-0000    The fixing unit has overheated   copyir.ocm After correcting the error, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 70 deg C, but does not reach 100 deg C within 2   copyir.ocm5 sec thereafter   copyir.ocm    Disconnect and then connect J508 of the DC controller PCB   copyir.ocm Disconnect and then connect the connectors of the fixing unit   copyir.ocm Check the wiring between the main/sub thermistor and the DC controller   copyir.ocm Check the mounting/soiling of the main thermistor   copyir.ocm Replace the fixing heater   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E002-0001    The fixing unit has overheated   copyir.ocm After correcting the error, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 100 deg C, but does not reach 150 deg C within 2   copyir.ocm5 min thereafter)    Disconnect and then connect J508 of the DC controller PCB   copyir.ocm Disconnect and then connect the connectors of the fixing unit   copyir.ocm Check the wiring between the main/sub thermistor and the DC controller   copyir.ocm Check the mounting/soiling of the main thermistor   copyir.ocm Replace the fixing heater   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E002-0010    The fixing unit has overheated   copyir.ocm After correcting the error, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E003-0000    The fixing unit temperature is abnormally low   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 100 deg C, but is 70 deg C or less for 2 sec thereafter   copyir.ocm    Disconnect and then connect J508 of the DC controller PCB   copyir.ocm Disconnect and then connect the connectors of the fixing unit   copyir.ocm Check the wiring between the main/sub thermistor and the DC controller PCB   copyir.ocm Check the mounting/soiling of the main thermistor   copyir.ocm Replace the fixing heater   copyir.ocm Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E004-0000    The fixing unit has a fault   copyir.ocm (protective circuit ON) After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
While the sub heater is on, the SSR for the heater drive has a short-circuit for 5 sec or more   copyir.ocm    Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E004-0001    The fixing unit has a fault   copyir.ocm (protective circuit ON) After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
While the main heater is on, the SSR for the heater drive has a short-circuit for 5 sec or more   copyir.ocm    Replace the AC driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E005-0000    The fixing web has run out   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of the fixing web has been detected for 5 sec or more   copyir.ocm    Check the position of the fixing web detecting lever   copyir.ocm Replace the fixing web   copyir.ocm Replace the fixing web length sensor   copyir.ocm Replace the DC controller PCB   copyir.ocm If you have replaced the fixing web, be sure to reset the counter: - COPIER>COUNTER>MISC>FIX-WEB - COPIER>COUNTER>DRBL-1>FX-WEB
E005-0010    The fixing web has run out   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E010-0000    The main motor rotation is faulty   copyir.ocm
After the main motor has gone on, the FG signal of the motor is not detected for 2 sec or more   copyir.ocm    Disconnect and then connect J611 and J612 of the main motor   copyir.ocm Disconnect and then connect J514 of the DC controller PCB   copyir.ocm Disconnect and then connect J1720 of the relay PCB   copyir.ocm Replace the main motor   copyir.ocm Replace the relay PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E012-0000    The drum motor rotation is faulty   copyir.ocm
After the drum motor has gone on, the PLL lock signal of the motor is not detected for 2 sec or more   copyir.ocm    Disconnect and then connect J1721 of the relay PCB   copyir.ocm Disconnect and then connect J512 of the DC controller PCB   copyir.ocm Disconnect and then connect J601 and J602 of the drum motor   copyir.ocm Replace the drum motor   copyir.ocm Replace the DC controller PCB   copyir.ocm
E013-0000    The waste toner feedscrew is stuck   copyir.ocm (clogged with waste toner) After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The waste toner feedscrew is stuck for 4 sec or more   copyir.ocm    Detach and then attach the waste toner pipe   copyir.ocm Replace the waste toner pipe   copyir.ocm Replace the waste toner feedscrew detecting switch   copyir.ocm Replace the DC controller PCB   copyir.ocm
E013-0010    The waste toner feedscrew is stuck   copyir.ocm (clogged with waste toner) After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E014-0000    The fixing motor rotation is faulty   copyir.ocm
After the fixing motor has gone on, the PLL signal of the motor is not detected for 2 sec or more   copyir.ocm    Disconnect and then connect J651 and J652 of the fixing motor   copyir.ocm Replace the fixing motor   copyir.ocm Replace the relay PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E015-0000    The pickup motor rotation is faulty   copyir.ocm
The pickup motor has gone on, but the FG signal of the motor is not detected for 2 sec or more   copyir.ocm    Disconnect and then connect J621 and J622 of the pickup motor   copyir.ocm Replace the pickup motor   copyir.ocm Replace the relay PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E019-0000    The waste toner case is full   copyir.ocm
After the waste toner case has become full, 50,000 prints (A4) or more have been made without disposing of the waste toner   copyir.ocm    Dispose of the waste toner   copyir.ocm Check the operation of the waste toner bottle base   copyir.ocm Disconnect and then connect J514 of the DC controller PCB   copyir.ocm Replace the waste toner case full sensor   copyir.ocm Replace the DC controller PCB   copyir.ocm
E020-0001    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside the developing assembly is detected of 120 sec or more even when toner supply operation has been executed for the assembly   copyir.ocm    Disconnect and then connect the connector (J504, J512) of the DC controller PCB   copyir.ocm Replace the developing cylinder clutch (CL4)   copyir.ocm Replace the buffer motor (M18)   copyir.ocm Replace the magnet roller drive clutch (CL1)   copyir.ocm
E020-0002    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner in the buffer is detected for 60 sec even after toner supply operation for the buffer has been executed and when there is toner inside the hopper   copyir.ocm    Disconnect and connect the connector (J504, J511) of the DC controller PCB   copyir.ocm Replace the buffer motor (M18)   copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2)   copyir.ocm
E020-0003    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside the buffer is detected for 210 sec or more even when there is toner inside the sub hopper and after toner supply operation of that buffer following the replacement of the toner bottle   copyir.ocm    Disconnect and connect the connector (J504, J511) of the DC controller PCB   copyir.ocm Replace the buffer motor (M18)   copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2)   copyir.ocm
E020-0004    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside he buffer is detected for 150 sec or more even when there is toner inside the buffer and after toner supply operation has been executed for the buffer following the replacement of the toner bottle   copyir.ocm    Disconnect and connect the connector (J504, J511) of the DC controller PCB   copyir.ocm Replace the buffer motor (M18)   copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2)   copyir.ocm
E020-0005    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is executed, the developing assembly inside toner sensor does not detect the presence of toner    Disconnect and then connect the connector (J504) of the DC controller PCB   copyir.ocm Replace the developing assembly inside toner sensor (TS3)   copyir.ocm
E020-0006    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is executed, the developing assembly inside toner sensor detects the presence of toner, but it does not detect the presence for 600 sec or more thereafter   copyir.ocm    Disconnect and then connect the connector (J504) of the DC controller PCB   copyir.ocm Replace the developing assembly inside toner sensor (TS3)   copyir.ocm
E020-0007    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installing mode (COVER>FUNCTION>INSTALL>TONER-S) is executed, the buffer inside toner sensor does not detect the presence of toner for 60 sec or more   copyir.ocm    Disconnect and connect the connector (J504, J511) of the DC controller PCB   copyir.ocm Replace thetoner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1)   copyir.ocm
E020-0008    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When the toner feed motor (sub hopper) is driven, a fault is detected for 3 sec or more for the motor   copyir.ocm    Disconnect and connect the connector (J511) of the DC controller PCB   copyir.ocm Replace the toner feed motor (sub hopper; M22)   copyir.ocm
E020-0009    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
There is a fault in the rotation of the buffer motor   copyir.ocm    Disconnect and then connect the connector (J504) of the DC controller PCB   copyir.ocm Replace the buffer motor (M18)   copyir.ocm
E020-0010    The developing assembly is out of toner   copyir.ocm The buffer motor rotation is faulty   copyir.ocm The toner feed motor (sub hopper) rotation is faulty   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error   copyir.ocm    Reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E025-0000    The toner bottle motor rotation is faulty   copyir.ocm
A toner bottle motor error (over-current) is detected for 10 sec for a second time   copyir.ocm MEMO: The 1st detection of the error will cause the machine to indicate the message "Shake and Replace the Toner Container   copyir.ocm"    Disconnect and then connect J512 of the DC controller PCB   copyir.ocm
E025-0001    The toner bottle motor rotation is faulty   copyir.ocm
The toner bottle motor is not connected   copyir.ocm    Disconnect and then connect J512 of the DC controller PCB   copyir.ocm
E032-0001    The copy data controller/NE controller counter fails to operate   copyir.ocm
An open circuit of the counter signal has been detected   copyir.ocm    Disconnect and then connect J1022 of the main controller PCB   copyir.ocm Replace the copy data controller/NE controller   copyir.ocm Replace the main controller PCB   copyir.ocm
E043-0000    The rotation of the pickup motor of the side paper deck is faulty   copyir.ocm
The side paper deck pickup motor has gone on, but the PLL lock signal is not detected for 2 sec or more (1st detection)   copyir.ocm MEMO: For the 2nd and subsequent detection, the machine will indicate "E043" on the screen offering a choice of sources of paper   copyir.ocm    Disconnect and then connect J101 and J106 of the side paper deck driver PCB   copyir.ocm Replace the pickup motor   copyir.ocm Replace the side paper deck driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E051-0001    The horizontal registration HP detection has an error   copyir.ocm
After the start of horizontal registration HP detection, the HP sensor is not off within 5 sec (i   copyir.ocme   copyir.ocm, not leaving home position)   copyir.ocm MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam   copyir.ocm    At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec   copyir.ocm
E051-0002    The horizontal registration HP detection has an error   copyir.ocm
After the start of horizontal registration HP detection, the home position is not detected within 5 sec   copyir.ocm MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam   copyir.ocm    At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec   copyir.ocm
E051-0003    The horizontal registration HP detection has an error   copyir.ocm
Replace the horizontal registration HP sensor   copyir.ocm Replace the horizontal registration motor   copyir.ocm Replace the stackless transport driver PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm    At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec   copyir.ocm
E065-0000    The high-voltage output has a fault   copyir.ocm (primary charging assembly)
A fault (leak) is detected when high voltage is supplied to the primary charging assembly   copyir.ocm    Remove and then mount the primary charging assembly   copyir.ocm Check for soiling   copyir.ocm Disconnect and then connect T601, J723, and J731 of the HV-DC PCB   copyir.ocm Replace the HV-DC PCB   copyir.ocm
E067-0000    The high-voltage output has a fault   copyir.ocm
A fault is detected at the same time in 2 of the following: primary high voltage, pre-transfer high voltage, transfer high voltage, separation high voltage   copyir.ocm    Remove and mount the primary charging assembly   copyir.ocm Remove and mount the pre-transfer charging assembly   copyir.ocm Remove and mount the transfer/ separation charging assembly   copyir.ocm Disconnect and then connect J721, J723, J731, and J734 of the HV-DC PCB   copyir.ocm Replace the HV-DC PCB   copyir.ocm Replace the HV-AC PCB   copyir.ocm
E068-0000    The high-voltage output has a fault   copyir.ocm (separation charging assembly)
A fault (leak) has been detected while the separation charging assembly is being supplied with high voltage   copyir.ocm    Remove and mount the transfer/separation charging assembly   copyir.ocm Disconnect and then connect J7233 and J734 of the HV-DC PCB   copyir.ocm Disconnect and then connect J741 and J742 of the HV-AC PCB   copyir.ocm Replace the HV-AC PCB   copyir.ocm Replace the transfer/ separation charging assembly   copyir.ocm Replace the pre-transfer charging assembly   copyir.ocm
E069-0000    The transfer high voltage has an error   copyir.ocm
A fault (leak) has been detected while the transfer charging assembly is being supplied with high voltage   copyir.ocm    Remove and mount the transfer/separation charging assembly   copyir.ocm Check for soiling   copyir.ocm Disconnect and then connect T701 and J723 of the HV-DC PCB   copyir.ocm Replace the HV-DC PCB   copyir.ocm Replace the pre-transfer charging assembly   copyir.ocm
E102-0001    A read error has occurred in relation to the laser scanner unit EEPROM data   copyir.ocm
The correction data cannot be read from the EEPROM of the laser scanner unit   copyir.ocm    Disconnect and then connect the connector of the video PCB   copyir.ocm Disconnect and then connect the DC controller PCB   copyir.ocm Replace the laser scanner unit   copyir.ocm
E110-0000    The laser scanner motor rotation has a fault   copyir.ocm
After the laser scanner motor has gone on, the PLL lock signal of the motor is not detected for 15 sec or more   copyir.ocm    Check to see if all covers have been attached to the primary charging assembly   copyir.ocm Disconnect and then connect J764 of the laser scanner motor drive PCB (in the laser scanner unit)   copyir.ocm Disconnect and then connect J1401 of the video PCB   copyir.ocm Disconnect and then connect J506 of the DC controller PCB   copyir.ocm Replace the laser scanner unit   copyir.ocm Replace the video PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E111-0000    The laser scanner motor cooling fan rotation has a fault   copyir.ocm
After the laser scanner motor cooling fan has gone on, the fan stop signal is detected for 5 sec or more   copyir.ocm    Disconnect and then connect J503 of the DC controller PCB   copyir.ocm Replace the laser scanner motor cooling fan   copyir.ocm Replace the DC controller PCB   copyir.ocm
E121-0001    A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2   copyir.ocm
The laser scanner unit cooling fan has a fault   copyir.ocm After the laser scanner unit cooling fan has gone on, the fan stop signal is detected for 5 sec or more   copyir.ocm    Disconnect and then connect J503 of the DC controller PCB   copyir.ocm Replace the laser scanner unit cooling fan   copyir.ocm Replace the DC controller PCB   copyir.ocm
E121-0002    A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2   copyir.ocm
The reader heat discharge fan 1 has a fault   copyir.ocm After the reader heat discharge fan 1 has gone on, the fan stop signal is detected for 5 sec or more   copyir.ocm    Connect and then disconnect J512 of the DC controller PCB   copyir.ocm Replace the reader heat discharge fan 1   copyir.ocm Replace the DC controller PCB   copyir.ocm
E121-0003    A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2   copyir.ocm
The reader heat discharge fan 2 has a fault   copyir.ocm After the reader heat discharge fan 2 has gone on, the fan stop signal is detected for 5 sec or more   copyir.ocm    Disconnect and then connect J521 of the DC controller PCB   copyir.ocm Replace the reader heat discharge fan 2   copyir.ocm Replace the DC controller PCB   copyir.ocm
E197-0000    The laser scanner motor communication has a fault   copyir.ocm
The communication with the laser control IC is not normal   copyir.ocm    Replace the laser scanner unit   copyir.ocm Replace the video PCB   copyir.ocm
E202-0001    The scanner HP detection mechanism has a fault   copyir.ocm
At time of shading, the intensity of light is below the standard level   copyir.ocm    Disconnect and then connect the connector of the scanner HP sensor   copyir.ocm Replace the scanner HP sensor   copyir.ocm Replace the scanner motor   copyir.ocm Replace the reader controller PCB   copyir.ocm
E202-0002    The scanner HP detection mechanism has a fault   copyir.ocm
In ADF mode, the intensity of light is below the standard level between sheets   copyir.ocm    Disconnect and then connect the connector of the scanner HP sensor   copyir.ocm Replace the scanner HP sensor   copyir.ocm Replace the scanner motor   copyir.ocm Replace the reader controller PCB   copyir.ocm
E227-0001    The reader unit power supply (24 V) has a fault   copyir.ocm
At power-on, the 24V port is off   copyir.ocm    Disconnect and then connect the reader power supply connector   copyir.ocm Replace the power supply   copyir.ocm
E227-0002    The reader unit power supply (24 V) has a fault   copyir.ocm
At the start of a job, the 24V port is off   copyir.ocm    Disconnect and then connect the reader power supply connector   copyir.ocm Replace the power supply   copyir.ocm
E227-0003    The reader unit power supply (24 V) has a fault   copyir.ocm
At the end of a job, the 24V port is off   copyir.ocm    Disconnect and then connect the reader power supply connector   copyir.ocm Replace the power supply   copyir.ocm
E227-0004    The reader unit power supply (24 V) has a fault   copyir.ocm
While a load is driven, the 24V port is off   copyir.ocm    Disconnect and then connect the reader power supply connector   copyir.ocm Replace the power supply   copyir.ocm
E240-0000    A fault exists in the communication between the main controller and the DC controller   copyir.ocm
A fault has occurred in the communication between the CPUs of the main controller and the DC controller   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the DC controller PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E248-0000    A fault exists in the following: main controller SRAM, reader controller EEPROM   copyir.ocm
At start-up, an SRAM check error has occurred   copyir.ocm    Replace the main controller PCB   copyir.ocm
E248-0001    A fault exists in the following: main controller SRAM, reader controller EEPROM   copyir.ocm
An error has occurred at time of power-on (EEPROM)   copyir.ocm    Replace the reader controller PCB   copyir.ocm
E248-0002    A fault exists in the following: main controller SRAM, reader controller EEPROM   copyir.ocm
An error has occurred during write operation (EEPROM)   copyir.ocm    Replace the reader controller PCB   copyir.ocm
E248-0003    A fault exists in the following: main controller SRAM, reader controller EEPROM   copyir.ocm
A read error has occurred after write operation (EEPROM)   copyir.ocm    Replace the reader controller PCB   copyir.ocm
E251-0000    The inverter cooling fan rotation is faulty   copyir.ocm    Disconnect and then connect J1110 of the reader controller PCB   copyir.ocm Replace the inverter cooling fan   copyir.ocm Replace the reader controller PCB   copyir.ocm
E302-0000    Shading operation is faulty   copyir.ocm
In the course of shading operation, the processing doses not end within the reader controller   copyir.ocm    Disconnect and then connect J1107 and J1108 of the reader controller PCB   copyir.ocm Replace the reader controller PCB   copyir.ocm
E315-0007    The image data codec has a fault   copyir.ocm
A JBIG encoder error has occurred   copyir.ocm    Replace the main controller PCB   copyir.ocm
E315-000d    The image data codec has a fault   copyir.ocm
A JBIG decoding error has occurred   copyir.ocm    Replace the DDR-SDRAM   copyir.ocm Replace the HDD   copyir.ocm Replace the main controller PCB   copyir.ocm
E315-000e    The image data codec has a fault   copyir.ocm
An error has occurred in the course of software decoding   copyir.ocm    Replace the DDR-SDRAM   copyir.ocm Replace the HDD   copyir.ocm Replace the main controller PCB   copyir.ocm
E315-0100    The image data codec has a fault   copyir.ocm
An overrun error has occurred   copyir.ocm    Replace the main controller PCB   copyir.ocm
E315-0200    The image data codec has a fault   copyir.ocm
The open I/F relay PCB has detected an error (no recovery after a retry)   copyir.ocm    Replace the open I/F relay PCB (relay PCB between the main controller and PS controller)   copyir.ocm
E315-0300    The image data codec has a fault   copyir.ocm
Cubic time-out    Turn off and then back on he power   copyir.ocm Replace the main controller PCB   copyir.ocm
E315-0400    The image data codec has a fault   copyir.ocm
Shift Device A time-out    Turn off and then back on he power   copyir.ocm Replace the main controller PCB   copyir.ocm
E315-0401    The image data codec has a fault   copyir.ocm
Shift Device B time-out    Turn off and then back on he power   copyir.ocm Replace the main controller PCB   copyir.ocm
E351-0000    An error has occurred in the main controller communication   copyir.ocm
At start-up, a main controller communication error has occurred   copyir.ocm    Replace the main controller PCB   copyir.ocm
E400-0001    An ADF communication error has occurred   copyir.ocm
A check sum error has occurred   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the reader controller PCB   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E400-0002    An ADF communication error has occurred   copyir.ocm
A reception status error has occurred   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the reader controller PCB   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E400-0003    An ADF communication error has occurred   copyir.ocm
A reception interrupt error has occurred   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the reader controller PCB   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E402-0000    The ADF belt motor rotation is faulty   copyir.ocm
While the belt motor drive signal is on, no lock signal occurs for 100 msec   copyir.ocm    Disconnect and then connect the cable between the belt motor driver PCB and the ADF controller PCB   copyir.ocm Replace the belt motor clock sensor   copyir.ocm Replace the belt motor clock sensor   copyir.ocm Replace the belt motor   copyir.ocm Replace the belt motor driver PCB   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E404-0000    The ADF delivery motor rotation is faulty   copyir.ocm
When the delivery motor drive signal is on, no clock signal occurs for 200 msec    Replace the delivery motor   copyir.ocm Replace the delivery motor clock sensor   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E405-0000    The ADF separation motor rotation is faulty   copyir.ocm
When the separation motor drive signal is on, no clock signal occurs for 200 msec   copyir.ocm    Replace the separation motor   copyir.ocm Replace the separation motor clock sensor   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E410-0000    The ADF pickup motor rotation is faulty   copyir.ocm
No signal occurs from the following sensors within 2 sec after the pickup motor is driven: - pickup roller height sensor 1 (PI8), pickup roller height sensor 2 (PI9) - pickup roller HP sensor (PI7)    Replace the pickup motor   copyir.ocm Replace the pickup roller height sensor (PI8)   copyir.ocm Replace the pickup roller height sensor 2 (PI9)   copyir.ocm Replace the pickup roller HP sensor (PI7)   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E413-0001    The ADF shift motor rotation is faulty   copyir.ocm
The shift motor HP sensor is open   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the shift motor HP sensor   copyir.ocm Replace the shift motor   copyir.ocm
E413-0002    The ADF shift motor rotation is faulty   copyir.ocm
Shift motor HP sensor is closed   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Replace the shift motor HP sensor   copyir.ocm Replace the shift motor   copyir.ocm
E420-0000    An ADF EEPROM read error has occurred   copyir.ocm
At power-on, an attempt to read the EEPROM backup data fails   copyir.ocm Or, data that has been read has a fault   copyir.ocm    Replace the ADF controller PCB   copyir.ocm
E490-0001    The ADF is of the wrong type   copyir.ocm    Replace the ADF   copyir.ocm
E602    The HDD has an error   copyir.ocm    
E604-0000    The time memory (DDR-SDRAM) is faulty or inadequate   copyir.ocm
A DDR-SDRAM (1 GB) of adequate capacity is not detected   copyir.ocm    Replace the DDR-SDRAM   copyir.ocm
E609-0008    The HDD temperature is abnormally low   copyir.ocm
At start-up, the HDD does not reach a specific temperature within a specific time   copyir.ocm    Replace the HDD   copyir.ocm
E609-0009    The HDD temperature is abnormally low   copyir.ocm
When returning from sleep mode, the HDD does not reach a specific temperature within a specific time    Replace the HDD   copyir.ocm
E610    The HDD encryption key is faulty   copyir.ocm    
E711-0001    An error has occurred in the communication between the pickup/delivery accessory and the printer unit   copyir.ocm
The communication controller has detected a fault   copyir.ocm    Turn off and then back on the power   copyir.ocm (Turn off the machine and its delivery accessories; then, turn back on all accessories and then the machine   copyir.ocm) Connect the communication cables and terminals between the machine and the delivery accessories once again   copyir.ocm Replace the accessories controller PCB   copyir.ocm Replace the transceiver PCB   copyir.ocm
E712-0001    An error exists in the communication between the ADF and the reader unit   copyir.ocm
As much as 5 sec or more has passed without recovery after communication stopped between the reader controller and the ADF controller   copyir.ocm    Disconnect and then connect the connectors between the reader unit and the ADF   copyir.ocm Replace the reader controller PCB   copyir.ocm Replace the ADF controller PCB   copyir.ocm
E717-0001    An error exists in the communication with the NE controller   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The NE controller that has been connected before power-off is not recognized at power-on   copyir.ocm    Disconnect and then connect the main controller PCB   copyir.ocm Install the NE controller   copyir.ocm Replace the NE controller   copyir.ocm
E717-0002    An error exists in the communication with the NE controller   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
An error that cannot be reset (e   copyir.ocmg   copyir.ocm, cable break) has been detected in the communication   copyir.ocm    Disconnect and then connect the main controller PCB   copyir.ocm Install the NE controller   copyir.ocm Replace the NE controller   copyir.ocm
E719-0001    An error has occurred in the communication with the coin vendor/card reader   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The coin vendor that was connected before power-off is not recognized at power-on   copyir.ocm    Disconnect and then connect the connector of the main controller PCB   copyir.ocm Install the coin vendor   copyir.ocm Replace the coin vendor   copyir.ocm
E719-0002    An error has occurred in the communication with the coin vendor/card reader   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the coin vendor, an error that cannot be reset has occurred (e   copyir.ocmg   copyir.ocm, cable break)    Disconnect and then connect the connector of the main controller PCB   copyir.ocm Install the coin vendor   copyir.ocm Replace the coin vendor   copyir.ocm
E719-0003    An error has occurred in the communication with the coin vendor/card reader   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the coin vendor, a communication error has occurred during acquisition of unit price information   copyir.ocm    Disconnect and then connect the connector of the main controller PCB   copyir.ocm Install the coin vendor   copyir.ocm Replace the coin vendor   copyir.ocm
E719-0011    An error has occurred in the communication with the coin vendor/card reader   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The card reader that was connected before power-off is not recognized at power-on   copyir.ocm    Disconnect and then connect the connector of the main controller PCB   copyir.ocm Install the card reader   copyir.ocm Replace the card reader   copyir.ocm
E719-0012    An error has occurred in the communication with the coin vendor/card reader   copyir.ocm After correcting the fault, be sure to reset the error   copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the card reader, an error that cannot be reset has occurred (e   copyir.ocmg   copyir.ocm, cable break)   copyir.ocm    Disconnect and then connect the connector of the main controller PCB   copyir.ocm Install the card reader   copyir.ocm Replace the card reader   copyir.ocm
E730-1001    A PDL-related error has occurred   copyir.ocm
An initialization error has occurred at the start of a job   copyir.ocm    Reset the PDL mechanism   copyir.ocm Turn off and then on the power   copyir.ocm
E730-100A    A PDL-related error has occurred   copyir.ocm
An error has occurred in the communication with an external controller   copyir.ocm    Reset the PDL mechanism   copyir.ocm Turn off and then on the power   copyir.ocm
E730-9004    A PDL-related error has occurred   copyir.ocm
A fault has been detected in the cable connection with an external controller   copyir.ocm    Turn off and then on the power   copyir.ocm Replace the external controller relay PCB   copyir.ocm Replace the external controller   copyir.ocm
E730-9005    A PDL-related error has occurred   copyir.ocm
A fault has been detected in the cable connection with an external controller   copyir.ocm    Turn off and then on the power   copyir.ocm Replace the external controller relay PCB   copyir.ocm Replace the external controller   copyir.ocm
E730-A006    A PDL-related error has occurred   copyir.ocm
The PDL mechanism does not respond   copyir.ocm    Reset the PDL mechanism   copyir.ocm Turn off and then on the power   copyir.ocm Reinstall the system software   copyir.ocm Replace the main controller   copyir.ocm
E730-A007    A PDL-related error has occurred   copyir.ocm
At start-up, the version of the machine control software and that of the PDL control software do not match   copyir.ocm    Reset the PDL mechanism   copyir.ocm Turn off and then on the power   copyir.ocm Reinstall the system software   copyir.ocm Replace the main controller   copyir.ocm
E730-B013    A PDL-related error has occurred   copyir.ocm
The font data is corrupted at start-up   copyir.ocm    Turn off and then on the power   copyir.ocm Reinstall the system software   copyir.ocm Execute full formatting of the HDD, and reinstall the system software   copyir.ocm
E732-0001    An error has occurred in the communication between the reader unit and the main controller   copyir.ocm
An error has occurred in the communication between the reader unit and the main controller   copyir.ocm    Disconnect and connect the connectors of the read communication cable   copyir.ocm Check the power supply of the reader unit (to see if initialization occurs at power-on)   copyir.ocm Replace the reader controller PCB   copyir.ocm Reap the reader I/F PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E732-0010    An error has occurred in the communication between the reader unit and the main controller   copyir.ocm
A fault has been detected in the reader sync signal detection mechanism   copyir.ocm    Disconnect and connect the connectors of the read communication cable   copyir.ocm Check the power supply of the reader unit (to see if initialization occurs at power-on)   copyir.ocm Replace the reader controller PCB   copyir.ocm Reap the reader I/F PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E733-0000    An error has occurred in the communication between the reader unit and the main controller   copyir.ocm
An error has occurred in the communication between the reader unit and the main controller   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up)   copyir.ocm Replace the DC controller PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E733-0001    An error has occurred in the communication between the reader unit and the main controller   copyir.ocm
An attempt to communicate with the DC controller fails    Disconnect and then connect the connector   copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up)   copyir.ocm Replace the DC controller PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E733-0010    An error has occurred in the communication between the reader unit and the main controller   copyir.ocm
A fault has occurred in the printer engine sync signal detection mechanism   copyir.ocm    Disconnect and then connect the connector   copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up)   copyir.ocm Replace the DC controller PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E740-0002    An error exists in the LAN controller   copyir.ocm
An illegal MAC address has been detected at start-up   copyir.ocm    Replace the main controller PCB   copyir.ocm
E743-0000    A fault exists in the communication between the main controller and the reader controller   copyir.ocm
The reader controller has detected an error in the communication between the main controller and the reader controller   copyir.ocm    Disconnect and then connect the connectors of the reader communications cable   copyir.ocm Replace the reader controller PCB   copyir.ocm Replace the main controller PCB   copyir.ocm
E744-0001    An error exists in the language file/boot ROM   copyir.ocm
The version of the language file on the HDD and that of bootable do not match   copyir.ocm    Update the version of the language file (Language), or install the appropriate file   copyir.ocm
E744-0002    An error exists in the language file/boot ROM   copyir.ocm
The language file on the HDD is too large   copyir.ocm    Update the version of the language file (Language), or install the appropriate file   copyir.ocm
E744-0003    An error exists in the language file/boot ROM   copyir.ocm
There is no language to which a switchover is made as described in the Config file on the HDD   copyir.ocm    Update the version of the language file (Language), or install the appropriate file   copyir.ocm
E744-0004    An error exists in the language file/boot ROM   copyir.ocm
An attempt to switch over to the language described in the Config file on the HDD fails   copyir.ocm    Update the version of the language file (Language), or install the appropriate file   copyir.ocm
E744-1000    An error exists in the language file/boot ROM   copyir.ocm
The connected boot ROM is not one designed for the model in question   copyir.ocm    Replace the boot ROM   copyir.ocm
E744-2000    An error exists in the language file/boot ROM   copyir.ocm
An illegal engine ID has been detected   copyir.ocm    Reinstall the system software   copyir.ocm
E746-0003    An unsupported optional board has been detected   copyir.ocm
The option board that has been detected is one deigned for a different model   copyir.ocm    Replace it with one for the model in question   copyir.ocm
E749-0001    Restart in accordance with a change of the product configuration
A boot ROM designed for a different model has been fitted in place (as when installing an PDL option)   copyir.ocm    There is no need for remedial action   copyir.ocm Nevertheless, the fact will remain as part of the error history   copyir.ocm
E800    The auto power-off circuit has an error   copyir.ocm
An open circuit has been detected for 3 sec or more in the auto power-off circuit   copyir.ocm    Turn off and then on the power   copyir.ocm Disconnect and then connect J505 of the DC controller PCB   copyir.ocm Disconnect and then connect J1719 of the relay PCB   copyir.ocm Replace the relay PCB   copyir.ocm Replace the DC controller PCB   copyir.ocm
E804-0001    The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan   copyir.ocm
The fan stop signal has been detected for 5 sec or more after the power supply cooling fan 1 has gone on   copyir.ocm    Disconnect and then connect J505 of the DC controller PCB   copyir.ocm Replace the power supply cooling fan 1   copyir.ocm Replace the DC controller PCB   copyir.ocm
E804-0002    The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan   copyir.ocm
The fan stop signal has been detected for 5 sec or more after the power supply cooling fan 2 has gone on   copyir.ocm    Disconnect and then connect J505 of the DC controller PCB   copyir.ocm Replace the power supply cooling fan 2   copyir.ocm Replace the DC controller PCB   copyir.ocm
E804-0004    The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan   copyir.ocm
The fan stop signal of the controller cooling fan has been detected continuously for 16 sec   copyir.ocm    Disconnect and then connect J1028 of the main controller PCB   copyir.ocm Replace the controller cooling fan   copyir.ocm Replace the main controller PCB   copyir.ocm
E805-0002    The fixing heat discharge fan rotation is faulty   copyir.ocm
The fan stop signal has been detected for 5 sec or more after the fixing heat discharge fan has gone on   copyir.ocm    Disconnect and then connect J503 of the DC controller PCB   copyir.ocm Replace the fixing heat discharge fan   copyir.ocm Replace the DC controller PCB   copyir.ocm
E820-0000    The drum fan rotation is faulty   copyir.ocm
The fan stop signal has been detected for 5 sec or more after the drum fan has gone on   copyir.ocm    Disconnect and then connect J512 of the DC controller PCB   copyir.ocm Replace the drum fan   copyir.ocm Replace the DC controller PCB   copyir.ocm
E823-0000    The pre-transfer charging assembly fan rotation is faulty   copyir.ocm
The fan stop signal has been detected for 5 sec or more after the pre-transfer charging assembly fan has gone on   copyir.ocmulty   copyir.ocm    Disconnect and then connect J504 of the DC controller PCB   copyir.ocm Replace the pre-transfer charging assembly fan   copyir.ocm Replace the DC controller PCB   copyir.ocm
E840-0000    An HP detection error has occurred in relation to the fixing inlet sensor (fixing wrap jam detection)   copyir.ocm
The home position is not detected when he sensor is moved up/down (i   copyir.ocme   copyir.ocm, the sensor has not gone on)   copyir.ocm    Disconnect and then connect J508, J552, and J553 of the DC controller PCB   copyir.ocm Disconnect and then connect J4001 and J4002 of the fixing inlet sensor ascent/descent motor driver PCB; as necessary, replace the fixing inlet sensor ascent/ descent motor   copyir.ocm Replace the fixing inlet sensor ascent/descent motor driver PCB   copyir.ocm
E840-0001    An HP detection error has occurred in relation to the fixing inlet sensor (fixing wrap jam detection)   copyir.ocm
The home position is not detected when the sensor is moved up/down (i   copyir.ocme   copyir.ocm, the sensor has not gone off)   copyir.ocm    Disconnect and then connect J508, J552, and J553 of the DC controller PCB   copyir.ocm Disconnect and then connect J4001 and J4002 of the fixing inlet sensor ascent/descent motor driver PCB; as necessary, replace the fixing inlet sensor ascent/ descent motor   copyir.ocm Replace the fixing inlet sensor ascent/descent motor driver PCB   copyir.ocm
E850-    There is a fault in the double-feeding detection unit   copyir.ocm
The double-feeding sensor (reception) fails to attain an ultrasonic signal of a specific level   copyir.ocm    Remove paper lint form the surface of the double-feeding sensor (reception)   copyir.ocm Remount the double-feeding sensor (transmission, reception)   copyir.ocm Disconnect and then connect J509 and J550 of the DC controller PCB   copyir.ocm Replace the double-feeding sensor (transmission, reception)   copyir.ocm Replace the double-feeding sensor PCB (transmission, reception)   copyir.ocm

 

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب