Your browser does not support JavaScript! > کانون پلاس +Canon iR105

   کانال تلگرام کپی ایران

(0) محصول
یکشنبه, 09 اسفند 1394 11:55

کانون پلاس +Canon iR105

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-0000    The temperature of the fixing assembly is abnormally high  copyir.com
When the main power switch is turned on, the reading of the main thermistor does not reach 70 deg C within 3 min 30 sec  copyir.com    - Check if the main thermistor is mounted properly and also check if there is no contamination  copyir.com - Replace the main thermistor  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E000-0010    The temperature of the fixing assembly is abnormally high  copyir.com
The power is turned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E001-0001    The over-rising in temperature of the fixing assembly is detected  copyir.com
The hardware port detects a fault  copyir.com    - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E001-0002    The over-rising in temperature of the fixing assembly is detected  copyir.com
Either the main thermistor or the sub thermistor detects 230 deg C or higher for 2 sec  copyir.com    - Check if the main thermistor and the sub thermistor are mounted properly  copyir.com - Replace the main thermistor or the sub thermistor  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E001-0003    The over-rising in temperature of the fixing assembly is detected  copyir.com
The reading of the main thermistor is higher than that of the sub thermistor by 50 deg C or more for 1 sec  copyir.com    Check if the main thermistor and the sub thermistor are mounted properly  copyir.com - Replace the main thermistor  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E001-0004    The over-rising in temperature of the fixing assembly is detected  copyir.com
The reading of the main thermistor is lower than that of the sub thermistor by 50 deg C or more for 1 sec  copyir.com    - Check if the main thermistor is mounted properly  copyir.com - Replace the main thermistor  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E001-0010    The over-rising in temperature of the fixing assembly is detected  copyir.com
The power is turned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E002-0000    The rise in temperature of the fixing assembly is faulty  copyir.com
The reading of the main thermistor (TH1فتوکپی کانون  does not reach 100 deg C 2 min 30 sec after it has exceeded 70 deg C  copyir.com    - Check if the connector (J505فتوکپی کانون  of the DC controller PCB is mounted properly and also check if the connector of the fixing assembly is mounted properly  copyir.com - Check the wiring between the thermistor and the DC controller  copyir.com -Check if the main thermistor is mounted properly and also check if there is no contamination  copyir.com - Replace the main thermistor  copyir.com - Replace the fixing heater  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E002-0001    The rise in temperature of the fixing assembly is faulty  copyir.com
The reading of the main thermistor does not reach 150 deg C within 2 min 30 sec after it has exceeded 100 deg C  copyir.com    - Check if the connector (J505فتوکپی کانون  of the DC controller PCB is mounted properly and also check if the connector of the fixing assembly is mounted properly  copyir.com - Check the wiring between the thermistor and the DC controller  copyir.com -Check if the main thermistor is mounted properly and also check if there is no contamination  copyir.com - Replace the main thermistor  copyir.com - Replace the fixing heater  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E002-0010    The rise in temperature of the fixing assembly is faulty  copyir.com
The power has been turned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E003-0000    The fixing temperature is too low after a standby state  copyir.com
The reading of the main thermistor is 70 deg C or lower for 2 sec or more after it has reached 100 deg C  copyir.com    - Check if the connector (J505فتوکپی کانون  of the DC controller PCB is mounted properly and also check if the connector of the fixing assembly is mounted properly  copyir.com - Check the wiring between the thermistor and the DC controller  copyir.com -Check if the main thermistor is mounted properly and also check if there is no contamination  copyir.com - Replace the main thermistor  copyir.com - Replace the fixing heater  copyir.com - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E003-0010    The fixing temperature is too low after a standby state  copyir.com
The power has been turned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E004-0000    The fixing assembly is faulty  copyir.com
The SSR used to drive the fixing heater has a short circuit (detection by hardware circuitryفتوکپی کانون   copyir.com    - Replace the AC driver PCB  copyir.com - Replace the DC controller PCB  copyir.com Caution You will have to clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E005-0000    The absence of the fixing web is detected  copyir.com
The length of the fixing web that has been taken up is more than a specific value and the fixing web length sensor (PS7فتوکپی کانون  has detected the absence of the web for 5 sec or more  copyir.com    - Check the position of the fixing web detection lever  copyir.com - Replace the fixing web  copyir.com - Replace the fixing web length sensor  copyir.com - Replace the DC controller PCB  copyir.com Caution After replacing the fixing web, you will have to clear the two web counters in service mode (COPIER>COUNTER>MISC>FIX-WEB and COPIER>COUNTER>DRBL-1>FIX-WEBفتوکپی کانون   copyir.com
E005-0010    The absence of the fixing web is detected  copyir.com
The power is turned off and then on without clearing the error  copyir.com    - Reset the counters of the two webs to zero in service mode (COPIER>COUNTER>MISC>FIX-WEB, COPIER>COUNTER>DRBL-1>FIX-WEBفتوکپی کانون
E010-0000    The rotation of the main motor is faulty  copyir.com
No clock pulse arrive for 2 sec or more after the main motor drive signal (MMFGفتوکپی کانون  has been generated  copyir.com    - Check if the connecter (J611, J612فتوکپی کانون  of the main motor is mounted properly  copyir.com - Check if the connector (J1720فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the main motor  copyir.com - Replace the relay PCB  copyir.com - Replace the DC controller PCB  copyir.com
E012-0000    The rotation of the drum motor is faulty  copyir.com
No clock pulse arrives for 2 sec or more after the drum motor drive signal (DMFGفتوکپی کانون  has been generated  copyir.com    - Check if the connector (J1720فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Check if the connector (J512فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Check if the connecter (J601, J602فتوکپی کانون  of the drum motor is mounted properly  copyir.com - Replace the drum motor  copyir.com - Replace the DC controller PCB  copyir.com
E013-0000    The lock of the waste toner feed screw is detected  copyir.com
The waste toner feed screw fails to rotate normally, and the switch MSW2 is pressed multiple times within a specific period of time  copyir.com    - Re-mount the waste toner pipe  copyir.com - Replace the waste toner pipe  copyir.com - Replace the waste toner clog detecting switch  copyir.com - Replace the DC controller PCB  copyir.com Caution You will have to clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E013-0010    The lock of the waste toner feed screw is detected  copyir.com
The power is tuned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E014-0000    The rotation of the fixing motor is faulty  copyir.com
The motor clock signal is not detected for 2 sec or more after the fixing motor drive signal has been generated  copyir.com    - Check if the connecter (J651, J652فتوکپی کانون  of the fixing motor is mounted properly  copyir.com - Replace the fixing motor  copyir.com - Replace the relay PCB  copyir.com - Replace the DC controller PCB  copyir.com
E015-0000    The rotation of the pickup motor is faulty  copyir.com
The motor lock signal is not detected for 2 sec or more after the pickup motor drive signal has been generated  copyir.com    - Check if the connecter (J621, J622فتوکپی کانون  of the pickup motor is mounted properly  copyir.com - Replace the pickup motor  copyir.com - Replace the relay PCB  copyir.com - Replace the DC controller PCB  copyir.com
E019-0000    The waste toner case is full, or the waste toner case full sensor is faulty  copyir.com
More than a specific number of pages are printed without disposing of the waste toner after the waste toner case has been found to be full  copyir.com    - Dispose the waste toner in the case  copyir.com - Check the operation of the base plate of waste toner case  copyir.com - Check if the connector (J514فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the waste toner full sensor  copyir.com - Replace the DC controller PCB  copyir.com
E020-0000    The difficulty providing toner inside the hopper developing assemblies is detected  copyir.com
Although the developing assembly is supplied with toner, the absence of toner inside it is detected for 3 sec or more  copyir.com    - Replace the magnet roller drive clutch  copyir.com - Replace the toner feed motor (M18فتوکپی کانون   copyir.com - Replace the toner sensor  copyir.com Caution You will have to clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E020-0010    The difficulty providing toner inside the hopper developing assemblies is detected  copyir.com
The power is turned off and then on without clearing the error  copyir.com    - Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERRفتوکپی کانون   copyir.com
E025-0000    The toner feed motor inside the hopper is faulty  copyir.com
The DC controller PCB detects an overcurrent flowing to the toner feed motor (M6فتوکپی کانون  inside the cartridge for 10 sec or more twice  copyir.com (In response to the first detection, it indicates the message "Shake the Toner Case, and Set  copyir.com"فتوکپی کانون     - Check if the connector (J512فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the toner feed motor (M6فتوکپی کانون   copyir.com
E032-0000    The counter of the copy data controller or the NE controller is faulty  copyir.com
The copy data controller or the NE controller are disconnected after they have once been connected  copyir.com    - Check if the connecter of the main controller PCB is mounted properly  copyir.com - Replace the main controller PCB  copyir.com - Replace the copy data controller or the NE controller  copyir.com
E043-0000    The rotation of the side paper deck main motor is faulty  copyir.com
The PLL lock signal (DMPLKفتوکپی کانون  does not arrive for 2 sec or more after the side paper deck main motor drive signal has been generated  copyir.com    - Check if the connecter (J101, J106فتوکپی کانون  of the side deck driver PCB is mounted properly  copyir.com - Replace the side deck main motor  copyir.com - Replace the side deck driver PCB  copyir.com - Replace the DC controller PCB  copyir.com
E051-0001    There is an error in the detection of the horizontal registration home position  copyir.com
Departure from home position is not detected within 5 sec during a horizontal registration home position search  copyir.com    - Replace the horizontal registration sensor  copyir.com - Replace the horizontal registration motor  copyir.com - Check if the manual feed tray open/closed detecting switch is mounted properly  copyir.com - Replace the stackless feed driver PCB  copyir.com - Replace the DC controller PCB  copyir.com
E051-0002    There is an error in the detection of the horizontal registration home position  copyir.com
Home position is not detected within 5 sec during a horizontal registration home position search  copyir.com    - Replace the horizontal registration sensor  copyir.com - Replace the horizontal registration motor  copyir.com - Check if the manual feed tray open/closed detecting switch is mounted properly  copyir.com - Replace the stackless feed driver PCB  copyir.com - Replace the DC controller PCB  copyir.com
E051-0003    There is an error in the detection of the horizontal registration home position  copyir.com
The horizontal registration detection movement for the preceding sheet does not end within 5 sec at the start of a horizontal registration search during printing  copyir.com    - Replace the horizontal registration sensor  copyir.com - Replace the horizontal registration motor  copyir.com - Check if the manual feed tray open/closed detecting switch is mounted properly  copyir.com - Replace the stackless feed driver PCB  copyir.com - Replace the DC controller PCB  copyir.com?
E065-0000    There is an error in the high-voltage output to the transfer charging assembly  copyir.com
An error (leakageفتوکپی کانون  is detected in the high-voltage output to the primary charging assembly  copyir.com    - Check if the primary charging assembly is mounted properly and also check if there is no contamination  copyir.com - Check if the connector (T601, J723, J730فتوکپی کانون  of the HV-DC PCB is mounted properly and also check the wiring  copyir.com - Replace the HV-DC PCB  copyir.com
E067-0000    There is an error in the high-voltage output  copyir.com
An error is detected in two or more of the following at the same time: the primary high voltage, pre-transfer high voltage, transfer high voltage, and separation high voltage  copyir.com Or, an error (leakageفتوکپی کانون  in the high-voltage output to the separation charging assembly is detected  copyir.com    - Check if the primary charging assembly, pretransfer charging assembly, transfer charging assembly and separation charging assembly are mounted properly  copyir.com - Check if the connector (J722, J723, J730فتوکپی کانون  of the HV-DC PCB is mounted properly and also check the wiring  copyir.com - Replace the HV-DC PCB  copyir.com - Replace the HV-AC PCB  copyir.com
E068-0000    There is an error in the high-voltage output to the separation charging assembly  copyir.com
An error (leakageفتوکپی کانون  to the high-voltage output to the separation charging assembly is detected  copyir.com    - Check if the transfer charging assembly and separation charging assembly are mounted properly  copyir.com - Check if the connector (J722, J723, J730, J734فتوکپی کانون  of the HV-DC PCB and the connector (J741, J742فتوکپی کانون  of the HV-AC PCB are mounted properly  copyir.com - Replace the HV-AC PCB  copyir.com - Replace the separation charging assembly  copyir.com - Replace the pre-transfer charging assembly  copyir.com
E069-0000    There is an error in the high-voltage output to the transfer charging assembly  copyir.com
An error (leakageفتوکپی کانون  is detected in the high-voltage output to the transfer charging assembly  copyir.com    - Check if the transfer charging assembly and separation charging assembly are mounted properly  copyir.com - Check if the connector (T701, J723, J730فتوکپی کانون  of the HV-DC PCB is mounted properly and also check the wiring  copyir.com - Replace the HV-DC PCB  copyir.com - Replace the pre-transfer charging assembly  copyir.com
E100-0000    The BD PCB is faulty  copyir.com
The BD signal does not arrive within 1 sec after the laser drive signal has been generated  copyir.com Or, the BD signal does not arrive for 1 sec or more while the laser remains ON  copyir.com    - Check if the BD PCB, laser driver PCB and DC controller are connected properly  copyir.com - Replace the BD PCB  copyir.com - Replace the laser scanner unit  copyir.com - Replace the DC controller PCB  copyir.com
E110-0000    The rotation of the laser scanner motor is faulty  copyir.com
The constant speed rotation signal (LM-RDYفتوکپی کانون  does not arrive for 20 sec or more after the laser scanner motor (M4فتوکپی کانون  drive signal has been generated  copyir.com    - Check if the connector (J762فتوکپی کانون  of the laser scanner motor driver PCB is mounted properly  copyir.com - Check if the connector (J503فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the laser scanner unit  copyir.com - Replace the DC controller PCB  copyir.com
E111-0000    The rotation of the laser motor cooling fan is faulty  copyir.com
The lock signal arrives for 5 sec or more although the laser motor cooling fan (FM1فتوکپی کانون  is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the laser motor cooling fan  copyir.com - Check if the connector (J503فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the laser motor cooling fan  copyir.com - Replace the DC controller PCB  copyir.com
E121-0001    The rotation of the laser cooling fan (1/2فتوکپی کانون  is faulty  copyir.com
The lock signal arrives for 5 sec or more although the laser cooling fan 1 (FM3فتوکپی کانون  is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the laser cooling fan 1  copyir.com - Check if the connector (J503فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the laser cooling fan 1  copyir.com - Replace the DC controller PCB  copyir.com
E121-0002    The rotation of the laser cooling fan (1/2فتوکپی کانون  is faulty  copyir.com
The lock signal arrives for 5 sec or more although the laser cooling fan 2 (FM5فتوکپی کانون  is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the laser cooling fan 2  copyir.com - Check if the connector (J503فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the laser cooling fan 2  copyir.com - Replace the DC controller PCB  copyir.com
E202-0000    There is an error in the detection of the scanner home position  copyir.com
Scanner home position cannot be detected within a specific period of time after the power switch is turned on or the Start key is pressed  copyir.com    Caution No code will be indicated  copyir.com The keys will be locked  copyir.com You can check the code in service mode (COPIER>DISPLAY>ERRفتوکپی کانون   copyir.com - Check if the scanner motor is connected properly, and replace the scanner motor if necessary  copyir.com - Check if the connector (J1720فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the scanner home position sensor  copyir.com - Replace the reader controller PCB  copyir.com
E204-0000    There is an error in the detection of the image leading edge signal  copyir.com
During forward movement in fixed reading mode or during a home position search, the image leading signal does not occur; or, in stream reading mode, the image leading edge signal does not arrive from the ADF controller PCB  copyir.com    Caution No code will be indicated  copyir.com The keys will be locked  copyir.com You can check the code in service mode (COPIER>DISPLAY>ERRفتوکپی کانون   copyir.com - Check if the scanner motor is connected properly, and replace the scanner motor if necessary  copyir.com - Replace the scanner image leading edge sensor  copyir.com - Replace the reader controller PCB  copyir.com
E211-0000    The rise in temperature of the scanning lamp heater is faulty  copyir.com
While the power is ON, the ambient temperature of the scanning lamp does not exceed 10 deg C 2 min after the florescent heater has gone ON; or, after the power is turned on, the reading of the ambient temperature of the scanning lamp is 0 deg C or lower  copyir.com    - Check if the connecter (J852, J853فتوکپی کانون  of the light control PCB is mounted properly  copyir.com - Replace the scanning lamp heater  copyir.com - Replace the light control PCB  copyir.com - Replace the reader controller PCB  copyir.com
E215-0000    The rise in temperature of the scanning lamp heater is faulty  copyir.com
While the scanning lamp is OFF, the reading of the ambient temperature is 170 deg C or higher  copyir.com    - Check if the connecter (J852, J853فتوکپی کانون  of the light control PCB is mounted properly  copyir.com - Replace the scanning lamp heater  copyir.com - Replace the light control PCB  copyir.com - Replace the reader controller PCB  copyir.com
E218-0000    The scanning lamp is not mounted properly  copyir.com
When the power is turned on, the absence of the scanning lamp is detected  copyir.com    - Check if the scannning lamp is mounted properly  copyir.com - Check if the connecter (J1002, J1003فتوکپی کانون  of the inverter PCB is mounted properly  copyir.com - Check if the connector (J1720فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the scanning lamp  copyir.com - Replace the reader controller PCB  copyir.com
E219-0000    The scanning lamp life
While the scanning lamp is ON, the reading of the ambient temperature is 170 deg C or higher  copyir.com    - Check if the connecter (J852, J853فتوکپی کانون  of the light control PCB is mounted properly  copyir.com - Replace the scanning lamp heater  copyir.com - Replace the light control PCB  copyir.com - Replace the reader controller PCB  copyir.com
E220-0000    The lighting of the scanning lamp is faulty  copyir.com
The scanning lamp does not reach a specific intensity within 10 sec after it is tuned on (if the room temperature is 10 deg C or lower, within 60 secفتوکپی کانون   copyir.com Or, the ON detection signal (FL-DTCTفتوکپی کانون  does not go OFF within 5 sec after the scanning lamp is turned off; during shading adjustment, the ON detection signal (FL-DTCTفتوکپی کانون  does not go ON within 60 sec after the scanning lamp is turned on  copyir.com    - Check if the connecter (J852, J853فتوکپی کانون  of the light control PCB is mounted properly  copyir.com - Replace the scanning lamp heater  copyir.com - Replace the light control PCB  copyir.com - Replace the reader controller PCB  copyir.com
E222-0000    The rise in temperature of the scanning lamp heater is faulty  copyir.com
During the initial activation after power-on, the reading does not reach 70 deg C within 5 min after the heater is turned on  copyir.com Or, during standby or reading operation, the reading does not reach 75 deg C within 3 min after the heater is tuned on  copyir.com    - Check if the connecter (J852, J853فتوکپی کانون  of the light control PCB is mounted properly  copyir.com - Replace the scanning lamp heater  copyir.com - Replace the light control PCB  copyir.com - Replace the reader controller PCB  copyir.com
E240-0000    The communication between the MCON and DCON is faulty  copyir.com
A communication fault exists between the CPUs of the main controller PCB and the DC controller PCB  copyir.com    - Check the wiring between the DC controller PCB and the main controller PCB  copyir.com - Replace the DC controller PCB  copyir.com - Replace the main controller PCB  copyir.com
E241-0000    The communication between the original orientation detection PCB and RCON is faulty  copyir.com
The initial communication between the CPUs of the original orientation detection PCB and the reader controller PCB fails  copyir.com    - Replace the original orientation PCB  copyir.com - Replace the reader controller PCB  copyir.com
E241-0001    The communication between the original orientation detection PCB and RCON is faulty  copyir.com
When the orientation of an original is detected, the result of detection is not communicated by the original orientation detection PCB until the next original is read  copyir.com    - Replace the original orientation PCB  copyir.com - Replace the reader controller PCB  copyir.com
E241-0002    The communication between the original orientation detection PCB and RCON is faulty  copyir.com
The result of detection of the last original is not communicated 5 sec after the end of reading the last original  copyir.com    - Replace the original orientation PCB  copyir.com - Replace the reader controller PCB  copyir.com
E243-0000    The communication between the control panel PCB and MCON is faulty  copyir.com
A communication fault exists between the CPUs of the control panel PCB and the main controller PCB  copyir.com    - Replace the control panel PCB  copyir.com - Replace the main controller PCB  copyir.com
E251-0000    The rotation of the inverter cooling fan is faulty  copyir.com
The lock signal (FM9LCKفتوکپی کانون  arrives for 5 sec or more although the inverter cooling fan (FM9فتوکپی کانون  is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the inverter cooling fan  copyir.com - Check if the connecter (J1110فتوکپی کانون  of the reader control PCB is mounted properly  copyir.com - Replace the inverter cooling fan  copyir.com - Replace the reader controller PCB  copyir.com
E302-0000    Shading error
During shading operation, the reader controller PCB fails to end shading processing  copyir.com    - Check if the connecter (J1502, J1503فتوکپی کانون  of the CCD PCB is mounted properly  copyir.com - Check if the connecter (J1107, J1108فتوکپی کانون  of the reader control PCB is mounted properly  copyir.com - Replace the CCD PCB  copyir.com - Replace the reader controller PCB  copyir.com
E315-0000    There is an error in image data  copyir.com The reader controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
During image rotation, the encoding/ decoding has a fault  copyir.com    - Replace the reader controller PCB  copyir.com - Replace the main controller PCB  copyir.com
E320-0000    There is a time out error in the image reading processing  copyir.com
While an image is being read, the image read end notice does not arrive at the reader controller PCB within 60 sec from the CCD/AP PCB  copyir.com    - Check if the connecter (J1502, J1503فتوکپی کانون  of the CCD PCB is mounted properly  copyir.com - Check if the connecter (J1107, J1108فتوکپی کانون  of the reader control PCB is mounted properly  copyir.com - Replace the CCD PCB  copyir.com - Replace the reader controller PCB  copyir.com
E400-0000    Communication error with the ADF
While the ADF is in standby, the communication between ADF and copier is interrupted for 5 sec or more  copyir.com Or, when the ADF is in operation, the communication between ADF and copier is disrupted for 0  copyir.com5 sec or more  copyir.com    - Check if the communication cable between the ADF and copier is connected properly  copyir.com - Replace the ADF controller PCB  copyir.com
E402-0000    The rotation of the ADF belt motor is faulty  copyir.com
The clock signal does not occur for 100 msec when the belt motor drive signal is generated  copyir.com    - Check if the cable between the ADF belt motor drive PCB and ADF controller PCB is connected properly  copyir.com - Replace the ADF belt motor clock sensor  copyir.com - Replace the ADF belt motor  copyir.com - Replace the ADF belt motor drive PCB  copyir.com - Replace the ADF controller PCB  copyir.com
E404-0000    The rotation of the ADF delivery motor is faulty  copyir.com
The clock signal does not occur for 200 msec when the delivery motor drive signal is generated  copyir.com    - Replace the ADF delivery motor  copyir.com - Replace the ADF delivery motor clock sensor  copyir.com - Replace the ADF controller PCB  copyir.com
E405-0000    The rotation of the ADF separation motor is faulty  copyir.com
The clock signal does not occur for 200 msec when the separation motor drive signal is generated  copyir.com    - Replace the ADF separation motor  copyir.com - Replace the ADF separation motor clock sensor  copyir.com - Replace the ADF controller PCB  copyir.com
E410-0000    The rotation of the ADF pickup motor is faulty  copyir.com
The pickup roller height sensor 1 (PI8فتوکپی کانون  or 2 (PI9فتوکپی کانون  does not generate a signal within 2 sec after the pickup motor is driven  copyir.com Or, the pickup roller home position sensor (PI7فتوکپی کانون  does not generate a signal within 2 sec after the pickup motor is driven  copyir.com    - Replace the ADF pickup motor  copyir.com - Replace the ADF pickup roller height sensor 1  copyir.com - Replace the ADF pickup roller height sensor 2  copyir.com - Replace the ADF pickup roller home position sensor  copyir.com - Replace the ADF controller PCB  copyir.com
E412-0000    The rotation of the ADF cooling fan is faulty  copyir.com
The lock signal arrives for 100 msec or more although the cooling fan is being driven  copyir.com    - Replace the ADF cooling fan  copyir.com - Replace the ADF controller PCB  copyir.com
E420-0000    The EEPROM is faulty  copyir.com The ADF controller PCB is faulty  copyir.com
The backup data of the EEPROM cannot be read when the connected device is tuned on  copyir.com Or, the data that has been read has a fault  copyir.com    - Replace the ADF controller PCB  copyir.com
E602    There is an error on the hard disk  copyir.com    
E604-0000    The image memory is faulty or is inadequate  copyir.com
The memory size does not match the model  copyir.com    - Increase the memory  copyir.com
E609-0008    There is an error on the HDD  copyir.com
At startup, the HDD fails to reach a specific temperature level within a specific period of time  copyir.com    - Replace the HDD  copyir.com - Replace the DC controller PCB  copyir.com
E609-0009    There is an error on the HDD  copyir.com
At time of sleep recovery, the temperature fails to reach a specific level  copyir.com    - Replace the HDD  copyir.com - Replace the DC controller PCB  copyir.com
E610    The HDD coding key is faulty  copyir.com
The SRAM/PCB is faulty  copyir.com The battery has become exhausted, leading to loss of SRAM contents  copyir.com    - Turn off and then back on the power switch to generate the key once again  copyir.com - Replace the main controller PCB  copyir.com
E710-0001    There is an error in the initialization of the IPC  copyir.com
The IPC (IC5فتوکپی کانون  on the reader controller PCB cannot be initialized when the main power supply is turned on  copyir.com    - Check the cable  copyir.com - Replace the reader controller PCB  copyir.com
E710-0002    There is an error in the initialization of the IPC  copyir.com
The IPC (IC40فتوکپی کانون  on the DC controller PCB cannot be initialized when the main power supply is turned on  copyir.com    - Check the cable  copyir.com - Replace the DC controller PCB  copyir.com
E710-0003    There is an error in the initialization of the IPC  copyir.com
The IPC (IC1003فتوکپی کانون  on the machine controller PCB cannot be initialized when the main power is turned on  copyir.com    - Check the cable  copyir.com - Replace the main controller PCB  copyir.com
E711-0001    There is an error in the IPC communication  copyir.com
Data has been written to the error register of the IPC (IC5فتوکپی کانون  on the reader controller PCB 4 times or more within 1  copyir.com5 sec  copyir.com    - Check the cable  copyir.com - Replace the reader controller PCB  copyir.com
E711-0002    There is an error in the IPC communication  copyir.com
Data has been written to the error register of the IPC (IC40فتوکپی کانون  on the DC controller PCB 4 times or more within 2 sec  copyir.com    - Check the cable  copyir.com - Replace the DC controller PCB  copyir.com
E711-0003    There is an error in the IPC communication  copyir.com
Data has been written to the error register of the IPC (IC1003فتوکپی کانون  on the main controller PCB 4 times or more within 2 sec  copyir.com    - Check the cable  copyir.com - Replace the main controller PCB  copyir.com
E712-0000    Communication error with the ADF
The communication IC (IPCفتوکپی کانون  on the ADF controller PCB goes out of order  copyir.com    - Check if the communication cable between the ADF and copier is connected properly  copyir.com - Replace the ADF controller PCB  copyir.com
E713-0000    There is an error in the communication with the finisher  copyir.com
The communications IC (IPCفتوکپی کانون  on the finisher controller PCB goes out of order  copyir.com    - Check if the communication cable between the finisher and copier is connected properly  copyir.com - Replace the finisher controller PCB  copyir.com - Replace the DC controller PCB  copyir.com
E717-0001    There is an error in the communication with the NE controller  copyir.com
The NE controller is not connected at power on, although it was connected before the power was turned off because of an error  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E717-0002    There is an error in the communication with the NE controller  copyir.com
An IPC error has occurred while the NE controller is in operation  copyir.com There is an open circuit for the IPC  copyir.com An error has occurred, and the IPC communication remains disabled  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E719-0001    There is a coin vendor error  copyir.com
The coin vendor is not connected when the power is turned on, although it was connected before the power was turned off because of an error  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E719-0002    There is a coin vendor error  copyir.com
While the coin vendor is in operation, an IPC error has occurred, IPC has developed an open circuit, or an error preventing recovery of IPC communication has occurred  copyir.com An open circuit ha been detected in the line for the pickup/delivery signal  copyir.com An illegal signal has been detected  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E719-0003    There is a coin vendor error  copyir.com
While the unit price is being checked at startup, an error occurs in the communication with the coin vendor  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E719-0011    There is a coin vendor error  copyir.com
An error has occurred at new card reader startup  copyir.com The new card reader is not connected when the power is turned off, although it was connected when the power was turned off  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E719-0012    There is a coin vendor error  copyir.com
An IPC error has occurred at new card reader startup  copyir.com There is an IPC open circuit  copyir.com An error has occurred that prevents recovery of IPC communication  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR  copyir.com
E730-1001    There is a PDL software error  copyir.com
An initialization error has occurred  copyir.com    - Execute PDL resetting  copyir.com - Turn on the power once again  copyir.com
E730-100A    There is a PDL software error  copyir.com
An error that may be critical to the system (e  copyir.comg  copyir.com, failed initializationفتوکپی کانون  has occurred  copyir.com    - Execute PDL resetting  copyir.com - Turn on the power once again  copyir.com
E730-9004    There is a PDL software error  copyir.com
There is an error in the communication (PAIفتوکپی کانون  with an external controller  copyir.com    - Turn on the power once main  copyir.com - Check the connection of the open I/F board and the cable  copyir.com - Replace the board for the external controller open I/F  copyir.com - Replace the main controller PCB  copyir.com
E730-9005    There is a PDL software error  copyir.com
Fault in the connector of the vide cable to the external controller    - Turn on the power once main  copyir.com - Check the connection of the open I/F board and the cable  copyir.com - Replace the board for the external controller open I/F  copyir.com - Replace the main controller PCB  copyir.com
E730-A006    There is a PDL software error  copyir.com
The PDL board does not respond  copyir.com A subbootable is faulty or absent  copyir.com    - Execute PDL resetting  copyir.com - Turn on the power once again  copyir.com - Check the connection of the UFR board  copyir.com - Re-install the firmware  copyir.com - Replace the main controller PCB  copyir.com
E730-A007    There is a PDL software error  copyir.com
There is a mismatch between the control software of the machine and the PDL control software in regard to version  copyir.com    - Execute PDL resetting  copyir.com - Turn on the power once again  copyir.com - Execute system formatting (allفتوکپی کانون , and reinstall the system  copyir.com
E730-B013    There is a PDL software error  copyir.com
Corruption in the font data    - Turn on the power once again  copyir.com - Re-install the Software  copyir.com - Execute system formatting (allفتوکپی کانون , and reinstall the system  copyir.com
E732-0001    There is an error in the communication with the scanner  copyir.com
There is a DDI-S communication error  copyir.com    - Check the connector used to connected the scanner  copyir.com - Check the power supply of the scanner (to see if initialization takes place at startupفتوکپی کانون   copyir.com - Replace the reader controller, scanner board, or main controller PCB as necessary  copyir.com
E733-0000    There is an error in the communication with the printer  copyir.com
At startup, communication with the printer fails  copyir.com    - Check the connector used to connect to the printer  copyir.com - Check the power supply of the printer (to see if initialization takes place at startupفتوکپی کانون   copyir.com - Replace the DC controller or the main controller PCB  copyir.com
E733-0001    There is an error in the communication with the printer  copyir.com
There is a DDI-P communication error  copyir.com    - Check the connection with the printer  copyir.com - Check the power supply of the printer (to see if initialization takes place at startupفتوکپی کانون   copyir.com - Replace the DC controller or the main controller PCB  copyir.com
E740-0002    There is an error on the Ethernet board  copyir.com
The MAC address is illegal  copyir.com    - Replace the main controller PCB  copyir.com
E744    There is an error in the language file/boot ROM  copyir.com    - Download a language file of the correct version  copyir.com
E745    There is a fault on the TokenRing board    - Disconnect and then connect the TokenRing board  copyir.com - Replace the TokenRing board  copyir.com
E746-0003    The accessories board is of the wrong type  copyir.com
?At startup, a board for a different model has been detected  copyir.com    - Replace the UFR board of the correct type (modelفتوکپی کانون   copyir.com
E748-1001    Mismatch in controller board and SDRAM size?
There is a mismatch between the control board and the SDRAM  copyir.com    - Check the correct combination between main controller PCB and SDRAM  copyir.com
E800-0000    There is an error in the auto power-off circuit  copyir.com
An open circuit is detected in the auto power-off circuit for 3 sec or more  copyir.com    - Turn on the power once again  copyir.com - Check if the connector (J505فتوکپی کانون  of theDC controller PCB is mounted properly  copyir.com - Check if the connector (J1719فتوکپی کانون  of the relay PCB is mounted properly  copyir.com - Replace the relay PCB  copyir.com - Replace the DC controller PCB  copyir.com
E804-0000    There is an error in the system fan/the power supply cooling fan (1 and 2فتوکپی کانون   copyir.com
The lock signal is detected for 5 sec or more although the power supply cooling fan (1 and 2فتوکپی کانون  is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the power supply cooling fan (1 and 2فتوکپی کانون  fan  copyir.com - Check if the connector (J505فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the power supply cooling fan (1/2فتوکپی کانون   copyir.com - Replace the DC controller PCB  copyir.com
E804-0004    There is an error in the system fan/the power supply cooling fan (1 and 2فتوکپی کانون   copyir.com
The reading of the ambient temperature of the main controller is 80 degrees or higher  copyir.com    - Check if there is no foreign material in the rotation assembly of the system fan  copyir.com - Check if the connector (J1028فتوکپی کانون  of the main controller PCB is mounted properly  copyir.com - Replace the sysytem fan  copyir.com - Replace the main controller PCB  copyir.com Caution In the case of a fault in the system fan, the data will be indicated in the form of an alarm (0008040004; ALARM-2فتوکپی کانون   copyir.com
E805-0001    The rotation of the fixing assembly heat discharging fan and separation heat discharging fan is faulty  copyir.com
The lock signal is detected for 5 sec or more although the fixing assembly heat discharging fan is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the fixing assembly heat discharging fan  copyir.com - Check if the connector (J503فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the fixing assembly heat discharging fan  copyir.com - Replace the DC controller PCB  copyir.com
E805-0002    The rotation of the fixing assembly heat discharging fan and separation heat discharging fan is faulty  copyir.com
The lock signal is detected for 5 sec or more although the separation heat discharging fan is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the separation heat discharging fan  copyir.com - Check if the connector (J1112فتوکپی کانون  of the reader controller PCB is mounted properly  copyir.com - Replace the separation heat discharging fan  copyir.com - Replace the reader controller PCB  copyir.com
E820-0000    The rotation of the drum fan is faulty  copyir.com
The lock signal is detected for 5 sec or more although the drum fan is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the drum fan  copyir.com - Check if the connector (J512فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the drum fan  copyir.com - Replace the DC controller PCB  copyir.com
E823-0000    The rotation of the pre-transfer charging assembly fan is faulty  copyir.com
The lock signal is detected for 5 sec or more although the pre-transfer charging assembly fan is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the pre-transfer charging assembly fan  copyir.com - Check if the connector (J504فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the pre-transfer charging assembly fan  copyir.com - Replace the DC controller PCB  copyir.com
E830-0000    The rotation of the separation fan is faulty  copyir.com
The lock signal is detected for 5 sec or more although the separation cooling fan is being driven  copyir.com    - Check if there is no foreign material in the rotation assembly of the separation cooling fan  copyir.com - Check if the connector (J509فتوکپی کانون  of the DC controller PCB is mounted properly  copyir.com - Replace the separation cooling fan  copyir.com - Replace the DC controller PCB  copyir.com

خواندن 1283 دفعه
محتوای بیشتر در این بخش: « کانون Canon iR105 کانون Canon iR1210 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب