Your browser does not support JavaScript! > کانون Canon CP2120

   کانال تلگرام کپی ایران

(0) محصول
جمعه, 07 اسفند 1394 17:08

کانون Canon CP2120

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای زیراکس   براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

 

E000-0021    Within a temperature range of 50°C or lower as detected by the thermistor (TH1), the increase in temperature in 1 min is less than 3°C  copyir.com    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-0031    Within a temperature range between 50°C and 190°C as detected by the thermistor, the increase in temperature within 30 sec is less than 5°C  copyir.com    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-0040    During standby, the fixing temperature has dropped below 140°C  copyir.com    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-0050    During printing, the fixing temperature has dropped below 140°C  copyir.com    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-01    Main thermistor (TH1)    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-02    Sub thermistor (TH2)    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E000-03    The thermistor (TH1, TH2) has detected an open circuit  copyir.com    The fixing heater is faulty  copyir.com The SSR is faulty  copyir.com The fixing thermistor is faulty  copyir.com The thermistor (TH1, TH2) has an open circuit  copyir.com The thermal switch (TP1) has turned on  copyir.com
E004-01    Main heater (H1)
SSR1 for the fixing heater is ON even though the fixing heater (H1, H2) is OFF  copyir.com    The SSR1 is faulty  copyir.com
E004-02    Sub heater (H2)
SSR1 for the fixing heater is ON even though the fixing heater (H1, H2) is OFF  copyir.com    The SSR1 is faulty  copyir.com
E005    The web solenoid (SL4) has turned on 300 times after the fixing web length sensor (S24) stopped detecting the flag  copyir.com    The fixing web has run out  copyir.com The fixing web length sensor (S24) is faulty  copyir.com
E006-0001    The fixing drawer cannot be detected even though the 24-V door is closed    The fixing drawer has poor contact  copyir.com The fixing assembly is absent  copyir.com
E010-0001    The pickup main motor (M2) is released  copyir.com The motor is checked every 10 msec from 3000 msec after it is started to when it is stopped  copyir.com However, detection is not made when the front cover/delivery assembly cover/face-down delivery unit is released or when there is a fault in the power supply system  copyir.com    The main motor drive system has an excess load  copyir.com The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty  copyir.com The serial driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E010-0002    The pedestal main motor (M16) is released  copyir.com The motor is checked every 10 msec from 3000 msec after it is started to when it is stopped  copyir.com However, detection is not made when the front cover/delivery assembly cover/face-down delivery unit is released or when there is a fault in the power supply system  copyir.com    The main motor drive system has an excess load  copyir.com The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty  copyir.com The serial driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E010-0003    The pedestal main motor (M19) is released  copyir.com The motor is checked every 10 msec from 2000 msec after it is started to when it is stopped  copyir.com However, detection is not made when the front cover/delivery assembly cover/face-down delivery unit is released or when there is a fault in the power supply system  copyir.com    The main motor drive system has an excess load  copyir.com The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty  copyir.com The serial driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E012    XX=01: Y, XX=02: M, XX=03: C, XX=04: Bk (XX indicates the developing assembly color) XX01 The target speed cannot be attained even when the frequency of the motor drive pulse is increased to the upper limit  copyir.com XX02 The target speed cannot be attained even when the frequency of the motor drive pulse is decreased to the lower limit  copyir.com XX03 The encoder signal from the motor is not generated for the following period of time: standard: 3  copyir.com69 msec, 1/2 speed: 7  copyir.com38 msec, 1/4 speed: 14  copyir.com75 msec XX04 The motor rotates in the direction opposite the desired direction  copyir.com XX05 The spatial displacement is not corrected even when the frequency of the motor drive pulse is varied  copyir.com XX06 The target speed cannot be attained even when the frequency of the motor drive pulse is varied  copyir.com XX07 Not used  copyir.com XX08 Not used  copyir.com XX09 An error has occurred in the communication with the DC controller PCB  copyir.com    The drum motor (M3, M4, M5, M6) is faulty  copyir.com The drum motor drive system has an excess load  copyir.com The DC controller PCB is faulty  copyir.com
E013-0001    The waste toner motor has locked and, as a result, an over-current has flowed into the motor control circuit  copyir.com    The waste toner feedscrew has locked  copyir.com The waste toner feed motor is faulty  copyir.com The transfer high-voltage PCB is faulty  copyir.com The serial driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E013-0002    An open circuit has occurred in the waste toner motor  copyir.com    The waste toner feedscrew has locked  copyir.com The waste toner feed motor is faulty  copyir.com The transfer high-voltage PCB is faulty  copyir.com The serial driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-    The target speed cannot be attained even when the frequency of the motor drive pulse is changed  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-0001    The target speed cannot be attained even when the frequency of the motor drive pulse is increased to the upper limit  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-0002    The target speed cannot be attained even when the frequency of the motor drive pulse is decreased to the lower limit  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-0003    The encoder signal is not generated by the motor  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-0004    The motor rotates in the direction opposite the desired direction  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E014-0009    An error has occurred in the communication with the DC controller PCB  copyir.com    The belt motor (M15) is faulty  copyir.com The belt motor drive system has an excess load  copyir.com The drum drive AC generation PCB is faulty  copyir.com The transfer drive AC generation PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E020    XX=01: Y, XX=02: M, XX=03: C, XX=04: Bk (XX indicates the developing assembly color) XXA0During printing sequence, the difference between the maximum value and the minimum value of SIGNAL (9 samplings) is 0  copyir.com2 V (10) or less  copyir.com XX80 During printing sequence, the value of INIT-SIGNAL entered as part of initial settings has dropped to 2  copyir.com344 V (120) or lower  copyir.com XX81 During printing sequence, the value of INIT-SIGNAL entered as part of initial settings has risen to 2  copyir.com656 V (136) or higher  copyir.com XX90 During printing sequence, the correction value for INIT-SIGNAL has changed to 0 (in service mode, ADJUST>DENS>SIGG-Y/M/ C/K)  copyir.com XX91 During printing sequence, the correction value for INIT-SIGNAL has changed to 255 (in service mode, ADJUST>DENS>SIGG-Y/ M/C/K)  copyir.com XXB0 During printing sequence, the value of SIGNAL obtained by sampling and averaging is 0  copyir.com43 V (22) or lower  copyir.com XXB1 During printing sequence, the value of SIGNAL obtained by sampling and averaging is 4  copyir.com9 V (250) or higher  copyir.com XXD0During printing sequence, the value of SIGNAL remains higher than INIT-SIGNAL entered as part of initial settings by 4  copyir.com71 V (240) or more continuously for 10 prints  copyir.com XXE0 During printing sequence, the value of SIGNAL remains lower than INIT-SIGNAL entered as part of initial settings by 0  copyir.com98 V (50) or more continuously for 10 prints  copyir.com    The ATR sensor connector is disconnected  copyir.com The developing cylinder/stirring screw fails to rotate  copyir.com
E025-0101    The cartridge motor Y (M11) is found to have an over-current condition  copyir.com    The cartridge motor is faulty  copyir.com
E025-0201    The cartridge motor M (M12) is fount to have an over-current condition  copyir.com    The cartridge motor is faulty  copyir.com
E025-0301    The cartridge motor C (M13) is found to have an over-current condition  copyir.com    The cartridge motor is faulty  copyir.com
E025-0401    The cartridge motor Bk (M14) is found to have an over-current condition  copyir.com    The cartridge motor is faulty  copyir.com
E032    The Copy Data Controller-A1 or NE controller counter mechanism fails to operate  copyir.com    The Copy Data Controller-A1 or the NE controller is faulty or has an open circuit  copyir.com The system controller PCB is faulty  copyir.com
E041-0001    The fault was detected while the lifter was moving up  copyir.com The deck lifter position sensor (PS104) does not detect the lifter within 60 sec after the deck lifter UP signal is generated  copyir.com The output of the deck paper sensor (PS107) is ‘0’ when the output of the deck lifter position sensor (PS104) and that of the deck paper level sensor (PS108) are ‘1’  copyir.com    The deck lifter motor (M102) is faulty  copyir.com The deck driver PCB is faulty  copyir.com A connected device is faulty  copyir.com The deck lifter position sensor (PS104) is faulty  copyir.com The deck paper sensor (PS107) is faulty  copyir.com
E041-0002    The fault was detected while the lifter was moving down  copyir.com The deck lifter position sensor (PS104) does not detect the lifter within 60 sec after the deck lifter UP signal is generated  copyir.com The output of the deck paper sensor (PS107) is ‘0’ when the output of the deck lifter position sensor (PS104) and that of the deck paper level sensor (PS108) are ‘1’  copyir.com    The deck lifter motor (M102) is faulty  copyir.com The deck driver PCB is faulty  copyir.com A connected device is faulty  copyir.com The deck lifter position sensor (PS104) is faulty  copyir.com The deck paper sensor (PS107) is faulty  copyir.com
E043    The PLL lock signal (DMPLK) remains ‘1’ for 2 sec or more after the deck main motor drive signal is generated  copyir.com    The deck main motor (M101) is faulty  copyir.com The deck driver PCB is faulty  copyir.com A connected device is faulty  copyir.com
E051-0001    The home position of the side registration sensor (S32) cannot be detected  copyir.com The home position cannot be detected when 24-V power is turned on in response to the turning on of the main power switch or the opening and closing of the front cover/delivery assembly cover/ face-down delivery unit  copyir.com    The side registration sensor (S32) is faulty  copyir.com The side registration motor (M17) is faulty  copyir.com The duplex driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E070-    The transfer belt sensor (S51) continues to detect the home position for the transfer belt  copyir.com    The transfer belt sensor (S51) is faulty  copyir.com The transfer belt is deformed  copyir.com The transfer high-voltage PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E070-0001    The transfer belt sensor (S51) cannot detect the home position of the transfer belt  copyir.com    The transfer belt sensor (S51) is faulty  copyir.com The transfer belt is deformed  copyir.com The transfer high-voltage PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E073-0001    The transfer unit cannot be detected when the front door is closed  copyir.com    The transfer drawer connector has poor contact  copyir.com The transfer unit is absent  copyir.com
E074-0001    The output of the transfer swing sensor (S49, S50) does not change even when the transfer unit is swung  copyir.com    The transfer swing sensor (S49, S50) is faulty  copyir.com The transfer swing clutch (CL23) is faulty  copyir.com The pickup main motor (M1) is faulty  copyir.com The serial driver PCB is faulty  copyir.com
E196    X=01: Y, X=02: M, X=03: C, X=04: Bk (X indicates the developing assembly color) YY=AA, 55, 00 (data in the presence of an error) 9XYYDrum kit cartridge EEPROM check error A101 System controller PCB DIMM (absent) A102 System controller PCB memory type (not SDRAM) A103 System controller PCB memory sequential error A104 System controller PCB memory capacity error (including a mix of 64 M and 128 M) A105 System controller PCB memory type (not of recommended type) A106 System controller PCB memory capacity error (duplex model, inadequate memory) A2ZZ RCON    A memory error has occurred in the EEPROM  copyir.com
E197    X=0: System controller PCB side 2: DC controller PCB side Ex01 Serial reception error (during data reception) Ex02 Reset on CPU of other party (during data reception) Ex03 During processing of transmission/reception data (during data reception) Ex04 Serial reception error (during standby) Ex05 Reset on CPU of other party (during standby) Ex06 During processing of transmission /reception data (during standby) 020F Connection time-out    An error has occurred in communication among PCBs within the printer unit  copyir.com
E202    During a home position search, the mirror base does not return to the home position within a specific period of time  copyir.com    The mirror base malfunctions  copyir.com
E203    After scanning an original, the mirror mount does not return to the home position within a specific period of time  copyir.com The home position is detected while the mirror base is moving  copyir.com    The scanner motor malfunctions  copyir.com
E211    The thermistor reading is 0°C while the temperature is controlled to 70°C  copyir.com    The scanning lamp thermistor has an open circuit  copyir.com
E215    The thermistor reading is 170°C or higher  copyir.com    The scanning lamp thermistor has an open circuit  copyir.com
E216    The intensity sensor does not detect light 10 sec after the scanning lamp is turned on  copyir.com    The scanning lamp is faulty  copyir.com The light intensity sensor is faulty  copyir.com
E217    The temperature reading is not 70°C or higher 3 min after control to 70°C is started  copyir.com    The scanning lamp heater is faulty  copyir.com
E218    The fluorescent lamp current does not flow within a specific period of time after the ON signal has been received  copyir.com    The scanning lamp is not mounted  copyir.com The filament is broken  copyir.com
E219    The thermistor reading is 150°C or higher while the scanning lamp is on    The scanning lamp has reached the end of its life  copyir.com
E240    An error has occurred in the communication between CPUs of the reader controller PCB and the system controller PCB  copyir.com    An error has occurred in the communication between CPUs of the reader controller PCB and the system controller PCB  copyir.com
E243    An error has occurred in the communication between CPUs of the reader controller PCB and the control panel  copyir.com    An error has occurred in the communication between CPUs of the reader controller PCB and the control panel  copyir.com
E244    x=0: Pickup assembly PCB, 1: Serial driver PCB, 2: Duplex driver PCB y=0 to 7: Port of each PCB xy01 Connection check error When the main power switch is turned on, communication with each PCB cannot be established  copyir.com xy02 Parity error After communication with each PCB has been established, a parity error has occurred continuously 5 times  copyir.com xy04 Sub station reset response time-out error When the main power switch is turned on, each PCB cannot be reset (reset processing error)  copyir.com xy05 Connection check result response time-out error When the main power switch is turned on, communication with each PCB cannot be established  copyir.com xy06 Transmission end response time-out error After communication has been established with each PCB, the absence of responce has occurred continuously 5 times  copyir.com (monitoring at tall times)    The pickup assembly PCB is faulty  copyir.com The serial driver PCB is faulty  copyir.com The duplex driver PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
E351    An error has occurred in the anti-counterfeit PCB  copyir.com    An error has occurred in the anti-counterfeit PCB  copyir.com
E401    The sensor does not turn on and off twice or more within 1 sec  copyir.com    The pickup motor (M1) fails to rotate  copyir.com The pickup roller sensor (S5) is faulty  copyir.com
E402    The number of clock pulses within 200 msec is lower than a specific value  copyir.com    The belt motor (M3) fails to rotate  copyir.com The belt motor lock sensor (S10) is faulty  copyir.com
E404    The number of clock pulses within 200 msec is lower than a specific value  copyir.com    The feed motor (M2) fails to rotate  copyir.com The feed motor clock sensor (S9) is faulty  copyir.com
E411    In the absence of paper, the output of the sensor is 2  copyir.com3 V or higher  copyir.com    The original tray power sensor (S1) is faulty  copyir.com The registration sensor (S3) is faulty  copyir.com
E500    The communication between the host machine and the sorter is disrupted  copyir.com (This error is detected by the host machine  copyir.com)    Data communication is faulty
E503-0003    An error is detected in the communication with the saddle sitcher  copyir.com    A communication error has been detected  copyir.com
E504-0004    The adjustment of the sensor made using a DIP switch is faulty  copyir.com    The output of the height sensor (PS1) is faulty  copyir.com
E505-0001    At power-on, the check sum value is found to be faulty  copyir.com    The backup RAM is faulty  copyir.com
E510    After the motor drive signal has been generated, the input signal of the nonsort motor clock sensor (PI10) does not change within 60 msec  copyir.com    The no-sort motor (M6) does not rotate  copyir.com
E512-0001    At the start of operation, the target number of clock pulses cannot be obtained from the delivery motor clock  copyir.com    The delivery motor is faulty  copyir.com The delivery motor clock sensor (PI10) is faulty  copyir.com
E512-0002    During feeding, clock pulses are absent for a period equivalent of 200 mm  copyir.com    The delivery motor is faulty  copyir.com The delivery motor clock sensor (PI10) is faulty  copyir.com
E525    Auto adjustment of the bin inside paper sensor (S1, S2) fails, or the auto adjustment value has an error  copyir.com    Auto adjustment of the bin inside paper sensor (S1, S2) is faulty  copyir.com
E530    After the motor drive signal has been generated, the input signal of the guide bar HP sensor (PI3) does not change within 200 msec  copyir.com    The guide bar swing motor (M3) fails to rotate  copyir.com
E530-0001    The alignment plate does not leave the alignment plate home position sensor even when the alignment motor has been driven for 2 sec  copyir.com    The alignment motor (M3) is faulty  copyir.com The alignment plate home position sensor (PI6) is faulty  copyir.com
E530-0002    The alignment plate does not return to the alignment plate home position sensor even when the alignment motor has been driven for 2 sec  copyir.com    The alignment motor (M3) is faulty  copyir.com The alignment plate home position sensor (PI6) is faulty  copyir.com
E531    The input signal from the stapler unit HP switch (MS4) does not change for 1000 msec or more  copyir.com While the stapler unit is rotating clockwise, the home position is not detected within 600 msec  copyir.com In addition, the home position cannot be detected within 600 msec when the motor is rotated in reverse  copyir.com    The stapler unit swing motor (M4) fails to rotate  copyir.com The stapler motor (M5) fails to rotate  copyir.com
E531-0001    The stapler does not leave the stapling home position even when the stapler motor has been driven for 0  copyir.com5 sec  copyir.com    The stapler motor (M6) is faulty  copyir.com The stapler home position sensor detecting switch (MS7) is faulty  copyir.com
E531-0002    The stapler does not return to the stapling home position even when the stapler motor has been driven for 0  copyir.com5 sec  copyir.com    The stapler motor (M6) is faulty  copyir.com The stapler home position sensor detecting switch (MS7) is faulty  copyir.com
E532-0001    The stapler does not leave the stapler shift home position sensor even when the stapler shift motor has been driven for 4 sec  copyir.com    The stapler shift motor (M4) is faulty  copyir.com The stapler shift home position sensor (PI7) is faulty  copyir.com
E532-0002    The stapler shift home position cannot be detected even when the stapler shift motor has been driven for 4 sec  copyir.com    The stapler shift motor (M4) is faulty  copyir.com The stapler shift home position sensor (PI7) is faulty  copyir.com
E535-0001    The swing guide closed detecting switch does not turn on even when the delivery motor is rotated in reverse for 1 sec  copyir.com    The delivery motor (M2) is faulty  copyir.com The swing guide open sensor (PI18) is faulty  copyir.com
E535-0002    The swing guide open detecting sensor does not turn on even when the delivery motor is rotated in reverse for 1 sec  copyir.com    The safety area switch (MS3) is faulty  copyir.com The swing guide open detecting switch (MS6) is faulty  copyir.com
E535-0003    When the tray 1/2 is in the safety area switch OFF position, the swing guide closed detecting switch is found to be off  copyir.com    The delivery motor (M2) is faulty  copyir.com The swing guide closed detecting switch 2 (MS6) is faulty  copyir.com
E540-0001    The ascent operation does not end 15 sec after the tray lift motor is started  copyir.com The tray home position cannot be detected even when the tray lift motor has been driven for 15 sec  copyir.com    The tray lift motor (M5) is faulty  copyir.com The tray lift motor clock sensor 1/2 (PI19/PI20) is faulty  copyir.com The tray home position sensor (PI8) is faulty  copyir.com
E540-0002    The tray upper limit detecting switch is found to be on while the tray is moving up  copyir.com    The tray paper limit detecting switch (MS4) is faulty  copyir.com
E540-0003    There is no clock pulse from the clock sensor 1/2 for 200 msec or more when the try lifter motor is driven  copyir.com    The tray lifter motor (M5) is faulty  copyir.com The tray lifter motor clock sensor 1/2 (PI19/PI20) is faulty  copyir.com
E584-0001    The shutter closed detecting switch does not turn on even when the feed motor has been rotated in reverse for 1 sec or more  copyir.com    The feed motor (M1) is faulty  copyir.com The shutter closed detecting switch (MS4) is faulty  copyir.comPI20
E584-0002    The shutter open sensor does not turn on even when the feed motor is rotated in reverse for 1 sec or more  copyir.com    The feed motor (M1) is faulty  copyir.com The shutter open sensor (PI5) is faulty  copyir.com
E584-0003    When the tray 1/2 is in the safety area switch OFF position, the shutter closed detecting switch is found to be off  copyir.com    The safety area switch (MS3) is faulty  copyir.com The shutter closed detecting sensor (MS4) is faulty  copyir.com
E5F0-0001    The paper positioning plate home position sensor does not turn on even when the paper positioning plate motor has been driven for 1  copyir.com25 sec or more  copyir.com    The positioning plate motor (M4S) is faulty  copyir.com The power positioning plate home position sensor (PI7S) is faulty  copyir.com
E5F0-0002    The paper positioning plate home position sensor does not turn off even when paper positioning plate motor has been driven for 1 sec or more  copyir.com    The positioning plate motor (M4S) is faulty  copyir.com The power positioning plate home position sensor (PI7S) is faulty  copyir.com
E5F1-0001    The number of detention pulses of the folding motor clock sensor drops to a specific value or lower  copyir.com    The folding motor (M2S) is faulty  copyir.com The folding motor clock sensor (PI4S) is faulty  copyir.com
E5F2-0001    The guide home position sensor does not turn on even when the guide motor has been driven for 0  copyir.com4 sec or more  copyir.com    The guide motor (M3S) is faulty  copyir.com The guide home position sensor (PI13S) is faulty  copyir.com
E5F2-0002    The guide home position sensor does not turn off even when the guide motor has been driven for 1 sec or more  copyir.com    The guide motor (M3S) is faulty  copyir.com The guide home position sensor (PI13S) is faulty  copyir.com
E5F3-0001    The alignment plate home position sensor does not turn on even when the alignment motor has been driven for 0  copyir.com5 sec or more  copyir.com    The alignment motor (M5S) is faulty  copyir.com The alignment plate home position sensor (PI5S) is faulty  copyir.com
E5F3-0002    The alignment plate home position sensor does not turn off even when the alignment motor has been driven for 1 sec or more  copyir.com    The alignment motor (M5S) is faulty  copyir.com The alignment plate home position sensor (PI5S) is faulty  copyir.com
E5F4-0001    The stitching home position switch does not turn off even when the stitching motor (rear) is rotated clockwise for 0  copyir.com5 sec or more  copyir.com    The stitch motor (rear, M6S) is faulty  copyir.com The stitching home position switch (rear, PS2S) is faulty  copyir.com
E5F4-0002    During jam recovery, the stitching home position switch does not turn on even when the stitching motor (rear) is rotated counterclockwise for 0  copyir.com5 sec or more  copyir.com    The stitch motor (rear, M6S) is faulty  copyir.com The stitching home position switch (rear, PS2S) is faulty  copyir.com
E5F5-0001    The stitching home position switch does not turn off even when the stitching motor (front) is rotated clockwise for 0  copyir.com5 sec or more  copyir.com    The stitching motor (front, M7S) is faulty  copyir.com The stitching motor operating home position switch (front, PS4S) is faulty  copyir.com
E5F5-0002    During jam recovery, the stitching home position switch does not turn on even when the stitching motor (front) is rotated counterclockwise for 0  copyir.com5 sec or more  copyir.com    The stitching motor (front, M7S) is faulty  copyir.com The stitching motor operating home position switch (front, PS4S) is faulty  copyir.com
E5F6-0001    While the paper push-on plate is moving from the leading edge to the home position, the paper push-on plate home position sensor does not turn on even when the paper push-on plate motor has been driven for 0  copyir.com3 sec or more  copyir.com    The paper push-on plate motor (M8S) is faulty  copyir.com The paper push-on plate home position sensor (PI14S) is faulty  copyir.com
E5F6-0002    While the paper push-on plate is moving to the leading edge, the paper push-on plate home position sensor does not turn off even when the paper push-on plate motor has been driven for 1  copyir.com0 sec or more  copyir.com    The paper push-on plate motor (M8S) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S) is faulty  copyir.com
E5F6-0003    When the paper push-on plate is moving from the leading edge to the home position, the paper push-on plate leading edge sensor does not turn on even when the paper push-on plate motor has been driven for 1  copyir.com0 sec or more  copyir.com    The paper push-on plate motor (M8S) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S) is faulty  copyir.com
E5F6-0004    The number of detection pulse of the paper push-on plate motor clock sensor is lower than a specific value  copyir.com    The paper push-on plate motor (M8S) is faulty  copyir.com The paper push-on plate motor clock sensor (PIS) is faulty
E5F6-0005    The paper push-on plate leading edge position sensor does not turn on even when the paper push-on plate motor has been driven for 0  copyir.com3 sec or more after the paper push-on plate home position sensor is turned off  copyir.com    The paper push-on plate motor (M8S) is faulty  copyir.com The paper push-on leading edge position sensor (PI15S) is faulty  copyir.com
E5F8-0001    The connector of the guide home position sensor is found to be disconnected  copyir.com    The guide home position sensor (PI13S) has a faulty connector  copyir.com
E5F8-0002    The connector of the paper push-on plate home position sensor is found to be disconnected  copyir.com    The paper push-on plate home position sensor (PI14) has a faulty connector  copyir.com
E5F8-0003    The connector of the paper push-on plate leading edge sensor is found to be disconnected  copyir.com    The paper push-on plate leading edge sensor (PI15S) has a faulty connector  copyir.com
E5F9-0001    While the following three photointerrupters for covers have identified that the doors are closed, the inlet door open detention switch identifies the door to be open for 1 sec or more from the start of copying or the start of copier initial rotation  copyir.com Inlet door sensor (PI9S) Front door open sensor (PI2S) Delivery door open sensor (PI3S)    The inlet door open detecting switch (MS1S) is faulty  copyir.com The inlet door sensor (PI9S) is faulty  copyir.com
E5F9-0002    While the following three photointerrupters for covers have identified that the doors are closed, the front door open detecting switch identifies the front door to be open for 1 sec or more from the start of copying or the start of copier initial rotation: Inlet door sensor (P19S) Front door open sensor (PI2S) Delivery door open sensor (PI3S)    The front door open detecting switch (MS2S) is faulty  copyir.com The front door open sensor (PS2S) is faulty  copyir.com
E5F9-0003    While the following three photointerrupters for covers have identified that the doors are closed, the delivery door open detecting switch identifies the delivery door to be open for 1 sec or more from the start of copying or the start of initial rotation  copyir.com Inlet door sensor (PI9S) Font door open sensor (PI2S) Delivery door open sensor (PI3S)    The delivery door open detecting switch (MS3S) is faulty  copyir.com The delivery door open sensor (PI3S) is faulty  copyir.com
E621    An error has been detected in the communication between editor and host machine  copyir.com    The editor has an error  copyir.com
E624    An error has occurred in the communication with the editor digitizer  copyir.com    The editor has an error  copyir.com
E625    An error has occurred in the editor RAM  copyir.com    The editor has an error  copyir.com
E626    An error has occurred in the LCD of the editor  copyir.com    The editor has an error  copyir.com
E627    An error has occurred in the ASIC of the editor  copyir.com    The editor ha an error  copyir.com
E628    An error has occurred in the IPC of the editor  copyir.com    The editor has an error  copyir.com
E629    A sequential error has occurred in the editor  copyir.com    The editor has an error  copyir.com
E677-0001    DPRAM size error In communication for initialization, the DPRAM size returned by the PDL board to the host machine has an error  copyir.com (The host machine is aware of the DPRAM size in advance; the DPRAM is a dual-port RAM used for communication between the host machine and the PDL board, and is mounted on the PDL board  copyir.com)    The connection between the host machine and the PDL board is faulty  copyir.com The system software is faulty  copyir.com The hard disk is faulty  copyir.com The PDL board is faulty  copyir.com The system controller PCB of the host machine is faulty  copyir.com
E677-0002    Initialization communication error In communication for initialization, the contents of communication returned by the PDL board to the host machine have an error and, therefore, communication cannot be established  copyir.com    The connection between the host machine and the PDL board is faulty  copyir.com The system software is faulty  copyir.com The hard disk is faulty  copyir.com The PDL board is faulty  copyir.com The system controller PCB of the host machine is faulty  copyir.com
E677-0004    PDL board disconnection After the connection of the PDL board is recognized at power-on, the PDL board is disconnected  copyir.com During power-up, monitoring is executed at intervals of 2 min; however, if the CPU is not on (sleep state or the like), no error will be identified even if the PDL board is discontented  copyir.com If the PDL board is disconnected in sleep state, the absence of the PDL board will be recognized at the start of the CPU  copyir.com    The connection between the host machine and the PDL board is faulty  copyir.com The system software is faulty  copyir.com The hard disk is faulty  copyir.com The PDL board is faulty  copyir.com The system controller PCB of the host machine is faulty  copyir.com
E677-0080    Communication error An error in communication has occurred after the communication between the host machine and the PDL board has been established  copyir.com For communication related to the sleep mode (power control) of the host machine, the response from the PDL board is disrupted for 2 min or more  copyir.com    The connection between the host machine and the PDL board is faulty  copyir.com The system software is faulty  copyir.com The hard disk is faulty  copyir.com The PDL board is faulty  copyir.com The system controller PCB of the host machine is faulty  copyir.com
E677-0101    cooling fan error The rotation of the cooling fan slows down or the absence (disconnection) of the fan is detected  copyir.com The revolution of the fan is monitored at all times as long as the fan is rotating  copyir.com (The cooling fan keeps rotating while the main switch remains on  copyir.com)    The connector is disconnected  copyir.com The cooling fan is faulty  copyir.com The PDL board is faulty  copyir.com The host machine is faulty  copyir.com The system controller PCB is faulty  copyir.com
E710    At power-on, synchronization fails in the IPC communication between the reader unit and DADF/editor within a specific period of time (3 sec)  copyir.com    The DADF/editor IPC communication (initialization) has an error  copyir.com
E711    At power-on, an IPC communication error has occurred 10 times or more between the reader unit and DADF/editor within a specific period of time (1  copyir.com5 sec)  copyir.com    The DADF/editor has an IPC communication error  copyir.com
E712    The IPC communication with the reader unit is interrupted for a specific period of time (5 sec) or more  copyir.com    The DADF/editor has an IPC communication error  copyir.com
E717    When the copy start signal is generated, the count pulse is not detected by the Copier Controller-A1 or the NE controller within a specific period of time  copyir.com After connection, the Copy Data Controller-A1 or the NE Controller is disconnected  copyir.com    The Copy Data Controller-A1 or the NE Controller is faulty or has an open circuit  copyir.com The system controller PCB is faulty  copyir.com
E800-0001    The shut-off relay of the main power switch (SW1) is found to have an open circuit  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E800-0002    The AC relay (RL1) is found to have an open circuit  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E800-0003    The DC relay (RL2) is found to have an open circuit  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E800-0004    +24 VRET does not change to +24 V even when the front door, fixing door, and face-down delivery unit are all closed  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E805-0001    The fixing fan (FM1) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0002    The delivery fan (FM2) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0003    The machine cooling fan (FM4) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0004    The power supply cooling fan (FM6) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0005    The de-curling fan (FM7) is found have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0006    The kit drive cooling fan (FM10) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0007    The transfer motor cooling fan (F13) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E809    The reader unit power supply fan (FM1) is faulty  copyir.com    The reader unit power supply fan (FM1) is faulty  copyir.com
E810    XX=01: Y, XX=02: M, XX=03: C, XX=04: Bk (XX indicates the developing assembly color) XX01 The photosensitive drum unit is absent  copyir.com XX02 The wrong photosensitive drum unit is mounted (wrong color)  copyir.com XX03 The photosensitive drum is wrongly installed (wrong country model)  copyir.com    The photosensitive drum unit is faulty  copyir.com
E800-0003    The DC relay (RL2) is found to have an open circuit  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E800-0004    +24 VRET does not change to +24 V even when the front door, fixing door, and face-down delivery unit are all closed  copyir.com    The electric system has an error  copyir.com The DC controller PCB is faulty  copyir.com
E805-0001    The fixing fan (FM1) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0002    The delivery fan (FM2) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0003    The machine cooling fan (FM4) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0004    The power supply cooling fan (FM6) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0005    The de-curling fan (FM7) is found have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0006    The kit drive cooling fan (FM10) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E805-0007    The transfer motor cooling fan (F13) is found to have locked  copyir.com    The fixing fan has an error  copyir.com The delivery fan has an error  copyir.com The machine cooling fan has an error  copyir.com The power supply cooling fan has an error  copyir.com The decurling fan has an error  copyir.com The kit drive cooling fan has an error  copyir.com The transfer motor cooling fan has an error  copyir.com
E809    The reader unit power supply fan (FM1) is faulty  copyir.com    The reader unit power supply fan (FM1) is faulty  copyir.com
E810    XX=01: Y, XX=02: M, XX=03: C, XX=04: Bk (XX indicates the developing assembly color) XX01 The photosensitive drum unit is absent  copyir.com XX02 The wrong photosensitive drum unit is mounted (wrong color)  copyir.com XX03 The photosensitive drum is wrongly installed (wrong country model)  copyir.com    The photosensitive drum unit is faulty  copyir.com

خواندن 1814 دفعه
محتوای بیشتر در این بخش: « کانون Canon CLC5151 کانون Canon CP2150 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب