Your browser does not support JavaScript! > کانون Canon iR1750

   کانال تلگرام کپی ایران

(0) محصول
یکشنبه, 09 اسفند 1394 14:38

کانون Canon iR1750

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

 

E000-0001    Fixing temperature rising error
The detected temperature of the Main Thermistor failed to reach the specified temperature at temperature rising control  copyir.com    1  copyir.com Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power  copyir.com 2  copyir.com Check the connector connection  copyir.com (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3  copyir.com Replace the Fixing Assembly  copyir.com 4  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E001-0000    Detection of overheating of Fixing Assembly
The Main Thermistor detected 250 deg C or higher for 200 msec or longer on end  copyir.com    1  copyir.com Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power  copyir.com 2  copyir.com Check the connector connection  copyir.com (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3  copyir.com Replace the Fixing Assembly  copyir.com 4  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E001-0001    Detection of overheating of Fixing Assembly
The hardware circuit detected overheating of the Main Thermistor or Sub Thermistor for 30 msec or longer  copyir.com    1  copyir.com Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power  copyir.com 2  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E001-0002    Detection of overheating of Fixing Assembly
The Sub Thermistor detected 295 deg C or higher for 200msec or longer on end  copyir.com    1  copyir.com Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power  copyir.com 2  copyir.com Check the connector connection  copyir.com (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3  copyir.com Replace the Fixing Assembly  copyir.com 4  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E002-0000    Error in temperature rising of Fixing Assembly
1  copyir.com The Main Thermistor detected a temperature lower than 115 deg C for 400 msec or longer on end 6  copyir.com0 seconds after the Main Thermistor detected 100 deg C  copyir.com
2  copyir.com The Main Thermistor detected a temperature lower than 150 deg C for 400 msec or longer on end 6  copyir.com0 seconds after the Main Thermistor detected 140 deg C  copyir.com    1  copyir.com The Main Thermistor detected a temperature lower than 115 deg C for 400 msec or longer on end 6  copyir.com0 seconds after the Main Thermistor detected 100 deg C  copyir.com 2  copyir.com The Main Thermistor detected a temperature lower than 150 deg C for 400 msec or longer on end 6  copyir.com0 seconds after the Main Thermistor detected 140 deg C  copyir.com
E003-0000    Detection of fixing low temperature during printing
The Main Thermistor detected a temperature lower than 80 deg C for 200 msec or longer on end, or the Sub Thermistor detected a temperature lower than 60 deg C for 200 msec or longer on end  copyir.com    1  copyir.com Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power  copyir.com 2  copyir.com Check the connector connection  copyir.com (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3  copyir.com Replace the Fixing Assembly  copyir.com 4  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E004-0000    Thermistor disconnection detection error
Connector disconnection was detected for 30 msec on end  copyir.com    1  copyir.com Check the connector connection  copyir.com (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 2  copyir.com Replace the Fixing Assembly  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E010-0001    Main Motor (M2) rotation error
Detection was performed every 100 msec since the start of drive and there had been no lock detection signal in 2 seconds  copyir.com    1  copyir.com Check the connector between the Main Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Main Motor (M2)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E010-0002    Main Motor (M2) rotation error
Detection was performed every 100msec during the drive (after the lock detection) and the lock signal was not detected 5 times in a row (in 500 msec)  copyir.com    1  copyir.com Check the connector between the Main Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Main Motor (M2)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E013-0001    Error in rotation of Waste Toner Motor (M3)
Lock detection flag was monitored every 2msec, and the same level was detected 600 times in a row  copyir.com    1  copyir.com Check the connector connection between the Waste Toner Motor and the DC Controller PCB (J209)  copyir.com 2  copyir.com Replace the Waste Toner Motor (M3)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E014-0001    Fixing Motor (M1) rotation error
Detection was performed every 100 msec since the start of drive and there had been no lock detection signal in 2 seconds  copyir.com    1  copyir.com Check the connector connection between the Fixing Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Fixing Motor (M1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)
E014-0002    Fixing Motor (M1) rotation error
Detection was performed every 100 msec during the drive (after the lock detection) and the lock signal was not detected 5 times in a row (in 500 msec)  copyir.com    1  copyir.com Check the connector connection between the Fixing Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Fixing Motor (M1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E014-0003    Fixing Motor (M1) pressure release error
Pressure release had never been detected in 3  copyir.com0 seconds  copyir.com    1  copyir.com Check the connector connection between the Fixing Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Fixing Motor (M1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E014-0004    Fixing Motor (M1) pressurization error
Pressurization had never been detected in 3  copyir.com0 seconds    1  copyir.com Check the connector connection between the Fixing Motor and the DC Controller PCB (J203)  copyir.com 2  copyir.com Replace the Fixing Motor (M1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E020-0000    Detection of toner clog between the Hopper and the Developing Assembly
When the Developing Assembly Toner Sensor (TS2) detected "toner absent" and the Hopper Toner Sensor (TS1) detected "toner-present", the Hopper Motor (M6) was rotated 194 times with intermissions of 1 second, but the Developing Assembly Toner Sensor (TS2) could not detect "toner-present"  copyir.com * If paper is being fed, the error occurs after the paper has been delivered  copyir.com    1  copyir.com Check rotation of the Hopper Motor Gear  copyir.com (If it is rotating, the sensor may not be detecting correctly  copyir.com In that case, execute Service Mode>CLEAR>ENGIN>TNRINST to supply toner to the Developing Assembly  copyir.com) 2  copyir.com Replace the Developing Assembly Toner Sensor (TS2)  copyir.com 3  copyir.com Replace the Hopper Toner Sensor (TS1)  copyir.com 4  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E024-0000    Connector disconnection of the Developing Assembly Toner Sensor (TS2) or the DC Controller PCB (J209)
Developing Assembly Toner Sensor (TS2) connection detection signals were not detected 10 times in a row in 100 msec  copyir.com * If paper is being fed, the error occurs after the paper has been delivered  copyir.com    1  copyir.com Check the connection of the Connector (J209)  copyir.com 2  copyir.com Replace the Developing Assembly Toner Sensor (TS2)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E024-0001    Detection of disconnection of the Developing Assembly Toner Sensor (TS2)
At normal speed: Developing Assembly Toner Sensor (TS2) signals were detected 7500 times in a row at intervals of 100 msec  copyir.com At low speed: Developing Assembly Toner Sensor (TS2) signals were detected 4500 times in a row at intervals of 100 msec  copyir.com    1  copyir.com Check the connection of the Connector (J209)  copyir.com 2  copyir.com Correct the wiring  copyir.com 3  copyir.com Replace the Developing Assembly Toner Sensor (TS2)  copyir.com
E025-0000    Connector disconnection of the Hopper Toner Sensor (TS1) or the DC Controller PCB (J211)
Hopper Toner Sensor (TS1) connection detection signals were not detected 10 times in a row in 100 msec  copyir.com * If paper is being fed, the error occurs after the paper has been delivered  copyir.com    1  copyir.com Check the connection of the Connector (J211)  copyir.com 2  copyir.com Replace the Hopper Toner Sensor (TS1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E025-0001    Bottle Motor (M5) error
The lock detection flag of the Bottle Motor (M5) was monitored at intervals of 2 msec, and the same level was detected 800 times in a row  copyir.com * If paper is being fed, the error occurs after the paper has been delivered  copyir.com    1  copyir.com Replace the Bottle Motor (M5)  copyir.com 2  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E110-0001    Laser Scanner Motor error
After startup of the Laser Scanner Motor, the speed lock signal of the Laser Scanner Motor never showed lock status although a specified period of time had passed  copyir.com *When the same status was detected again after executing an error retry  copyir.com    1  copyir.com Check the Laser Scanner Unit connector  copyir.com 2  copyir.com Replace the Laser Scanner Unit  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E110-0002    Laser Scanner Motor error
After the speed lock of the Laser Scanner Motor had been settled, the speed lock signals showed unlocked status 10 times in a row at intervals of 100 msec  copyir.com *When the same status was detected again after executing an error retry  copyir.com    1  copyir.com Check the Laser Scanner Unit connector  copyir.com 2  copyir.com Replace the Laser Scanner Unit  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E110-0003    Laser Scanner Motor error
The speed lock signal of the Laser Scanner Motor never showed lock status although 6  copyir.com5 seconds (when switching from low speed to normal speed) or 8 seconds (when switching from normal speed to low speed) have passed  copyir.com *When the same status was detected again after executing an error retry  copyir.com    1  copyir.com Check the Laser Scanner Unit connector  copyir.com 2  copyir.com Replace the Laser Scanner Unit  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E196-0000    EEPROM access error
During communication with EEPROM, a communication error occurred, and the error was not cleared although a retry was executed three times  copyir.com * If paper is being fed, the error occurs after the paper has been delivered  copyir.com    1  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E197-0000    Laser Driver PCB communication error
Error in communication with the Laser Driver PCB (communication data failure)    1  copyir.com Check the Laser Scanner Unit connector  copyir.com 2  copyir.com Replace the Laser Scanner Unit  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E197-0001    Laser Driver PCB communication error
Error in communication with the Laser Driver PCB (serial communication failure)    1  copyir.com Check the Laser Scanner Unit connector  copyir.com 2  copyir.com Replace the Laser Scanner Unit  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E202-0000    CIS home position detection error
1  copyir.com Error when moving to the left side for HP check operation
2  copyir.com Error when moving to the right side for HP check operation    1  copyir.com Disconnect and then connect the Flexible Cable (Reader Controller PCB (PCB3) - Main Controller PCB (PCB2) 31pin)  copyir.com 2  copyir.com Replace the Flexible Cable  copyir.com 3  copyir.com Replace the CIS HP Sensor (PS24)  copyir.com 4  copyir.com Replace the Reader Motor (M10)  copyir.com 5  copyir.com Replace the Reader Controller PCB (PCB3)  copyir.com 6  copyir.com Replace the Main Controller PCB (PCB2)  copyir.com
E240-0000    Controller communication error
A serial communication error was detected during normal operation    1  copyir.com Check the connector connection  copyir.com (All connectors on the DC Controller PCB, J8112 on the Main Controller PCB) 2  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E240-0001    Controller communication error
A serial communication error was detected during printing  copyir.com    1  copyir.com Check the connector connection  copyir.com (All connectors on the DC Controller PCB, J8112 on the Main Controller PCB) 2  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E246-0001    System error    Contact the service company office
E246-0002    System error    Contact the service company office
E246-0003    System error    Contact the service company office
E246-0005    System error    Contact the service company office
E247-0001    System error    Contact the service company office
E261-0000    Zero cross signal error
When the relay is ON, the zero cross signal failed to be detected for 500 msec or longer  copyir.com *When the same status was detected again after executing an error retry  copyir.com    1  copyir.com Check the connector connection  copyir.com (All connectors on the DC Controller PCB) 2  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E350-0000    System error    Contact the service company office
E350-0001    System error    Contact the service company office
E350-0002    System error    Contact the service company office
E350-0003    System error    Contact the service company office
E350-3000    System error    Contact the service company office
E354-0001    System error    Contact the service company office
E354-0002    System error    Contact the service company office
E355-0000    System error    Contact the service company office
E355-0004    System error    Contact the service company office
E355-0005    System error    Contact the service company office
E530-8001    Front Alignment Motor (M4) error
At initialization of the Front Alignment Plate, the Front Alignment Plate failed to move from the Front Alignment Plate HP Sensor (S4) although the Front Alignment Motor (M4) was driven for 10 mm  copyir.com    1  copyir.com Check the connector connection of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4)  copyir.com 3  copyir.com Replace the Front Alignment Plate HP Sensor (S4)  copyir.com 4  copyir.com Replace the Front Alignment Motor (M4)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E530-8002    Front Alignment Motor (M4) error
At initialization of the Front Alignment Plate, the Front Alignment Plate failed to be detected by the Front Alignment Plate HP Sensor (S4) although the Front Alignment Motor (M4) was driven for 0  copyir.com78 seconds  copyir.com    1  copyir.com Check the connector connection of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Front Alignment Plate HP Sensor (S4) or the Front Alignment Motor (M4)  copyir.com 3  copyir.com Replace the Front Alignment Plate HP Sensor (S4)  copyir.com 4  copyir.com Replace the Front Alignment Motor (M4)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E531-8001    Staple Motor (M9) error
The Stapler failed to move from the Staple HP Sensor (S11) within the staple execution time (0  copyir.com45sec)  copyir.com    1  copyir.com Check the connector connection of the Staple Unit  copyir.com 2  copyir.com Check for open circuit of the Harness of the Staple Unit  copyir.com 3  copyir.com Replace the Staple Unit  copyir.com 4  copyir.com Replace the Finisher Controller PCB  copyir.com
E531-8002    Staple Motor (M9) error
After execution of staple operation, the motor was operated in the positive direction, but the Staple Unit could not be detected by the Staple HP Sensor (S11) within 0  copyir.com46 seconds  copyir.com Then, the motor was rotated in the negative direction, but the Staple Unit could not be detected by the Staple HP Sensor (S11) within 0  copyir.com46sec  copyir.com    1  copyir.com Check the connector connection of the Staple Unit  copyir.com 2  copyir.com Disconnect the Harness of the Staple Unit  copyir.com 3  copyir.com Replace the Staple Unit  copyir.com 4  copyir.com Replace the Finisher Controller PCB  copyir.com
E537-8001    Rear Alignment Motor (M5) error
At initialization of the Rear Alignment Plate, the Rear Alignment Plate failed to move from the Rear Alignment Plate HP Sensor (S5) although the Rear Alignment Motor (M5) was driven for 10 mm  copyir.com    1  copyir.com Check the connector connection of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5)  copyir.com 3  copyir.com Replace the Rear Alignment Plate HP Sensor (S5)  copyir.com 4  copyir.com Replace the Rear Alignment Motor (M5)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E537-8002    Rear Alignment Motor (M5) error
At initialization of the Rear Alignment Plate, the Rear Alignment Plate failed to be detected by the Rear Alignment Plate HP Sensor (S5) although the Rear Alignment Motor (M5) was driven for 0  copyir.com78sec  copyir.com    1  copyir.com Check the connector connection of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Rear Alignment Plate HP Sensor (S5) or the Rear Alignment Motor (M5)  copyir.com 3  copyir.com Replace the Rear Alignment Plate HP Sensor (S5)  copyir.com 4  copyir.com Replace the Rear Alignment Motor (M5)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E540-8001    Stack Tray Shift Motor (M8) error
The Stack Tray Shift Motor (M8) was driven for 4 seconds, but the Stack Tray shifting operation could not be completed  copyir.com    1  copyir.com Check the connector connection of the Stack Tray Paper Height Sensor (S9) or the Stack Tray Shift Motor (M8)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Stack Tray Paper Height Sensor (S9) or the Stack Tray Shift Motor (M8)  copyir.com 3  copyir.com Replace the Stack Tray Paper Height Sensor (S9)  copyir.com 4  copyir.com Replace the Stack Tray Shift Motor (M8)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E575-8002    Gripper Motor (M7) error
The gripper unit does not leave the gripper unit home position when the Gripper Motor (M7) has been driven for 3  copyir.com8 seconds  copyir.com    1  copyir.com Check the connector connection of the Gripper HP Sensor (S7) or the Gripper Motor (M7)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Gripper HP Sensor (S7) or the Gripper Motor (M7)  copyir.com 3  copyir.com Replace the Gripper HP Sensor (S7)  copyir.com 4  copyir.com Replace the Gripper Motor (M7)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E575-8004    Gripper Motor (M7) clock error
When the Gripper Motor (M7) was operated, the Gripper Encoder Sensor (S8) detected rotation of 400 clocks or more  copyir.com    1  copyir.com Check the connector connection of the Gripper Encoder Sensor (S8) or the Gripper Motor (M7)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Gripper Encoder Sensor (S8) or the Gripper Motor (M7)  copyir.com 3  copyir.com Replace the Gripper Encoder Sensor (S8)  copyir.com 4  copyir.com Replace the Gripper Motor (M7)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E577-8001    Paddle Motor (M3) error
Although the Paddle Motor (M3) was driven for 175 steps, the Paddle failed to move from the Paddle HP Sensor (S3)  copyir.com    1  copyir.com Check the connector connection of the Paddle HP Sensor (S3) or the Paddle Motor (M3)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Paddle HP Sensor (S3) or the Paddle Motor (M3)  copyir.com 3  copyir.com Replace the Paddle HP Sensor (S3)  copyir.com 4  copyir.com Replace the Paddle Motor (M3)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E577-8002    Paddle Motor (M3) error
The Paddle Motor (M3) was driven for 2 seconds, but the Paddle could not be detected by the Paddle HP Sensor (S3)  copyir.com    1  copyir.com Check the connector connection of the Paddle HP Sensor (S3) or the Paddle Motor (M3)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Paddle HP Sensor (S3) or the Paddle Motor (M3)  copyir.com 3  copyir.com Replace the Paddle HP Sensor (S3)  copyir.com 4  copyir.com Replace the Paddle Motor (M3)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E583-8001    Tray Auxiliary Guide Motor (M6) error
The Tray Auxiliary Guide Motor (M6) was driven for 30 mm, but the Tray Auxiliary Guide failed to move from the Tray Auxiliary Guide HP Sensor (S6)  copyir.com    1  copyir.com Check the connector connection of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6)  copyir.com 3  copyir.com Replace the Tray Auxiliary Guide HP Sensor (S6)  copyir.com 4  copyir.com Replace the Tray Auxiliary Guide Motor (M6)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E583-8002    Tray Auxiliary Guide Motor (M6) error
The Tray Auxiliary Guide Motor (M6) was driven for 1  copyir.com8 seconds, but the Tray Auxiliary Guide could not be detected by the Tray Auxiliary Guide HP Sensor (S6)  copyir.com    1  copyir.com Check the connector connection of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6)  copyir.com 2  copyir.com Check for open circuit of the Harness of the Tray Auxiliary Guide HP Sensor (S6) or the Tray Auxiliary Guide Motor (M6)  copyir.com 3  copyir.com Replace the Tray Auxiliary Guide HP Sensor (S6)  copyir.com 4  copyir.com Replace the Tray Auxiliary Guide Motor (M6)  copyir.com 5  copyir.com Replace the Finisher Controller PCB  copyir.com
E719-0000    Error in communication with the Copy Card Reader-F1 (serial communication)
Card Reader was not connected at department management setting  copyir.com    1  copyir.com Check the connection with the Card Reader  copyir.com 2  copyir.com Remove the Card Reader, and execute the following: service mode > #CLEAR > ERR > E719  copyir.com
E736-0000    Fax Board mismatch error
Combination of the Fax Board type and the country was mismatched    This error occurred in the following cases  copyir.com - Fax Board for non-Chinese models was installed to a Chinese model  copyir.com - Fax Board for Chinese models was installed to a non-Chinese model  copyir.com - For Chinese models, replace the Fax Board with that for Chinese models  copyir.com - For non-Chinese models, replace the Fax Board with that for non- Chinese models
E804-0000    Power Supply Cooling Fan (FM4) error
A lock signal was detected for 5 seconds while the Power Supply Cooling Fan (FM4) was being stopped  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Power Supply Cooling Fan (FM4)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E804-0001    Error in rotation of the Power Supply Cooling Fan (FM4)
A lock signal could not be detected for 5 seconds while the Power Supply Cooling Fan (FM4) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Power Supply Cooling Fan (FM4)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E805-0000    Heat Exhaust Fan (Rear) (FM6) error
A lock signal was detected for 5 seconds while the Heat Exhaust Fan (Rear) (FM6) was being stopped  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J212) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Heat Exhaust Fan (Rear) (FM6)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E805-0001    Error in rotation of the Heat Exhaust Fan (Rear) (FM6)
A lock signal could not be detected for 5 seconds while the Heat Exhaust Fan (Rear) (FM6) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J212) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Heat Exhaust Fan (Rear) (FM6)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E805-0002    Heat Exhaust Fan (Front) (FM5) error
A lock signal was detected for 5 seconds while the Heat Exhaust Fan (Front) (FM5) was being stopped  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J212) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Heat Exhaust Fan (Front) (FM5)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E805-0003    Error in rotation of the Heat Exhaust Fan (Front) (FM5)
A lock signal was detected for 5 seconds while the Heat Exhaust Fan (Front) (FM5) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J212) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Heat Exhaust Fan (Front) (FM5)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E820-0000    Developing Cooling Fan (Front) (FM7) error
A lock signal was detected for 5 seconds while the Developing Cooling Fan (Front) (FM7) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Developing Cooling Fan (Front) (FM7)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E820-0001    Error in rotation of the Developing Cooling Fan (Front) (FM7)
A lock signal could not be detected for 5 seconds while the Developing Cooling Fan (Front) (FM7) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Developing Cooling Fan (Front) (FM7)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E820-0002    Developing Cooling Fan (Rear) (FM8) error
A lock signal was detected for 5 seconds while the Developing Cooling Fan (Rear) (FM8) was being stopped  copyir.com *The same status was detected again after executing an error retry    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Developing Cooling Fan (Rear) (FM8)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E820-0003    Error in rotation of the Developing Cooling Fan (Rear) (FM8)
A lock signal was detected for 5 seconds while the Developing Cooling Fan (Rear) (FM8) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J209) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Developing Cooling Fan (Rear) (FM8)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0000    Delivery Cooling Fan (Front) (FM3) error
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Front) (FM3) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Front) (FM3)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0001    Error in rotation of the Delivery Cooling Fan (Front) (FM3)
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Front) (FM3) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Front) (FM3)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0002    Delivery Cooling Fan (Center) (FM2) error
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Center) (FM2) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Center) (FM2)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0003    Error in rotation of the Delivery Cooling Fan (Center) (FM2)
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Center) (FM2) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Center) (FM2)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0004    Delivery Cooling Fan (Rear) (FM1) error
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Rear) (FM1) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Rear) (FM1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com
E822-0005    Error in rotation of the Delivery Cooling Fan (Rear) (FM1)
A lock signal was detected for 5 seconds while the Delivery Cooling Fan (Rear) (FM1) was being driven  copyir.com *The same status was detected again after executing an error retry  copyir.com    1  copyir.com Disconnect and then connect the connector (J210) on the DC Controller PCB (PCB1) to check the connection  copyir.com 2  copyir.com Replace the Delivery Cooling Fan (Rear) (FM1)  copyir.com 3  copyir.com Replace the DC Controller PCB (PCB1)  copyir.com

خواندن 1675 دفعه
محتوای بیشتر در این بخش: « کانون Canon iR1740 کانون Canon iR2000 »

نظرات (0)

نظر ارسال شده‌ی جدیدی وجود ندارد

دیدگاه خود را بیان کنید

  1. ارسال دیدگاه بعنوان یک مهمان -
پیوست ها (0 / 3)
اشتراک‌گذاری موقعیت مکانی شما

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب