Your browser does not support JavaScript! > کانون Canon iR3045

   کانال تلگرام کپی ایران

(0) محصول
یکشنبه, 09 اسفند 1394 16:54

کانون Canon iR3045

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-0001    The temperature of the fixing assembly is abnormally high  copyir.com
While startup control is under way, the reading of the main thermistor is less than 30 deg C continuously for 200 msec or more 1 sec after the start of power supply  copyir.com While startup control is under way, the reading of the main thermistor is less than 70 deg C continuously for 200 msec or more 2 sec after the start of power supply  copyir.com While startup control is under way, the reading of the main thermistor is less than 120 deg C continuously for 200 msec 6 sec after the start of power supply  copyir.com The startup control does not end 30 sec after the start of power supply  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the main thermistor  copyir.com Replace the DC controller PCB  copyir.com
E001-0000    The temperature of the fixing assembly is abnormally high  copyir.com
The reading of the main thermistor is 250 deg C or more continuously for 200 msec  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the main thermistor  copyir.com Replace the DC controller PCB  copyir.com
E001-0001    The temperature of the fixing assembly is abnormally high  copyir.com
The hardware circuit detects overheating of the main or sub thermistor for 200 msec  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the DC controller PCB  copyir.com
E001-0002    The temperature of the fixing assembly is abnormally high  copyir.com
The reading of the sub thermistor is 295 deg C or more continuously for 200 msec  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the sub thermistor  copyir.com Replace the DC controller PCB  copyir.com
E002-0000    The rise in temperature of the fixing assembly is faulty
While startup control is under way, the reading of the main thermistor is less than 115 deg C continuously for 400 msec 1  copyir.com3 sec after it has indicated 100 deg C  copyir.com While startup control is under way, the reading of the main thermistor is less than 150 deg C continuously for 400 msec 1  copyir.com3 sec after it has indicated 140 deg C  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the main thermistor  copyir.com Replace the DC controller PCB  copyir.com
E003-0000    The fixing temperature is too low after a standby state  copyir.com
While regular temperature control is under way, the reading of the main thermistor is less than 140 deg C continuously for 400 msec or more  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the main thermistor  copyir.com Replace the DC controller PCB  copyir.com
E007-0000    The rotation of the fixing film is faulty  copyir.com
While the fixing motor is rotating, the marker signal is not detected for 6 sec with the reading of the main thermistor indicating 100 deg C or more  copyir.com    Reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com Replace the main thermistor  copyir.com Replace the DC controller PCB  copyir.com
E010-0001    The rotation of the main motor is faulty  copyir.com
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec  copyir.com    Replace the main motor  copyir.com Replace the DC controller PCB  copyir.com
E010-0002    The rotation of the main motor is faulty  copyir.com
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence  copyir.com    Replace the main motor  copyir.com Replace the DC controller PCB  copyir.com
E014-0001    The rotation of the fixing motor is faulty  copyir.com
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec    Replace the fixing motor  copyir.com Replace the DC controller PCB  copyir.com
E014-0002    The rotation of the fixing motor is faulty  copyir.com
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence  copyir.com    Replace the fixing motor  copyir.com Replace the DC controller PCB  copyir.com
E019-0000    The waste toner case is full, or the waste toner case full sensor is faulty
When the waste toner case is identified as being full for 2000 prints continuously, an alert is issued; thereafter, the case is identified as being full continuously for 100 prints    Replace the waste toner sensor  copyir.com Replace the DC controller PCB  copyir.com
E020-0000    The path between the sub hopper and the developing assembly is clogged with toner  copyir.com
The developing assembly toner sensor detects the absence of toner, while the sub hopper toner sensor detects the presence of toner  copyir.com With the developing clutch turned on, the hopper feedscrew motor is rotated for 1 sec intermittently 194 times; still, the developing assembly toner sensor does not detect the presence of toner  copyir.com    Replace the developing assembly toner sensor  copyir.com Replace the sub hopper toner sensor  copyir.com Replace the DC control PCB  copyir.com
E024-0000    The developing assembly connector is disconnected  copyir.com
The connection detection signal is absent continuously for 100 msec  copyir.com    Replace the developing assembly toner sensor  copyir.com Connect the connector  copyir.com Replace the DC controller PCB  copyir.com
E025-0000    The hopper motor or the bottle motor is faulty  copyir.com
The sub hopper toner sensor connection detection signal is absent for 100 msec 10 times in sequence  copyir.com    Replace the sub hopper toner sensor  copyir.com Connect the connector  copyir.com Replace the detection PCB  copyir.com
E025-0001    The hopper motor or the bottle motor is faulty  copyir.com
While the hopper motor is rotating, the motor error lock signal is detected continuously 4 times every 56 msec  copyir.com Or, while the bottle motor is rotating, the motor error lock signal is detected 22 times in sequence every 10 msec  copyir.com    Replace the hopper motor  copyir.com Replace the bottle motor  copyir.com Replace the DC controller PCB  copyir.com
E032-0001    The NE controller counter malfunctions  copyir.com
An open circuit is detected for the count pulse signal  copyir.com    Turn off the main power, and check the cable for an open circuit; then, turn the main power back on  copyir.com
E064-0001    The voltage of the power supply is faulty (high-voltage error)  copyir.com
The value read from the EEPORM is outside a specific range  copyir.com    Turn off and then back on the main power  copyir.com Replace the EEPROM  copyir.com
E064-0002    The voltage of the power supply is faulty (high-voltage error)  copyir.com
While output is being generated, the AD value of the primary DC voltage is 230 (DEC) or more for 100 msec 2 times in sequence  copyir.com (However, after output, it is not detected for 100 msec  copyir.com)    Replace the high-voltage power supply  copyir.com Replace the DC controller PCB  copyir.com
E064-0003    The voltage of the power supply is faulty (high-voltage error)  copyir.com
While output is being generated, the AD value of the developing DC voltage is 224 (DEC) or more for 10 msec 2 times in sequence  copyir.com (However, after output, it is not detected for 100 msec  copyir.com)    Replace the high-voltage power supply  copyir.com Replace the DC controller PCB  copyir.com
E064-0004    The voltage of the power supply is faulty (high-voltage error)  copyir.com
While output is being generated, the AD value of the transfer output current is 205 (DEC) or more for 100 msec 2 times in sequence  copyir.com (However, after output, it is not detected for 100 msec  copyir.com)    Replace the high-voltage power supply  copyir.com Replace the controller PCB  copyir.com
E064-0005    The voltage of the power supply is faulty (high-voltage error)  copyir.com
While output is being generated, the AD value of the transfer output voltage is 0 (DEC) for 100 msec 2 times in sequence  copyir.com (However, after output, it is not detected for 100 msec  copyir.com)    Replace the high-voltage power supply  copyir.com Replace the DC controller PCB  copyir.com
E100-0001    The BD interval is outside a specific range  copyir.com
After the machine has become ready for image formation (i  copyir.come  copyir.com, the scanner motor is ready for operation, and the laser has been turned on), an error has occurred 50 times or more (BD error)  copyir.com    Replace the laser unit  copyir.com Replace the DC controller PCB  copyir.com Check the wiring  copyir.com
E110-0001    The scanner motor is faulty  copyir.com
The scanner motor speed lock signal does not indicate a locked state a specific period of time after the scanner motor has been started  copyir.com    Replace the laser unit  copyir.com Replace the DC controller PCB  copyir.com Check the wiring  copyir.com
E110-0002    The scanner motor is faulty  copyir.com
The speed lock signal indicates a deviation 10 times in sequence at intervals of 10 msec after the signal has indicated a locked state  copyir.com    Replace the laser unit  copyir.com Replace the DC controller PCB  copyir.com Check the wiring  copyir.com
E110-0003    The scanner motor is faulty  copyir.com
With the image clock switched over, the scanner motor speed lock signal does not indicate a locked state 6  copyir.com5 sec after a switchover is made from low to normal speed or 8 sec after a switchover is made from normal to low speed    Replace the laser unit  copyir.com Replace the DC controller PCB  copyir.com Check the wiring  copyir.com
E191-0000    There is an error in the communication with the high-voltage power supply
The data transmission/reception does not end normally 500 msec after the most recent transmission/reception of data ended normally  copyir.com    Replace the high-voltage power supply  copyir.com Replace the DC controller PCB  copyir.com
E202-0001    There is an error in the detection of the CIS home position  copyir.com
The attempt to detect the home position fails when the CIS is moved forward    Disconnect and then connect the harness connector  copyir.com Replace the following as necessary: scanner home position sensor, scanner motor, reader controller PCB  copyir.com
E202-0002    There is an error in the detection of the CIS home position  copyir.com
The attempt to detect the home position fails when the CIS is moved back  copyir.com    Disconnect and then connect the harness connector  copyir.com Replace the following as necessary: scanner home position sensor, scanner motor, reader controller PCB  copyir.com
E225-0001    The light intensity of the CIS is faulty  copyir.com
During shading operation, the intensity is below a specific level  copyir.com    Disconnect and then connect the flexible cable  copyir.com Replace the following as necessary: flexible cable, CIS, reader controller PCB  copyir.com
E225-0002    The light intensity of the CIS is faulty  copyir.com
During DF stream reading, the sheet-to-sheet light intensity is faulty  copyir.com    Disconnect and then connect the flexible cable  copyir.com Replace the following as necessary: flexible cable, CIS, reader controller PCB  copyir.com
E227-0001    The reader unit power supply is faulty  copyir.com
At time of power-on, the 24-V port is off  copyir.com    Disconnect and then connect the power supply harness connector  copyir.com Replace the power supply  copyir.com
E227-0002    The reader unit power supply is faulty  copyir.com
At the start of a job, the 24-V port is off  copyir.com    Disconnect and then connect the power supply harness connector  copyir.com Replace the power supply  copyir.com
E227-0003    The reader unit power supply is faulty  copyir.com
At the end of a job, the 24-V port is off  copyir.com    Disconnect and then connect the power supply harness connector  copyir.com Replace the power supply  copyir.com
E227-0004    The reader unit power supply is faulty  copyir.com
When a load is being driven, the 24-V port is off  copyir.com    Disconnect and then connect the power supply harness  copyir.com Replace the power supply  copyir.com
E248-0000    The backup memory is faulty  copyir.com
[Cause] A check error has occurred on the backup SRAM board  copyir.com [Location] bottom ROM [Timing of Detection] once when the boot ROM is started up    1  copyir.com Check the presence/absence of a backup SRAM PCB  copyir.com 2  copyir.com Disconnect and then connect the backup SRAM PCB  copyir.com 3  copyir.com Replace the backup SRAM PCB with a new one  copyir.com
E248-0001    The backup memory is faulty  copyir.com
An error has occurred at power-on  copyir.com    Replace the reader controller PCB  copyir.com
E248-0002    The backup memory is faulty  copyir.com
An error has occurred during a write operation  copyir.com    Replace the reader controller PCB  copyir.com
E248-0003    The backup memory is faulty  copyir.com
An error has occurred during a read operation following a write operation  copyir.com    Replace the reader controller PCB  copyir.com
E261-0000    The zero-cross signal is faulty  copyir.com
When the relay is on, the zero-cross signal is not detected for 500 msec or more  copyir.com    Replace the AC driver PCB  copyir.com Replace the DC controller PCB  copyir.com
E315-0007    There is an error in image data  copyir.com
There is an error in JBIG encoding  copyir.com    Turn off and then back on the power  copyir.com
E315-000d    There is an error in image data  copyir.com
There is an error in JBIG decoding  copyir.com    Turn off and then back on the power  copyir.com
E400-0001    DF communication error
Check sum error    Disconnect and then connect the connector  copyir.com Replace the reader controller PCB  copyir.com Replace the ADF controller PCB  copyir.com
E400-0002    DF communication error
Reception status error    Disconnect and then connect the connector  copyir.com Replace the reader control PCB  copyir.com Replace the ADF control PCB  copyir.com
E400-0003    DF communication error
Reception interrupt error    Disconnect and then connect the connector  copyir.com Replace the reader controlled PCB  copyir.com Replace the ADF controller PCB  copyir.com
E490-0001    Wrong DF
The installed DF is not of a supported type  copyir.com    Install an ADF that is compatible with the machine  copyir.com
E500-0001    Finisher communication error
Data communication could not be performed normally  copyir.com It has been retried three times in vain  copyir.com    Replace the finisher controller PCB  copyir.com Replace the DC controller PCB  copyir.com
E503-0001    fault in communicatio n with the finisher (Finisher-Q3/ Q4)    
E503-0002    fault in communicatio n between finisher and saddle unit    Replace the finisher controller PCB  copyir.com Replace the saddle controller PCB  copyir.com Check the cable  copyir.com
E503-0003    fault in communicatio n betweenf inisher and punch unit    Replace the finisher controller PCB  copyir.com Replace the punch drive PCB  copyir.com Check the cable  copyir.com
E505-0001    fault in the backup memory of the finisher (common among all finishers)
fault in the data stored in backup memory    Turn off the main power  copyir.com Check the wiring of the DC controller PCB and the finisher controller, and check the fuse of the 24-V power supply  copyir.com Thereafter, turn the main power back on  copyir.com
E505-0002    fault in the backup memory of the finisher (common among all finishers)
fault in the EEPROM data of the punch unit    Replace the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E514-0001    fault in stack delivery motor (Finisher-S1)
When the stack retaining spacer is returned to home position, the belt escape home position sensor does not go on within 1  copyir.com5 sec  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stack delivery motor  copyir.com Check the stack delivery drive mechanism  copyir.com
E514-0001    fault in trailing edge assist motor (Finisher-Q3/ Q4)
The home position sensor does not go off even when the trailing edge assist motor has rotated for a specific period of time  copyir.com    Replace the finisher control PCB  copyir.com Replace the trailing edge assist motor  copyir.com
E514-0002    fault in stack delivery motor (Finisher-S1)When the stack retaining spacer is shifted from home position, the belt escape home position sensor does not go off within 1  copyir.com5 sec  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stack delivery motor  copyir.com Check the stack delivery drive mechanism  copyir.com
E514-0002    fault in trailing edge assist motor (Finisher-Q3/ Q4)
The home position sensor does not go on even after the trailing edge assist motor has rotated for a specific period of time  copyir.com    Replace the finisher control PCB  copyir.com Replace the trailing edge assist motor  copyir.com
E519-0001    Gear change motor error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the gear change motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the gear change motor  copyir.com Check the gear change mechanism  copyir.com
E519-0002    Gear change motor error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the gear change motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the gear change motor  copyir.com Check the gear change mechanism  copyir.com
E530-0001    Front alignment error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the front alignment motor has been rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the front alignment motor  copyir.com Check the front aligning plate drive mechanism  copyir.com Check the front alignment home position sensor  copyir.com
E530-0002    Front alignment error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the front alignment motor has been rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the front alignment motor  copyir.com Check the front aligning plate drive mechanism  copyir.com Check the front alignment home position sensor  copyir.com
E530-8001    Rear alignment error (Finisher-S1)
The home position sensor does not go on within 2000 msec after the start of operation when the rear aligning plate is shifted to home position  copyir.com    Replace the finisher controlled PCB  copyir.com Replace the rear alignment motor  copyir.com Check the rear aligning plate drive mechanism  copyir.com Check the rear alignment home position sensor  copyir.com
E530-8002    Rear alignment error (Finisher-S1)
The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is shifted from home position  copyir.com    Replace the finisher controlled PCB  copyir.com Replace the rear alignment motor  copyir.com Check the rear aligning plate drive mechanism  copyir.com Check the rear alignment home position sensor  copyir.com
E531-0001    Stapler error (Finisher-Q3/Q4)
The home position sensor does not go off even when the stapler motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler  copyir.com Check the harness  copyir.com
E531-0002    Stapler error (Finisher-Q3/Q4)
The home position sensor does not go on even when the stapler motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler  copyir.com Check the harness  copyir.com
E531-8001    Stapler error (Finisher-S1)
At time of staple jam recovery, the home position sensor does not go on with 500 msec after the start of reverse rotation of the stapler motor    Replace the finisher controller PCB  copyir.com Replace the stapler  copyir.com Check the harness  copyir.com
E531-8002    Stapler error (Finisher-S1)
The home position sensor does not go off within 500 msec after the stapler motor has been started  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler  copyir.com Check the harness  copyir.com
E532-0001    Stapler shift error (Finisher-Q3/ Q4)
The home position sensor does not go off even after the stapler shift motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler shift motor  copyir.com Check the stapler shift home position sensor  copyir.com Check the harness  copyir.com
E532-0002    Stapler shift error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the stapler shift motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler shift motor  copyir.com Check the stapler shift home position sensor  copyir.com Check the harness  copyir.com
E532-8001    Stapler shift error (Finisher-S1)
The stapler slide home position sensor does not go on within 11 sec when the stapler is shifted to home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler shift motor  copyir.com Check the stapler shift home position sensor  copyir.com Check the harness  copyir.com
E532-8002    Stapler shift error (Finisher-S1)
The stapler slide home position sensor does not go off within 1  copyir.com0 sec when the stapler is shifted from home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the stapler shift motor  copyir.com Check the stapler shift home position sensor  copyir.com Check the harness  copyir.com
E535-0001    Swing cam error (Finisher-S1)
The home position sensor does not go off within 1000 msec after the start of operation when the swing arm is shifted from home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the swing cam motor  copyir.com Check the swing cam home position sensor  copyir.com Check the harness  copyir.com
E535-0001    Swing cam error (Finisher-Q3/ Q4)
The home position sensor does not go off even when the swing motor has rotated for a specific period of time  copyir.com    Replace the finisher controller PCB  copyir.com Replace the swing cam motor  copyir.com Check the swing cam home position sensor  copyir.com Check the harness  copyir.com
E535-0002    Swing cam error (Finisher-S1)
The home position sensor does not go off within 1  copyir.com0 sec when the stack delivery roller swing arm is moved from home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the swing cam motor  copyir.com Check the swing cam home position sensor  copyir.com Check the harness  copyir.com
E535-0002    Swing cam error (Finisher-Q3/ Q4)
The home position sensor does not go on even when the swing motor has rotated for a specific period of time    Replace the finisher controller PCB  copyir.com Replace the swing cam motor  copyir.com Check the swing cam home position sensor  copyir.com Check the harness  copyir.com
E537-0001    Rear alignment error (Finisher-Q3/ Q4)
The home position sensor does not go on within 2000 msec after the start of operation when the read aligning plate is moved to home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the rear alignment motor  copyir.com Check the rear aligning plate drive mechanism  copyir.com Check the rear alignment home position sensor  copyir.com
E537-0002    Rear alignment error (Finisher-Q3/ Q4)
The home position sensor does not go off within 1000 msec after the start of operation when the rear aligning plate is moved form home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the rear alignment motor  copyir.com Check the rear aligning plate drive mechanism  copyir.com Check the rear alignment home position sensor  copyir.com
E537-8001    Front alignment error (Finisher-S1)
The home position sensor does not go on within 2  copyir.com0 sec when the front aligning plate is moved to home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the front alignment motor  copyir.com Check the front aligning plate drive mechanism  copyir.com Check the front alignment home position sensor  copyir.com
E537-8002    Front alignment error (Finisher-S1)
The home position sensor dos not go off within 1  copyir.com0 sec when the front aligning plate is shifted from home position  copyir.com    Replace the finisher controller PCB  copyir.com Replace the front alignment motor  copyir.com Check the front aligning plate drive mechanism  copyir.com Check the front alignment home position sensor  copyir.com
E540-0002    Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Upper tray ascent/descent motor clock error    Replace the No  copyir.com 1 tray shift motor  copyir.com Replace the finisher controller PCB  copyir.com Check the tray ascent/descent mechanism  copyir.com
E540-0003    Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Area error    Replace the No  copyir.com 1 tray area sensor PCB  copyir.com Replace the finisher controller PCB  copyir.com
E540-0004    Upper tray ascent/descent motor error (Finisher -Q3/ Q4)
Safety switch activation    Check the No  copyir.com 1 tray closed detecting switch  copyir.com Replace the finisher controller PCB  copyir.com
E540-8002    Stack tray motor error (Finisher-S1)
The operation to detect the paper surface of the stack tray does not end within 1  copyir.com0 sec  copyir.com    Replace the finisher controller PCB  copyir.com Replace the tray ascent/ descent motor  copyir.com Check the stack tray drive mechanism  copyir.com Check the paper surface sensor  copyir.com
E540-8003    Stack tray motor error (Finisher-S1)
An abnormal combination of sensor states has been detected  copyir.com    Replace the finisher controller PCB  copyir.com Check the stack tray upper limit sensor  copyir.com Check the stack tray lower limit sensor  copyir.com Check the stack tray upper paper surface sensor  copyir.com Check the stack tray lower paper surface sensor  copyir.com
E542-0002    Lower tray ascent/descent motor error (Finisher-Q3/ Q4
Lower tray ascent/descent motor clock error    Replace the No  copyir.com 2 tray shift motor  copyir.com Replace the finisher controller PCB  copyir.com Check the tray ascent/descent mechanism  copyir.com
E542-0003    Lower tray ascent/descent motor error (Finisher-Q3/ Q4
Area error    Replace the No  copyir.com 2 tray shift area sensor PCB  copyir.com Replace the finisher controller PCB  copyir.com
E577-8001    Paddle error (Finisher-S1)
The paddle home position sensor does not go on within 1  copyir.com5 sec when the paddle is shifted to home position  copyir.com    Check the paddle motor  copyir.com Check the paddle home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E577-8002    Paddle error (Finisher-S1)
The paddle home position sensor does not go off within 1  copyir.com0 sec when the paddle is moved to home position  copyir.com    Check the paddle motor  copyir.com Check the paddle home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E584-0001    Shutter unit error (Finisher-Q3/ Q4)
The shutter open sensor does not go off (i  copyir.come  copyir.com, the shutter does not close)  copyir.com    Check the stack edging motor  copyir.com Check the open/ close clutch  copyir.com Check the shutter home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E584-0002    Shutter unit error (Finisher-Q3/ Q4)
The shutter open sensor does not go on (i  copyir.come  copyir.com, the shutter does not open)  copyir.com    Check the stack edging motor  copyir.com Check the open/ close clutch  copyir.com Check the shutter home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E590-0001    Punch motor error
The punching home position is not detected even when the puncher motor has been driven for 20 msec  copyir.com    Check the punch motor  copyir.com Check the punch motor clock sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E590-0002    Punch motor error
The punch home position sensor is not defected even after the motor has stopped at time of punch motor initial operation  copyir.com    Check the punch motor  copyir.com Check the punch motor clock sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E591-0001    Punch dust sensor error
Error in light-receiving voltage while light is emitted    Check the waste paper case full sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E591-0002    Punch dust sensor error
Error in light-receiving voltage while light is not emitted    Check the waste paper case full sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0001    Paper trailing edge sensor/ horizontal sensor error
Error in light-receiving voltage when light is emitted (trailing edge sensor)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0002    paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (trailing edge sensor)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch drive PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0003    Power trailing edge sensor/ registration sensor
Error in light-receiving voltage when light is emitted (horizontal registration sensor 1)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0004    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 1)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0005    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is emitted (horizontal registration sensor 2)    Check the paper training edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0006    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 2)    Check the paper training edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller  copyir.com
E592-0007    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is emitted (horizontal registration sensor 3)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-0008    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 3)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch drive PCB  copyir.com Replace the finisher controller PCB
E592-0009    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 4)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com
E592-000A    Paper trailing edge sensor/ registration sensor error
Error in light-receiving voltage when light is not emitted (horizontal registration sensor 4)    Check the paper trailing edge sensor  copyir.com Check the horizontal registration sensor  copyir.com Check the punch drive PCB  copyir.com Replace the finisher controller PCB  copyir.com
E593-0001    Punch shift motor error
The light-receiving voltage home position sensor does not go off when light is emitted  copyir.com    Check the horizontal registration motor  copyir.com Check the horizontal registration home position sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com Check the punch shift mechanism  copyir.com
E593-0002    Punch shift motor error
The light-receiving voltage home position sensor does not go on when light is not emitted  copyir.com    Check the horizontal registration motor  copyir.com Check the horizontal registration home position sensor  copyir.com Check the punch driver PCB  copyir.com Replace the finisher controller PCB  copyir.com Check the punch shift mechanism  copyir.com
E5F-0001    Saddle switch error
The inlet cover switch has been identified as being open for 1 sec or more after the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed: - inlet cover sensor (PI9S) - nt cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front over switch (MS2S) or the delivery cover switch (MS3S) is open  copyir.com Inlet cover switch (MS1S)/front cover switch (MS2S)/ delivery cover switch (MS3S) Check the inlet cover switch  copyir.com Check the inlet cover sensor  copyir.com Check the front cover open/ closed sensor  copyir.com Check the delivery cover sensor  copyir.com Replace the finisher controller    Check the inlet cover switch  copyir.com Check the inlet cover sensor  copyir.com Check the front cover open/ closed sensor  copyir.com Check the delivery cover sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F-0002    Saddle switch error
The front cover switch has been identified as being open from the start of printing or the start of initial rotation with the following sensors identifying their respective covers as being closed  copyir.com - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - front cover switch (MS2S)/ delivery cover switch (MS3S) Check the front cover switch  copyir.com Check the inlet cover sensor  copyir.com Check the front cover open/ closed sensor  copyir.com Check the delivery cover sensor  copyir.com Replace the finisher controller    Check the front cover switch  copyir.com Check the inlet cover sensor  copyir.com Check the front cover open/ closed sensor  copyir.com Check the delivery cover sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F-0003    Saddle switch error
The delivery cover switch has been identified as being open after the start of printing or the start of initial rotation of the host machine with the following sensors identifying their respective covers as being closed: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S)    Check the delivery cover switch  copyir.com Check the inlet cover sensor  copyir.com Check the inlet cover sensor  copyir.com Check the front cover open/closed sensor  copyir.com Check the delivery cover sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F0-0001    Saddle paper positioning plate error
The paper positioning plate home position sensor does to go on when the paper positioning motor has been driven for 1  copyir.com33 sec  copyir.com Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S)    Check the paper positioning plate motor  copyir.com Check the paper positioning plate home position sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the paper positioning plate drive mechanism  copyir.com
E5F0-0002    Saddle paper positioning plate error
The paper positioning plate home position sensor doest not go off when the paper positioning plate motor has been driven for 1 sec  copyir.com Paper positioning plate motor (M4S)/paper positioning plate home position sensor (P17S)    Check the paper positioning plate motor  copyir.com Check the paper positioning plate home position sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the paper positioning plate drive mechanism  copyir.com
E5F1-0001    Saddle paper folding error
The number of detection pulses of the paper folding motor clock sensor has dropped below a specific value  copyir.com Paper folding motor (M2S)/ paper folding motor clock sensor (P14S)    Check the paper folding motor  copyir.com Check the paper folding motor clock sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the paper folding plate drive mechanism  copyir.com
E5F1-0002    Saddle paper folding error
The state of the paper folding home position sensor doest not change when the paper folding motor has been driven for 3 sec  copyir.com Paper folding motor (M2S)/ paper folding motor clock sensor (P14S    Check the paper folding motor  copyir.com Check the paper folding motor clock sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the paper folding plate drive mechanism  copyir.com
E5F2-0001    Saddle guide error
The guide home position sensor does not go on when the guide motor has been driven for 0  copyir.com455 sec  copyir.com Guide motor (M3S)/guide home position sensor (PI13S)    Check the guide motor  copyir.com Check the guide home position sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the guide drive mechanism  copyir.com
E5F2-0002    Saddle guide error
The guide home position sensor does not go off when the guide motor has been driven for 1 sec  copyir.com Guide motor (M3S)/guide home position sensor (PI13S)    Check the guide motor  copyir.com Check the guide home position sensor  copyir.com Replace the finisher controller PCB  copyir.com Check the guide drive mechanism  copyir.com
E5F3-0001    Saddle alignment error
The aligning plate home position sensor does not go on when the alignment motor has been driven for 0  copyir.com5 sec  copyir.com (at time of initialization, 1  copyir.com67 sec  copyir.com) Alignment motor (M5S)/ aligning plate home position sensor (PI5S)    Check the alignment motor  copyir.com Check the alignment home position sensor  copyir.com Check the aligning plate drive mechanism  copyir.com Replace the finisher controller PCB  copyir.com
E5F3-0002    Saddle alignment error
The aligning plate home position sensor does not go off when the alignment motor has been driven for 1 sec  copyir.com Alignment motor (M5S)/ aligning plate home position sensor (PI5S)    Check the alignment motor  copyir.com Check the alignment home position sensor  copyir.com Check the aligning plate drive mechanism  copyir.com Replace the finisher controller PCB  copyir.com
E5F4-0001    Saddle rear stapling error
The stitching home position sensor does not go on when the stitch motor (rear) has been rotated in reverse for 0  copyir.com5 sec or more  copyir.com Stitch motor (rear; M6S)/ stitching home position sensor (rear; MS5S)    Replace the stitcher (rear)  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F4-0002    Saddle rear stapling error
The stitching home position sensor does not go off when the stitch motor (rear) has been rotated in normal direction for 0  copyir.com5 sec or more  copyir.com Stitch motor (rear; MS)/ stitching home position sensor (rear; MS5S)    Replace the stitcher (rear)  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F5-0001    Saddle front stapling error
The stitching home position sensor does not go on when the stitch motor (front) has been rotated in reverse for 0  copyir.com5 sec or more  copyir.com Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S)    Replace the stitcher (front)  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F5-0002    Saddle front stapling error
The stitching home position sensor does not go off when the switch motor (front) has been rotated in normal direction for 0  copyir.com5 sec or more  copyir.com Stitch motor (front; M7S)/ stitching home position sensor (front; MS7S)    Replace the stitcher (front)  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F6-0001    Saddle butting error
The paper butting plate home position sensor does not go on when the paper butting plate motor has been driven for 0  copyir.com3 sec  copyir.com Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S)    Check the paper butting plate motor  copyir.com Check the paper butting plate home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F6-0002    Saddle butting error
The paper butting plate home position sensor does not go off when the paper butting plate motor has been driven for 80 msec or more  copyir.com Paper butting plate motor (M8S)/paper butting plate home position sensor (PI14S)    Check the paper butting plate motor  copyir.com Check the paper butting plate home position sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F6-0003    Saddle butting error
The number of detection pulses of the paper butting plate motor has dropped below a specific value  copyir.com paper butting plate motor (M8S)/paper butting plate motor clock sensor (PI1S)
Check the paper butting plate motor  copyir.com Check the paper butting plate motor clock sensor  copyir.com Replace the finisher controller    Check the paper butting plate motor  copyir.com Check the paper butting plate motor clock sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F6-0004    Saddle butting error
The paper butting plate leading edge sensor does not go off when the paper butting plate motor has been driven for 80 msec  copyir.com Paper butting plate motor (M8S)/paper butting plate leading edge sensor (PI15S)    Check the paper butting plate motor  copyir.com Check the paper butting plate leading edge sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F6-0005    Saddle butting error
The paper butting plate leading edge sensor does not go on when the paper butting plate motor has been driven for 0  copyir.com3 sec  copyir.com Paper butting plate more (M8S)/paper butting plate leading edge sensor (PI15S)    Check the paper butting plate motor  copyir.com Check the paper butting plate leading edge sensor  copyir.com Replace the finisher controller PCB  copyir.com
E5F8-0001    Saddle connector error
The connector of the paper butting plate home position sensor has been identified as being disconnected  copyir.com Connector of guide home position sensor (PI13S)    Connect the connector of the guide home position sensor  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F8-0002    Saddle connector error
The connector of the paper butting plate home position sensor has been identified as being disconnected  copyir.com Connector of paper butting plate home position sensor (PI14S)    Connect the connector of the paper butting plate home position sensor  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E5F8-0003    Saddle connector error
The connector of the paper butting plate leading edge sensor has been identified as being disconnected  copyir.com Connector of paper butting plate leading edge sensor (PI15S)    Connect the connector of the paper butting plate leading edge sensor  copyir.com Check the harness  copyir.com Replace the finisher controller PCB  copyir.com
E602-0001    There is an error on the hard disk  copyir.com
[Cause] An HDD detection error has occurred  copyir.com The HDD cannot be detected  copyir.com The HDD does not become ready  copyir.com The HDD returns an error  copyir.com [Detection] while boot ROM is in session BARSAC startup, mounting (usrIde) [Timing of Detection] once at startup    
E602-0002    There is an error on the hard disk  copyir.com
[Cause] There is no startup file  copyir.com The program for the main CPU does not exist on the HDD or in BOOTDEV/BOOT, and so on  copyir.com [Detection] while boot ROM is in use at time of system file loading (usrIde) [Timing of Detection] once at startup    
E602-0003    There is an error on the hard disk  copyir.com
[Cause] An HD write abort error has occurred  copyir.com The sectors for BOOTDEV on the HD cannot be read  copyir.com [Detection] BARSAC (all; at time of bootable startup) [Timing of Detection] once at startup    
E602-0006    There is an error on the hard disk  copyir.com
[Cause] A subbootable that matches the PDL type does not exit in BOOTDEV/BOOT  copyir.com [Detection] during loading of sub boot in oclibroot [Timing of Detection] once at bootable startup    
E602-0007    There is an error on the hard disk  copyir.com
[Cause] An ICC profile that matches the PDL type does not exist in BOOTDEV/PDL  copyir.com [Detection] beginning of oclibroot; judgment based on functions of PDL team that are called in [Timing of Detection] once at bootable startup    
E602-01XX    There is an error on the hard disk  copyir.com
/DOSDEV is faulty    
E602-02XX    There is an error on the hard disk  copyir.com
/FSTDEV is faulty  copyir.com    
E602-03XX    There is an error on the hard disk  copyir.com
/DOSDEV2 is faulty  copyir.com    
E602-04XX    There is an error on the hard disk  copyir.com
/FSTPDEV is faulty  copyir.com    
E602-05XX    There is an error on the hard disk  copyir.com
/DOSDEV3 is faulty  copyir.com    
E602-06XX    There is an error on the hard disk  copyir.com
/PDLDEV is faulty  copyir.com    
E602-07XX    There is an error on the hard disk  copyir.com
/DOSDEV4 is faulty  copyir.com    
E602-08XX    There is an error on the hard disk  copyir.com
/BOOTDEV is faulty  copyir.com    
E602-09XX    There is an error on the hard disk  copyir.com
/DOSDEV5 is faulty  copyir.com    
E602-FFXX    There is an error on the hard disk  copyir.com
There is an error in a partition that cannot be identified  copyir.com    
E604-0000    The image memory is faulty or is inadequate  copyir.com
The memory size does not match the model  copyir.com    Increase the memory  copyir.com
E609-0008    There is an error on the HDD  copyir.com
At startup, the HDD fails to reach a specific temperature level within a specific period of time  copyir.com    Replace the hard disk  copyir.com Replace the DC controller PCB  copyir.com
E609-0009    There is an error on the HDD  copyir.com
At time of sleep recovery, the temperature fails to reach a specific level  copyir.com    Replace the hard disk  copyir.com Replace the DC controller PCB  copyir.com
E610    The HDD coding key is faulty  copyir.com
The SRM/PCB is faulty  copyir.com The battery has become exhausted, leading to loss of SRAM contents  copyir.com    Try step 1); if it fails, try step 2)  copyir.com 1) Turn off and then back on the power switch to generate the key once again  copyir.com 2) If the same error still continues, replace the board on which the SRAM is mounted  copyir.com (Keep in mind that doing so will lead to loss of all user data  copyir.com)
E674-0001    An error has occurred in communication between the fax control PCB (2-line) and main controller PCB  copyir.com
An attempt to set mode for the fax device has failed  copyir.com    1  copyir.com Check the connection of the cable between the fax control PCB (2-line) and the main controller PCB  copyir.com 2  copyir.com Replace the ROM DIMM of the fax control PCB (2-line)  copyir.com 3  copyir.com Replace the fax control PCB (2- line)  copyir.com 4  copyir.com Replace the main controller PCB  copyir.com
E710-0001    There is an error in the initialization of the IPC  copyir.com
The machine fails to become ready 3 sec or less after the IPC chip startup  copyir.com    Check the cable  copyir.com
E710-0002    There is an error in the initialization of the IPC  copyir.com
When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized  copyir.com    Check the cable  copyir.com
E711-0001    There is an error in the IPC communication  copyir.com
The occurrence of an error has been recorded in the error register of the IPC chip 4 times or more within 1  copyir.com5 sec  copyir.com    Check the cable  copyir.com
E711-0002    There is an error in the IPC communication  copyir.com
The occurrence of an error has been recorded in the error register of the IPC chip 4 times or more within 2 sec  copyir.com    Check the cable  copyir.com
E713-0000    There is an error in the communication with the finisher  copyir.com
The communication with the finisher does not resume within 5 sec after it has been disrupted  copyir.com    Check the cable  copyir.com Replace the DC controller PCB  copyir.com Replace the finisher controller PCB  copyir.com
E716-0000    There is an error in the communication with the pedestal  copyir.com
After the presence of a pedestal has been detected, the communication fails to be normal for 5 sec    Check the cable  copyir.com Replace the DC controller PCB  copyir.com Replace the pedestal drive PCB  copyir.com
E717-0001    There is an error in the communication with the NE controller  copyir.com
The NE controller is not connected at power on, although it was connected before the power was turned off because of an error  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E717-0002    There is an error in the communication with the NE controller  copyir.com
An IPC error has occurred while the NE controller is in operation  copyir.com There is an open circuit for the IPC  copyir.com An error has occurred, and the IPC communication remains disabled    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E719-0001    There is a coin vendor error  copyir.com
The coin vendor is not connected when the power is turned on, although it was connected before the power was turned off because of an error  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E719-0002    There is a coin vendor error  copyir.com
While the coin vendor is in operation, an IPC error has occurred, IPC has developed an open circuit, or an error preventing recovery of IPC communication has occurred  copyir.com An open circuit has been detected in the line for the pickup/delivery signal  copyir.com An illegal signal has been detected  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E719-0003    There is a coin vendor error  copyir.com
While the unit price is being checked at startup, an error occurs in the communication with the coin vendor  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E719-0011    There is a coin vendor error  copyir.com
An error has occurred at new card reader startup  copyir.com The new card reader is not connected when the power is turned off, although it was connected when the power was turned off  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E719-0012    There is a coin vendor error  copyir.com
An IPC error has occurred at new card reader startup  copyir.com There is an IPC open circuit  copyir.com An error has occurred that prevents recovery of IPC communication  copyir.com    Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR> ERR  copyir.com
E730-1001    There is a PDL software error
An initialization error has occurred  copyir.com    1  copyir.com Execute PDL resetting  copyir.com 2  copyir.com Turn on the power once again  copyir.com
E730-100A    There is a PDL software error
An error that may be critical to the system (e  copyir.comg  copyir.com, failed initialization) has occurred  copyir.com    1  copyir.com Execute PDL resetting  copyir.com 2  copyir.com Turn on the power once again  copyir.com
E730-9004    There is a PDL software error
There is an error in the communication (PAI) with an external controller  copyir.com    1  copyir.com Turn on the power once main  copyir.com 2  copyir.com Check the connection of the open I/F board and the cable  copyir.com 3  copyir.com Replace the board for the external controller open I/F  copyir.com 4  copyir.com Replace the main board  copyir.com
E730-9005    There is a PDL software error
There is a fault in the connector of the vide cable to the external controller    1  copyir.com Turn on the power once main  copyir.com 2  copyir.com Check the connection of the open I/F board and the cable  copyir.com 3  copyir.com Replace the board for the external controller open I/F  copyir.com 4  copyir.com Replace the main board  copyir.com
E730-A006    There is a PDL software error
The PDL board does not respond  copyir.com A subbootable is faulty or absent    1  copyir.com Execute PDL resetting  copyir.com 2  copyir.com Turn on the power once again  copyir.com 3  copyir.com Check the connection of the SURF board  copyir.com 4  copyir.com Re-install the firmware  copyir.com 5  copyir.com Replace the main board  copyir.com
E730-A007    There is a PDL software error
There is a mismatch between the control software of the machine and the PDL control software in regard to version  copyir.com    1  copyir.com Execute PDL resetting  copyir.com 2  copyir.com Turn on the power once again  copyir.com 3  copyir.com Execute system formatting (all), and reinstall the system  copyir.com
E730-B013    There is a PDL software error
There is corruption in the font data  copyir.com    1  copyir.com Turn on the power once again  copyir.com 2  copyir.com Re-install the software  copyir.com 3  copyir.com Execute system formatting (all), and reinstall the system  copyir.com
E732-0001    There is an error in the communication with the scanner
There is a DDI-S communication error  copyir.com    1  copyir.com Check the connector used to connect the scanner  copyir.com 2  copyir.com Check the power supply of the scanner (to see if initialization takes place at startup)  copyir.com 3  copyir.com Replace the reader controller, scanner board, or main board as necessary  copyir.com
E733-0000    There is an error in the communication with the printer  copyir.com
At startup, communication with the printer fails  copyir.com    1  copyir.com Check the connector used to connect to the printer  copyir.com 2  copyir.com Check the power supply of the printer (to see if initialization takes place at startup)  copyir.com 3  copyir.com Replace the DC controller or the main board  copyir.com
E733-0001    There is an error in the communication with the printer  copyir.com
There is a DDI-P communication error    1  copyir.com Check the connection with the printer  copyir.com 2  copyir.com Check the power supply of the printer (to see if initialization takes place at startup)  copyir.com 3  copyir.com Replace the DC controller or the main board  copyir.com
E740-0002    There is an error on the Ether board  copyir.com
The MAC address is illegal  copyir.com    Replace the LAN card  copyir.com
E743-0000    There is an error in the DDI communication  copyir.com
An SCI error has occurred  copyir.com The received data is faulty  copyir.com A reception timeout condition has occurred  copyir.com An SEQ timeout error has occurred  copyir.com    Disconnect and then connect the flexible cable used to connect the reader unit and the printer unit  copyir.com Replace the following as necessary: flexible cable, reader controller PCB, main controller PCB  copyir.com
E744-0001    There is an error in the language file/boot ROM  copyir.com
The version of the language file on the HDD and that of the bootable do not match  copyir.com    Download a language file of the correct version  copyir.com
E744-0002    There is an error in the language file/boot ROM  copyir.com
The size of the language file on the HDD is too large  copyir.com    Download a language file of the correct version  copyir.com
E744-0003    There is an error in the language file/boot ROM  copyir.com
There is no language file on the HDD indicated by config  copyir.comtxt for a switchover  copyir.com    Download a language file of the correct version  copyir.com
E744-0004    There is an error in the language file/boot ROM  copyir.com
An attempt to switchover to a language on the HDD fails    Download a language file of the correct version  copyir.com
E744-1000    There is an error in the language file/boot ROM  copyir.com
The boot ROM that is mounted is of the wrong type  copyir.com    Replace the boot ROM with one of the model in question  copyir.com
E744-2000    There is an error in the language file/boot ROM  copyir.com
The engine ID indicated by the software ID is illegal  copyir.com    Replace it with a software ID of the correct model  copyir.com
E745-0001    There is a fault on the TokeRing board  copyir.com
An attempt at PCI initialization has failed  copyir.com    1  copyir.com Disconnect and then connect the TokeRing board  copyir.com 2  copyir.com Replace the TokeRing board  copyir.com
E745-0002    There is a fault on the TokeRing board  copyir.com
The MAC address is faulty    1  copyir.com Replace the TokenRing board  copyir.com
E745-0003    There is a fault on the TokeRing board  copyir.com
There is an error in the acquisition/setting of board information  copyir.com    1  copyir.com Replace the TokenRing board  copyir.com
E745-0004    There is a fault on the TokeRing board  copyir.com
There is a connection error    1  copyir.com Check the connection of the cable  copyir.com 2  copyir.com Replace the cable  copyir.com 3  copyir.com Check the power source of the MAU  copyir.com 4  copyir.com Replace the MAU  copyir.com 5  copyir.com Replace the TokenRing board  copyir.com
E745-0005    There is a fault on the TokeRing board  copyir.com
Other Errors    
E746-0003    The accessories board is of the wrong type
At startup, a board for a different model has been detected  copyir.com    Replace the UFR board of the correct type (model)  copyir.com
E748-1001    There is a mismatch between controller board and SDRAM size  copyir.com
There is a mismatch between the control board and the SDRAM  copyir.com    Check the correct combination between board and SDRAM  copyir.com
E805-0000    There is a fan error  copyir.com
While the fan is at rest, the lock signal has been detected for 5 sec  copyir.com While the fan is in operation, the lock signal is not detected for 5 sec    Replace the fan  copyir.com Replace the DC controller PCB  copyir.com

خواندن 706 دفعه
محتوای بیشتر در این بخش: « کانون Canon iR3035 کانون Canon iR3100C »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب