Your browser does not support JavaScript! > کانون Canon iR5075

   کانال تلگرام کپی ایران

(0) محصول
یکشنبه, 09 اسفند 1394 19:12

کانون Canon iR5075

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-000    The main thermistor (TH1( کپی ایران ) has poor contact or an open circuit  copyir.com The thermal switch (TP1( کپی ایران ) has an open circuit  copyir.com The fixing heater has an open circuit  copyir.com The AC driver is faulty  copyir.com The DC controller PCB is faulty  copyir.com
After the main power switch is turned on, the temperature detected by the main thermistor does not reach 70°C  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E001-0001    The main thermistor (TH1( کپی ایران ) has a short circuit  copyir.com The sub thermistor (TH2( کپی ایران ) has detected overheating  copyir.com The AC driver is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The main thermistor or the sub thermistor has detected about 230°C or higher for 2 sec  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E001-0002    The main thermistor (TH1( کپی ایران ) has a short circuit  copyir.com The sub thermistor (TH2( کپی ایران ) has detected overheating  copyir.com The AC driver is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The main thermistor has detected 230°C or higher (hard circuit detection( کپی ایران )  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E001-0003    The main thermistor (TH1( کپی ایران ) has a short circuit  copyir.com The sub thermistor (TH2( کپی ایران ) has detected overheating  copyir.com The AC driver is faulty  copyir.com
The DC controller PCB is faulty  copyir.comThe sub thermistor has detected about 236°C or higher  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E002-0000    The main thermistor (TH1( کپی ایران ) has poor contact or an open circuit  copyir.com The thermal switch (TP1( کپی ایران ) has an open circuit  copyir.com The AC driver is faulty  copyir.com The DC controller is faulty  copyir.com
The temperature of the upper fixing roller does not reach 100°C within 2 min after it has exceeded 70°C  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E003-0000    The main thermistor (TH1( کپی ایران ) has poor contact or an open circuit  copyir.com The thermal switch (TP1( کپی ایران ) has an open circuit  copyir.com The fixing heater has an open circuit  copyir.com The AC driver is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The temperature detected by the main thermistor is 70°C for 2 sec or more after it has reached 100°C  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E004-0000    The AC driver has a short circuit  copyir.com The DC controller PCB is faulty  copyir.com
The AC driver is found to have a short circuit (hard circuit detection( کپی ایران )  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E005-0000    The fixing web has been taken up  copyir.com The fixing web length sensor (PS45( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The length of fixing web that has been taken up is in excess of the specified length  copyir.com
After replacing the fixing web, be sure to reset the two web counters in service mode: COPIER>COUNTER>MISC>FIX-WEB and COPIER> COUNTER>DRBL-1>FX-WEB
E010-0000    The main motor (M2( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The clock pulses do not arrive for 2 secs or more after the main motor drive signal (MMFG( کپی ایران ) has been generated  copyir.com
E012-0000    The drum motor (M1( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG( کپی ایران ) has been generated  copyir.com
E013-0000    The waste toner feedscrew is faulty  copyir.com The water toner clock sensor (MSW2( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The rotation of the waste toner feedscrew goes out of order, and the switch (MSW2( کپی ایران ) is pressed multiple times during a specific period of time  copyir.com
E014-0000    The fixing motor (M19( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The motor clock signal is detected for 2 secs or more continuously after the fixing motor drive signal has been generated  copyir.com
E020-0000    The hopper connector is left disconnected  copyir.com The hopper motor (M9/M10( کپی ایران ) is faulty  copyir.com The toner sensor (TS1/TS2( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
During printing, the toner supply signal is '0' (absence of toner( کپی ایران ) for 2 mins  copyir.com
E032-0001    The copy data controller or the remote diagnostic device is faulty  copyir.com The Main controller PCB is faulty  copyir.com
Although once connected, the copy data controller or the remote diagnostic device has become disconnected  copyir.com
E061-0001    The laser shutter is faulty  copyir.com The laser unit is faulty  copyir.com The potential measurement PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
As the result of potential control, the drum surface potential (VL2( کپی ایران ) of the white background is about 200 V (generating solid black images( کپی ایران )  copyir.com
E061-0002    The laser shutter is faulty  copyir.com The laser unit is faulty  copyir.com The potential measurement PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The primary charging output used for print output and the drum surface potential after laser output has been made are about 200 V (generating solid black images( کپی ایران )  copyir.com
E100-0001    The BD PCB is faulty  copyir.com The laser unit is faulty  copyir.com The laser driver PCB is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC controller PCB is faulty  copyir.com
In 100 msec after the laser drive signal has been generated, the BD signal is not detected 50 times or more within 40 msecs  copyir.com
E100-0002    The BD PCB is faulty  copyir.com The laser unit is faulty  copyir.com The laser driver PCB is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC controller PCB is faulty  copyir.com
While the laser is on, the BD signal cycle is found to be outside a specific range 10 times or more  copyir.com
E110-0001    The laser scanner motor (M15( کپی ایران ) is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC controller PCB is faulty
• After the laser scanner motor drive signal has been generated, the motor ready signal (LMRDY*( کپی ایران ) does not arrive for 15 secs or more  copyir.com (stop - full speed, half-speed - full speed( کپی ایران ) • During the period of 'full speed ® half speed', the motor ready signal does not arrive for 60 secs or more after the speed change signal has been generated  copyir.com • During the period of 'full speed rotation', the motor ready signal is not detected 50 times or more (t intervals of 100 msec( کپی ایران )  copyir.com
E121-0001    The controller cooling fan (FM4( کپی ایران ) is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC controller PCB is faulty  copyir.com
Although the controller cooling fan (FM4( کپی ایران ) is being driven, the clock signal (FM4CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com
E196    The EEPROM on the DC controller PCB is faulty  copyir.com The location of the EEPROM is wrong  copyir.com The DC controller PCB is faulty  copyir.com
1abb: When data is written to the EEPROM, the data written and the data read do not match  copyir.com 2abb: When the ID read into the EEPROM and the ID into the ROM are compared, a mismatch is found  copyir.com 3abb: When ID in the EEPROM and the ID in the ROM are compared after the main power switch is turned on, a mismatch is found  copyir.com a: chip Nos  copyir.com 0 through 5 (0: IC104, 1: IC105, 2: IC109, 3: IC110, 4: IC127, 5: IC130( کپی ایران ) bb: chip faulty address (bit( کپی ایران )
E202-0001    The scanner HP sensor (PS39( کپی ایران ) is faulty  copyir.com The scanner motor (M3( کپی ایران ) is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The scanner HP sensor does not turn off even when the scanner has been moved 40 mm forward after the main power switch has been turned on or the Start key has been pressed  copyir.com
E202-0002    The scanner HP sensor (PS39( کپی ایران ) is faulty  copyir.com The scanner motor (M3( کپی ایران ) is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The scanner HP sensor does not turn on even when the scanner has been moved 450 mm in reverse  copyir.com
E204-0001    The ADF controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
During printing, the image leading edge signal does not arrive from the ADF  copyir.com
E220-0001    The lamp inverter PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The lamp inverter PCB is found to have a fault  copyir.com
E225-0000    The scanning lamp (xenon tube( کپی ایران ) is faulty  copyir.com The inverter PCB is faulty  copyir.com The CCD/AP PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
A specific signal level cannot be attained by CCD gain correction at power-on  copyir.com
E225-0002    The scanning lamp (xenon tube( کپی ایران ) is faulty  copyir.com The inverter PCB is faulty  copyir.com The CCD/AP PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The edge gain correction value changed more than a specific level compared with the correction value used for the preceding sheet  copyir.com
E240-0000    The main controller PCB  copyir.com The DC controller PCB is faulty  copyir.com
An error has occurred in the communication between the main controller PCB and the CPU of the DC controller PCB  copyir.com
E240-010B    The main controller PCB  copyir.com The DC controller PCB is faulty  copyir.com
An error occurred in the sequence during printing  copyir.com
E243-0000    The control panel CPU PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB  copyir.com
E248-0001    The EEPROM on the reader controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The ID read into the EEPROM when the main power switch has been turned on and the ID in the ROM do not match  copyir.com
E248-0002    The EEPROM on the reader controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
When data is written into EEPROM, the data written and the data read do not match  copyir.com
E248-0003    The EEPROM on the reader controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
When data is written, the ID in the EEPROM and the ID in the ROM are found not to match  copyir.com
E302-0001    The CCD/AP PCB is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The reader controller PCB is faulty  copyir.com
During shading, the reader controller PCB does not end shading in 1 sec  copyir.com
E302-0002    The CCD/AP PCB is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The reader controller PCB is faulty  copyir.com
In stream reading, the edge white accumulation (processing( کپی ایران ) does not end after a period of 10 secs  copyir.com
E315-0007    Main controller PCB, Hard disk drive
When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec  copyir.com
E315-0010    Main controller PCB, Hard disk drive
When a start command is sent to the compression/extension element of the main controller at time of decoding, an end interrupt does not occur after 4 sec  copyir.com
E412-0001    The cooling fan (FM1( کپی ایران ) is faulty  copyir.com The ADF controller PCB is faulty  copyir.com
While the cooling fan is being driven, the lock signal (FMLCK( کپی ایران ) arrives for 100 msec or more  copyir.com
E420-0001    The EEPROM is faulty  copyir.com The ADF controller PCB is faulty  copyir.com
When the host machine's power switch is turned on, the backup data of the EEPROM cannot be read or the data, if read, has an error  copyir.com
E421-0001    The EEPROM is faulty  copyir.com The ADF controller PCB is faulty  copyir.com
Backup data cannot be written to the EEPROM or the data, if written, has an error  copyir.com
E422-0001    The IPC communication has an error  copyir.com The communication line has an open circuit  copyir.com The ADF controller PCB is faulty  copyir.com
While the machine is in standby, the communication with the host machine has been interrupted for 5 secs or more  copyir.com or, while the machine is in operation, the communication with the host machine has been interrupted for 0  copyir.com5 sec or more  copyir.com
E500-0001    The finisher controller PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine  copyir.com
E503-0002    The saddle stitcher controller PCB is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The communication between the saddle stitcher controller PCB and the finisher controller PCB has been interrupted  copyir.com
E504-0001    The height sensor (PS1( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
Communication between the height sensor and the finisher controller PCB is not possible, or communication data has an error  copyir.com
E504-0002    The height sensor (PS1( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
Communication between the height sensor and the finisher controller PCB is not possible for a specific period of time  copyir.com
E504-0003    The height sensor (PS1( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
At time of power-on, the connector of the height sensor is found to be disconnected  copyir.com
E504-0004    The height sensor (PS1( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
When the height sensor is being adjusted using the DIP switch, an error occurred during the adjustment  copyir.com
E505-0001    The EEPROM is faulty  copyir.com The finisher controller PCB is faulty  copyir.com The puncher driver PCB is faulty  copyir.com
When the power switch is turned on, the check sum of the EEPROM on the finisher controller PCB is found to have an error  copyir.com
E505-0002    The EEPROM is faulty  copyir.com The finisher controller PCB is faulty  copyir.com The puncher driver PCB is faulty  copyir.com
When the power switch is turned on, the check sum of the EEPROM on the puncher driver PCB is found to have an error  copyir.com
E512-0001    The delivery motor clock sensor (PI10( کپی ایران ) is faulty  copyir.com The delivery motor (M2( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty
When operation starts, as many clocks as needed do not arrive from the delivery motor clock sensor  copyir.com
E512-0002    The delivery motor clock sensor (PI10( کپی ایران ) is faulty  copyir.com The delivery motor (M2( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty
No clock pulse arrives while paper is being moved over a distance of 200 mm  copyir.com
E530-0001    The alignment plate home position sensor (PI6( کپی ایران ) is faulty  copyir.com The alignment motor (M3( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The alignment plate does not leave home position when the alignment motor has been driven for 2 secs  copyir.com
E530-0002    The alignment plate home position sensor (PI6( کپی ایران ) is faulty  copyir.com The alignment motor (M3( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The alignment plate does not return to home position when the alignment motor has been driven for 2 secs  copyir.com
E531-0001    The stapler home position detecting switch (MS7( کپی ایران ) is faulty  copyir.com The stapler motor (M6( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The stapler does not leave home position when the stapler motor has been driven for 0  copyir.com5 sec  copyir.com
E531-0002    The stapler home position detecting switch (MS7( کپی ایران ) is faulty  copyir.com The stapler motor (M6( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The stapler does not return to home position when the stapler motor has been driven for 0  copyir.com5 sec  copyir.com
E532-0001    The stapler shift home position sensor (PI7( کپی ایران ) is faulty  copyir.com The stapler shift motor (M4( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The stapler unit does not leave home position when the stapler shift motor has been driven for 4 secs  copyir.com
E532-0002    The stapler shift home position sensor (PI7( کپی ایران ) is faulty  copyir.com The stapler shift motor (M4( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The stapler unit does not return to home position when the stapler shift motor has been driven for 4 secs  copyir.com
E535-0001    The swing motor clock sensor (PI20( کپی ایران ) is faulty  copyir.com The swing guide open sensor (PI18( کپی ایران ) is faulty  copyir.com The safety area switch (MS3( کپی ایران ) is faulty  copyir.com The swing guide closed detecting switch 2 (MS6( کپی ایران ) is faulty  copyir.com The swing motor (M7( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The swing guide closed detecting switch 2 does not turn on when the swing motor has been rotated CCW for 1 sec  copyir.com
E535-0002    The swing motor clock sensor (PI20( کپی ایران ) is faulty  copyir.com The swing guide open sensor (PI18( کپی ایران ) is faulty  copyir.com The safety area switch (MS3( کپی ایران ) is faulty  copyir.com The swing guide closed detecting switch 2 (MS6( کپی ایران ) is faulty  copyir.com The swing motor (M7( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
While the tray is moving up, the tray upper limit detection switch is found to be on  copyir.com
E535-0003    The swing motor clock sensor (PI20( کپی ایران ) is faulty  copyir.com The swing guide open sensor (PI18( کپی ایران ) is faulty  copyir.com The safety area switch (MS3( کپی ایران ) is faulty  copyir.com The swing guide closed detecting switch 2 (MS6( کپی ایران ) is faulty  copyir.com The swing motor (M7( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
When the tray lift motor is driven, clock pulses do not arrive from the clock sensor 1/2 for 200 msecs  copyir.com
E584-0001    The shutter open sensor (PI5( کپی ایران ) is faulty  copyir.com The safety area detecting switch (MS3( کپی ایران ) is faulty  copyir.com The shutter closed detecting switch (MS4( کپی ایران ) is faulty  copyir.com The No  copyir.com 2 feed motor (M8( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The shutter closed detecting switch does not turn on when the No  copyir.com 2 feed motor has been rotated CCW for 1 sec or more
E584-0002    The shutter open sensor (PI5( کپی ایران ) is faulty  copyir.com The safety area detecting switch (MS3( کپی ایران ) is faulty  copyir.com The shutter closed detecting switch (MS4( کپی ایران ) is faulty  copyir.com The No  copyir.com 2 feed motor (M8( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
The shutter open sensor does not turn on when the No  copyir.com 2 feed motor has been rotated CCW for 1 sec  copyir.com
E584-0003    The shutter open sensor (PI5( کپی ایران ) is faulty  copyir.com The safety area detecting switch (MS3( کپی ایران ) is faulty  copyir.com The shutter closed detecting switch (MS4( کپی ایران ) is faulty  copyir.com The No  copyir.com 2 feed motor (M8( کپی ایران ) is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
While the tray lift motor is in operation, the shutter closed detecting switch is found to be off when the tray 1/2 is at OFF position of the safety area detecting switch  copyir.com
E590-0001    The punch home position sensor (PI3P( کپی ایران ) is faulty  copyir.com The punch motor (M1P( کپی ایران ) is faulty  copyir.com The punch driver PCB is faulty  copyir.com
The puncher does not leave home position when the punch motor has been driven for 200 msecs  copyir.com
E590-0002    The punch home position sensor (PI3P( کپی ایران ) is faulty  copyir.com The punch motor (M1P( کپی ایران ) is faulty  copyir.com The punch driver PCB is faulty  copyir.com
The puncher does not return to home position when the punch motor has been driven for 200 msecs  copyir.com
E593-0001    The horizontal registration home position sensor (PI1P( کپی ایران ) is faulty  copyir.com The horizontal registration motor (M1P( کپی ایران ) is faulty  copyir.com The punch driver PCB is faulty  copyir.com
The puncher does not leave home position when the horizontal registration motor has been driven for 4 secs  copyir.com
E593-0002    The horizontal registration home position sensor (PI1P( کپی ایران ) is faulty  copyir.com The horizontal registration motor (M1P( کپی ایران ) is faulty  copyir.com The punch driver PCB is faulty  copyir.com
The puncher does not return to home position when the horizontal registration motor has been driven for 4 secs  copyir.com
E5F0-0001    The paper positioning plate home position sensor (PI7S( کپی ایران ) is faulty  copyir.com The paper positioning plate motor (M4S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for about 1  copyir.com3 secs  copyir.com
E5F0-0002    The paper positioning plate home position sensor (PI7S( کپی ایران ) is faulty  copyir.com The paper positioning plate motor (M4S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper positioning plate home position sensor does not turn off 1 sec after the paper positioning plate motor has been driven for 1 sec  copyir.com
E5F1-0001    The folding motor clock sensor (PI4S( کپی ایران ) is faulty  copyir.com The paper folding home position sensor (PI21S( کپی ایران ) is faulty  copyir.com The folding motor (M2S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The number of detection pulses of the folding motor clock sensor drops below a specific value  copyir.com
E5F1-0002    The folding motor clock sensor (PI4S( کپی ایران ) is faulty  copyir.com The paper folding home position sensor (PI21S( کپی ایران ) is faulty  copyir.com The folding motor (M2S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The state of the paper folding home position sensor does not change when the folding motor has been driven for 3 secs  copyir.com
E5F2-0001    The guide home position sensor (PI13S( کپی ایران ) is faulty  copyir.com The guide motor (M3S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The guide home position sensor does not turn on when the guide motor has been driven for about 0  copyir.com5 sec  copyir.com
E5F2-0002    The guide home position sensor (PI13S( کپی ایران ) is faulty  copyir.com The guide motor (M3S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The guide home position sensor does not turn off when the guide motor has been driven for 1 sec  copyir.com
E5F3-0001    The alignment home position sensor (PI5S( کپی ایران ) is faulty  copyir.com The alignment motor (M5S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0  copyir.com5 sec (initially, driven for about 1  copyir.com7 sec( کپی ایران )  copyir.com
E5F3-0002    The alignment home position sensor (PI5S( کپی ایران ) is faulty  copyir.com The alignment motor (M5S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec  copyir.com
E5F4-0001    The stitch home position sensor (rear, MS5S( کپی ایران ) is faulty  copyir.com The stitch motor (rear, M6S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The stitcher home position sensor (rear( کپی ایران ) does not turn off when the stitch motor (rear( کپی ایران ) has been rotated CW for 0  copyir.com5 sec or more  copyir.comfaulty  copyir.com
E5F4-0002    The stitch home position sensor (rear, MS5S( کپی ایران ) is faulty  copyir.com The stitch motor (rear, M6S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The stitch home position sensor (rear( کپی ایران ) does not turn on when the stitch motor (rear( کپی ایران ) has been rotated CCW for 0  copyir.com5 sec or more  copyir.com
E5F5-0001    The stitch home position senor (front, MS7S( کپی ایران ) is faulty  copyir.com The stitch motor (front, M7S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The stitch home position sensor (front( کپی ایران ) does not turn off when the stitch motor (front( کپی ایران ) has been rotated CW for 0  copyir.com5 sec or more  copyir.com
E5F5-0002    The stitch home position senor (front, MS7S( کپی ایران ) is faulty  copyir.com The stitch motor (front, M7S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The stitch home position sensor (front( کپی ایران ) does not turn on when the stitch motor (front( کپی ایران ) has been rotated CCW for 0  copyir.com5 sec or more  copyir.com
E5F6-0001    The paper push-on plate motor clock sensor (PI1S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate motor (M8S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper push-on plate home position sensor does not turn on when the paper push-on plate motor has been driven for 0  copyir.com3 sec or more  copyir.com
E5F6-0002    The paper push-on plate motor clock sensor (PI1S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate motor (M8S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper push-on plate home position sensor does not turn off when the paper push-on plate motor has been driven for 0  copyir.com3 sec or more  copyir.com
E5F6-0003    The paper push-on plate motor clock sensor (PI1S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate motor (M8S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper push-on plate leading edge position sensor does not turn off when the paper push-on plate motor has been driven for 0  copyir.com3 sec or more  copyir.com
E5F6-0004    The paper push-on plate motor clock sensor (PI1S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate motor (M8S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The number of detection pulses of the paper push-on plate motor clock sensor drops below a specific value  copyir.com
E5F6-0005    The paper push-on plate motor clock sensor (PI1S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate motor (M8S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The paper push-on plate leading edge sensor does not turn on when the paper push-on plate motor has been driven for 0  copyir.com3 sec or morere  copyir.com
E5F8-0001    The guide home position sensor (PI13S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The connector of the guide home position sensor is found to be disconnected  copyir.com
E5F8-0002    The guide home position sensor (PI13S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The connector of the paper home positioning plate home position sensor is found to be disconnected  copyir.com
E5F8-0003    The guide home position sensor (PI13S( کپی ایران ) is faulty  copyir.com The paper push-on plate home position sensor (PI14S( کپی ایران ) is faulty  copyir.com The paper push-on plate leading edge position sensor (PI15S( کپی ایران ) is faulty  copyir.com The saddle stitcher controller PCB is faulty  copyir.com
The connector of the paper push-on plate leading edge position sensor is found to be discontented  copyir.com
E5F9-0001    The inlet cover switch (MS1S( کپی ایران ) is faulty  copyir.com The front cover switch (MS2S( کپی ایران ) is faulty  copyir.com The delivery cover switch (MS3S( کپی ایران ) is faulty  copyir.com The saddle stitch controller PCB is faulty  copyir.com
When the inlet cover, front cover, and the delivery cover are found to be closed, the inlet cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing  copyir.com
E5F9-0002    The inlet cover switch (MS1S( کپی ایران ) is faulty  copyir.com The front cover switch (MS2S( کپی ایران ) is faulty  copyir.com The delivery cover switch (MS3S( کپی ایران ) is faulty  copyir.com The saddle stitch controller PCB is faulty  copyir.com
When the inlet cover, front cover, and delivery cover are found to be closed, the front cover switch detects an open condition for 1 sec or more after the start of the initial rotation of the host machine or the start of printing  copyir.com
E5F9-0003    The inlet cover switch (MS1S( کپی ایران ) is faulty  copyir.com The front cover switch (MS2S( کپی ایران ) is faulty  copyir.com The delivery cover switch (MS3S( کپی ایران ) is faulty  copyir.com The saddle stitch controller PCB is faulty  copyir.com
When the inlet cover, front cover, and delivery cover are found to be closed, the delivery cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing  copyir.com
E601-0000    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The DC controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
The main controller PCB has detected an error in control data while an image was transmitted between the main controller PCB and the hard disk drive  copyir.com
E601-0001    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The DC controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
The main controller PCB has found an error in the control data in transfer of images between main controller PCB and the DC controller PCB  copyir.com
E602-0001    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The main controller PCB is faulty  copyir.com
A mount error was detected when the hard disk was started up from the boot ROM  copyir.com
E602-0002    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The main controller PCB is faulty  copyir.com
A data read error (from the hard disk( کپی ایران ) was detected when the hard disk was started from the boot ROM  copyir.com
E602-0003    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The main controller PCB is faulty  copyir.com
A a sector error is found on the hard disk  copyir.com
E602-0004    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The hard disk drive is faulty  copyir.com The main controller PCB is faulty  copyir.com
A an error is found in the read/write address for the hard disk  copyir.com
E607-0000    The hard disk fan (FM7( کپی ایران ) is faulty  copyir.com The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC controller PCB is faulty  copyir.com
While the hard disk fan (FM7( کپی ایران ) is being driven, the clock signal (FM7CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com
E677-0001    The various printer board (accessories( کپی ایران ) are faulty  copyir.com The main controller PCB is faulty  copyir.com
An error has occurred in the communication between the various printer boards (accessories( کپی ایران ) and the main controller PCB  copyir.com
E710-0001    The DC controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
When the main power is turned on, the IPC (IC5021( کپی ایران ) on the reader controller PCB cannot be initialized  copyir.com
E710-0002    The DC controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
When the main power is turned on, the IPC (IC120( کپی ایران ) on the DC controller PCB cannot be initialized  copyir.com
E710-0003    The DC controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com The main controller PCB is faulty  copyir.com
When the main power is turned on, the IPC (IC1003( کپی ایران ) on the main controller PCB cannot be initialized  copyir.com
E711-0001    The connector is not connected properly  copyir.com The remote diagnostic device PCB is faulty  copyir.com The copy data controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
Data has been written to the error register of the IPC (IC5021( کپی ایران ) on the reader controller PCB four times or more within 1  copyir.com5 secs  copyir.com
E711-0002    The connector is not connected properly  copyir.com The remote diagnostic device PCB is faulty  copyir.com The copy data controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
Data has been written to the error register of the IPC (IC120( کپی ایران ) on the DC controller PCB four times or more within 2 secs  copyir.com
E711-0003    The connector is not connected properly  copyir.com The remote diagnostic device PCB is faulty  copyir.com The copy data controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The finisher controller PCB is faulty  copyir.com
Data has been written to the error register of the IPC (IC1003( کپی ایران ) of the main controller PCB four times or more within 2 secs  copyir.com
E712-0001    The connector is not connected properly  copyir.com The ADF 24-V power supply is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
Communication does not resume in 3 secs after data has been written to the error register of the communication IC (IPC( کپی ایران ) of the ADF controller PCB  copyir.com
E712-0002    The connector is not connected properly  copyir.com The ADF 24-V power supply is faulty  copyir.com The ADF controller PCB is faulty  copyir.com The reader controller PCB is faulty  copyir.com
The transmission bit is not enabled after a period of 10 sec at the sync register of the IPC (IC5021( کپی ایران ) on the reader controller PCB  copyir.com
E713-0000    The connector is not connected properly  copyir.com The finisher accessories power supply PCB is faulty  copyir.com The finisher controller PCB is faulty  copyir.com The DC controller PCB is faulty  copyir.com
The communications IC (IPC( کپی ایران ) on the finisher controller has gone out of order  copyir.com
E717-0001    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The copy data controller or the remote diagnostic device is faulty  copyir.com The main controller PCB is faulty  copyir.com
The copy data controller or the NE controller is out of order or an open circuit has been detected  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E719-0001    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The coin vendor is faulty  copyir.com The main controller PCB is faulty  copyir.com
The communication between the coin vendor and the main controller PCB has been interrupted  copyir.com
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR( کپی ایران )  copyir.com
E732-0001    The connector has poor contact  copyir.com The reader controller PCB is faulty  copyir.com
The main controller PCB has detected an error in the communication between the reader controller PCB and the main controller PCB  copyir.com
E732-9999    The connector has poor contact  copyir.com The reader controller PCB is faulty  copyir.com
In a printer mode, a read unit is detected by the main controller PCB  copyir.com
E733-0001    The connector has poor contact  copyir.com The DC controller PCB is faulty  copyir.com
The main controller PCB has detected an error in the communication between the DC controller PCB and the main controller PCB  copyir.com
E740-0001    The LAN card is faulty  copyir.com The main controller PCB is faulty  copyir.com
An error is detected on the LAN card at power-on (with the card inserted( کپی ایران )  copyir.com
E740-0002    The LAN card is faulty  copyir.com The main controller PCB is faulty  copyir.com
A MAC address is found to be faulty  copyir.com
E740-0003    The LAN card is faulty  copyir.com The main controller PCB is faulty  copyir.com
The LAN card register cannot be read  copyir.com
E741-0000    The PCI bus connection is not proper  copyir.com The main controller PCB is faulty  copyir.com
An error has occurred in the PCI bus  copyir.com
E743-0000    The connector has poor contact  copyir.com The main controller PCB is faulty  copyir.com
The reader controller PCB has detected an error in the communication between the main controller PCB and the reader controller PCB  copyir.com
E744-0001    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file and the main controller have a version mismatch
E744-0002    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is found to be too large  copyir.com
E744-0003    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is absent  copyir.com
E744-0004    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file cannot be read  copyir.com
E744-1000    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the bottom ROM product name is found to be a mismatch
E744-2000    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the serial number of the serial number PCB is an undefined code  copyir.com
E804-0000    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The DC power supply fan (FM6( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
While the DC power supply fan is being driven, the clock signal (FM6CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com
E805-0001    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The feed fan (FM1( کپی ایران ) is faulty  copyir.com The heat discharge fan (FM3( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
While the heat discharge fan is being driven, the clock signal (FM3CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com
E805-0002    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The feed fan (FM1( کپی ایران ) is faulty  copyir.com The heat discharge fan (FM3( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
While the feed fan is being driven, the clock signal (FM1CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com
E824-0000    The wiring is faulty (short circuit, open circuit( کپی ایران )  copyir.com The primary charging assembly cooling fan (FM2( کپی ایران ) is faulty  copyir.com The DC controller PCB is faulty  copyir.com
While the primary charging assembly cooling fan is being driven, the clock signal (FM2CLK( کپی ایران ) does not arrive for 5 secs or more  copyir.com PCB  copyir.com

خواندن 1086 دفعه
محتوای بیشتر در این بخش: « کانون Canon iR5055 کانون Canon iR5075 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب