Your browser does not support JavaScript! > کانون Canon iR8500

   کانال تلگرام کپی ایران

(0) محصول
دوشنبه, 10 اسفند 1394 11:04

کانون Canon iR8500

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E000-000    The main thermistor (TH1) has poor contact or an open circuit   copyir.ocm The thermal switch (TP1) has an open circuit   copyir.ocm The fixing heater has an open circuit   copyir.ocm The AC driver is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
After the main power switch is turned on, the temperature detected by the main thermistor does not reach 70°C   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E001-0001    The main thermistor (TH1) has a short circuit   copyir.ocm The sub thermistor (TH2) has detected overheating   copyir.ocm The AC driver is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The main thermistor or the sub thermistor has detected about 230°C or higher for 2 sec   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E001-0002    The main thermistor (TH1) has a short circuit   copyir.ocm The sub thermistor (TH2) has detected overheating   copyir.ocm The AC driver is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The main thermistor has detected 230°C or higher (hard circuit detection)   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E001-0003    The main thermistor (TH1) has a short circuit   copyir.ocm The sub thermistor (TH2) has detected overheating   copyir.ocm The AC driver is faulty   copyir.ocm
The DC controller PCB is faulty   copyir.ocmThe sub thermistor has detected about 236°C or higher   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E002-0000    The main thermistor (TH1) has poor contact or an open circuit   copyir.ocm The thermal switch (TP1) has an open circuit   copyir.ocm The AC driver is faulty   copyir.ocm The DC controller is faulty   copyir.ocm
The temperature of the upper fixing roller does not reach 100°C within 2 min after it has exceeded 70°C   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E003-0000    The main thermistor (TH1) has poor contact or an open circuit   copyir.ocm The thermal switch (TP1) has an open circuit   copyir.ocm The fixing heater has an open circuit   copyir.ocm The AC driver is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The temperature detected by the main thermistor is 70°C for 2 sec or more after it has reached 100°C   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E004-0000    The AC driver has a short circuit   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The AC driver is found to have a short circuit (hard circuit detection)   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E005-0000    The fixing web has been taken up   copyir.ocm The fixing web length sensor (PS45) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The length of fixing web that has been taken up is in excess of the specified length   copyir.ocm
After replacing the fixing web, be sure to reset the two web counters in service mode: COPIER>COUNTER>MISC>FIX-WEB and COPIER> COUNTER>DRBL-1>FX-WEB
E010-0000    The main motor (M2) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The clock pulses do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated   copyir.ocm
E012-0000    The drum motor (M1) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG) has been generated   copyir.ocm
E013-0000    The waste toner feedscrew is faulty   copyir.ocm The water toner clock sensor (MSW2) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The rotation of the waste toner feedscrew goes out of order, and the switch (MSW2) is pressed multiple times during a specific period of time   copyir.ocm
E014-0000    The fixing motor (M19) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The motor clock signal is detected for 2 secs or more continuously after the fixing motor drive signal has been generated   copyir.ocm
E020-0000    The hopper connector is left disconnected   copyir.ocm The hopper motor (M9/M10) is faulty   copyir.ocm The toner sensor (TS1/TS2) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
During printing, the toner supply signal is '0' (absence of toner) for 2 mins   copyir.ocm
E032-0001    The copy data controller or the remote diagnostic device is faulty   copyir.ocm The Main controller PCB is faulty   copyir.ocm
Although once connected, the copy data controller or the remote diagnostic device has become disconnected   copyir.ocm
E061-0001    The laser shutter is faulty   copyir.ocm The laser unit is faulty   copyir.ocm The potential measurement PCB is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
As the result of potential control, the drum surface potential (VL2) of the white background is about 200 V (generating solid black images)   copyir.ocm
E061-0002    The laser shutter is faulty   copyir.ocm The laser unit is faulty   copyir.ocm The potential measurement PCB is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The primary charging output used for print output and the drum surface potential after laser output has been made are about 200 V (generating solid black images)   copyir.ocm
E100-0001    The BD PCB is faulty   copyir.ocm The laser unit is faulty   copyir.ocm The laser driver PCB is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC controller PCB is faulty   copyir.ocm
In 100 msec after the laser drive signal has been generated, the BD signal is not detected 50 times or more within 40 msecs   copyir.ocm
E100-0002    The BD PCB is faulty   copyir.ocm The laser unit is faulty   copyir.ocm The laser driver PCB is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the laser is on, the BD signal cycle is found to be outside a specific range 10 times or more   copyir.ocm
E110-0001    The laser scanner motor (M15) is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC controller PCB is faulty
• After the laser scanner motor drive signal has been generated, the motor ready signal (LMRDY*) does not arrive for 15 secs or more   copyir.ocm (stop - full speed, half-speed - full speed) • During the period of 'full speed ® half speed', the motor ready signal does not arrive for 60 secs or more after the speed change signal has been generated   copyir.ocm • During the period of 'full speed rotation', the motor ready signal is not detected 50 times or more (t intervals of 100 msec)   copyir.ocm
E121-0001    The controller cooling fan (FM4) is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC controller PCB is faulty   copyir.ocm
Although the controller cooling fan (FM4) is being driven, the clock signal (FM4CLK) does not arrive for 5 secs or more   copyir.ocm
E196    The EEPROM on the DC controller PCB is faulty   copyir.ocm The location of the EEPROM is wrong   copyir.ocm The DC controller PCB is faulty   copyir.ocm
1abb: When data is written to the EEPROM, the data written and the data read do not match   copyir.ocm 2abb: When the ID read into the EEPROM and the ID into the ROM are compared, a mismatch is found   copyir.ocm 3abb: When ID in the EEPROM and the ID in the ROM are compared after the main power switch is turned on, a mismatch is found   copyir.ocm a: chip Nos   copyir.ocm 0 through 5 (0: IC104, 1: IC105, 2: IC109, 3: IC110, 4: IC127, 5: IC130) bb: chip faulty address (bit)
E202-0001    The scanner HP sensor (PS39) is faulty   copyir.ocm The scanner motor (M3) is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The scanner HP sensor does not turn off even when the scanner has been moved 40 mm forward after the main power switch has been turned on or the Start key has been pressed   copyir.ocm
E202-0002    The scanner HP sensor (PS39) is faulty   copyir.ocm The scanner motor (M3) is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The scanner HP sensor does not turn on even when the scanner has been moved 450 mm in reverse   copyir.ocm
E204-0001    The ADF controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
During printing, the image leading edge signal does not arrive from the ADF   copyir.ocm
E220-0001    The lamp inverter PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The lamp inverter PCB is found to have a fault   copyir.ocm
E225-0000    The scanning lamp (xenon tube) is faulty   copyir.ocm The inverter PCB is faulty   copyir.ocm The CCD/AP PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
A specific signal level cannot be attained by CCD gain correction at power-on   copyir.ocm
E225-0002    The scanning lamp (xenon tube) is faulty   copyir.ocm The inverter PCB is faulty   copyir.ocm The CCD/AP PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The edge gain correction value changed more than a specific level compared with the correction value used for the preceding sheet   copyir.ocm
E240-0000    The main controller PCB   copyir.ocm The DC controller PCB is faulty   copyir.ocm
An error has occurred in the communication between the main controller PCB and the CPU of the DC controller PCB   copyir.ocm
E240-010B    The main controller PCB   copyir.ocm The DC controller PCB is faulty   copyir.ocm
An error occurred in the sequence during printing   copyir.ocm
E243-0000    The control panel CPU PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB   copyir.ocm
E248-0001    The EEPROM on the reader controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The ID read into the EEPROM when the main power switch has been turned on and the ID in the ROM do not match   copyir.ocm
E248-0002    The EEPROM on the reader controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
When data is written into EEPROM, the data written and the data read do not match   copyir.ocm
E248-0003    The EEPROM on the reader controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
When data is written, the ID in the EEPROM and the ID in the ROM are found not to match   copyir.ocm
E302-0001    The CCD/AP PCB is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The reader controller PCB is faulty   copyir.ocm
During shading, the reader controller PCB does not end shading in 1 sec   copyir.ocm
E302-0002    The CCD/AP PCB is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The reader controller PCB is faulty   copyir.ocm
In stream reading, the edge white accumulation (processing) does not end after a period of 10 secs   copyir.ocm
E315-0007    Main controller PCB, Hard disk drive
When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec   copyir.ocm
E315-0010    Main controller PCB, Hard disk drive
When a start command is sent to the compression/extension element of the main controller at time of decoding, an end interrupt does not occur after 4 sec   copyir.ocm
E412-0001    The cooling fan (FM1) is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm
While the cooling fan is being driven, the lock signal (FMLCK) arrives for 100 msec or more   copyir.ocm
E420-0001    The EEPROM is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm
When the host machine's power switch is turned on, the backup data of the EEPROM cannot be read or the data, if read, has an error   copyir.ocm
E421-0001    The EEPROM is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm
Backup data cannot be written to the EEPROM or the data, if written, has an error   copyir.ocm
E422-0001    The IPC communication has an error   copyir.ocm The communication line has an open circuit   copyir.ocm The ADF controller PCB is faulty   copyir.ocm
While the machine is in standby, the communication with the host machine has been interrupted for 5 secs or more   copyir.ocm or, while the machine is in operation, the communication with the host machine has been interrupted for 0   copyir.ocm5 sec or more   copyir.ocm
E500-0001    The finisher controller PCB is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine   copyir.ocm
E503-0002    The saddle stitcher controller PCB is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The communication between the saddle stitcher controller PCB and the finisher controller PCB has been interrupted   copyir.ocm
E504-0001    The height sensor (PS1) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
Communication between the height sensor and the finisher controller PCB is not possible, or communication data has an error   copyir.ocm
E504-0002    The height sensor (PS1) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
Communication between the height sensor and the finisher controller PCB is not possible for a specific period of time   copyir.ocm
E504-0003    The height sensor (PS1) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
At time of power-on, the connector of the height sensor is found to be disconnected   copyir.ocm
E504-0004    The height sensor (PS1) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
When the height sensor is being adjusted using the DIP switch, an error occurred during the adjustment   copyir.ocm
E505-0001    The EEPROM is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm The puncher driver PCB is faulty   copyir.ocm
When the power switch is turned on, the check sum of the EEPROM on the finisher controller PCB is found to have an error   copyir.ocm
E505-0002    The EEPROM is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm The puncher driver PCB is faulty   copyir.ocm
When the power switch is turned on, the check sum of the EEPROM on the puncher driver PCB is found to have an error   copyir.ocm
E512-0001    The delivery motor clock sensor (PI10) is faulty   copyir.ocm The delivery motor (M2) is faulty   copyir.ocm The finisher controller PCB is faulty
When operation starts, as many clocks as needed do not arrive from the delivery motor clock sensor   copyir.ocm
E512-0002    The delivery motor clock sensor (PI10) is faulty   copyir.ocm The delivery motor (M2) is faulty   copyir.ocm The finisher controller PCB is faulty
No clock pulse arrives while paper is being moved over a distance of 200 mm   copyir.ocm
E530-0001    The alignment plate home position sensor (PI6) is faulty   copyir.ocm The alignment motor (M3) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The alignment plate does not leave home position when the alignment motor has been driven for 2 secs   copyir.ocm
E530-0002    The alignment plate home position sensor (PI6) is faulty   copyir.ocm The alignment motor (M3) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The alignment plate does not return to home position when the alignment motor has been driven for 2 secs   copyir.ocm
E531-0001    The stapler home position detecting switch (MS7) is faulty   copyir.ocm The stapler motor (M6) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The stapler does not leave home position when the stapler motor has been driven for 0   copyir.ocm5 sec   copyir.ocm
E531-0002    The stapler home position detecting switch (MS7) is faulty   copyir.ocm The stapler motor (M6) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The stapler does not return to home position when the stapler motor has been driven for 0   copyir.ocm5 sec   copyir.ocm
E532-0001    The stapler shift home position sensor (PI7) is faulty   copyir.ocm The stapler shift motor (M4) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The stapler unit does not leave home position when the stapler shift motor has been driven for 4 secs   copyir.ocm
E532-0002    The stapler shift home position sensor (PI7) is faulty   copyir.ocm The stapler shift motor (M4) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The stapler unit does not return to home position when the stapler shift motor has been driven for 4 secs   copyir.ocm
E535-0001    The swing motor clock sensor (PI20) is faulty   copyir.ocm The swing guide open sensor (PI18) is faulty   copyir.ocm The safety area switch (MS3) is faulty   copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty   copyir.ocm The swing motor (M7) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The swing guide closed detecting switch 2 does not turn on when the swing motor has been rotated CCW for 1 sec   copyir.ocm
E535-0002    The swing motor clock sensor (PI20) is faulty   copyir.ocm The swing guide open sensor (PI18) is faulty   copyir.ocm The safety area switch (MS3) is faulty   copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty   copyir.ocm The swing motor (M7) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
While the tray is moving up, the tray upper limit detection switch is found to be on   copyir.ocm
E535-0003    The swing motor clock sensor (PI20) is faulty   copyir.ocm The swing guide open sensor (PI18) is faulty   copyir.ocm The safety area switch (MS3) is faulty   copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty   copyir.ocm The swing motor (M7) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
When the tray lift motor is driven, clock pulses do not arrive from the clock sensor 1/2 for 200 msecs   copyir.ocm
E584-0001    The shutter open sensor (PI5) is faulty   copyir.ocm The safety area detecting switch (MS3) is faulty   copyir.ocm The shutter closed detecting switch (MS4) is faulty   copyir.ocm The No   copyir.ocm 2 feed motor (M8) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The shutter closed detecting switch does not turn on when the No   copyir.ocm 2 feed motor has been rotated CCW for 1 sec or more
E584-0002    The shutter open sensor (PI5) is faulty   copyir.ocm The safety area detecting switch (MS3) is faulty   copyir.ocm The shutter closed detecting switch (MS4) is faulty   copyir.ocm The No   copyir.ocm 2 feed motor (M8) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
The shutter open sensor does not turn on when the No   copyir.ocm 2 feed motor has been rotated CCW for 1 sec   copyir.ocm
E584-0003    The shutter open sensor (PI5) is faulty   copyir.ocm The safety area detecting switch (MS3) is faulty   copyir.ocm The shutter closed detecting switch (MS4) is faulty   copyir.ocm The No   copyir.ocm 2 feed motor (M8) is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
While the tray lift motor is in operation, the shutter closed detecting switch is found to be off when the tray 1/2 is at OFF position of the safety area detecting switch   copyir.ocm
E590-0001    The punch home position sensor (PI3P) is faulty   copyir.ocm The punch motor (M1P) is faulty   copyir.ocm The punch driver PCB is faulty   copyir.ocm
The puncher does not leave home position when the punch motor has been driven for 200 msecs   copyir.ocm
E590-0002    The punch home position sensor (PI3P) is faulty   copyir.ocm The punch motor (M1P) is faulty   copyir.ocm The punch driver PCB is faulty   copyir.ocm
The puncher does not return to home position when the punch motor has been driven for 200 msecs   copyir.ocm
E593-0001    The horizontal registration home position sensor (PI1P) is faulty   copyir.ocm The horizontal registration motor (M1P) is faulty   copyir.ocm The punch driver PCB is faulty   copyir.ocm
The puncher does not leave home position when the horizontal registration motor has been driven for 4 secs   copyir.ocm
E593-0002    The horizontal registration home position sensor (PI1P) is faulty   copyir.ocm The horizontal registration motor (M1P) is faulty   copyir.ocm The punch driver PCB is faulty   copyir.ocm
The puncher does not return to home position when the horizontal registration motor has been driven for 4 secs   copyir.ocm
E5F0-0001    The paper positioning plate home position sensor (PI7S) is faulty   copyir.ocm The paper positioning plate motor (M4S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for about 1   copyir.ocm3 secs   copyir.ocm
E5F0-0002    The paper positioning plate home position sensor (PI7S) is faulty   copyir.ocm The paper positioning plate motor (M4S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper positioning plate home position sensor does not turn off 1 sec after the paper positioning plate motor has been driven for 1 sec   copyir.ocm
E5F1-0001    The folding motor clock sensor (PI4S) is faulty   copyir.ocm The paper folding home position sensor (PI21S) is faulty   copyir.ocm The folding motor (M2S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The number of detection pulses of the folding motor clock sensor drops below a specific value   copyir.ocm
E5F1-0002    The folding motor clock sensor (PI4S) is faulty   copyir.ocm The paper folding home position sensor (PI21S) is faulty   copyir.ocm The folding motor (M2S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The state of the paper folding home position sensor does not change when the folding motor has been driven for 3 secs   copyir.ocm
E5F2-0001    The guide home position sensor (PI13S) is faulty   copyir.ocm The guide motor (M3S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The guide home position sensor does not turn on when the guide motor has been driven for about 0   copyir.ocm5 sec   copyir.ocm
E5F2-0002    The guide home position sensor (PI13S) is faulty   copyir.ocm The guide motor (M3S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The guide home position sensor does not turn off when the guide motor has been driven for 1 sec   copyir.ocm
E5F3-0001    The alignment home position sensor (PI5S) is faulty   copyir.ocm The alignment motor (M5S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0   copyir.ocm5 sec (initially, driven for about 1   copyir.ocm7 sec)   copyir.ocm
E5F3-0002    The alignment home position sensor (PI5S) is faulty   copyir.ocm The alignment motor (M5S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec   copyir.ocm
E5F4-0001    The stitch home position sensor (rear, MS5S) is faulty   copyir.ocm The stitch motor (rear, M6S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The stitcher home position sensor (rear) does not turn off when the stitch motor (rear) has been rotated CW for 0   copyir.ocm5 sec or more   copyir.ocmfaulty   copyir.ocm
E5F4-0002    The stitch home position sensor (rear, MS5S) is faulty   copyir.ocm The stitch motor (rear, M6S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The stitch home position sensor (rear) does not turn on when the stitch motor (rear) has been rotated CCW for 0   copyir.ocm5 sec or more   copyir.ocm
E5F5-0001    The stitch home position senor (front, MS7S) is faulty   copyir.ocm The stitch motor (front, M7S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The stitch home position sensor (front) does not turn off when the stitch motor (front) has been rotated CW for 0   copyir.ocm5 sec or more   copyir.ocm
E5F5-0002    The stitch home position senor (front, MS7S) is faulty   copyir.ocm The stitch motor (front, M7S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The stitch home position sensor (front) does not turn on when the stitch motor (front) has been rotated CCW for 0   copyir.ocm5 sec or more   copyir.ocm
E5F6-0001    The paper push-on plate motor clock sensor (PI1S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate motor (M8S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper push-on plate home position sensor does not turn on when the paper push-on plate motor has been driven for 0   copyir.ocm3 sec or more   copyir.ocm
E5F6-0002    The paper push-on plate motor clock sensor (PI1S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate motor (M8S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper push-on plate home position sensor does not turn off when the paper push-on plate motor has been driven for 0   copyir.ocm3 sec or more   copyir.ocm
E5F6-0003    The paper push-on plate motor clock sensor (PI1S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate motor (M8S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper push-on plate leading edge position sensor does not turn off when the paper push-on plate motor has been driven for 0   copyir.ocm3 sec or more   copyir.ocm
E5F6-0004    The paper push-on plate motor clock sensor (PI1S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate motor (M8S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The number of detection pulses of the paper push-on plate motor clock sensor drops below a specific value   copyir.ocm
E5F6-0005    The paper push-on plate motor clock sensor (PI1S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate motor (M8S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The paper push-on plate leading edge sensor does not turn on when the paper push-on plate motor has been driven for 0   copyir.ocm3 sec or morere   copyir.ocm
E5F8-0001    The guide home position sensor (PI13S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The connector of the guide home position sensor is found to be disconnected   copyir.ocm
E5F8-0002    The guide home position sensor (PI13S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The connector of the paper home positioning plate home position sensor is found to be disconnected   copyir.ocm
E5F8-0003    The guide home position sensor (PI13S) is faulty   copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty   copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty   copyir.ocm The saddle stitcher controller PCB is faulty   copyir.ocm
The connector of the paper push-on plate leading edge position sensor is found to be discontented   copyir.ocm
E5F9-0001    The inlet cover switch (MS1S) is faulty   copyir.ocm The front cover switch (MS2S) is faulty   copyir.ocm The delivery cover switch (MS3S) is faulty   copyir.ocm The saddle stitch controller PCB is faulty   copyir.ocm
When the inlet cover, front cover, and the delivery cover are found to be closed, the inlet cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing   copyir.ocm
E5F9-0002    The inlet cover switch (MS1S) is faulty   copyir.ocm The front cover switch (MS2S) is faulty   copyir.ocm The delivery cover switch (MS3S) is faulty   copyir.ocm The saddle stitch controller PCB is faulty   copyir.ocm
When the inlet cover, front cover, and delivery cover are found to be closed, the front cover switch detects an open condition for 1 sec or more after the start of the initial rotation of the host machine or the start of printing   copyir.ocm
E5F9-0003    The inlet cover switch (MS1S) is faulty   copyir.ocm The front cover switch (MS2S) is faulty   copyir.ocm The delivery cover switch (MS3S) is faulty   copyir.ocm The saddle stitch controller PCB is faulty   copyir.ocm
When the inlet cover, front cover, and delivery cover are found to be closed, the delivery cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing   copyir.ocm
E601-0000    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
The main controller PCB has detected an error in control data while an image was transmitted between the main controller PCB and the hard disk drive   copyir.ocm
E601-0001    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
The main controller PCB has found an error in the control data in transfer of images between main controller PCB and the DC controller PCB   copyir.ocm
E602-0001    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
A mount error was detected when the hard disk was started up from the boot ROM   copyir.ocm
E602-0002    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
A data read error (from the hard disk) was detected when the hard disk was started from the boot ROM   copyir.ocm
E602-0003    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
A a sector error is found on the hard disk   copyir.ocm
E602-0004    The wiring is faulty (short circuit, open circuit)   copyir.ocm The hard disk drive is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
A an error is found in the read/write address for the hard disk   copyir.ocm
E607-0000    The hard disk fan (FM7) is faulty   copyir.ocm The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the hard disk fan (FM7) is being driven, the clock signal (FM7CLK) does not arrive for 5 secs or more   copyir.ocm
E677-0001    The various printer board (accessories) are faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
An error has occurred in the communication between the various printer boards (accessories) and the main controller PCB   copyir.ocm
E710-0001    The DC controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
When the main power is turned on, the IPC (IC5021) on the reader controller PCB cannot be initialized   copyir.ocm
E710-0002    The DC controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
When the main power is turned on, the IPC (IC120) on the DC controller PCB cannot be initialized   copyir.ocm
E710-0003    The DC controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
When the main power is turned on, the IPC (IC1003) on the main controller PCB cannot be initialized   copyir.ocm
E711-0001    The connector is not connected properly   copyir.ocm The remote diagnostic device PCB is faulty   copyir.ocm The copy data controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
Data has been written to the error register of the IPC (IC5021) on the reader controller PCB four times or more within 1   copyir.ocm5 secs   copyir.ocm
E711-0002    The connector is not connected properly   copyir.ocm The remote diagnostic device PCB is faulty   copyir.ocm The copy data controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
Data has been written to the error register of the IPC (IC120) on the DC controller PCB four times or more within 2 secs   copyir.ocm
E711-0003    The connector is not connected properly   copyir.ocm The remote diagnostic device PCB is faulty   copyir.ocm The copy data controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm
Data has been written to the error register of the IPC (IC1003) of the main controller PCB four times or more within 2 secs   copyir.ocm
E712-0001    The connector is not connected properly   copyir.ocm The ADF 24-V power supply is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
Communication does not resume in 3 secs after data has been written to the error register of the communication IC (IPC) of the ADF controller PCB   copyir.ocm
E712-0002    The connector is not connected properly   copyir.ocm The ADF 24-V power supply is faulty   copyir.ocm The ADF controller PCB is faulty   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The transmission bit is not enabled after a period of 10 sec at the sync register of the IPC (IC5021) on the reader controller PCB   copyir.ocm
E713-0000    The connector is not connected properly   copyir.ocm The finisher accessories power supply PCB is faulty   copyir.ocm The finisher controller PCB is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The communications IC (IPC) on the finisher controller has gone out of order   copyir.ocm
E717-0001    The wiring is faulty (short circuit, open circuit)   copyir.ocm The copy data controller or the remote diagnostic device is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
The copy data controller or the NE controller is out of order or an open circuit has been detected   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E719-0001    The wiring is faulty (short circuit, open circuit)   copyir.ocm The coin vendor is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
The communication between the coin vendor and the main controller PCB has been interrupted   copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR)   copyir.ocm
E732-0001    The connector has poor contact   copyir.ocm The reader controller PCB is faulty   copyir.ocm
The main controller PCB has detected an error in the communication between the reader controller PCB and the main controller PCB   copyir.ocm
E732-9999    The connector has poor contact   copyir.ocm The reader controller PCB is faulty   copyir.ocm
In a printer mode, a read unit is detected by the main controller PCB   copyir.ocm
E733-0001    The connector has poor contact   copyir.ocm The DC controller PCB is faulty   copyir.ocm
The main controller PCB has detected an error in the communication between the DC controller PCB and the main controller PCB   copyir.ocm
E740-0001    The LAN card is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
An error is detected on the LAN card at power-on (with the card inserted)   copyir.ocm
E740-0002    The LAN card is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
A MAC address is found to be faulty   copyir.ocm
E740-0003    The LAN card is faulty   copyir.ocm The main controller PCB is faulty   copyir.ocm
The LAN card register cannot be read   copyir.ocm
E741-0000    The PCI bus connection is not proper   copyir.ocm The main controller PCB is faulty   copyir.ocm
An error has occurred in the PCI bus   copyir.ocm
E743-0000    The connector has poor contact   copyir.ocm The main controller PCB is faulty   copyir.ocm
The reader controller PCB has detected an error in the communication between the main controller PCB and the reader controller PCB   copyir.ocm
E744-0001    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file and the main controller have a version mismatch
E744-0002    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is found to be too large   copyir.ocm
E744-0003    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is absent   copyir.ocm
E744-0004    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file cannot be read   copyir.ocm
E744-1000    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the bottom ROM product name is found to be a mismatch
E744-2000    The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the serial number of the serial number PCB is an undefined code   copyir.ocm
E804-0000    The wiring is faulty (short circuit, open circuit)   copyir.ocm The DC power supply fan (FM6) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the DC power supply fan is being driven, the clock signal (FM6CLK) does not arrive for 5 secs or more   copyir.ocm
E805-0001    The wiring is faulty (short circuit, open circuit)   copyir.ocm The feed fan (FM1) is faulty   copyir.ocm The heat discharge fan (FM3) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the heat discharge fan is being driven, the clock signal (FM3CLK) does not arrive for 5 secs or more   copyir.ocm
E805-0002    The wiring is faulty (short circuit, open circuit)   copyir.ocm The feed fan (FM1) is faulty   copyir.ocm The heat discharge fan (FM3) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the feed fan is being driven, the clock signal (FM1CLK) does not arrive for 5 secs or more   copyir.ocm
E824-0000    The wiring is faulty (short circuit, open circuit)   copyir.ocm The primary charging assembly cooling fan (FM2) is faulty   copyir.ocm The DC controller PCB is faulty   copyir.ocm
While the primary charging assembly cooling fan is being driven, the clock signal (FM2CLK) does not arrive for 5 secs or more   copyir.ocm PCB   copyir.ocm

کانون 8500

خواندن 4131 دفعه
محتوای بیشتر در این بخش: « کانون Canon iR85 کانون Canon iR9070 »

نظرات (0)

نظر ارسال شده‌ی جدیدی وجود ندارد

دیدگاه خود را بیان کنید

  1. ارسال دیدگاه بعنوان یک مهمان -
پیوست ها (0 / 3)
اشتراک‌گذاری موقعیت مکانی شما

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب