E000-000 The main thermistor (TH1) has poor contact or an open circuit copyir.ocm The thermal switch (TP1) has an open circuit copyir.ocm The fixing heater has an open circuit copyir.ocm The AC driver is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
After the main power switch is turned on, the temperature detected by the main thermistor does not reach 70°C copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E001-0001 The main thermistor (TH1) has a short circuit copyir.ocm The sub thermistor (TH2) has detected overheating copyir.ocm The AC driver is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The main thermistor or the sub thermistor has detected about 230°C or higher for 2 sec copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E001-0002 The main thermistor (TH1) has a short circuit copyir.ocm The sub thermistor (TH2) has detected overheating copyir.ocm The AC driver is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The main thermistor has detected 230°C or higher (hard circuit detection) copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E001-0003 The main thermistor (TH1) has a short circuit copyir.ocm The sub thermistor (TH2) has detected overheating copyir.ocm The AC driver is faulty copyir.ocm
The DC controller PCB is faulty copyir.ocmThe sub thermistor has detected about 236°C or higher copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E002-0000 The main thermistor (TH1) has poor contact or an open circuit copyir.ocm The thermal switch (TP1) has an open circuit copyir.ocm The AC driver is faulty copyir.ocm The DC controller is faulty copyir.ocm
The temperature of the upper fixing roller does not reach 100°C within 2 min after it has exceeded 70°C copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E003-0000 The main thermistor (TH1) has poor contact or an open circuit copyir.ocm The thermal switch (TP1) has an open circuit copyir.ocm The fixing heater has an open circuit copyir.ocm The AC driver is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The temperature detected by the main thermistor is 70°C for 2 sec or more after it has reached 100°C copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E004-0000 The AC driver has a short circuit copyir.ocm The DC controller PCB is faulty copyir.ocm
The AC driver is found to have a short circuit (hard circuit detection) copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E005-0000 The fixing web has been taken up copyir.ocm The fixing web length sensor (PS45) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The length of fixing web that has been taken up is in excess of the specified length copyir.ocm
After replacing the fixing web, be sure to reset the two web counters in service mode: COPIER>COUNTER>MISC>FIX-WEB and COPIER> COUNTER>DRBL-1>FX-WEB
E010-0000 The main motor (M2) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The clock pulses do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated copyir.ocm
E012-0000 The drum motor (M1) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG) has been generated copyir.ocm
E013-0000 The waste toner feedscrew is faulty copyir.ocm The water toner clock sensor (MSW2) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The rotation of the waste toner feedscrew goes out of order, and the switch (MSW2) is pressed multiple times during a specific period of time copyir.ocm
E014-0000 The fixing motor (M19) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The motor clock signal is detected for 2 secs or more continuously after the fixing motor drive signal has been generated copyir.ocm
E020-0000 The hopper connector is left disconnected copyir.ocm The hopper motor (M9/M10) is faulty copyir.ocm The toner sensor (TS1/TS2) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
During printing, the toner supply signal is '0' (absence of toner) for 2 mins copyir.ocm
E032-0001 The copy data controller or the remote diagnostic device is faulty copyir.ocm The Main controller PCB is faulty copyir.ocm
Although once connected, the copy data controller or the remote diagnostic device has become disconnected copyir.ocm
E061-0001 The laser shutter is faulty copyir.ocm The laser unit is faulty copyir.ocm The potential measurement PCB is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
As the result of potential control, the drum surface potential (VL2) of the white background is about 200 V (generating solid black images) copyir.ocm
E061-0002 The laser shutter is faulty copyir.ocm The laser unit is faulty copyir.ocm The potential measurement PCB is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The primary charging output used for print output and the drum surface potential after laser output has been made are about 200 V (generating solid black images) copyir.ocm
E100-0001 The BD PCB is faulty copyir.ocm The laser unit is faulty copyir.ocm The laser driver PCB is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The DC controller PCB is faulty copyir.ocm
In 100 msec after the laser drive signal has been generated, the BD signal is not detected 50 times or more within 40 msecs copyir.ocm
E100-0002 The BD PCB is faulty copyir.ocm The laser unit is faulty copyir.ocm The laser driver PCB is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The DC controller PCB is faulty copyir.ocm
While the laser is on, the BD signal cycle is found to be outside a specific range 10 times or more copyir.ocm
E110-0001 The laser scanner motor (M15) is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The DC controller PCB is faulty
• After the laser scanner motor drive signal has been generated, the motor ready signal (LMRDY*) does not arrive for 15 secs or more copyir.ocm (stop - full speed, half-speed - full speed) • During the period of 'full speed ® half speed', the motor ready signal does not arrive for 60 secs or more after the speed change signal has been generated copyir.ocm • During the period of 'full speed rotation', the motor ready signal is not detected 50 times or more (t intervals of 100 msec) copyir.ocm
E121-0001 The controller cooling fan (FM4) is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The DC controller PCB is faulty copyir.ocm
Although the controller cooling fan (FM4) is being driven, the clock signal (FM4CLK) does not arrive for 5 secs or more copyir.ocm
E196 The EEPROM on the DC controller PCB is faulty copyir.ocm The location of the EEPROM is wrong copyir.ocm The DC controller PCB is faulty copyir.ocm
1abb: When data is written to the EEPROM, the data written and the data read do not match copyir.ocm 2abb: When the ID read into the EEPROM and the ID into the ROM are compared, a mismatch is found copyir.ocm 3abb: When ID in the EEPROM and the ID in the ROM are compared after the main power switch is turned on, a mismatch is found copyir.ocm a: chip Nos copyir.ocm 0 through 5 (0: IC104, 1: IC105, 2: IC109, 3: IC110, 4: IC127, 5: IC130) bb: chip faulty address (bit)
E202-0001 The scanner HP sensor (PS39) is faulty copyir.ocm The scanner motor (M3) is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The scanner HP sensor does not turn off even when the scanner has been moved 40 mm forward after the main power switch has been turned on or the Start key has been pressed copyir.ocm
E202-0002 The scanner HP sensor (PS39) is faulty copyir.ocm The scanner motor (M3) is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The scanner HP sensor does not turn on even when the scanner has been moved 450 mm in reverse copyir.ocm
E204-0001 The ADF controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
During printing, the image leading edge signal does not arrive from the ADF copyir.ocm
E220-0001 The lamp inverter PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The lamp inverter PCB is found to have a fault copyir.ocm
E225-0000 The scanning lamp (xenon tube) is faulty copyir.ocm The inverter PCB is faulty copyir.ocm The CCD/AP PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
A specific signal level cannot be attained by CCD gain correction at power-on copyir.ocm
E225-0002 The scanning lamp (xenon tube) is faulty copyir.ocm The inverter PCB is faulty copyir.ocm The CCD/AP PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The edge gain correction value changed more than a specific level compared with the correction value used for the preceding sheet copyir.ocm
E240-0000 The main controller PCB copyir.ocm The DC controller PCB is faulty copyir.ocm
An error has occurred in the communication between the main controller PCB and the CPU of the DC controller PCB copyir.ocm
E240-010B The main controller PCB copyir.ocm The DC controller PCB is faulty copyir.ocm
An error occurred in the sequence during printing copyir.ocm
E243-0000 The control panel CPU PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB copyir.ocm
E248-0001 The EEPROM on the reader controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The ID read into the EEPROM when the main power switch has been turned on and the ID in the ROM do not match copyir.ocm
E248-0002 The EEPROM on the reader controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
When data is written into EEPROM, the data written and the data read do not match copyir.ocm
E248-0003 The EEPROM on the reader controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
When data is written, the ID in the EEPROM and the ID in the ROM are found not to match copyir.ocm
E302-0001 The CCD/AP PCB is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The reader controller PCB is faulty copyir.ocm
During shading, the reader controller PCB does not end shading in 1 sec copyir.ocm
E302-0002 The CCD/AP PCB is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The reader controller PCB is faulty copyir.ocm
In stream reading, the edge white accumulation (processing) does not end after a period of 10 secs copyir.ocm
E315-0007 Main controller PCB, Hard disk drive
When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec copyir.ocm
E315-0010 Main controller PCB, Hard disk drive
When a start command is sent to the compression/extension element of the main controller at time of decoding, an end interrupt does not occur after 4 sec copyir.ocm
E412-0001 The cooling fan (FM1) is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm
While the cooling fan is being driven, the lock signal (FMLCK) arrives for 100 msec or more copyir.ocm
E420-0001 The EEPROM is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm
When the host machine's power switch is turned on, the backup data of the EEPROM cannot be read or the data, if read, has an error copyir.ocm
E421-0001 The EEPROM is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm
Backup data cannot be written to the EEPROM or the data, if written, has an error copyir.ocm
E422-0001 The IPC communication has an error copyir.ocm The communication line has an open circuit copyir.ocm The ADF controller PCB is faulty copyir.ocm
While the machine is in standby, the communication with the host machine has been interrupted for 5 secs or more copyir.ocm or, while the machine is in operation, the communication with the host machine has been interrupted for 0 copyir.ocm5 sec or more copyir.ocm
E500-0001 The finisher controller PCB is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine copyir.ocm
E503-0002 The saddle stitcher controller PCB is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The communication between the saddle stitcher controller PCB and the finisher controller PCB has been interrupted copyir.ocm
E504-0001 The height sensor (PS1) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
Communication between the height sensor and the finisher controller PCB is not possible, or communication data has an error copyir.ocm
E504-0002 The height sensor (PS1) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
Communication between the height sensor and the finisher controller PCB is not possible for a specific period of time copyir.ocm
E504-0003 The height sensor (PS1) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
At time of power-on, the connector of the height sensor is found to be disconnected copyir.ocm
E504-0004 The height sensor (PS1) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
When the height sensor is being adjusted using the DIP switch, an error occurred during the adjustment copyir.ocm
E505-0001 The EEPROM is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm The puncher driver PCB is faulty copyir.ocm
When the power switch is turned on, the check sum of the EEPROM on the finisher controller PCB is found to have an error copyir.ocm
E505-0002 The EEPROM is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm The puncher driver PCB is faulty copyir.ocm
When the power switch is turned on, the check sum of the EEPROM on the puncher driver PCB is found to have an error copyir.ocm
E512-0001 The delivery motor clock sensor (PI10) is faulty copyir.ocm The delivery motor (M2) is faulty copyir.ocm The finisher controller PCB is faulty
When operation starts, as many clocks as needed do not arrive from the delivery motor clock sensor copyir.ocm
E512-0002 The delivery motor clock sensor (PI10) is faulty copyir.ocm The delivery motor (M2) is faulty copyir.ocm The finisher controller PCB is faulty
No clock pulse arrives while paper is being moved over a distance of 200 mm copyir.ocm
E530-0001 The alignment plate home position sensor (PI6) is faulty copyir.ocm The alignment motor (M3) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The alignment plate does not leave home position when the alignment motor has been driven for 2 secs copyir.ocm
E530-0002 The alignment plate home position sensor (PI6) is faulty copyir.ocm The alignment motor (M3) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The alignment plate does not return to home position when the alignment motor has been driven for 2 secs copyir.ocm
E531-0001 The stapler home position detecting switch (MS7) is faulty copyir.ocm The stapler motor (M6) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The stapler does not leave home position when the stapler motor has been driven for 0 copyir.ocm5 sec copyir.ocm
E531-0002 The stapler home position detecting switch (MS7) is faulty copyir.ocm The stapler motor (M6) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The stapler does not return to home position when the stapler motor has been driven for 0 copyir.ocm5 sec copyir.ocm
E532-0001 The stapler shift home position sensor (PI7) is faulty copyir.ocm The stapler shift motor (M4) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The stapler unit does not leave home position when the stapler shift motor has been driven for 4 secs copyir.ocm
E532-0002 The stapler shift home position sensor (PI7) is faulty copyir.ocm The stapler shift motor (M4) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The stapler unit does not return to home position when the stapler shift motor has been driven for 4 secs copyir.ocm
E535-0001 The swing motor clock sensor (PI20) is faulty copyir.ocm The swing guide open sensor (PI18) is faulty copyir.ocm The safety area switch (MS3) is faulty copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty copyir.ocm The swing motor (M7) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The swing guide closed detecting switch 2 does not turn on when the swing motor has been rotated CCW for 1 sec copyir.ocm
E535-0002 The swing motor clock sensor (PI20) is faulty copyir.ocm The swing guide open sensor (PI18) is faulty copyir.ocm The safety area switch (MS3) is faulty copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty copyir.ocm The swing motor (M7) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
While the tray is moving up, the tray upper limit detection switch is found to be on copyir.ocm
E535-0003 The swing motor clock sensor (PI20) is faulty copyir.ocm The swing guide open sensor (PI18) is faulty copyir.ocm The safety area switch (MS3) is faulty copyir.ocm The swing guide closed detecting switch 2 (MS6) is faulty copyir.ocm The swing motor (M7) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
When the tray lift motor is driven, clock pulses do not arrive from the clock sensor 1/2 for 200 msecs copyir.ocm
E584-0001 The shutter open sensor (PI5) is faulty copyir.ocm The safety area detecting switch (MS3) is faulty copyir.ocm The shutter closed detecting switch (MS4) is faulty copyir.ocm The No copyir.ocm 2 feed motor (M8) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The shutter closed detecting switch does not turn on when the No copyir.ocm 2 feed motor has been rotated CCW for 1 sec or more
E584-0002 The shutter open sensor (PI5) is faulty copyir.ocm The safety area detecting switch (MS3) is faulty copyir.ocm The shutter closed detecting switch (MS4) is faulty copyir.ocm The No copyir.ocm 2 feed motor (M8) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
The shutter open sensor does not turn on when the No copyir.ocm 2 feed motor has been rotated CCW for 1 sec copyir.ocm
E584-0003 The shutter open sensor (PI5) is faulty copyir.ocm The safety area detecting switch (MS3) is faulty copyir.ocm The shutter closed detecting switch (MS4) is faulty copyir.ocm The No copyir.ocm 2 feed motor (M8) is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
While the tray lift motor is in operation, the shutter closed detecting switch is found to be off when the tray 1/2 is at OFF position of the safety area detecting switch copyir.ocm
E590-0001 The punch home position sensor (PI3P) is faulty copyir.ocm The punch motor (M1P) is faulty copyir.ocm The punch driver PCB is faulty copyir.ocm
The puncher does not leave home position when the punch motor has been driven for 200 msecs copyir.ocm
E590-0002 The punch home position sensor (PI3P) is faulty copyir.ocm The punch motor (M1P) is faulty copyir.ocm The punch driver PCB is faulty copyir.ocm
The puncher does not return to home position when the punch motor has been driven for 200 msecs copyir.ocm
E593-0001 The horizontal registration home position sensor (PI1P) is faulty copyir.ocm The horizontal registration motor (M1P) is faulty copyir.ocm The punch driver PCB is faulty copyir.ocm
The puncher does not leave home position when the horizontal registration motor has been driven for 4 secs copyir.ocm
E593-0002 The horizontal registration home position sensor (PI1P) is faulty copyir.ocm The horizontal registration motor (M1P) is faulty copyir.ocm The punch driver PCB is faulty copyir.ocm
The puncher does not return to home position when the horizontal registration motor has been driven for 4 secs copyir.ocm
E5F0-0001 The paper positioning plate home position sensor (PI7S) is faulty copyir.ocm The paper positioning plate motor (M4S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for about 1 copyir.ocm3 secs copyir.ocm
E5F0-0002 The paper positioning plate home position sensor (PI7S) is faulty copyir.ocm The paper positioning plate motor (M4S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper positioning plate home position sensor does not turn off 1 sec after the paper positioning plate motor has been driven for 1 sec copyir.ocm
E5F1-0001 The folding motor clock sensor (PI4S) is faulty copyir.ocm The paper folding home position sensor (PI21S) is faulty copyir.ocm The folding motor (M2S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The number of detection pulses of the folding motor clock sensor drops below a specific value copyir.ocm
E5F1-0002 The folding motor clock sensor (PI4S) is faulty copyir.ocm The paper folding home position sensor (PI21S) is faulty copyir.ocm The folding motor (M2S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The state of the paper folding home position sensor does not change when the folding motor has been driven for 3 secs copyir.ocm
E5F2-0001 The guide home position sensor (PI13S) is faulty copyir.ocm The guide motor (M3S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The guide home position sensor does not turn on when the guide motor has been driven for about 0 copyir.ocm5 sec copyir.ocm
E5F2-0002 The guide home position sensor (PI13S) is faulty copyir.ocm The guide motor (M3S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The guide home position sensor does not turn off when the guide motor has been driven for 1 sec copyir.ocm
E5F3-0001 The alignment home position sensor (PI5S) is faulty copyir.ocm The alignment motor (M5S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0 copyir.ocm5 sec (initially, driven for about 1 copyir.ocm7 sec) copyir.ocm
E5F3-0002 The alignment home position sensor (PI5S) is faulty copyir.ocm The alignment motor (M5S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec copyir.ocm
E5F4-0001 The stitch home position sensor (rear, MS5S) is faulty copyir.ocm The stitch motor (rear, M6S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The stitcher home position sensor (rear) does not turn off when the stitch motor (rear) has been rotated CW for 0 copyir.ocm5 sec or more copyir.ocmfaulty copyir.ocm
E5F4-0002 The stitch home position sensor (rear, MS5S) is faulty copyir.ocm The stitch motor (rear, M6S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The stitch home position sensor (rear) does not turn on when the stitch motor (rear) has been rotated CCW for 0 copyir.ocm5 sec or more copyir.ocm
E5F5-0001 The stitch home position senor (front, MS7S) is faulty copyir.ocm The stitch motor (front, M7S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The stitch home position sensor (front) does not turn off when the stitch motor (front) has been rotated CW for 0 copyir.ocm5 sec or more copyir.ocm
E5F5-0002 The stitch home position senor (front, MS7S) is faulty copyir.ocm The stitch motor (front, M7S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The stitch home position sensor (front) does not turn on when the stitch motor (front) has been rotated CCW for 0 copyir.ocm5 sec or more copyir.ocm
E5F6-0001 The paper push-on plate motor clock sensor (PI1S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate motor (M8S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper push-on plate home position sensor does not turn on when the paper push-on plate motor has been driven for 0 copyir.ocm3 sec or more copyir.ocm
E5F6-0002 The paper push-on plate motor clock sensor (PI1S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate motor (M8S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper push-on plate home position sensor does not turn off when the paper push-on plate motor has been driven for 0 copyir.ocm3 sec or more copyir.ocm
E5F6-0003 The paper push-on plate motor clock sensor (PI1S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate motor (M8S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper push-on plate leading edge position sensor does not turn off when the paper push-on plate motor has been driven for 0 copyir.ocm3 sec or more copyir.ocm
E5F6-0004 The paper push-on plate motor clock sensor (PI1S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate motor (M8S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The number of detection pulses of the paper push-on plate motor clock sensor drops below a specific value copyir.ocm
E5F6-0005 The paper push-on plate motor clock sensor (PI1S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate motor (M8S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The paper push-on plate leading edge sensor does not turn on when the paper push-on plate motor has been driven for 0 copyir.ocm3 sec or morere copyir.ocm
E5F8-0001 The guide home position sensor (PI13S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The connector of the guide home position sensor is found to be disconnected copyir.ocm
E5F8-0002 The guide home position sensor (PI13S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The connector of the paper home positioning plate home position sensor is found to be disconnected copyir.ocm
E5F8-0003 The guide home position sensor (PI13S) is faulty copyir.ocm The paper push-on plate home position sensor (PI14S) is faulty copyir.ocm The paper push-on plate leading edge position sensor (PI15S) is faulty copyir.ocm The saddle stitcher controller PCB is faulty copyir.ocm
The connector of the paper push-on plate leading edge position sensor is found to be discontented copyir.ocm
E5F9-0001 The inlet cover switch (MS1S) is faulty copyir.ocm The front cover switch (MS2S) is faulty copyir.ocm The delivery cover switch (MS3S) is faulty copyir.ocm The saddle stitch controller PCB is faulty copyir.ocm
When the inlet cover, front cover, and the delivery cover are found to be closed, the inlet cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing copyir.ocm
E5F9-0002 The inlet cover switch (MS1S) is faulty copyir.ocm The front cover switch (MS2S) is faulty copyir.ocm The delivery cover switch (MS3S) is faulty copyir.ocm The saddle stitch controller PCB is faulty copyir.ocm
When the inlet cover, front cover, and delivery cover are found to be closed, the front cover switch detects an open condition for 1 sec or more after the start of the initial rotation of the host machine or the start of printing copyir.ocm
E5F9-0003 The inlet cover switch (MS1S) is faulty copyir.ocm The front cover switch (MS2S) is faulty copyir.ocm The delivery cover switch (MS3S) is faulty copyir.ocm The saddle stitch controller PCB is faulty copyir.ocm
When the inlet cover, front cover, and delivery cover are found to be closed, the delivery cover switch detects an open condition for 1 sec or more from the start of the initial rotation of the host machine or the start of printing copyir.ocm
E601-0000 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
The main controller PCB has detected an error in control data while an image was transmitted between the main controller PCB and the hard disk drive copyir.ocm
E601-0001 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
The main controller PCB has found an error in the control data in transfer of images between main controller PCB and the DC controller PCB copyir.ocm
E602-0001 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
A mount error was detected when the hard disk was started up from the boot ROM copyir.ocm
E602-0002 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
A data read error (from the hard disk) was detected when the hard disk was started from the boot ROM copyir.ocm
E602-0003 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
A a sector error is found on the hard disk copyir.ocm
E602-0004 The wiring is faulty (short circuit, open circuit) copyir.ocm The hard disk drive is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
A an error is found in the read/write address for the hard disk copyir.ocm
E607-0000 The hard disk fan (FM7) is faulty copyir.ocm The wiring is faulty (short circuit, open circuit) copyir.ocm The DC controller PCB is faulty copyir.ocm
While the hard disk fan (FM7) is being driven, the clock signal (FM7CLK) does not arrive for 5 secs or more copyir.ocm
E677-0001 The various printer board (accessories) are faulty copyir.ocm The main controller PCB is faulty copyir.ocm
An error has occurred in the communication between the various printer boards (accessories) and the main controller PCB copyir.ocm
E710-0001 The DC controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
When the main power is turned on, the IPC (IC5021) on the reader controller PCB cannot be initialized copyir.ocm
E710-0002 The DC controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
When the main power is turned on, the IPC (IC120) on the DC controller PCB cannot be initialized copyir.ocm
E710-0003 The DC controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
When the main power is turned on, the IPC (IC1003) on the main controller PCB cannot be initialized copyir.ocm
E711-0001 The connector is not connected properly copyir.ocm The remote diagnostic device PCB is faulty copyir.ocm The copy data controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
Data has been written to the error register of the IPC (IC5021) on the reader controller PCB four times or more within 1 copyir.ocm5 secs copyir.ocm
E711-0002 The connector is not connected properly copyir.ocm The remote diagnostic device PCB is faulty copyir.ocm The copy data controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
Data has been written to the error register of the IPC (IC120) on the DC controller PCB four times or more within 2 secs copyir.ocm
E711-0003 The connector is not connected properly copyir.ocm The remote diagnostic device PCB is faulty copyir.ocm The copy data controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm
Data has been written to the error register of the IPC (IC1003) of the main controller PCB four times or more within 2 secs copyir.ocm
E712-0001 The connector is not connected properly copyir.ocm The ADF 24-V power supply is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
Communication does not resume in 3 secs after data has been written to the error register of the communication IC (IPC) of the ADF controller PCB copyir.ocm
E712-0002 The connector is not connected properly copyir.ocm The ADF 24-V power supply is faulty copyir.ocm The ADF controller PCB is faulty copyir.ocm The reader controller PCB is faulty copyir.ocm
The transmission bit is not enabled after a period of 10 sec at the sync register of the IPC (IC5021) on the reader controller PCB copyir.ocm
E713-0000 The connector is not connected properly copyir.ocm The finisher accessories power supply PCB is faulty copyir.ocm The finisher controller PCB is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
The communications IC (IPC) on the finisher controller has gone out of order copyir.ocm
E717-0001 The wiring is faulty (short circuit, open circuit) copyir.ocm The copy data controller or the remote diagnostic device is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
The copy data controller or the NE controller is out of order or an open circuit has been detected copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E719-0001 The wiring is faulty (short circuit, open circuit) copyir.ocm The coin vendor is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
The communication between the coin vendor and the main controller PCB has been interrupted copyir.ocm
The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR) copyir.ocm
E732-0001 The connector has poor contact copyir.ocm The reader controller PCB is faulty copyir.ocm
The main controller PCB has detected an error in the communication between the reader controller PCB and the main controller PCB copyir.ocm
E732-9999 The connector has poor contact copyir.ocm The reader controller PCB is faulty copyir.ocm
In a printer mode, a read unit is detected by the main controller PCB copyir.ocm
E733-0001 The connector has poor contact copyir.ocm The DC controller PCB is faulty copyir.ocm
The main controller PCB has detected an error in the communication between the DC controller PCB and the main controller PCB copyir.ocm
E740-0001 The LAN card is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
An error is detected on the LAN card at power-on (with the card inserted) copyir.ocm
E740-0002 The LAN card is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
A MAC address is found to be faulty copyir.ocm
E740-0003 The LAN card is faulty copyir.ocm The main controller PCB is faulty copyir.ocm
The LAN card register cannot be read copyir.ocm
E741-0000 The PCI bus connection is not proper copyir.ocm The main controller PCB is faulty copyir.ocm
An error has occurred in the PCI bus copyir.ocm
E743-0000 The connector has poor contact copyir.ocm The main controller PCB is faulty copyir.ocm
The reader controller PCB has detected an error in the communication between the main controller PCB and the reader controller PCB copyir.ocm
E744-0001 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file and the main controller have a version mismatch
E744-0002 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is found to be too large copyir.ocm
E744-0003 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file is absent copyir.ocm
E744-0004 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the language file cannot be read copyir.ocm
E744-1000 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the bottom ROM product name is found to be a mismatch
E744-2000 The boot ROM and the firmware have a mismatch of model or type:
at time of start-up, the serial number of the serial number PCB is an undefined code copyir.ocm
E804-0000 The wiring is faulty (short circuit, open circuit) copyir.ocm The DC power supply fan (FM6) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
While the DC power supply fan is being driven, the clock signal (FM6CLK) does not arrive for 5 secs or more copyir.ocm
E805-0001 The wiring is faulty (short circuit, open circuit) copyir.ocm The feed fan (FM1) is faulty copyir.ocm The heat discharge fan (FM3) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
While the heat discharge fan is being driven, the clock signal (FM3CLK) does not arrive for 5 secs or more copyir.ocm
E805-0002 The wiring is faulty (short circuit, open circuit) copyir.ocm The feed fan (FM1) is faulty copyir.ocm The heat discharge fan (FM3) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
While the feed fan is being driven, the clock signal (FM1CLK) does not arrive for 5 secs or more copyir.ocm
E824-0000 The wiring is faulty (short circuit, open circuit) copyir.ocm The primary charging assembly cooling fan (FM2) is faulty copyir.ocm The DC controller PCB is faulty copyir.ocm
While the primary charging assembly cooling fan is being driven, the clock signal (FM2CLK) does not arrive for 5 secs or more copyir.ocm PCB copyir.ocm
کانون 8500