Your browser does not support JavaScript! > کانون Canon iRC3480i

   کانال تلگرام کپی ایران

(0) محصول
سه شنبه, 11 اسفند 1394 10:13

کانون Canon iRC3480i

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

ایرادات دستگاهای کانون براساس کد می باشد شرکت کپی ایران در نظر داردتمامی سرویس منالها و رفع ایرادادت را در اختیار شما عزیزان قرار دهد

 

E001-0000    Abnormality high temperature error of the fixing unit
Detect high temperature by the main thermistor (software)  copyir.com Software detects that the temperature detected by the main thermistor is abnormally high (above 260 deg C) for 500 ms continuously  copyir.com    Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E001-0001    Abnormality high temperature error of the fixing unit
Detect high temperature by the sub thermistor (software)  copyir.com Software detects that the temperature detected by the sub thermistor is abnormally high (above 260 deg C) for 500 ms continuously  copyir.com    Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E001-0003    Abnormality high temperature error of the fixing unit
Detect high temperature by the sub thermistor (hardware)  copyir.com Hardware detects that the temperature detected by the contact type thermistor is abnormally high (above 230 deg C)  copyir.com    Replace the fixing unit, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION> CLEAR>ERR
E003-0000    Error in the low temperature of the fixing unit
Detects the temperature detected by the main thermistor is abnormally low (below 120 deg C) for 1 sec continuously after passing 20 sec from turning ON the fixing heater  copyir.com    Check the connection of the main thermistor/thermal switch  copyir.com Check open circuit of heater  copyir.com Replace the cover switch  copyir.com Replace the fixing unit  copyir.com Replace the main power supply PCB  copyir.com Replace the DC controller PCB  copyir.com Clear the error in service mode: COPIER > FUNCTION > CLEAR > ERR  copyir.com
E003-0001    Error in the low temperature of the fixing unit
Detects the temperature detected by the sub thermistor is abnormally low (below 70 deg C) for 1 sec continuously while adjusting print temperature  copyir.com    Check on connection of the sub thermistor/thermo switch, Replace the fixing unit, Check on a break in the heater, Replace the cover switch, Replace the main power supply PCB, Replace the DC controller PCB To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E003-0002    Error in the low temperature of the fixing unit
Detects the abnormally low temperature (open circuit) when turning ON the fixing heater  copyir.com    Clear the error in service mode: COPIER > FUNCTION > CLEAR > ERR  copyir.com
E004-0000    Thermistor is not connected
During walm-up rotation, the thermistor connection signal (FUSER CNCTX) is open  copyir.com    - Confirm the cable connection - Replace the cable exchange, and established - Replace the fixing unit - Replace the DC controller PCB  copyir.com
E009-0001    Error in pressure/release of fixing film unit
In case that the output of fixing automatic pressure phase sensor is not changed although rotating/reversing the fixing motor    Check the pressure/release mechanism  copyir.com Check the connection of the connector  copyir.com Replace the motor  copyir.com
E012-0000    Drum/ITB motor error
Lock of the motor fails to be detected 3 sec or more after the motor starts to operate  copyir.com    Check on connection of the connector, Replace the motor
E013-0001    Error in the waste toner motor
Detects the fault in the waste toner motor    Replace the waste toner motor  copyir.com
E013-0002    Error in the waste toner motor
Indicates that the waste toner motor does not rotate due to the open circuit  copyir.com    Replace the waste toner motor  copyir.com Replace the DC controller PCB  copyir.com
E015-0000    Error in the registration/multifeeder motor
Indicates that the signal indicates the motor rotates with the target speed is not sent to the port after passing more than 3 sec from the startup of the motor  copyir.com    Check on connection of the connector, Replace the motor
E020-0010    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Yellow ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0011    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Magenta ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0012    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Cyan ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0013    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is higher than the upper limit of the target although setting it as the minimum when initializing Black ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0020    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Yellow ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0021    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Magenta ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0021    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Magenta ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0022    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Cyan ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0023    Error in the developing assembly (toner fault: ATR error)
Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Black ATR  copyir.com    Clean the ATR sensor window  copyir.com Check the mounting of the developing assembly  copyir.com Check the ATR sensor open circuit  copyir.com Replace the ATR sensor  copyir.com
E020-0100    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Yellow is higher than the upper limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0101    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Magenta is higher than the upper limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0102    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Cyan is higher than the upper limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0103    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Black is higher than the upper limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0200    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Yellow is lower than the lower limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0201    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Magenta is lower than the lower limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0202    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Cyan is lower than the lower limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E020-0203    Error in the developing assembly (toner fault: ATR error)
Measured density value of patch for Black is lower than the lower limit  copyir.com    Check the toner leakage from the toner buffer block within the developing assembly  copyir.com Replace the patch image reading sensor  copyir.com
E021-0000    Developing motor error
Indicates that the signal indicates the motor rotates with the target speed is not sent to the port after passing more than 3 sec from the startup of the motor  copyir.com    Check on connection of the developing motor and the DC controller PCB, Replace the DC controller PCB, Replace the developing moto
E025-0000    Error in the toner motor
Indicates an error of Y developing assembly toner supply    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0001    Error in the toner motor
Indicates an error of M developing assembly toner supply    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0002    Error in the toner motor
Indicates an error of C developing assembly toner supply    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0003    Error in the toner motor
Error of Bk developing assembly toner supply    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0100    Error in the toner motor
Y buffer supply error    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0101    Error in the toner motor
M buffer supply error    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0102    Error in the toner motor
C buffer supply error    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E025-0103    Error in the toner motor
Bk buffer supply error    Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor
E032-0001    The counter of the NE controller fails to operate  copyir.com
A break in the count pulse signal is detected  copyir.com    Check on a break in the cable
E045-0000    OHP sensor error
The sampling data measured during initial multiple rotations is lower than the specific level  copyir.com    Replace the OHP sensor
E067-0101    High voltage-related error (Primary transfer)
The first detected current of primary transfer ATVC is the threshold or more  copyir.com    Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy  copyir.com
E067-0102    High voltage-related error (Primary transfer)
The two detected currents of primary transfer ATVC are both the threshold or less  copyir.com    Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy  copyir.com
E067-0103    High voltage-related error (Primary transfer)
The two detected currents of primary transfer ATVC are the same each other  copyir.com    Check on the primary transfer roller spring, Clean the position where the primary transfer roller contacts, Replace the primary transfer roller, Replace the drum unit Check a value of COPIER> DISPLAY> MISC> DRM-LIFE, and replace the drum unit if the value is near 100 because the drum may have reached its life expectancy  copyir.com
E100-0000    BD error
Lock of the BD control fails while rotation of the polygon motor is stable  copyir.com    Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit
E110-0000    Error in polygon motor
BD control is not locked when 5 sec passed after the activation of polygon motor  copyir.com    Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit  copyir.com
E110-0001    Error in polygon motorSpeed lock of the FG speed control fails to be executed 5 sec after the polygon motor starts to operate (Does not reach the specified speed)  copyir.com    Check on connection between the laser scanner unit and the DC controller PCB, Check on 24V line fuse, Replace the laser scanner unit  copyir.com
E193-0001    Error in IMG1 (error in add-on)
Error in initialization of image ASIC of DC controller PCB (IMG)    Replace DC controller PCB
E202-0001    CIS unit HP detection error
The HP sensor fails to be ON after the CIS unit moves backward for a specific distance or more  copyir.com    Disconnect and then connect the connector, Replace the scanner HP sensor, Replace the scanner motor, Replace the reader controller PCB
E202-0002    CIS unit HP detection error
The HP sensor fails to be OFF after the CIS unit moves forward for a specific distance or more  copyir.com    Disconnect and then connect the connector, Replace the scanner HP sensor, Replace the scanner motor, Replace the reader controller PCB
E225-0001    CIS light quantity error
Normal light-up of the lamp fails to be confirmed at the time of power-on and shading correction when a job starts  copyir.com    Disconnect and then connect the connector, Replace the document lamp (xenon tube), Replace the CIS, Replace the inverter PCB, Replace the reader controller PCB  copyir.com
E227-0001    Power supply error in the reader unit
24V port is off at power-on  copyir.com    Disconnect and connect the power supply connector, Replace the power supply
E227-0002    Power supply error in the reader unit
24V port is off when a job starts  copyir.com    Disconnect and connect the power supply connector, Replace the power supply
E227-0003    Power supply error in the reader unit
24V port is off when a job terminates  copyir.com    Disconnect and connect the power supply connector, Replace the power supply
E227-0004    Power supply error in the reader unit
24V port is off during a drive under load  copyir.com    Disconnect and connect the power supply connector, Replace the power supply
E240-0000    Error in communication of controller
Error in communication data  copyir.com    Disconnect and connect the main controller PCB (sub SJ-A/ PDRM-EF-A), or replace it  copyir.com Replace the main controller PCB (main)  copyir.com
E240-0001    Error in communication of controller
There is no response when 3 sec passed since the main controller had sent the pickup request to DC controller during printing  copyir.com    Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0002    Error in communication of controller
There is no response when 4 sec passed since the main controller had sent the request for image output to DC controller during printing  copyir.com    Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0003    Error in communication of controller
The engine is activated when jam occurs  copyir.com    Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0004    Error in communication of controller
When 90 seconds pass as the pre-rotation end waiting    Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E240-0005    Error in communication of controller
When 90 seconds pass as the Dhalf beginning waiting    Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB
E243-0000    Control panel unit error
Communication between the main controller and the control panel unit is abnormal  copyir.com    Check on connection between the main controller PCB and the control panel unit
E244-0000    Error in connection of the flexible cable on the DC controller PCB
Error in connection of the flexible cable on the DC controller PCB (right side (1 pc  copyir.com))    Check the connection of the flexible cable, replace the DC controller PCB
E244-0001    Error in connection of the flexible cable on the DC controller PCB
Error in connection of the flexible cable on the DC controller PCB (left side (3 pc  copyir.com))    Check the connection of the flexible cable, replace the DC controller PCB
E248-0000    Backup memory error
Check error of the SRAM PCB (at start up)    Check on connection of the SRAM PCB, Replace the SRAM PCB
E248-0001    Backup memory error
Reader controller EEPROM error at power-on    Replace the reader controller PCB
E248-0002    Backup memory error
Reader controller EEPROM writing error    Replace the reader controller PCB
E248-0003    Backup memory error
Reader controller EEPROM reading error after check error writing    Replace the reader controller PCB
E351-0000    Main controller PCB error
Communication error of the main controller PCB occurs at start-up  copyir.com    Disconnect and connect the main controller PCB (sub SJ-A/ PDRM-EF-A/R-A), or replace it  copyir.com Replace the main controller PCB (main)  copyir.com
E400-0001    Feeder communication error
Checksum error    - Check the connection of the cable - Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E400-0002    Feeder communication error
Reception status error    - Check the connection of the cable - Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E400-0003    Feeder communication error
Reception interrupt error    - Check the connection of the cable - Check on connection between the ADF controller PCB and the main controller PCB (sub), Replace the ADF controller PCB, Replace the main controller PCB (sub
E413-0001    Pressure motor trouble
Pressure HP sensor OPEN    Replace the pressure motor  copyir.com
E413-0002    Pressure motor trouble
Pressure HP sensor CLOSE    Replace the pressure motor  copyir.com
E490-0001    Error in different feeder model
Feeder for other model is detected  copyir.com    Connect an appropriate feeder
E503-0002    Finisher internal communication error
Communication error between the finisher and the saddle unit    Check on connection between the saddle stitcher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the saddle stitcher controller PCB
E503-0003    Finisher internal communication error
Communication error between the finisher and the puncher unit    Check on connection between the saddle stitcher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the saddle stitcher controller PCB
E505-0001    Finisher backup memory error
Data stored in the backup memory is abnormal  copyir.com    Check on connection between the DC controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the DC controller PCB
E505-0002    Finisher backup memory error
Abnormality of puncher unit EEPROM data    Check on connection between the puncher controller PCB and the finisher controller PCB, Replace the finisher controller PCB, Replace the puncher controller PCB
E505-0003    Finisher backup memory error
Finisher controller EEPROM writing error    Replace the finisher controller PCB
E505-0004    Finisher backup memory error
Finisher controller EEPROM writing timeout error    Replace the finisher controller PCB
E508-0001    Error in different model
At start-up, when the pickup/delivery option for different model is detected  copyir.com    Replace to the supported pickup option (side paper deck), delivery option (finisher) for this model  copyir.com
E514-8001    Stack delivery error / End assist motor error Finisher-Z1
The HP sensor fails to be ON within 1500ms after the return belt starts to move to its HP  copyir.com    Check on a drive of the stack retaining roller, Replace the return belt U-turn HP sensor (SR5) , Replace the stack delivery motor (M2)
E514-8001    Stack delivery error / End assist motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the end assist motor rotates for a specific period of time  copyir.com    Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E514-8002    Stack delivery error / End assist motor error Finisher-Z1
The HP sensor fails to be OFF within 1500ms after the return belt starts to move to the belt contact position  copyir.com    Check on a drive of the stack retaining roller, Replace the return belt U-turn HP sensor (SR5) , Replace the stack delivery motor (M2)
E514-8002    Stack delivery error / End assist motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the end assist motor rotates for a specific period of time  copyir.com    Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E519-8001    Gear change motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the end assist motor rotates for a specific period of time  copyir.com    Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E519-8002    Gear change motor error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the end assist motor rotates for a specific period of time  copyir.com    Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)
E530-8001    Rear alignment error Finisher-Z1
The HP sensor fails to be ON within 2000ms after the rear adjuster plate starts to move to its HP  copyir.com    Replace the rear adjuster plate HP sensor (SR4) , Replace the rear adjuster plate motor (M4)
E530-8001    Front alignment error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be OFF after the front jog motor rotates for a specific period of time  copyir.com    Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33)
E530-8002    Rear alignment error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the rear adjuster plate starts to move from its HP  copyir.com    Replace the rear adjuster plate HP sensor (SR4) , Replace the rear adjuster plate motor (M4)
E537-8002    Front alignment error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the front adjuster plate starts to move from its HP  copyir.com    Replace the front adjuster plate HP sensor (SR3) , Replace the front adjuster plate motor (M3) , Replace the adjuster plate drive belt
E537-8002    Rear alignment error Finisher-Y1, Saddle Finisher-Y2
The HP sensor fails to be ON after the swing motor rotates for a specific period of time  copyir.com    Replace the rear adjuster plate HP sensor (PI37) , Replace the rear adjuster plate motor (M34)
E540-8001    Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
The upper tray up/down motor clock is abnormal  copyir.com    Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8002    Stack tray up/down error Finisher-Z1
Paper surface detection fails to end within 1000ms  copyir.com    Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E540-8002    Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
Area is abnormal  copyir.com    Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8003    Stack tray up/down error Finisher-Z1
Encoder lock within 200ms fails to reach 10pulse during paper surface detection  copyir.com    Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E540-8003    Upper tray up/down error Finisher-Y1, Saddle Finisher-Y2
The safety switch is activated  copyir.com    Replace the shift motor (M37) of the tray 1, Replace the shift area sensor PCB of the tray 1
E540-8004    Stack tray up/down error Finisher-Z1
Outputs of the top paper sensor, bottom paper sensor, tray upper limit sensor, and tray lower limit sensor have abnormality during paper surface detection  copyir.com    Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)
E542-8001    Lower tray up/down error Finisher-Z1
The lower tray up/down motor clock is abnormal  copyir.com    Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E542-8002    Lower tray up/down error Finisher-Z1
Area is abnormal  copyir.com    Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E542-8003    Lower tray up/down error Finisher-Z1
The safety switch is activated  copyir.com    Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2
E577-8001    Paddle error Finisher-Z1
The HP sensor fails to be ON within 1500ms after the paper retaining paddle starts to move to its HP  copyir.com    Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)
E577-8002    Paddle error Finisher-Z1
The HP sensor fails to be OFF within 1000ms after the paper retaining paddle starts to move from its HP  copyir.com    Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)
E584-8001    Shutter unit error Finisher-Y1, Saddle Finisher-Y2
The shutter open sensor fails to be OFF (The shutter cannot be closed)  copyir.com    Replace the stack ejection motor (M32) , Replace the shutter open/close clutch (CL31), Replace the shutter HP sensor (PI45)
E584-8002    Shutter unit error Finisher-Y1, Saddle Finisher-Y2
The shutter open sensor fails to be ON (The shutter cannot be opened)  copyir.com    Replace the stack ejection motor (M32) , Replace the shutter open/close clutch (CL31), Replace the shutter HP sensor (PI45)
E590-8001    Puncher motor error Puncher Unit
The puncher HP sensor fails to be detected after the puncher motor is driven for 200ms  copyir.com    Replace the puncher HP sensor, Replace the puncher motor
E590-8002    Puncher motor error Puncher Unit
The puncher fails to detect the puncher HP sensor after the puncher motor stops during initial operation  copyir.com    Replace the puncher HP sensor, Replace the puncher motor
E591-8001    Puncher dust sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the puncher dust sensor
E591-8002    Puncher dust sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the puncher dust sensor
E592-8001    Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the end sensor
E592-8002    Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the end sensor
E592-8003    Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the side registration sensor 1
E592-8004    Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the side registration sensor 1
E592-8005    Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the side registration sensor 2
E592-8006    Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the side registration sensor 2
E592-8007    Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the side registration sensor 3
E592-8008    Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the side registration sensor 3
E592-8009    Puncher side registration sensor error
Light receiving voltage at the time of light emission is abnormal  copyir.com    Replace the side registration sensor 4
E592-800A    Puncher side registration sensor error
Light receiving voltage at the time of non-light-emission is abnormal  copyir.com    Replace the side registration sensor 4
E593-8001    Puncher shift motor error
The HP sensor fails to be OFF  copyir.com    Replace the HP sensor, Replace the puncher shift motor
E593-8002    Puncher shift motor error
The HP sensor fails to be ON  copyir.com    Replace the HP sensor, Replace the puncher shift motor
E5F0-8001    Saddle paper positioning error
The paper positioning plate HP sensor fails to be ON after the paper positioning plate motor is driven for 1  copyir.com33 sec  copyir.com    Replace the paper positioning plate motor (M4S), Replace the paper positioning plate HP sensor (PI7S)
E5F0-8002    Saddle paper positioning error
The paper positioning plate HP sensor fails to be OFF after the paper positioning plate motor is driven for 1 sec  copyir.com    Replace the paper positioning plate motor (M4S), Replace the paper positioning plate HP sensor (PI7S)
E5F1-8001    Saddle paper folder error
The number of detection pulses for the paper folder motor clock sensor is below the specific level  copyir.com    Replace the paper folder motor (M2S), Replace the paper folder motor clock sensor (PI4S)
E5F1-8002    Saddle paper folder error
The paper folder HP sensor fails to change after the paper folder motor is driven for 3 sec  copyir.com    Replace the paper folder motor (M2S), Replace the paper folder motor clock sensor (PI4S)
E5F2-8001    Saddle guide error
The guide HP sensor fails to be ON after the guide motor is driven for 0  copyir.com455 sec  copyir.com    Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)
E5F2-8002    Saddle guide error
The HP sensor fails to be OFF after the guide motor is driven for 1 sec  copyir.com    Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)
E5F3-8001    Saddle alignment error
The adjuster plate HP sensor fails to be ON after the jog motor is driven for 0  copyir.com5 sec  copyir.com (for 1  copyir.com67 sec  copyir.com during initial operation)    Replace the jog motor (M5S), Replace the adjuster plate HP sensor (PI5S)
E5F3-8002    Saddle alignment error
The adjuster plate HP sensor fails to be OFF after the jog motor is driven for 1 sec  copyir.com    Replace the jog motor (M5S), Replace the adjuster plate HP sensor (PI5S)
E5F4-8001    Saddle rear side staple error
The stitching HP sensor fails to be ON after the stitcher motor (rear) rotates in the adverse direction for 0  copyir.com5 sec  copyir.com or more  copyir.com    Replace the stitcher motor (rear, M6S), Replace the stitching HP sensor (rear, MS5S)
E5F4-8002    Saddle rear side staple error
The stitching HP sensor fails to be OFF after the stitcher motor (rear) rotates for 0  copyir.com5 sec  copyir.com or more  copyir.com    Replace the stitcher motor (rear, M6S), Replace the stitching HP sensor (rear, MS5S)
E5F5-8001    Saddle front side staple error
The stitching HP sensor fails to be ON after the stitcher motor (front) rotates in the adverse direction for 0  copyir.com5 sec  copyir.com or more  copyir.com    Replace the stitcher motor (front, M7S), Replace the stitching HP sensor (front, MS7S)
E5F5-8002    Saddle front side staple error
The stitching HP sensor fails to be OFF after the stitcher motor (front) rotates for 0  copyir.com5 sec  copyir.com or more  copyir.com    Replace the stitcher motor (front, M7S), Replace the stitching HP sensor (front, MS7S)
E5F6-8001    Saddle paper push-on error
The paper pressure plate HP sensor fails to be ON after the paper pressure plate motor is driven for 0  copyir.com3 sec  copyir.com or more  copyir.com    Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)
E5F6-8002    Saddle paper push-on error
The paper pressure plate HP sensor fails to be OFF after the paper pressure plate motor is driven for 80ms or more  copyir.com    Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)
E5F6-8003    Saddle paper push-on error
The number of detection pulses for the paper pressure plate motor clock sensor is below the specific level  copyir.com    Replace the paper pressure plate motor (M8S), Replace the paper pressure plate motor clock sensor (PI1S)
E5F6-8004    Saddle paper push-on error
The paper pressure plate leading edge sensor fails to be OFF after the paper pressure plate motor is driven for 80ms or more  copyir.com    Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)
E5F6-8005    Saddle paper push-on error
The paper pressure plate leading edge sensor fails to be ON after the paper pressure plate motor is driven for 0  copyir.com3 sec  copyir.com or more  copyir.com    Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)
E5F8-8001    Saddle connector error
Disconnection of the guide HP sensor connector is detected  copyir.com    Disconnect and then connect the guide HP sensor (PI13S) connector
E5F8-8002    Saddle connector error
Disconnection of the paper pressure plate HP sensor connector is detected  copyir.com    Disconnect and then connect the paper pressure plate HP sensor (PI14S) connector
E5F8-8003    Saddle connector error
Disconnection of the paper pressure plate leading edge sensor connector is detected  copyir.com    Disconnect and then connect the paper pressure plate leading edge sensor (PI15S) connector
E5F9-8001    Saddle switch error
Open of the inlet cover is detected for 1 sec  copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed  copyir.com - Inlet cover sensor (PI9S) - Front cover open/close sensor (PI2S) - Delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open  copyir.com    Replace the inlet cover switch (MS1S), Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E5F9-8002    Saddle switch error
Open of the front cover switch is detected for 1 sec  copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed  copyir.com - Inlet cover sensor (PI9S) - Front cover open/close sensor (PI2S) - Delivery cover sensor (PI3S)    Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E5F9-8003    Saddle switch error
Open of the delivery cover switch is detected for 1 sec  copyir.com or more after the host machine starts initial rotation/printing while the following sensors detect their covers closed  copyir.com - Inlet cover sensor (PI9S) - Front cover open/close sensor (PI2S) - Delivery cover sensor (PI3S) - Delivery cover switch (MS3S)    Replace the inlet cover switch (MS1S), Replace the front cover switch (MS2S), Replace the delivery cover switch (MS3S)
E601-0000    Abnormality of image memory
Communication error of the image memory (SDRAM)    Replace the SDRAM
E602    Hard disk error    
E604-0000    The image memory (SDRAM) is faulty/insufficient
Memory capacity required for a model fails to be recognized  copyir.com    Add on the SDRAM
E604-0001    The image memory (SDRAM) is faulty/insufficient
Memory for MEAP application is insufficient  copyir.com    Add on the SDRAM
E604-0002    The image memory (SDRAM) is faulty/insufficient
The image memory of larger than 1  copyir.com5GB is installed (at activation)    Make the memory 1  copyir.com5GB or less  copyir.com
E604-0512    The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (512MB is required)    Add on the SDRAM
E604-0768    The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (768MB is required)    Add on the SDRAM
E604-1024    The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (1024MB is required)    Add on the SDRAM
E604-1536    The image memory (SDRAM) is faulty/insufficient
Memory is faulty/insufficient (1536MB is required)    Add on the SDRAM
E609-0008    Abnormal low temperature of the hard disk
At start-up, temperature of the HDD fails to reach the specific level within a specific period of time  copyir.com    Replace the HDD
E609-0009    Abnormal low temperature of the hard disk
During recovery from sleep mode, temperature of the HDD is below the specific level within the specific period of time  copyir.com    Replace the HDD
E610    Failure in the hard disk cryptographic key    
E611-0000    Error in repeat of reboot due to fault of SRAM, etc  copyir.com
SRAM information is broken, job information stored in SRAM cannot be read and reboot is repeated at recovery from power-off    Clear SRAM to delete the shutdown assurance job  copyir.com
E674    FAX board communication error    Check on connection between the FAX board and the main controller PCB, Replace the FAX board, Replace the main controller PCB
E677    Abnormality of the external controller    Check on connection of the cable, Re-install the external controller system  copyir.com Connect an appropriate controller, Re-install the external controller system  copyir.com Check on connection of the cable, Re-install the external controller system
E710-0000    IPC initialization error
Error in initialization of IPC chip    Check the connection of cable, Replace the DC controller PCB
E710-0001    IPC initialization error
The status fails to be ready within 3 sec after the IPC chip starts up  copyir.com    Check on connection of the cable
E711-0001    IPC communication error
Error is set to the error register of the IPC chip 4 times or more within 1  copyir.com5 sec    Check on connection of the cable, Replace the ADF controller PCB, Replace the reader controller PCB
E713-0000    Communication error between the finisher and the printer
Communication between the finisher and the copier stops  copyir.com    Check on connection of the cable, Replace the finisher controller PCB, Replace the DC controller PCB
E716-0000    Error in communication to cassette pedestal, 2 / 3 delivery unit
Error in data communication with cassette pedestal    Check cable connection, replace pedestal PCB, replace DC controller PCB
E716-0001    Error in communication to cassette pedestal, 2 / 3 delivery unit
Error in data communication with 2 / 3 delivery unit    Check cable connection, replace 2 / 3 delivery unit PCB, replace DC controller PCB
E717-0001    Communication error with the NE controller
The NE controller connected before the power is turned off fails to be recognized at power-on  copyir.com    Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E717-0002    Communication error with the NE controller
A break in the IPC, IPC communication fails to recover    Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E719    Communication error with the coin vender/card reader    Check on connection of the cable To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR
E730    PDL error    Reset PDL, Turn OFF and back ON the main power
E731    UFR PCB error    Check on connection of the UFR PCB , Replace the UFR PCB, Replace the main controller PCB
E732-0001    Reader communication error
DDI-S communication error    Check on connection between the reader controller PCB and the main controller PCB, Check on the reader power supply
E732-8888    Reader communication error
When the different scanner model is detected  copyir.com    Check the scanner model and the scan type at: COPIER > OPTION > BODY > SCAN TYPE, then make the scan type setting as below  copyir.com 0 for CIS model reader 1 for CCD model reader
E732-9999    Reader communication error
When the scanner is initially detected on a printer model (not error)  copyir.com    Main power OFF/ON
E733-0000    Printer communication error
The printer fails to be detected at start-up  copyir.com    Check on connection between the DC controller PCB and the main controller PCB, Check on the printer power supply
E733-0001    Printer communication error
Abnormality of the Ethernet board    Check on connection between the DC controller PCB and the main controller PCB, Check on the printer power supply
E740    Abnormality of the Ethernet board    Replace the Ethernet board , Replace the main controller PCB (sub LAN-bar)
E743-0000    DDI communication error (Reader side detection)
The reader controller PCB detects communication error between the main controller PCB and the reader controller PCB  copyir.com    Disconnect and then connect the reader communication cable connector, Replace the reader controller PCB, Replace the main controller PCB
E744    Language file/BootROM error    Upgrade the version of the Language file
E745    Token ring board error    Check on connection of the token ring board, Replace the token ring board
E746    Option board error    Replace with an appropriate UFR PCB  copyir.com Replace with an appropriate main controller PCB (sub)
E747    Main controller PCB error (Image processing ASIC or memory control/communication control ASIC)    Turn the main power off and turn it back on  copyir.com Disconnect and connect the main controller PCB Replace the main controller PCB (Main)  copyir.com
E748    Main controller PCB error (Image processing ASIC or memory control/communication control ASIC)    Disconnect and then connect the main controller PCB (Sub SJA/ PDRM-EF-A/RO-A), Clean the terminal, Replace the main controller PCB (Sub SJ-A/PDRM-EF-A/RO-A), Disconnect and then connect the open interface PCB, Clean the terminal, Replace the open interface PCB, Replace the main controller PCB (main)
E749    Restart in accordance with a change of the product configuration    Turn OFF and back ON the main power to recover  copyir.com Recovered by turning the main power OFF / ON
E804-0000    Controller fan error
Stop of power supply cooling fan was detected    Check the connection of power supply cooling fan, replace it
E804-0001    Controller fan error
Stop of power supply cooling fan 2 was detected    Check the connection of power supply cooling fan 2, replace it
E804-0004    Controller fan error
Stoppage of the controller fan is detected for 16 sec continuously  copyir.com    Check on connection of the controller fan, Replace the controller fan
E805-0001    Fan error
Lock fails to be detected for 5sec continuously while the exhaust fan (front) is driven  copyir.com Disconnection of the fan connector  copyir.com Lock signal fails to be sent due to a fan failure  copyir.com    Check on connection of the exhaust fan (front), Replace the exhaust fan (front)
E805-0002    Fan error
Lock fails to be detected for 5sec continuously while the exhaust fan (rear) is driven  copyir.com Disconnection of the fan connector  copyir.com Lock signal fails to be sent due to a fan failure  copyir.com    Check on connection of the exhaust fan (rear), Replace the exhaust fan (rear)
E806-0001    Error in fan of main body
Error in delivery adhesive fan was detected    Check the connection of delivery adhesive fan, replace it
E806-0002    Error in fan of main body
The drop of connector of delivery adhesive fan / the disconnection was detected    Check the connection of delivery adhesive fan, replace it
E806-0003    Error in fan of main body
Error in secondary transfer exhaust fan was detected    Check the connection of secondary transfer exhaust fan, replace it
E807-0001    Error in fan of process cartridge
Error in fan (front) of process cartridge was detected    Check the connection of fan (front) of process cartridge, replace it
E807-0002    Error in fan of process cartridge
Error in fan (rear) of process cartridge was detected    Check the connection of fan (rear) of process cartridge, replace it
E808-0000    Error in low-voltage power supply PCB (error in zero cross)
Error in low-voltage power supply PCB    Replace low-voltage power supply PCB, replace DC controller PCB
E811-0000    Error in detection of new drum unit
Error in blowout of fuse for detection of new drum unit (process cartridge)    Check the connection of drum unit, replace it Replace DC driver PCB
E811-0001    Error in detection of new drum unit
Error in blowout of fuse for detection of new drum unit (process cartridge)    Check the connection of drum unit, replace it Replace DC driver PCB
E840-0000    Fan shutter error
Fan shutter open/close operation Error Abnormal rotation of the fan shutter motor Defect of the fan shutter position sensor Defect of the fan shutter home position error Defect of the DC controller PCB    - Replace the fan shutter motor - Replace the fan shutter position sensor - Replace the fan shutter home position sensor - Replace the DC controller PCB
E990-0000    Error in the waste toner shutter
When the output of the waste toner shutter opening and shutting detection sensor doesn't become "H" when it WMUPR period after the sleep returns after eight hours or more pass, the door opening and shutting is detected or main power switch turns on  copyir.com    - Check that the drum unit is properly installed - Replace the waste toner shutter sensor

خواندن 1455 دفعه
محتوای بیشتر در این بخش: « کانون Canon iRC3480 کانونCanon iRC3580 »

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب