Your browser does not support JavaScript! > کیو سرا میتا Kyocera-Mita TASKalfa 650c

   کانال تلگرام کپی ایران

(0) محصول
یکشنبه, 19 ارديبهشت 1395 14:41

کیو سرا میتا Kyocera-Mita TASKalfa 650c

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

C021    Developer unit motor-YMC locking error: The developer unit motor-YMC is not rotating normally     copyir.com
C022    Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally
C023    Developer unit motor-K locking error: The developer unit motor-K is not rotating normally     copyir.com
C024    Developer unit mixer motor-K locking error: The developer unit mixer motor-K is not rotating normally     copyir.com
C130    1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally     copyir.com (the case that paper can be fed from any drawer except the 1st drawer)
C140    2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally     copyir.com (the case that paper can be fed from any drawer except the 2nd drawer)
C150    3rd drawer tray abnormality: The 3rd drawer tray-up motor is not rotating or the 3rd drawer tray is not moving normally     copyir.com (the case that paper can be fed from any drawer except the 3rd drawer)
C160    4th drawer tray abnormality: The 4th drawer tray-up motor is not rotating or the 4th drawer tray is not moving normally     copyir.com (the case that paper can be fed from any drawer except the 4th drawer)
C180    LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally     copyir.com (the case that paper can be fed from any drawer except the LCF)
C1A0    LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally     copyir.com (the case that paper can be fed from any drawer except the LCF)
C1C0    Option LCF tray-up motor abnormality: The option LCF tray-up motor is not moving normally
C260    Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON     copyir.com
C270    (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time     copyir.com (2) Downloading firmware with an incorrect model     copyir.com
C280    Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time     copyir.com
C360    Needle electrode cleaner operation abnormality
C370    Transfer belt operation abnormality
C380    Auto-toner sensor-K abnormality (upper limit)
C381    Auto-toner sensor-K abnormality (lower limit)
C382    Auto-toner sensor-K connection error
C390    Auto-toner sensor-C abnormality (upper limit)
C391    Auto-toner sensor-C abnormality (lower limit)
C392    Auto-toner sensor-C connection error
C3A0    Auto-toner sensor-M abnormality (upper limit)
C3A1    Auto-toner sensor-M abnormality (lower limit)
C3A2    Auto-toner sensor-M connection error
C3B0    Auto-toner sensor-Y abnormality (upper limit)
C3B1    Auto-toner sensor-Y abnormality (lower limit)
C3B2    Auto-toner sensor-Y connection error
C3C0    Process unit connection error
C411    Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON     copyir.com
C412    Thermistor/heater lamp abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser belt temperature does not rise within a specified period of time after power-ON     copyir.com
C443    Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)
C445    Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C446    Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C447    Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)
C448    Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified
C451    Thermopile and edge thermistor temperature difference
C452    Thermopile temperature difference
C461    Pressure roller heater 40°C detection (Not determined)
C462    Pressure roller heater 40°C detection (Determined)
C463    Pressure roller thermistor and edge thermistor temperature difference
C464    Pressure roller thermistor temperature difference
C465    Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C466    Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C467    Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status)
C468    Pressure roller thermistor abnormality after entering ready status (overheating)
C471    IH board initialization abnormality
C472    Power supply abnormality
C473    Surge pressure detection / power and voltage upper limit abnormality
C474    Power and voltage lower limit abnormality
C476    IH low power supply
C480    IGBT high temperature abnormality
C481    IH drive circuit abnormality
C490    IH circuit abnormality / IH coil abnormality
C4B0    Fuser unit counter abnormality
C4B1    Fuser unit voltage judgment abnormality
C4D0    Fuser belt thermopile abnormality
C4E0    Fuser unit releasing operation abnormality - Though the pressure roller is released, its position cannot be detected     copyir.com
C4E1    Fuser unit contacting operation abnormality - Though the pressure roller is contacted, its position cannot be detected     copyir.com
C4E2    Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates     copyir.com
C4E3    Fuser motor rotation abnormality
C550    RADF I/F error: Communication error has occurred between the RADF and the scanner     copyir.com
C560    Communication error between Engine-CPU and PFC board
C570    Communication error between Engine-CPU and CNV board
C580    Communication error between CNV board and finisher
C5A0    SRAM board not connected (LGC board)
C5A1    SRAM board data abnormality (LGC board)
C730    RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed     copyir.com
C880    RADF original feed motor abnormality: An error signal has been detected when the motor is rotating     copyir.com
C890    RADF read motor abnormality: An error signal has been detected when the motor is rotating     copyir.com
C8A0    RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating     copyir.com
C8B0    RADF original exit motor abnormality: An error signal has been detected when the motor is rotating     copyir.com
C8C0    RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully     copyir.com
C8E0    RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred     copyir.com
C900    Connection error between SYS board and LGC board
C940    Engine-CPU abnormality
C962    LGC board ID abnormality
C970    High-voltage transformer abnormality: Leakage of the main charger is detected     copyir.com
C9E0    Connection error between SLG board and SYS board
CA00    Image position alignment abnormality
CA10    Polygonal motor abnormality: The polygonal motor is not rotating normally
CA20    H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams     copyir.com
CA47    SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking     copyir.com
CB00    Finisher not connected: Communication error has occurred between the equipment and finisher     copyir.com [MJ1103/1104]
CB01    Finisher communication error: Communication error has occurred between the equipment and finisher     copyir.com [MJ-1103/1104]
CB10    Entrance motor abnormality: The entrance motor is not rotating normally     copyir.com [MJ-1103/1104]
CB11    Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally     copyir.com [MJ-1103/1104]
CB12    Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally     copyir.com [MJ-1103/1104]
CB13    Finisher exit motor abnormality
CB14    Paper holding arm motor abnormality
CB30    Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally     copyir.com [MJ-1103/1104]
CB31    Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly     copyir.com [MJ-1103/1104]
CB40    Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally     copyir.com [MJ-1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally     copyir.com [MJ-1103/ 1104]
CB50    Stapler home position error: The stapler home position sensor does not work     copyir.com [MJ-1103/1104]
CB51    Stapler shift home position error: The stapler is not at the home position     copyir.com [MJ-1103/1104]
CB60    Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally     copyir.com [MJ-1103/1104]
CB80    Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON
CB81    Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON     copyir.com [MJ-1103/1104]
CB82    Finisher - Main CPU program error
CB83    Saddle Stitch Finisher - Main CPU program error
CB84    Hole Punch Unit - Main CPU program error
CB91    Saddle Stitch Finisher flash ROM abnormality
CB92    Saddle Stitch Finisher RAM abnormality
CB93    Additional folding motor abnormality
CB94    Saddle transport motor abnormality
CB95    Stacker motor abnormality
CBA0    Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally     copyir.com [MJ-1103/1104]
CBB0    Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally     copyir.com [MJ-1103/1104]
CBC0    Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally     copyir.com [MJ-1103/1104]
CBE0    Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally     copyir.com [MJ-1103/1104]
CC20    Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104]
CC30    Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally     copyir.com [MJ-1103/1104]
CC31    Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally     copyir.com [MJ-1103/1104]
CC41    Paper holder cam home position abnormality: The paper holder cam is not at the home position     copyir.com [MJ1103/1104]
CC51    Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally     copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC52    Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally     copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC60    Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally     copyir.com [MJ1103/1104 (when MJ-6102 is installed)]
CC61    Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally     copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC71    Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on     copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC72    Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on     copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC73    Punching device power supply abnormality
CC74    Punch unit transport pulse abnormality
CC80    Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally     copyir.com [MJ-1103/1104]
CD60    Sub-hopper toner sensors abnormality     copyir.com
CD61    Sub-hopper toner motor-Y abnormality     copyir.com
CD62    Sub-hopper toner motor-M abnormality     copyir.com
CD63    Sub-hopper toner motor-C abnormality     copyir.com
CD64    Sub-hopper toner motor-K abnormality     copyir.com
CD71    Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate     copyir.com
CD80    TRU waste toner motor locking error: The auger (TRU side) in the TRU waste toner transport path does not rotate     copyir.com
CD81    TRU waste toner transport motor locking error: The auger (waste toner box side) in the TRU waste toner transport path does not rotate     copyir.com
CD82    TRU waste toner full-status error
CDE0    Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally     copyir.com [MJ1103/1104]
CE00    Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ-1103/1104 (when MJ-6102 is installed)]
CE10    Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF     copyir.com
CE20    Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed     copyir.com
CE40    Image quality control test pattern abnormality: The test pattern is not formed normally     copyir.com
CE41    Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally     copyir.com
CE42    Image quality TRC control test pattern abnormality (EFI printer board): Image quality TRC control test pattern is not printed normally     copyir.com
CE50    Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range     copyir.com
CE60    Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range     copyir.com
CE71    Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time     copyir.com
CE90    Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range     copyir.com
CEC0    2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally     copyir.com
CF10    Communication module SRAM reading failure     copyir.com
CF90    Laser optical unit shutter abnormality     copyir.com
CFA0    Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal     copyir.com
CFA1    Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal     copyir.com
E010    Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor     copyir.com
E011    Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor     copyir.com
E020    Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor     copyir.com
E030    Power-ON jam: The paper is remaining on the paper transport path when power is turned ON     copyir.com
E061    Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment     copyir.com
E062    Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment     copyir.com
E063    Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment     copyir.com
E064    Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment     copyir.com
E065    Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment     copyir.com
E071    1st drawer media type mis-setting jam: The media type setting of the 1st drawer is incorrect     copyir.com
E072    2nd drawer media type mis-setting jam: The media type setting of the 2nd drawer is incorrect     copyir.com
E073    3rd drawer media type mis-setting jam: The media type setting of the 3rd drawer is incorrect     copyir.com
E074    4th drawer media type mis-setting jam: The media type setting of the 4th drawer is incorrect     copyir.com
E075    Option LCF media type mis-setting jam: The media type setting of the option LCF is incorrect     copyir.com
E076    Tandem LCF media type mis-setting jam: The media type setting of the tandem LCF is incorrect     copyir.com
E090    Image data delay jam: Image data to be printed cannot be prepared     copyir.com
E091    Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware     copyir.com
E0A0    Image transport ready time-out jam: Image data to be printed cannot be sent     copyir.com
E110    ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing     copyir.com
E120    Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor     copyir.com
E130    1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor     copyir.com
E140    2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor     copyir.com
E150    3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
E160    4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor     copyir.com
E180    Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor     copyir.com
E190    LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor     copyir.com
E200    1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor     copyir.com
E210    2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor     copyir.com
E220    2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor     copyir.com
E230    1st drawer misfeeding (Paper not reaching the 1st drawer transport sensor): Paper fed from the 1st drawer does not reach the 1st drawer transport sensor     copyir.com
E240    2nd drawer misfeeding (Paper not reaching the 2nd drawer transport sensor): Paper fed from the 2nd drawer does not reach the 2nd drawer transport sensor     copyir.com
E260    Option LCF transport jam (Paper not reaching the registration sensor)
E270    Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor     copyir.com
E290    Option LCF transport jam: Paper fed from the Option LCF does not reach the 1st drawer transport sensor     copyir.com
E2B0    Stop jam at the registration sensor (1st drawer)
E2B1    Stop jam at the registration sensor (2nd drawer)
E2B2    Stop jam at the registration sensor (3rd drawer)
E2B3    Stop jam at the registration sensor (4th drawer)
E2B4    Stop jam at the registration sensor (Bypass tray)
E2B5    Stop jam at the registration sensor (LCF)
E2B6    Stop jam at the registration sensor (ADU)
E2B7    Stop jam at the registration sensor (option LCF)
E300    3rd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor     copyir.com
E310    3rd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor     copyir.com
E320    3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor     copyir.com
E330    4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor     copyir.com
E340    4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor     copyir.com
E350    4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor     copyir.com
E360    4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor     copyir.com
E370    3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor     copyir.com
E380    4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor     copyir.com
E3C0    LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor     copyir.com
E3D0    LCF transport jam (Paper not reaching the 1st drawer feed sensor): Paper fed from the LCF and passed through the 2nd drawer feed sensor does not reach the 1st drawer feed sensor     copyir.com
E3E0    LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor     copyir.com
E3F0    Tandem LCF misfeeding (Paper not reaching the tandem LCF feed sensor): Paper fed from the Tandem LCF does not reach the tandem LCF transport sensor     copyir.com
E400    Duplexing unit open jam
E430    ADU open jam: The ADU has opened during printing     copyir.com
E440    Paper feed cover open jam: The paper feed cover has opened during printing     copyir.com
E450    LCF side cover open jam: The LCF side cover has opened during printing     copyir.com
E480    Bridge unit open jam: The bridge unit has opened during printing     copyir.com
E4A0    Waste toner cover open jam (printing)
E4B0    Bridge unit open jam (printing): The bridge unit has opened during printing     copyir.com
E510    Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section     copyir.com
E511    ADU misfeeding (Paper not reaching the ADU transport sensor-1)
E540    ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor     copyir.com
E550    Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding)     copyir.com
E570    Jam not reaching the bridge unit     copyir.com
E580    Stop jam at the bridge unit
E590    Jam not reaching the upper paper exit sensor
E5A0    Stop jam at the upper paper exit sensor
E712    Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor     copyir.com
E714    Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray     copyir.com
E721    Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side)     copyir.com
E722    Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section     copyir.com
E724    Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor     copyir.com
E725    Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor     copyir.com
E726    Transport/exit signal reception jam during ADF standby status
E727    Jam not reaching the original reading end sensor
E729    Stop jam at the original reading end sensor
E731    Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor     copyir.com
E744    Stop jam at the exit/reverse sensor
E745    Jam not reaching the exit reverse sensor
E746    Exit/reverse sensor paper remaining jam
E762    Registration sensor paper remaining jam
E770    Original width detection sensor-1 paper remaining jam
E771    Original width detection sensor-2 paper remaining jam
E772    Original width detection sensor-3 paper remaining jam
E773    Intermediate transport sensor paper remaining jam
E774    Reading start sensor paper remaining jam
E775    Reading end sensor paper remaining jam
E777    Exit sensor paper remaining jam
E860    Original jam access cover open: The Original jam access cover has opened during RADF operation     copyir.com
E870    RADF open jam: RADF has opened during RADF operation     copyir.com
E871    Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment     copyir.com
E910    Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor     copyir.com
E920    Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor     copyir.com
E930    Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1     copyir.com
E940    Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2     copyir.com
E970    Jam not reaching the lower paper exit sensor: Paper transported from the bridge unit does not reach the lower paper exit sensor     copyir.com
E980    Stop jam at the lower paper exit sensor: Paper transported from the bridge unit does not pass the lower paper exit sensor     copyir.com
E9F0    Punching jam: Punching is not performed properly     copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
EA10    Paper transport delay jam: The paper which has passed the relay transport path does not reach the inlet sensor     copyir.com [MJ-1103/1104]
EA20    Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor     copyir.com [MJ1103/1104]
EA21    Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec     copyir.com [MJ-1103/1104]
EA22    Paper transport jam (Finisher paper punching edge detection sensor): [MJ-1103/1104]
EA23    Paper transport jam (exit sensor): [MJ-1103/1104]
EA24    Paper transport jam (between entrance and exit sensors): [MJ-1103/1104]
EA25    Paper transport jam (after paper stack exit): [MJ1103/1104]
EA26    Paper transport jam (stop command request): [MJ1103/1104]
EA27    Paper transport jam (paper not inserted): [MJ-1103/ 1104]
EA28    Paper transport jam (assisting arm operation delay): [MJ-1103/1104]
EA29    Paper transport jam (stack transport delay): [MJ1103/1104]
EA31    Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor     copyir.com [MJ-1103/1104]
EA32    Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON     copyir.com [MJ-1103/1104]
EA40    Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing     copyir.com [MJ-1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport     copyir.com [MJ-1103/1104]
EA50    Stapling jam: Stapling is not performed properly     copyir.com [MJ-1103/1104]
EA60    Early arrival jam: The inlet sensor detects the paper earlier than a specified timing     copyir.com [MJ-1103/1104]
EA70    Stack exit belt home position error: The stack exit belt is not at the home position     copyir.com [MJ-1103/1104]
EA90    Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104]     copyir.com
EAA0    Power-ON jam: Paper exists at No     copyir.com1 paper sensor, No     copyir.com 2 paper sensor, No     copyir.com3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON     copyir.com [MJ-1103/1104]
EAB0    Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No     copyir.com1 paper sensor, No     copyir.com 2 paper sensor, No     copyir.com3 paper sensor or delivery sensor     copyir.com [MJ-1103/1104]
EAB1    Short paper jam (Saddle Stitch Finisher)
EAD0    Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing     copyir.com
EAE0    Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher     copyir.com
EB30    Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing     copyir.com
EB50    Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper     copyir.com
EB60    Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50])     copyir.com
ED10    Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position     copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
ED11    Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position     copyir.com [MJ-1103/1104 (when MJ6102 is installed)]
ED12    Shutter home position error: The shutter is not at the home position     copyir.com [MJ-1103/1104]
ED13    Front alignment plate home position error: The front alignment plate is not at the home position     copyir.com [MJ1103/1104]
ED14    Rear alignment plate home position error: The rear alignment plate is not at the home position     copyir.com [MJ1103/1104]
ED15    Paddle home position error: The paddle is not at the home position     copyir.com [MJ-1103/1104]
ED16    Buffer tray home position error: The buffer tray is not at the home position     copyir.com [MJ-1103/1104]
EF10    Paper not supported for Saddle Stitch Finisher
EF11    Saddle Stitch Finisher stapling error (front)
EF12    Saddle Stitch Finisher stapling error (rear)
EF13    Saddle paper holder home position detection abnormality
EF14    Saddle paper exit jam
EF15    Saddle Stitch Finisher side alignment motor home position detection abnormality
EF16    Saddle Stitch Finisher stacker motor home position detection abnormality
EF17    Saddle Stitch Finisher folding blade home position detection abnormality
EF18    Saddle Stitch Finisher additional folding roller home position detection abnormality
EF19    Saddle paper folding jam
EF20    Saddle stacker jam
EF21    Hole Punch Unit paper leading edge skew detection abnormality
EF22    Hole Punch Unit paper leading edge detection abnormality
EF23    Hole Punch Unit paper alignment abnormality
EF24    Hole Punch Unit paper trailing edge skew detection abnormality
EF25    Hole Punch Unit paper trailing edge detection abnormality
EF27    Hole Punch Unit paper edge detection order abnormality-1
EF28    Hole Punch Unit paper edge detection order abnormality-2
F070    Communication error between System-CPU and Engine-CPU
F090    SRAM abnormality on the SYS board
F100    HDD format error: HDD cannot be initialized normally     copyir.com
F101    HDD unmounted: Connection of HDD cannot be detected     copyir.com
F102    HDD start error: HDD cannot become ‘Ready’ state
F103    HDD transfer time-out: Reading/writing cannot be performed in the specified period of time     copyir.com
F104    HDD data error: Abnormality is detected in the data of HDD     copyir.com
F105    HDD other error
F106    Point and Print partition damage
F107    /BOX partition damage
F108    /SHA partition damage
F110    Communication error between System-CPU and Scanner-CPU
F111    Scanner response abnormality
F120    Database abnormality: Database is not operating normally     copyir.com
F130    Invalid MAC address
F200    Data Overwrite option (GP-1070) disabled
F350    SLG board abnormality
F400    SYS board cooling fan abnormality

خواندن 1381 دفعه

نظرات (0)

نظر ارسال شده‌ی جدیدی وجود ندارد

دیدگاه خود را بیان کنید

  1. ارسال دیدگاه بعنوان یک مهمان -
پیوست ها (0 / 3)
اشتراک‌گذاری موقعیت مکانی شما

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب