Your browser does not support JavaScript! > کیو سرا میتا taskalfa 300ci

   کانال تلگرام کپی ایران

(0) محصول
سه شنبه, 14 ارديبهشت 1395 17:21

کیو سرا میتا taskalfa 300ci

نوشته شده توسط
این مورد را ارزیابی کنید
(0 رای‌ها)

C0030    Fax control PWB system problem
Processing with the fax software was disabled due to a hardware or software problem        copyir.com    Defective fax control PWB        copyir.com
C0070    Abnormal detection of fax control PWB incompatibility
In the initial communication with the fax control PWB, any normal communication command is not transmitted        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0100    Backup memory (EEPROM) device problem (Main PWB)
Reading from or writing to EEPROM cannot be performed        copyir.com    Defective main PWB        copyir.com
Device damage of EEPROM        copyir.com
C0110    Backup memory (EEPROM) data problem (Main PWB)
Reading data from EEPROM is abnormal        copyir.com    Data damage of EEPROM        copyir.com
C0150    Backup memory (EEPROM) device problem (Engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Defective engine PWB        copyir.com
Device damage of EEPROM        copyir.com
C0160    Backup memory (EEPROM) data problem (Engine PWB)
Reading data from EEPROM is abnormal        copyir.com    Data damage of EEPROM        copyir.com
C0170    Copy counts problem
A checksum error is detected in the main and sub backup memories for the copy counters        copyir.com    Data damage of EEPROM        copyir.com
Defective main PWB        copyir.com
C0180    Machine number mismatch error
Machine number of main PWB and engine PWB does not match        copyir.com    Data damage of EEPROM        copyir.com
C0320    Power CPU communication problem
A communication error is detected 10 times in succession        copyir.com    Defective engine PWB        copyir.com
C0620    FAX image DIMM problem DIMM is not installed correctly        copyir.com
DIMM cannot be accessed        copyir.com    DIMM installed incorrectly        copyir.com
Defective main PWB        copyir.com
C0630    DMA problem
DMA transmission of image data does not complete within the specified period of time        copyir.com    Poor contact in the connector terminals        copyir.com
Defective main PWB        copyir.com
C0640    Hard disk drive problem
The hard disk cannot be accessed        copyir.com    Poor contact in the connector terminals        copyir.com
Defective hard disk        copyir.com
Defective main PWB        copyir.com
C0650    FAX image DIMM check problem
Incorrect DIMM is installed        copyir.com If DIMM from another Fax System is installed        copyir.com    DIMM installed incorrectly        copyir.com Original DIMM not installed        copyir.com
Defective main PWB        copyir.com
C0800    Image processing problem
JAM05 is detected twice        copyir.com    Defective main PWB        copyir.com
C0820    Fax control PWB CG ROM checksum error (optional fax)
A checksum error occurred with the CG ROM data of the fax control PWB        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0830    Fax control PWB flash program area checksum error (optional fax)
A checksum error occurred with the program of the fax control PWB        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed        copyir.com    Defective main PWB        copyir.com
The battery is disconnected from the main PWB        copyir.com
C0860    Fax control PWB software switch checksum error (optional fax)
A checksum error occurred with the software switch value of the fax control PWB        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0870    Fax control PWB to main PWB high capacity data transfer problem
High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C0880    Program archive problem (optional fax)
When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0890    Fax control PWB CG FONT archive problem (optional fax)
When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0920    Fax file system error
The backup data is not retained for file system abnormality of flash memory of the fax control PWB        copyir.com    Defective fax control PWB        copyir.com
C1010    Lift motor 1 error
After cassette 1 is inserted, lift limit switch 1 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of lift motor 1        copyir.com
Defective lift motor 1        copyir.com
Defective lift switch 1        copyir.com
Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C1020    Lift motor 2 error
After cassette 2 is inserted, lift limit switch 2 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of lift motor 2        copyir.com
Defective lift motor 2        copyir.com
Defective lift switch 2        copyir.com
Poor contact in the connector terminals        copyir.com
Defective PWB
C1030    PF lift motor 1 error (optional paper feeder)
After cassette 3 is inserted, PF lift switch 1 does not turn on within 12 s        copyir.com This error is detected two times successively        copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more two times successively        copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of PF lift motor 1        copyir.com
Defective PF lift motor 1        copyir.com
Defective PF lift switch 1        copyir.com
C1040    PF lift motor 2 error (optional paper feeder)
After cassette 4 is inserted, PF lift switch 2 does not turn on within 12 s        copyir.com This error is detected two times successively        copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more two times successively        copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of PF lift motor 2        copyir.com
Defective PF lift motor 2        copyir.com
Defective PF lift switch 2        copyir.com
C1100    PF lift motor 1 error (optional 3000sheet paper feeder)
A motor over-current signal is detected continuously for 1 s or longer        copyir.com    Poor contact in the connector terminals        copyir.com
PF lift motor 1 does not rotate correctly (the motor is overloaded)        copyir.com
C1110    PF lift motor 2 error (optional 3000sheet paper feeder)
A motor over-current signal is detected continuously for 1 s or longer        copyir.com    Poor contact in the connector terminals        copyir.com
PF lift motor 2 does not rotate correctly (the motor is overloaded)        copyir.com
C1120    PF left lift position problem (optional 3000-sheet paper feeder)
Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective level switch 1        copyir.com
Defective PF lift motor 2        copyir.com
The PF left lift does not rise properly        copyir.com
C1130    PF right lift position problem (optional 3000-sheet paper feeder)
Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective level switch 2        copyir.com
Defective PF lift motor 1        copyir.com
The PF right lift does not rise properly        copyir.com
C1400    Rotary guide motor error
Rotary guide sensor does not turn on        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gear s or couplings of rotary guide motor        copyir.com
Defective rotary guide motor        copyir.com
Defective rotary guide sensor        copyir.com
Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C1800    Paper feeder communication error (optional paper feeder)
A communication error from paper feeder is detected 10 times in succession        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C1900    Paper feeder EEPROM error (optional paper feeder)
When writing the data, the write data and the read data is not continuously in agreement three times        copyir.com    Poor contact in the connector terminals        copyir.com
Defective engine PWB        copyir.com
Defective paper feeder        copyir.com
C1950    Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective transfer belt speed PWB (inner transfer belt unit)        copyir.com
C2101    Developing motor K error
The rated speed achievement signal does not turn to L within 2 s since developing motor K is activated        copyir.com The rated speed achievement signal is at the H level for 1 s continuously after developing motor K is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective developing motor K        copyir.com
Defective engine PWB        copyir.com
C2102    Developing motor MCY error
The rated speed achievement signal does not turn to L within 2 s since developing motor MCY is activated        copyir.com The rated speed achievement signal is at the H level for 1 s continuously after developing motor MCY is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective developing motor MCY        copyir.com
Defective engine PWB        copyir.com
C2201    Drum motor K steady-state error
Drum motor K does not keep the steady-state speed for 5 s successively since the motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor K        copyir.com
Defective PWB        copyir.com
C2202    Drum motor C steady-state error
Drum motor C does not keep the steady-state speed for 5 s successively since the motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor C        copyir.com
Defective PWB        copyir.com
C2203    Drum motor M steady-state error
Drum motor M does not keep the steady-state speed for 5 s successively since the motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor M        copyir.com
Defective PWB        copyir.com
C2204    Drum motor Y steady-state error
Drum motor Y does not keep the steady-state speed for 5 s successively since the motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor Y        copyir.com
Defective PWB        copyir.com
C2211    Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor K        copyir.com
Defective PWB        copyir.com
C2212    Drum motor C startup error
Drum motor C is not stabilized within 5 s since the motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor C        copyir.com
Defective PWB
C2213    Drum motor M startup error
Drum motor M is not stabilized within 5 s since the motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor M        copyir.com
Defective PWB
C2214    Drum motor Y startup error
Drum motor Y is not stabilized within 5 s since the motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor Y        copyir.com
Defective PWB
C2231    Drum motor K main sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor K        copyir.com
Defective PWB        copyir.com
C2232    Drum motor C main sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals
Defective drum motor C        copyir.com
Defective PWB        copyir.com
C2233    Drum motor M main sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor M        copyir.com
Defective PWB        copyir.com
C2234    Drum motor Y main sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor Y        copyir.com
Defective PWB        copyir.com
C2241    Drum motor K sub sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor K        copyir.com
Defective PWB        copyir.com
C2242    Drum motor C sub sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor C
Defective PWB        copyir.com
C2243    Drum motor M sub sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor M        copyir.com
Defective PWB        copyir.com
C2244    Drum motor Y sub sensor error
No signal is input to the sensor for 1        copyir.com5 s continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor Y        copyir.com
Defective PWB        copyir.com
C2261    Drum motor K device sensor error
The device alarm signal is input        copyir.com    Poor contact in the connector terminals
Defective drum motor K        copyir.com
Defective PWB        copyir.com
C2262    Drum motor C device error
The device alarm signal is input        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor C        copyir.com
Defective PWB
C2263    Drum motor M device error
The device alarm signal is input        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor M        copyir.com
Defective PWB        copyir.com
C2264    Drum motor Y device error
The device alarm signal is input        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum motor Y        copyir.com
Defective PWB        copyir.com
C2271    Drum position sensor K error
While the drum rotates two turns, no signal is input to the sensor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum position sensor K        copyir.com
Defective PWB        copyir.com
C2272    Drum position sensor C error
While the drum rotates two turns, no signal is input to the sensor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum position sensor C        copyir.com
Defective PWB        copyir.com
C2273    Drum position sensor M error
While the drum rotates two turns, no signal is input to the sensor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum position sensor M        copyir.com
Defective PWB        copyir.com
C2274    Drum position sensor Y error
While the drum rotates two turns, no signal is input to the sensor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum position sensor Y        copyir.com
Defective PWB        copyir.com
C2300    Fuser motor error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective fuser motor        copyir.com
Defective engine PWB        copyir.com
C2351    Cleaning motor K error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective cleaning motor K        copyir.com
Defective engine PWB        copyir.com
C2352    Cleaning motor MCY error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective cleaning motor K        copyir.com
Defective engine PWB        copyir.com
C2400    Eject motor error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective eject motor        copyir.com
Defective engine PWB        copyir.com
C2500    MP motor error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective MP motor        copyir.com
Defective engine PWB        copyir.com
C2550    Paper conveying motor error
After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective paper conveying motor        copyir.com
Defective PWB        copyir.com
C2600    PF paper conveying motor error (optional paper feeder)
The lock signal of the motor is detected above 450 ms        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective paper PF conveying motor        copyir.com
Defective PWB        copyir.com
C2700    Color release motor error
After driving of the color release motor starts, the error signal is not at the H level for 4 s continuously        copyir.com After driving of the color release motor starts, the release signal does not turn to the L level within 5 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective color release motor
Defective engine PWB        copyir.com
C2810    Waste toner motor error
After driving of the waste toner motor starts, the error signal is not at the H level for 2 s continuously        copyir.com    Poor contact in the connector terminals
Defective drive transmission system        copyir.com
Defective waste toner motor        copyir.com
Defective engine PWB
C2950    Motor control PWB communication error
A communication error from motor control PWB is detected 10 times in succession        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C3100    Scanner carriage problem
The home position is not correct when the power is turned on or at the start of copying using the table        copyir.com    Poor contact in the connector terminals        copyir.com
Defective home position switch        copyir.com
Defective scanner motor        copyir.com
The mirror frame, exposure lamp, or scanner wire is defective        copyir.com
Defective PWB        copyir.com
C3200    Exposure lamp problem
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective exposure lamp or inverter PWB        copyir.com
Incorrect shading position        copyir.com
Defective PWB
C3210    CIS lamp problem
When input value at the time of CIS illumination does not exceed the threshold value between 5 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective DP driver PWB
Defective DP inverter PWB        copyir.com
Defective CIS        copyir.com
C3300    Optical system (AGC) problem
After AGC, correct input is not obtained at CCD        copyir.com    Poor contact in the connector terminals        copyir.com
Defective exposure lamp or inverter PWB        copyir.com
Defective PWB        copyir.com
C3310    CIS AGC problem
After AGC, correct input is not obtained at CIS        copyir.com    Defective DP driver PWB        copyir.com
CIS output problem        copyir.com
Defective DP inverter PWB        copyir.com
C3500    Communication error between scanner and ASIC
An error code is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C3900    Backup memory read/write problem (ISC PWB)
Read and write data does not match        copyir.com    Defective backup RAM or PWB        copyir.com
C3910    Backup memory data problem (ISC PWB)
Data in the specified area of the backup memory does not match the specified values        copyir.com    Defective backup RAM or PWB        copyir.com
C4000    Polygon motor synchronization problem
The rated speed achievement signal won’t turn to L in 48 s since the polygon motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective polygon motor        copyir.com
Defective engine PWB        copyir.com
C4010    Polygon motor steady-state problem
The rated speed achievement signal turns to H every other 24 s after the polygon motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective polygon motor        copyir.com
Defective engine PWB        copyir.com
C4100    BD initialization problem
When power is turned on, ASIC of engine PWB detects a BD error for 1 s after the polygon motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective APC PWB BK (inner laser scanner unit)
Defective engine PWB        copyir.com
C5101    Main high-voltage K error
Abnormality of charger roller K is detected when Vpp adjustment        copyir.com    Installation defectiveness on charger roller unit K        copyir.com
Defective charger roller unit K
C5102    Main high-voltage C error
Abnormality of charger roller C is detected when Vpp adjustment        copyir.com    Installation defectiveness on charger roller unit C        copyir.com
Defective charger roller unit C
C5103    Main high-voltage M error
Abnormality of charger roller M is detected when Vpp adjustment        copyir.com    Installation defectiveness on charger roller unit M        copyir.com
Defective charger roller unit M        copyir.com
C5104    Main high-voltage Y error
Abnormality of charger roller Y is detected when Vpp adjustment        copyir.com    Installation defectiveness on charger roller unit Y        copyir.com
Defective charger roller unit Y        copyir.com
C6000    Fuser heater 1 break Fuser thermistor 1 detects a temperature lower than the Ready indication temperature for 90 s during warming up        copyir.com Fuser thermistor 1 deduced less than 130 C/266F for 5 s during stand-by        copyir.com Fuser thermistor 1 does not reach 75C/ 167F even after 30 s during warming up        copyir.com    Defective fuser heater 1        copyir.com
Defective fuser thermostat 1        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6010    Abnormally high fuser thermistor temperature
The fuser Abnormally high signal is detected for 60 s or more        copyir.com    Defective PWB        copyir.com
C6020    Abnormally high fuser thermistor 1 temperature The fuser temperature exceeds 240 C/464 F for 1 s        copyir.com    Installation defectiveness on fuser thermistor 1
Defective PWB
C6030    Fuser thermistor 1 break error During warming up, fuser thermistor 1 does not detect temperature rise of 1 C/1        copyir.com8F for 10 s        copyir.com When the difference of temperature of fuser thermistor 1 and 2 becomes 100C/212F or more        copyir.com    Defective fuser heater 1        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6040    Fuser heater error
Fuser thermistor 1 detects temperature change of 20C/36F or more for 160 ms 100 times or more since the power is turned on        copyir.com    Defective fuser heater 1        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB
C6050    Abnormally low fuser thermistor 1 temperature
During printing, the temperature at the heat roller lower than 100C/212F is detected continuously for 1 s        copyir.com    Defective fuser heater 1        copyir.com
Defective PWB
C6100    Fuser heater 2 break
Fuser thermistor 2 detected less than 100C/212F for 120 s during driving        copyir.com Fuser thermistor 2 deduced less than 150C/302F for 300 s during driving        copyir.com Fuser thermistor 2 deduced less than 100C/212F for 5 s during driving        copyir.com    Defective fuser heater 2        copyir.com
Defective fuser thermostat 2        copyir.com
Installation defectiveness on fuser thermistor 2        copyir.com
Defective PWB        copyir.com
C6120    Abnormally high fuser thermistor 2 temperature
The fuser temperature exceeds 190C/ 374F for 1 s        copyir.com    Installation defectiveness on fuser thermistor 2        copyir.com
Defective PWB
C6130    Fuser thermistor 2 break error Fuser thermistor 2 detects a temperature of 30 C/86F or lower for 45 s        copyir.com    Installation defectiveness on fuser thermistor 2        copyir.com
Defective fuser heater 2        copyir.com
Defective PWB        copyir.com
C6200    Fuser heater 1 edge break
During warming up, fuser thermistor 1 does not detect temperature rise of 1C/ 1        copyir.com8F for 10 s        copyir.com Fuser thermistor 1 does not reach 90F even after 30 s during warming up        copyir.com    Defective fuser heater 1        copyir.com
Defective fuser thermostat 1        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6220    Abnormally high fuser thermistor 1 edge temperature
The fuser temperature exceeds 250C/ 482F for 1 s        copyir.com    Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6230    Fuser thermistor 1 edge break error Fuser thermistor 1 detects a temperature of 40C/104F or lower for 30 s        copyir.com    Defective fuser heater 1        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6400    Zero-cross signal error
While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C6410    Fuser unit type mismatch problem
Absence of the fuser unit is detected        copyir.com    Fuser unit connector inserted incorrectly        copyir.com
Different type of the fuser unit is installed        copyir.com
C7000    Toner motor problem
After driving of the toner motor starts, the error signal is not at the H level for 500 ms continuously        copyir.com    Poor contact in the connector terminals        copyir.com
Broken the gear
Defective toner motor M/C/Y/K        copyir.com
Defective engine PWB        copyir.com
C7100    Toner container motor error
The rated speed achievement signal does not turn to L within 2 s since toner container motor is activated        copyir.com The rated speed achievement signal is at the H level for 1 s continuously after toner container motor is stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective toner container motor
Defective engine PWB        copyir.com
C7101    Toner sensor K problem
Sensor output value of 60 or less or 944 or more continued for 3 s        copyir.com    Defective developing unit K        copyir.com
Defective PWB        copyir.com
C7102    Toner sensor C problem Sensor output value of 60 or less or 944 or more continued for 3 s        copyir.com    Defective developing unit C        copyir.com
Defective PWB        copyir.com
C7103    Toner sensor M problem Sensor output value of 60 or less or 944 or more continued for 3 s        copyir.com    Defective developing unit M        copyir.com
Defective PWB        copyir.com
C7104    Toner sensor Y problem
Sensor output value of 60 or less or 944 or more continued for 3 s        copyir.com    Defective developing unit Y        copyir.com
Defective PWB
C7200    Broken internal thermistor wire
An abnormal value is detected in the input data to inner temperature sensor 1        copyir.com    Poor contact in the connector terminals
Defective laser scanner unit        copyir.com
Defective engine PWB        copyir.com
C7210    Short-circuited internal thermistor
An abnormal value is detected in the input data to inner temperature sensor 1        copyir.com    Poor contact in the connector terminals        copyir.com
Defective laser scanner unit        copyir.com
Defective engine PWB        copyir.com
C7240    Broken internal thermistor 2 wire
An abnormal value is detected in the input data to inner temperature sensor 2        copyir.com    Poor contact in the connector terminals        copyir.com
Defective engine PWB
C7250    Short-circuited internal thermistor 2
An abnormal value is detected in the input data to inner temperature sensor 2        copyir.com    Poor contact in the connector terminals        copyir.com
Defective engine PWB        copyir.com
C7401    Developing unit K type mismatch problem
Absence of the developing unit K is detected        copyir.com    Developing unit connector inserted incorrectly        copyir.com
Different type of the developing unit is installed        copyir.com
C7402    Developing unit C type mismatch problem
Absence of the developing unit C is detected        copyir.com    Developing unit connector inserted incorrectly        copyir.com
Different type of the developing unit is installed        copyir.com
C7403    Developing unit M type mismatch problem
Absence of the developing unit M is detected        copyir.com    Developing unit connector inserted incorrectly        copyir.com
Different type of the developing unit is installed        copyir.com
C7404    Developing unit Y type mismatch problem
Absence of the developing unit Y is detected        copyir.com    Developing unit connector inserted incorrectly        copyir.com
Different type of the developing unit is installed
C7411    Drum unit K type mismatch problem
Absence of the drum unit K is detected        copyir.com    Drum unit connector inserted incorrectly        copyir.com
Different type of the drum unit is installed        copyir.com
C7412    Drum unit C type mismatch problem
Absence of the drum unit C is detected        copyir.com    Drum unit connector inserted incorrectly        copyir.com
Different type of the drum unit is installed        copyir.com
C7413    Drum unit M type mismatch problem
Absence of the drum unit M is detected        copyir.com    Drum unit connector inserted incorrectly        copyir.com
Different type of the drum unit is installed        copyir.com
C7414    Drum unit Y type mismatch problem
Absence of the drum unit Y is detected        copyir.com    Drum unit connector inserted incorrectly        copyir.com
Different type of the drum unit is installed        copyir.com
C7420    Transfer belt unit type mismatch problem
Absence of the transfer belt unit is detected        copyir.com    Transfer belt unit connector inserted incorrectly        copyir.com
Different type of the transfer belt unit is installed        copyir.com
C7800    Broken external thermistor wire
An abnormal value is detected in the input data to the outer temperature sensor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C7901    Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum PWB K        copyir.com
C7902    Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum PWB C        copyir.com
C7903    Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum PWB M        copyir.com
C7904    Drum Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Defective drum PWB Y        copyir.com
C7911    Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective developing PWB K        copyir.com
C7912    Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective developing PWB C        copyir.com
C7913    Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective developing PWB M        copyir.com
C7914    Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively        copyir.com Mismatch of reading data from two locations occurs eight times successively        copyir.com Mismatch between writing data and reading data occurs eight times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Defective developing PWB Y        copyir.com
C7950    High voltage control PWB error
A communication error from high voltage control PWB is detected 10 times in succession    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C8020    Punch motor problem (optional 3000sheet document finisher) The error signal of the punch motor is detected for more than 500 ms while the punch motor is operating        copyir.com    Poor contact in the connector terminals        copyir.com
Defective punch motor        copyir.com
Defective PWB        copyir.com
C8030    Tray upper limit detection problem (optional document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected        copyir.com    The tray upper limit sensor, paper surface sensor 1/2 connector makes poor contact        copyir.com
Defective tray upper limit sensor, paper surface sensor 1/2        copyir.com
Defective finisher main PWB        copyir.com
C8040    Belt problem (optional document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on        copyir.com    The belt sensor, belt solenoid connector makes poor contact        copyir.com
Defective belt sensor        copyir.com
Defective belt solenoid        copyir.com
Defective finisher main PWB        copyir.com
C8050    Paper conveying belt motor 1 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 1 does not turn off within 1        copyir.com5 s        copyir.com Paper conveying belt home position sensor 1 does not turn on within 2        copyir.com5 s        copyir.com Jam 88 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective paper conveying belt home position sensor 1        copyir.com
Defective paper conveying belt motor 1        copyir.com
Defective PWB        copyir.com
C8060    Paper conveying belt motor 2 problem (optional 3000-sheet document finisher)
Paper conveying belt home position sensor 2 does not turn off within 1        copyir.com5 s        copyir.com Paper conveying belt home position sensor 2 does not turn on within 1        copyir.com5 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective paper conveying belt home position sensor 2        copyir.com
Defective paper conveying belt motor 2        copyir.com
Defective PWB
C8070    Inner tray communication error (optional 3000-sheet document finisher)
Communication with the inner tray is not possible although the connection is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C8140    Main tray problem (optional 3000sheet document finisher)
The main tray is not detected by the main tray upper limit detection sensor or the main tray paper upper surface detection sensor within 20 s since the tray has started ascending        copyir.com The main tray upper limit detection sensor or the main tray paper upper surface detection sensor is not detected to be turned off in 20 s after the main tray has descended        copyir.com The main tray low limit detection sensor is not detected to be turned on in 20 s after the main tray has descended        copyir.com During main tray ascent, the main tray upper limit detection sensor or the main tray paper upper surface detection sensor stays on for more than 2 s        copyir.com Tray elevation motor problem (optional document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective main tray motor        copyir.com
Defective main tray upper limit detection sensor/main tray paper upper surface detection sensor/main tray lower limit detection sensor        copyir.com
Defective finisher main PWB        copyir.com
The tray elevation motor connector makes poor contact        copyir.com
The tray elevation motor malfunctions        copyir.com
The tray lower limit sensor, paper surface sensor 1/2 connector makes poor contact        copyir.com
Defective tray lower limit sensor, paper surface sensor 1/2        copyir.com
Defective finisher main PWB        copyir.com
C8170    Side registration motor 1 problem (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed        copyir.com Jam 88 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective side registration motor 1        copyir.com
Defective PWB        copyir.com
C8180    Side registration motor 2 problem (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed        copyir.com Jam 88 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective side registration motor 2        copyir.com
Defective PWB
C8210    Stapler moving motor 1 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 1        copyir.com5 s passed        copyir.com Stapler problem (optional document finisher) Jam 82 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective stapler moving motor 1        copyir.com
Defective finisher main PWB        copyir.com
The stapler connector makes poor contact        copyir.com
The stapler is blocked with a staple        copyir.com
The stapler is broken        copyir.com
Defective finisher main PWB        copyir.com
C8220    Stapler moving motor 2 error (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3        copyir.com5 s passed        copyir.com    Poor contact in the connector terminals        copyir.com
Defective stapler moving motor 2        copyir.com
Defective staple relay PWB        copyir.com
Defective finisher main PWB        copyir.com
C8230    Stapler motor problem (optional 3000sheet document finisher)
Jam 82 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective stapler motor        copyir.com
Defective staple relay PWB        copyir.com
Defective finisher main PWB        copyir.com
C8300    Center-folding unit communication error (optional center-folding unit of 3000-sheet document finisher)
Communication with the center-folding unit is not possible although the connection is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold set switch        copyir.com
Defective centerfold main PWB        copyir.com
Defective finisher main PWB        copyir.com
C8310    Centerfold side registration motor 2 problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1 s passed        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold side registration motor 2        copyir.com
Defective PWB
C8320    Centerfold paper conveying belt motor problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 2        copyir.com5 s passed        copyir.com
Adjustment motor 2 problem (optional document finisher) The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold paper conveying belt motor 1/2        copyir.com
Defective PWB
The adjustment sensor 2, adjustment motor 2 connector makes poor contact        copyir.com
Defective adjustment sensor 2        copyir.com
Defective adjustment motor 2        copyir.com
Defective finisher main PWB        copyir.com
C8330    Blade motor problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1        copyir.com5 s passed
Adjustment motor 1 problem (optional document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective blade motor        copyir.com
Defective PWB
The adjustment sensor 1, adjustment motor 1 connector makes poor contact        copyir.com
Defective adjustment sensor 1        copyir.com
Defective adjustment motor 1        copyir.com
Defective finisher main PWB        copyir.com
C8340    Centerfold staple motor problem (optional center-folding unit of 3000sheet document finisher)
Jam 89 is indicated        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold staple motor        copyir.com
Defective PWB        copyir.com
C8350    Centerfold side registration motor 1 problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1 s passed        copyir.com
Roller motor problem (optional document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold side registration motor 1        copyir.com
Defective PWB        copyir.com
The roller sensor, roller motor connector makes poor contact        copyir.com
Defective roller sensor        copyir.com
Defective roller motor        copyir.com
Defective finisher main PWB        copyir.com
C8360    Centerfold main motor problem (optional center-folding unit of 3000sheet document finisher)
The motor lock signal is detected above 1 s during driving the centerfold main motor        copyir.com
Slide motor problem (optional document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective centerfold main motor        copyir.com
Defective PWB        copyir.com
The slide sensor, slide motor connector makes poor contact        copyir.com
Defective slide sensor
Defective slide motor        copyir.com
Defective finisher main PWB        copyir.com
C8440    Sensor adjusting problem (optional document finisher)
The sensor cannot be adjusted within the specified range        copyir.com    The paper entry sensor connector makes poor contact        copyir.com
Defective paper entry sensor        copyir.com
The optical path of the paper entry sensor is blocked by foreign matter        copyir.com
Defective finisher main PWB        copyir.com
C8460    EEPROM problem (optional document finisher)
Reading from or writing to EEPROM cannot be performed        copyir.com    Defective EEPROM or finisher main PWB        copyir.com
C8500    Mailbox communication error (optional mailbox of 3000-sheet document finisher)
Communication with the mailbox is not possible although the connection is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C8510    Mailbox drive motor problem (optional mailbox of 3000-sheet document finisher) The motor lock signal is detected above 500 ms during driving the mailbox drive motor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective mailbox drive motor
Defective PWB        copyir.com
C8800    Document finisher communication error (optional 3000-sheet document finisher)
A communication error from document finisher is detected 10 times in succession        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C8900    Backup memory data problem (optional 3000-sheet document finisher)
Read and write data does not match 3 times in succession        copyir.com    Poor contact in the connector terminals        copyir.com
EEPROM installed incorrectly        copyir.com
Defective finisher main PWB        copyir.com
C8910    Backup memory data problem (optional of 3000-sheet document finisher)
Read and write data does not match 3 times in succession        copyir.com    Poor contact in the connector terminals
Defective punch PWB        copyir.com
C8930    Backup memory data problem (optional center-folding unit of 3000sheet document finisher)
Read and write data does not match 3 times in succession        copyir.com    Poor contact in the connector terminals
EEPROM installed incorrectly        copyir.com
Defective centerfold main PWB        copyir.com
C9000    DP communication problem (optional DP)
A communication error is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C9040    DP lift motor going up error (optional DP)
The tray upper limit switch does not turn on within 2 s of DP lift motor turning on        copyir.com    Loose connection of the DP lift motor connector        copyir.com
Malfunction of the DP lift motor        copyir.com
Loose connection of the tray upper limit switch connector        copyir.com
Malfunction of the tray upper limit switch        copyir.com
Defective DP driver PWB        copyir.com
C9050    DP lift motor going down error (optional DP)
The tray lower limit switch does not turn on within 2 s of DP lift motor turning on        copyir.com    Loose connection of the DP lift motor connector        copyir.com
Malfunction of the DP lift motor        copyir.com
Loose connection of the tray lower limit switch connector        copyir.com
Malfunction of the tray lower limit switch        copyir.com
Defective DP driver PWB        copyir.com
C9060    DP EEPROM error (optional DP)
Read and write data does not match        copyir.com Data in the specified area of the backup memory does not match the specified values        copyir.com    Defective DP main PWB        copyir.com
Device damage of EEPROM        copyir.com
C9070    Communication problem between DP and SHD (optional DP)
A communication error is detected        copyir.com    Loose connection of the SHD PWB        copyir.com
Defective SHD PWB        copyir.com
C9080    Communication problem between DP and CIS (optional DP)
A communication error is detected        copyir.com    Loose connection of CIS        copyir.com
Defective CIS        copyir.com
C9500-C9550    Contact the Service Administrative Division        copyir.com    
F000    Operation panel PWB communication error    Firmware upgrade error
Defective main PWB        copyir.com
Defective main operation panel PWB        copyir.com
F040    Engine PWB communication error    Firmware upgrade error
Defective main PWB        copyir.com
Defective engine PWB        copyir.com
F041    Scanner PWB communication error    Defective main PWB        copyir.com
Defective ISM PWB        copyir.com

خواندن 1095 دفعه

نظر دادن

از پر شدن تمامی موارد الزامی ستاره‌دار (*) اطمینان حاصل کنید. کد HTML مجاز نیست.

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب