Your browser does not support JavaScript! > سرویس مانوئل کیوسرا میتا

   کانال تلگرام کپی ایران

(0) محصول
سرویس مانوئل کیوسرا میتا
یکشنبه, 19 ارديبهشت 1395 14:28

کیو سرا میتا Kyocera-Mita TASKalfa 620

C0060    Main PWB type mismatch error    Poor contact in the connector terminals     copyir.com
C0100    Backup memory read/write problem
• Read and write data does not match     copyir.com    Defective main PWB     copyir.com
C0110    Backup memory data problem (main PWB)
• Data in the specified area of the backup memory does not match the specified values     copyir.com    Problem with the backup memory data     copyir.com
Defective main PWB     copyir.com
C0130    Backup memory (EEPROM) device problem
• Reading from or writing to EEPROM cannot be performed     copyir.com    Defective main PWB     copyir.com
Device damage of EEPROM     copyir.com
C0140    Backup memory (EEPROM) data problem
• Reading data from EEPROM is abnormal     copyir.com    Data damage of EEPROM     copyir.com
C0150    Backup memory device problem (Engine PWB)
• An error occurs in backup data read or write for the engine PWB     copyir.com    Data damage of EEPROM     copyir.com
C0160    Backup memory data problem (Engine PWB)
• Data for backup data check is changed at the check after startup     copyir.com    Problem with the backup memory data     copyir.com
Defective engine PWB     copyir.com
C0170    Copy counts problem
• A checksum error is detected in the main and engine backup memories for the copy counters     copyir.com    Data damage of EEPROM     copyir.com
Defective main PWB     copyir.com
Defective engine PWB     copyir.com
C0180    Machine number mismatch error
• Machine number of main PWB and engine PWB does not match     copyir.com    Data damage of EEPROM     copyir.com
C0210    CPU communication problem
• Synchronization cannot be taken between the main CPU and engine CPU     copyir.com    Defective main PWB     copyir.com
Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
C0220    CPU communication problem
• Synchronization cannot be taken between the main CPU and scanner CPU     copyir.com    Defective main PWB     copyir.com
Poor contact in the connector terminals     copyir.com
Defective scanner PWB     copyir.com
C0240    Printer board* communication problem
• The printer board does not respond 120 seconds after the power is turned on     copyir.com    Poor contact in the connector terminals     copyir.com
DIMM installed incorrectly     copyir.com
Defective main PWB or printer board     copyir.com
C0250    Network scanner board* communication problem
• The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more     copyir.com
• The response to the communication command transmitted to the network scanner does not return 75 s or more     copyir.com    Poor contact in the connector terminals     copyir.com
Defective main PWB or network scanner board     copyir.com
C0330    Relay board communication problem    Poor contact in the connector terminals     copyir.com
C0410    DP communication problem
• There is no reply after 5 retries at communication or a communication error occurs     copyir.com    Poor contact in the connector terminals     copyir.com
Defective DP main PWB     copyir.com
C0420    Side feeder* communication error
• A communication error from side feeder is detected 10 times in succession     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
Defective side feeder main PWB     copyir.com
C0440    Document finisher communication problem
• A communication error from document finisher is detected 10 times in succession     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
Defective finisher main PWB     copyir.com
C0460    Duplex unit communication problem
• A communication error from duplex section is detected 10 times in succession     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
Defective duplex PWB     copyir.com
C0500    Paper feed unit communication error (cassette 1 and 2)
• A communication error is detected 10 times in succession     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
C0510    Paper feed unit communication error (cassette 3 and 4)
• A communication error is detected 10 times in succession     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
C0610    Bitmap problem
• The DIMM on the scanner main PWB does not operate correctly     copyir.com    Defective main PWB     copyir.com
C0630    DMA problem
• DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time     copyir.com    Defective main PWB     copyir.com
C0640    Hard disk problem
• The hard disk cannot be accessed     copyir.com    Poor contact in the connector terminals     copyir.com
Defective hard disk     copyir.com
Defective main PWB     copyir.com
Defective cable     copyir.com
C0700    Side feeder EEPROM error
• An error occurs in EEPROM (U4) data read or write for the side feeder main PWB     copyir.com    Defective side feeder main PWB     copyir.com
C0750    Document finisher* EEPROM error
• A backup memory error is received in serial communication data from the finisher     copyir.com    Defective optional document finisher     copyir.com
C0760    Punch unit EEPROM error
• An error occurs in EEPROM data read or write for the punch PWB     copyir.com    Defective punch PWB     copyir.com
C0770    Centerfold unit* EEPROM error
• An error occurs in EEPROM data read or write for the centerfold unit main PWB     copyir.com    Defective centerfold unit main PWB     copyir.com
C0800    Image processing problem
• JAM05 is detected twice     copyir.com    Defective main PWB     copyir.com
C0960    Developing unit EEPROM error
• An error occurs in EEPROM data read or write for the developing unit     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
Defective developing unit     copyir.com
C0970    Cleaning unit EEPROM error
• An error occurs in EEPROM data read or write for the cleaning unit     copyir.com    Poor contact in the connector terminals     copyir.com
Defective engine PWB     copyir.com
Defective cleaning unit     copyir.com
C1010    Lift motor 1 error
• When cassette 1 is inserted, lift limit switch 1 does not turn on within 33 s of lift motor 1 turning on     copyir.com This error is detected four times successively     copyir.com
• During copying, lift limit switch 1 does not turn on within 1 s of lift motor 1 turning on     copyir.com This error is detected four times successively     copyir.com    Broken gears or couplings of lift motor 1     copyir.com
Defective lift motor 1     copyir.com
Poor contact of lift motor 1 connector terminals     copyir.com
Defective lift limit switch 1     copyir.com
Poor contact of lift limit switch 1 connector terminals     copyir.com
Defective deck PWB     copyir.com
C1020    Lift motor 2 error
• When cassette 2 is inserted, lift limit switch 2 does not turn on within 33 s of lift motor 2 turning on     copyir.com This error is detected four times successively     copyir.com
• During copying, lift limit switch 2 does not turn on within 1 s of lift motor 2 turning on     copyir.com This error is detected four times successively     copyir.com    Broken gears or couplings of lift motor 2     copyir.com
Defective lift motor 2     copyir.com
Poor contact of lift motor 2 connector terminals     copyir.com
Defective lift limit switch 2     copyir.com
Poor contact of lift limit switch 2 connector terminals     copyir.com
Defective deck PWB     copyir.com
C1030    Lift motor 3 error
• When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on     copyir.com This error is detected four times successively     copyir.com
• During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on     copyir.com This error is detected four times successively     copyir.com    Broken gears or couplings of lift motor 3     copyir.com
Defective lift motor 3     copyir.com
Poor contact of lift motor 3 connector terminals     copyir.com
Defective lift limit switch 3     copyir.com
Poor contact of lift limit switch 3 connector terminals     copyir.com
Defective casette PWB     copyir.com
C1040    Lift motor 4 error
• When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on     copyir.com This error is detected four times successively     copyir.com
• During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on     copyir.com This error is detected four times successively     copyir.com    Broken gears or couplings of lift motor 4     copyir.com
Defective lift motor 4     copyir.com
Poor contact of lift motor 4 connector terminals     copyir.com
Defective lift limit switch 4     copyir.com
Poor contact of lift limit switch 4 connector terminals     copyir.com
Defective casette PWB     copyir.com
C1140    Side feeder lift motor going up error (optional side feeder)
• Upper limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding)     copyir.com This error is detected four times successively     copyir.com    Poor contact of upper limit detection switch connector terminals     copyir.com
Defective side feeder main PWB     copyir.com
Defective side feeder lift motor     copyir.com
C1150    Side feeder lift motor going down error (optional side feeder)
• Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding)     copyir.com This error is detected four times successively     copyir.com    Poor contact of lower limit detection switch connector terminals     copyir.com
Defective side feeder main PWB     copyir.com
Defective side feeder lift motor     copyir.com
C1200    Duplex side registration motor error
• The duplex side registration home position sensor does not detect the home position of the side registration guide     copyir.com    Defective duplex side registration home position sensor     copyir.com
Defective duplex side registration motor     copyir.com
Defective duplex PWB     copyir.com
C2100    Developing motor error
• LOCK signal remains high for 1 s, 1 s after the developing motor has turned on     copyir.com    Poor contact in the developing motor connector terminals     copyir.com
Defective developing motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective duplex PWB     copyir.com
C2200    Drive motor error
• LOCK signal remains high for 1 s, 1 s after the drive motor has turned on     copyir.com    Poor contact in the drive motor connector terminals     copyir.com
Defective drive motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective deck PWB or engine PWB     copyir.com
C2250    Cleaning motor error
• LOCK signal remains high for 1 s, 200 ms after the cleaning motor has turned on     copyir.com    Poor contact in the drive motor connector terminals     copyir.com
Defective cleaning motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective engine PWB     copyir.com
C2300    Fuser motor error
• LOCK signal remains high for 1 s, 1 s after the fuser motor has turned on     copyir.com    Poor contact in the fuser motor connector terminals     copyir.com
Defective fuser motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective duplex PWB or engine PWB     copyir.com
C2550    Transfer motor error
• LOCK signal remains high for 1 s, 1 s after the transfer motor has turned on     copyir.com    Poor contact in the transfer motor connector terminals     copyir.com
Defective transfer motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective cassette PWB or engine PWB     copyir.com
C2640    Side feeder drive motor error    Overloaded side feeder drive motor
Defective side feeder drive motor     copyir.com
Defective side feeder main PWB     copyir.com
C2720    PTC cleaning motor error
• LOCK signal remains high for 1 s, 200 ms after the PTC cleaning motor has turned on     copyir.com    Poor contact in the drive motor connector terminals     copyir.com
Defective PTC cleaning motor rotation control circuit     copyir.com
Defective drive transmission system     copyir.com
Defective engine PWB     copyir.com
C3100    Scanner carriage problem
• The home position is not correct when the power is turned on or at the start of copying using the MP tray     copyir.com    Defective scanner PWB     copyir.com
Defective scanner home position switch     copyir.com
Defective scanner motor     copyir.com
Poor contact in the connector terminals     copyir.com
Defective mirror flame, exposure lamp or scanner wire     copyir.com
C3200    Exposure lamp problem
• Check the CCD input value for the lighting status of the exposure lamp 500 ms after the exposure lamp is lit and the carriage is moved to the shading position     copyir.com If the exposure lamp does not light, a further 100 ms later, check the CCD input     copyir.com The exposure lamp does not light after 50 retries     copyir.com    Defective scanner PWB     copyir.com
Defective exposure lamp or inverter PWB     copyir.com
Incorrect shading position     copyir.com
Poor contact of the connector terminals     copyir.com
Defective CCD PWB     copyir.com
C3210    CIS lamp problem
• After the reading starting, when input value at the time of CIS illumination does not exceed the threshold value between 5 s     copyir.com    Defective DP main PWB     copyir.com
Poor contact in the connector terminals     copyir.com
Defective CIS     copyir.com
Defective DP inverter PWB     copyir.com
C3300    Optical system (AGC) problem
• After AGC, correct input is not obtained at CCD     copyir.com    Insufficient exposure lamp luminosity     copyir.com
Defective scanner PWB     copyir.com
Incorrect shading position     copyir.com
CCD PWB output problem     copyir.com
Poor contact of the connector terminals     copyir.com
C3310    CIS (AGC) problem
• After AGC, correct input is not obtained at CIS     copyir.com    Defective DP main PWB     copyir.com
CIS output problem     copyir.com
Defective DP inverter PWB     copyir.com
C3500    Communication error between scanner and SHD
• An error code is detected     copyir.com    Defective SHD PWB     copyir.com
Poor contact in the connector terminals     copyir.com
Defective scanner PWB     copyir.com
C3900    Backup memory read/write error (scanner PWB)
• Read and write data does not match     copyir.com    Defective back up RAM or scanner PWB     copyir.com
C3910    Backup memory read/write error (scanner PWB)
• Data in the specified area of the backup memory does not match the specified values     copyir.com    Problem with the backup memory data     copyir.com
Defective scanner PWB     copyir.com
C4000    Polygon motor synchronization problem
• The revolution does not reach the stable speed within 20 s of the START signal     copyir.com    Poor contact in the polygon motor connector terminals     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
C4010    Polygon motor steady-state problem
• The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized     copyir.com    Poor contact in the polygon motor connector terminals     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
C4100    BD initialization (A) problem
• When power is turned on, only laser A is output and ASIC of main PWB detects a BD error for 2000 ms     copyir.com    Defective laser scanner unit     copyir.com
Defective main PWB     copyir.com
Poor contact in connector terminals     copyir.com
C4110    BD initialization (B) problem
• When power is turned on, only laser B is output and ASIC of main PWB detects a BD error for 2000 ms     copyir.com    Defective laser scanner unit     copyir.com
Defective main PWB     copyir.com
Poor contact in connector terminals     copyir.com
C4120    BD initialization (C) problem
• When power is turned on, only laser C is output and ASIC of main PWB detects a BD error for 2000 ms     copyir.com    Defective laser scanner unit     copyir.com
Defective main PWB     copyir.com
Poor contact in connector terminals     copyir.com
C4200    BD steady-state problem
• ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized     copyir.com    Defective laser diode     copyir.com
Defective polygon motor     copyir.com
Defective main PWB     copyir.com
Poor contact in connector terminals     copyir.com
C5100    Main high-voltage error
• While the main high-voltage output remote signal is on, an alarm signal is detected continuously for 400 ms     copyir.com    Defective high voltage PWB     copyir.com
Leak of main high-voltage     copyir.com
Poor contact in connector terminals     copyir.com
C5500    Drum surface potential sensor problem 1
• The sensor output is 0     copyir.com5 V or less when MC REM signal is turned on     copyir.com    Poor contact in the drum surface potential sensor connector terminals     copyir.com
Defective drum surface potential sensor     copyir.com
Defective high voltage PWB     copyir.com
Defective engine PWB     copyir.com
C5510    Drum surface potential sensor problem 2
• The sensor output is 4     copyir.com5 V or more when the MC REM signal is turned on     copyir.com    Defective drum surface potential sensor     copyir.com
Defective high voltage PWB     copyir.com
Poor contact in the drum surface potential sensor     copyir.com
C5600    Drum surface potential problem 1
• The sensor output is 4     copyir.com5 V or more     copyir.com
• Potential adjustment in 30 times could not raise the potential sensor value to the predetermined     copyir.com    Deteriorated main charger     copyir.com
Grid or main charger shield is dirty     copyir.com
Defective drum surface potential sensor     copyir.com
Defective high voltage PWB     copyir.com
Defective engine PWB     copyir.com
C5610    Drum surface potential problem 2
• The sensor output is 0     copyir.com5 V or less     copyir.com
• Potential adjustment in 30 times could not lower the potential sensor value to the predetermined     copyir.com    Defective drum surface potential sensor     copyir.com
Defective high voltage PWB     copyir.com
Defective drum     copyir.com
Defective engine PWB     copyir.com
C6000    Fuser heater lamp break
• The fuser temperature does not increase for 40 s after the fuser heaters have been turned on for warming up     copyir.com
• The fuser temperature remains below 50C/122F for 10 s continuously after the fuser heaters have been turned on during stabilization     copyir.com    Installation defectiveness on fuser thermistor M and S     copyir.com
Defective fuser thermostat 1 or 2     copyir.com
Installation defectiveness on fuser heater L, M or S     copyir.com
Broken fuser heater L, M and S wire     copyir.com
Defective engine PWB
Defective AC power source PWB     copyir.com
C6020    Fuser thermistor high-temperature detection error
• The fuser temperature exceeds 235C/455 F for 10 s     copyir.com    Installation defectiveness on fuser thermistor M and S     copyir.com
Defective fuser thermistor M and S     copyir.com
Defective engine PWB     copyir.com
C6030    Fuser thermistor break error
• The fuser temperature remains at lower then 0C/32F for 30 s continuously when the fuser heater is on     copyir.com    Defective engine PWB     copyir.com
Defective AC power source PWB     copyir.com
Installation defectiveness on fuser thermistor M and S     copyir.com
C6050    Fuser thermistor abnormal temperature detection • During copying, the temperature at the heat roller lower than 120C/248F is detected continuously for 5 s     copyir.com    Installation defectiveness on fuser thermistor M and S     copyir.com
Operation on fuser thermostat 1 or 2     copyir.com
Installation defectiveness on fuser heater L, M or S     copyir.com
Broken fuser heater L, M and S wire     copyir.com
Defective engine PWB     copyir.com
Defective AC power source PWB     copyir.com
C6400    Zero-cross signal error
• The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s     copyir.com    Poor contact in the connector terminals     copyir.com
Defective DC power source PWB     copyir.com
Defective engine PWB
C7200    Broken internal thermistor wire
• The thermistor output value is 4     copyir.com5 V or more     copyir.com    Poor contact in the connector terminals     copyir.com
Defective developing humidity sensor     copyir.com
Defective engine PWB     copyir.com
C7210    Short-circuited internal thermistor
• The thermistor input value is 0     copyir.com5 V or less     copyir.com    Poor contact in the connector terminals     copyir.com
Defective developing humidity sensor     copyir.com
Defective engine PWB     copyir.com
C7300    Toner hopper problem
• During toner replenishment after toner empty has been detected, toner empty could not be cleared in 3 times of 360 s     copyir.com    Defective toner level detection sensor     copyir.com
Poor contact in the toner level detection sensor connector terminals     copyir.com
C7800    Broken external thermistor wire
• The thermistor output value is 4     copyir.com5 V or more     copyir.com    Poor contact in the connector terminals     copyir.com
Defective humidity sensor     copyir.com
C7810    Short-circuited external thermistor
• The thermistor input value is 0     copyir.com5 V or less     copyir.com    Poor contact in the connector terminals     copyir.com
Defective humidity sensor     copyir.com
Defective engine PWB
C8000    Fnisher type mismatch problem
• Absence of the finisher is detected     copyir.com    Different type of the finisher is installed     copyir.com
C8010    Document finisher paper conveying motor problem
• The LOCK signal of the paper conveying motor is detected for more than 500 ms while the paper conveying motor is operating     copyir.com However, the first 1 s after the paper conveying motor is turned on is excluded from detection     copyir.com    Loose connection of the paper conveying motor connector     copyir.com
Defective paper conveying motor     copyir.com
Defective finisher main PWB     copyir.com
C8020    Document finisher punch motor problem
• The LOCK signal of the punch motor is detected for more than 500 ms while the punch motor is operating     copyir.com However, the first 1 s after the punch motor is turned on is excluded from detection     copyir.com    Loose connection of the punch motor connector     copyir.com
Defective punch motor     copyir.com
Defective finisher main PWB     copyir.com
C8030    Document finisher upper paper conveying belt problem
• During initialization, the intermediate tray upper sliding plate is not detected in the home position within 3 s after the belt returns to the home position     copyir.com JAM87 is indicated the first time this problem occurs     copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the upper paper conveying belt     copyir.com • When the intermediate tray upper sliding plate is operated from the home position, the upper paper conveying belt home position sensor does not turn off within 1 s     copyir.com    Phase shift of the upper paper conveying belt     copyir.com
Malfunction of the upper paper conveying belt motor     copyir.com
Malfunction of the upper paper conveying belt home position sensor     copyir.com
Loose connection of the upper paper conveying belt home position sensor connector     copyir.com
Incorrect insertion of the intermediate tray     copyir.com
Defective finisher main PWB
C8040    Document finisher lower paper conveying belt problem
• During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position     copyir.com JAM87 is indicated the first time this problem occurs     copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt     copyir.com • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s     copyir.com    Phase shift of the lower paper conveying belt     copyir.com
Malfunction of the lower paper conveying belt motor     copyir.com
Malfunction of the lower paper conveying belt home position sensor     copyir.com
Loose connection of the lower paper conveying belt home position sensor connector     copyir.com
Incorrect insertion of the intermediate tray     copyir.com
Defective finisher main PWB     copyir.com
C8140    Document finisher main tray problem
• When the main tray is not detected by the main tray upper limit detection sensor or the main tray load detection sensor within 20 s from the moment it starts ascending     copyir.com
• During main tray descent, the main tray upper limit detection sensor or the main tray load detection sensor does not turn off within 500 ms after it turns on     copyir.com
• During main tray ascent, the main tray upper limit detection sensor or the main tray load detection sensor stays on for more than 2 s     copyir.com    Loose connection of the main tray elevation motor connector     copyir.com
Malfunction of the main tray elevation motor     copyir.com
Malfunction of the main tray upper limit detection sensor     copyir.com
Loose connection of the main tray upper limit detection sensor connector     copyir.com
Malfunction of the main tray load detection sensor     copyir.com
Loose connection of the main tray load detection sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8150    Document finisher multi job tray problem
• When the multi job tray is not detected by the multi job tray upper limit detection sensor within 20 s from the moment it starts ascending     copyir.com
• During multi job tray descent, the multi job tray upper limit detection sensor does not turn off within 500 ms after it turns on     copyir.com    Loose connection of the multi job tray elevation motor connector     copyir.com
Malfunction of the multi job tray elevation motor     copyir.com
Malfunction of the multi job tray upper limit detection sensor     copyir.com
Loose connection of the multi job tray upper limit detection sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8170    Document finisher front upper side registration guide problem
• During initialization, the front upper side registration guide is not detected in the home position within 3 s after the guide returns to the home position     copyir.com JAM87 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front upper side registration guide     copyir.com
• When the front upper side registration guide is operated from the home position, the front upper side registration home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the front upper side registration guide motor connector     copyir.com
Malfunction of the front upper side registration guide motor     copyir.com
Malfunction of the front upper side registration guide home position sensor     copyir.com
Loose connection of the front upper side registration guide home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8180    Document finisher rear upper side registration guide problem
• During initialization, the rear upper side registration guide is not detected in the home position within 3 s after the guide returns to the home position     copyir.com JAM87 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear upper side registration guide     copyir.com
• When the rear upper side registration guide is operated from the home position, the rear upper side registration home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the rear upper side registration guide motor connector     copyir.com
Malfunction of the rear upper side registration guide motor     copyir.com
Malfunction of the rear upper side registration guide home position sensor     copyir.com
Loose connection of the rear upper side registration guide home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8190    Document finisher lower side registration guide problem
• During initialization, the front/rear lower side registration guides are not detected in the home position within 3 s after the guide returns to the home position     copyir.com JAM87 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the lower side registration guide     copyir.com
• When the lower side registration guide is operated from the home position, the lower side registration home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the lower side registration guide motor connector     copyir.com
Malfunction of the lower side registration guide motor     copyir.com
Malfunction of the lower side registration guide home position sensor     copyir.com
Loose connection of the lower side registration guide home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8210    Document finisher front stapler problem
• During initialization, the front stapler is not detected in the home position within 500 ms after the front stapler returns to the home position     copyir.com JAM90 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front stapler     copyir.com
• When the front stapler is operated from the home position, the front stapler home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the front stapler motor connector     copyir.com
Malfunction of the front stapler motor     copyir.com
Malfunction of the front stapler home position sensor     copyir.com
Loose connection of the front stapler home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8220    Document finisher* front clincher problem
• During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position     copyir.com JAM90 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher     copyir.com
• When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the front clincher motor connector     copyir.com
Malfunction of the front clincher motor     copyir.com
Malfunction of the front clincher home position sensor     copyir.com
Loose connection of the front clincher home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8230    Document finisher rear stapler problem
• During initialization, the rear stapler is not detected in the home position within 500 ms after the rear stapler returns to the home position     copyir.com JAM90 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear stapler     copyir.com
• When the rear stapler is operated from the home position, the rear stapler home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the rear stapler motor connector
Malfunction of the rear stapler motor     copyir.com
Malfunction of the rear stapler home position sensor     copyir.com
Loose connection of the rear stapler home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8240    Document finisher rear clincher problem
• During initialization, the rear clincher is not detected in the home position within 500 ms after the rear clincher returns to the home position     copyir.com JAM90 is indicated the first time this problem occurs     copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear clincher     copyir.com
• When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn off within 500 ms     copyir.com    Loose connection of the rear clincher motor connector     copyir.com
Malfunction of the rear clincher motor     copyir.com
Malfunction of the rear clincher home position sensor     copyir.com
Loose connection of the rear clincher home position sensor connector     copyir.com
Defective finisher main PWB     copyir.com
C8300    Document finisher centerfold unit communication problem
• Communication with the centerfold unit is not possible although the connection is detected     copyir.com    Loose connection of the centerfold unit set switch connector     copyir.com
Defective centerfold unit set switch     copyir.com
Defective centerfold unit main PWB     copyir.com
Defective finisher main PWB     copyir.com
C8310    Document finisher centerfold unit side registration guide problem
• During initialization, the front/rear side registration guides are not detected in the home position within 600 ms after the guide returns to the home position     copyir.com
• When the side registration guide is operated from the home position, the side registration guide home position sensor does not turn off within 100 ms     copyir.com    Loose connection of the side registration guide motor connector     copyir.com
Malfunction of the side registration guide motor     copyir.com
Malfunction of the side registration guide home position sensor     copyir.com
Loose connection of the side registration guide home position sensor connector     copyir.com
Defective centerfold unit main PWB     copyir.com
C8320    Document finisher centerfold unit centering plate problem
• During initialization, the centering plate is not detected in the home position when the centering plate returns to the home position     copyir.com    Loose connection of the centering plate motor connector     copyir.com
Malfunction of the centering plate motor     copyir.com
Malfunction of the centering plate home position sensor     copyir.com
Loose connection of the centering plate home position sensor connector     copyir.com
Defective centerfold unit main PWB     copyir.com
C8330    Document finisher centerfold blade problem
• During initialization, the centerfold blade is not detected in the home position within a specified period of time     copyir.com    Loose connection of the centerfold blade motor connector     copyir.com
Malfunction of the centerfold blade motor     copyir.com
Malfunction of the centerfold blade home position sensor     copyir.com
Loose connection of the centerfold blade home position sensor connector     copyir.com
Defective centerfold unit main PWB     copyir.com
C9040    DP lift motor going up error
• The pulse count raised to 10000 at lifting, however, the DP lift upper limit switch could not be turned on     copyir.com After one time retry, the DP lift upper limit switch could not be turned on     copyir.comme     copyir.com    Loose connection of the DP lift motor connector     copyir.com
Malfunction of the DP lift motor     copyir.com
Malfunction of the DP lift upper limit switch     copyir.com
Loose connection of the DP lift upper limit switch connector     copyir.com
Defective DP main PWB     copyir.com
C9050    DP lift motor going down error
• The pulse count raised to 10000 at lifting, however, the DP lift lower limit switch could not be turned on     copyir.com After one time retry, the DP lift lower limit switch could not be turned on     copyir.comme     copyir.com    Loose connection of the DP lift motor connector     copyir.com
Malfunction of the DP lift motor     copyir.com
Malfunction of the DP lift lower limit switch     copyir.com
Loose connection of the DP lift lower limit switch connector     copyir.com
Defective DP main PWB     copyir.com
C9060    DP EEPROM error
• Read and write data does not match     copyir.com
• Data in the specified area of the backup memory does not match the specified values     copyir.com    Defective DP main PWB     copyir.com
Device damage of EEPROM     copyir.com
C9070    Communication problem between DP and SHD
• A communication error is detected     copyir.com    Loose connection of the SHD PWB     copyir.com
Defective SHD PWB     copyir.com
Defective DP main PWB     copyir.com
C9080    Communication problem between DP and CIS
A communication error is detected     copyir.com    Loose connection of CIS     copyir.com
Defective CIS     copyir.com

نماد اعتماد

اطلاعات تماس

 آدرس: آذربایجان شرقی، مراغه، خیایان امام، روبروی داروخانه جاوید، ساختمان کپی ایران
شماره تماس: 04137252392   |    04137254200
شماره تماس: 04137253033   |   04137253034
شماره همراه: 09148659399
شماره فکس: 04136586892
پست الکترونیکی: این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید.این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت دارید|این آدرس ایمیل توسط spambots حفاظت می شود. برای دیدن شما نیاز به جاوا اسکریپت داریدساعات کاری: از 8 الی 22 شب