
از سرویس مانوئل کیوسرا میتا (342)
کیو سرا میتا Kyocera-Mita TASKalfa 8000i
نوشته شده توسط ایراندوست بهزاد0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory copyir.com
Defective engine PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Improper installation EEPROM copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error
(engine PWB) Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0620 FAX image DIMM error
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com
Defective main PWB copyir.com
0650 FAX image DIMM check error
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0900 FAX software incompatible detection error
Incompatible FAX control PWB is installed copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0970 12 V power down detect
Power is disconnected during sleeping copyir.com Defective power source PWB copyir.com
0980 24 V power down detect
24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected copyir.com Defective power source PWB copyir.com
1000 MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 1 copyir.com5 s copyir.com Defective MP plate elevation mechanism copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective MP lift motor copyir.com
Defective engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective lift motor 1 copyir.com
Defective engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 2 copyir.com
Defective engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1050 SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM lift motor copyir.com
Defective SM main PWB copyir.com
1060 PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1070 PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD lift motor copyir.com
Defective SD main PWB copyir.com
1250 SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
The SM multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1400 BR guide motor error
The BR decurler sensor won’t turn on three times in a row after the home position of the rotary guide has been detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR guide motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1410 BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR decurler motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1710 Side multi tray incompatible detection error
The side multi tray has been installed with a device to which it is incompatible copyir.com The side multi tray is installed with a device to which it is incompatible copyir.com
1720 Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible copyir.com The paper feeder is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1810 Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1820 Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1910 Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective SM main PWB copyir.com
Device damage of EEPROM copyir.com
1920 Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1950 Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer belt unit copyir.com
2101 Developer motor K error
After developer motor K is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor K copyir.com
Defective engine PWB copyir.com
2102 Developer motor C error
After developer motor C is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor C copyir.com
Defective engine PWB copyir.com
2103 Developer motor M error
After developer motor M is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor M is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor M copyir.com
Defective engine PWB copyir.com
2104 Developer motor Y error
After developer motor Y is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor Y is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor Y copyir.com
Defective engine PWB
2201 Drum motor K steady-state error
After drum motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2202 Drum motor C steady-state error
Drum motor C does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2203 Drum motor M steady-state error
Drum motor M does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2204 Drum motor Y steady-state error
Drum motor Y does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2212 Drum motor C startup error
Drum motor C is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2213 Drum motor M startup error
Drum motor M is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2214 Drum motor Y startup error
Drum motor Y is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2231 Drum motor K main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB
2232 Drum motor C main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2233 Drum motor M main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2234 Drum motor Y main sensor error No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2241 Drum motor K sub sensor error
No signal is input to the sensor for 100 ms continuously Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2242 Drum motor C sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2243 Drum motor M sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2244 Drum motor Y sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2550 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
2600 PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2640 SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD paper feed motor
Defective SD main PWB copyir.com
2650 SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM paper feed motor copyir.com
Defective SM main PWB copyir.com
2660 PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2670 PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2700 Color release motor error
When the color release motor is driven, the color release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective color release motor copyir.com
Defective engine PWB copyir.com
2730 Transfer release motor error
When the transfer release motor is driven, the transfer release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer release motor copyir.com
Defective engine PWB copyir.com
2760 Transfer motor startup error
Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2770 Transfer skew error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2780 Transfer skew sensor error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2790 Transfer skew motor error
When the transfer skew motor is driven, timeouts were detected twice in a row copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer skew motor copyir.com
Defective engine PWB copyir.com
2810 Waste toner motor error
Initialized when an error is constantly observed for 2 seconds after the waste toner motor is activated copyir.com An error is constantly observed for 2 copyir.com5 seconds after rebooting copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective waste toner motor copyir.com
Defective engine PWB copyir.com
2820 Transfer motor steady-state error Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2840 Transfer cleaning motor error
After transfer cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com
After transfer cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer cleaning motor copyir.com
Defective engine PWB copyir.com
2850 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2860 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2950 Motor control PWB communication error
A communication error from the motor control PWB is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor control PWB copyir.com
Defective engine PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective scanner motor copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LED lamp PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3300 Optical system (AGC) error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp copyir.com
Defective CCD PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3310 CIS AGC error
After AGC, correct input is not obtained at CIS copyir.com Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3500 Communication error between scanner and ASIC An error code is detected copyir.com Defective connector cable or poor contact in the connector
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective ISC PWB copyir.com
3700 Scanner device error CCD connector inserted incorrectly copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective ISC PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Defective backup memory or PWB copyir.com
4001 Polygon motor K synchronization error
After polygon motor K is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4002 Polygon motor C synchronization error
After polygon motor C is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4003 Polygon motor M synchronization error
After polygon motor M is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4004 Polygon motor Y synchronization error
After polygon motor Y is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4011 Polygon motor K steady-state error
After polygon motor K is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4012 Polygon motor C steady-state error
After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4013 Polygon motor M steady-state error
After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4014 Polygon motor Y steady-state error
After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4101 BD initialization error K
After polygon motor K is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4102 BD initialization error C
After polygon motor C is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4103 BD initialization error M
After polygon motor M is driven, ASIC detects a BD error for 1 s Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4104 BD initialization error Y
After polygon motor Y is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB copyir.com
4201 BD steady-state error K
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4202 BD steady-state error C
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4203 BD steady-state error M
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4204 BD steady-state error Y
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB
4300 Polygon motor phase error
ASIC won’t settle in completion of phase adjustment for 2 seconds after a BD signal is detected copyir.com Defective laser scanner unit copyir.com
Defective engine PWB copyir.com
4600 LSU cleaning motor error
After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective LSU cleaning motor copyir.com
Defective engine PWB copyir.com
5101 Main high-voltage error K
Abnormality of charger roller K is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5102 Main high-voltage error C
Abnormality of charger roller C is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5103 Main high-voltage error M
Abnormality of charger roller M is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5104 Main high-voltage error Y
Abnormality of charger roller Y is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 1 detects a temperature higher than 190°C/374°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB copyir.com
6130 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature lower than 30°C/ 86°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 250°C/482°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 2 copyir.com
Defective engine PWB copyir.com
6230 Broken fuser thermistor 2 wire
Input from fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 2 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 2 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6320 Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 3 copyir.com
Defective engine PWB copyir.com
6330 Broken fuser thermistor 3 wire
Input from fuser thermistor 3 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 3 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6520 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 240C/464F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB
6530 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 second copyir.com (Engine CPU) Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB copyir.com
6610 Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser release motor copyir.com
Defective engine PWB copyir.com
6620 IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective IH core motor copyir.com
Defective front PWB copyir.com
Defective engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6720 Fuser IH belt rotation error
A belt rotating pulse is not received for 1 second copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB
6730 Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6750 Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6760 Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6770 Fuser IH low electric power error
The preset power is less than 0 copyir.com6 times of it for 120 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6780 Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6900 Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser front fan motor copyir.com
Defective engine PWB
6910 Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser rear fan motor copyir.com
Defective engine PWB copyir.com
6920 Fuser edge fan motor 1 error
When the fuser edge fan motor 1 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 1 copyir.com
Defective engine PWB copyir.com
6930 Fuser edge fan motor 2 error
When the fuser edge fan motor 2 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 2 copyir.com
Defective engine PWB copyir.com
6940 IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH fan motor copyir.com
Defective engine PWB copyir.com
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6960 Current PWB error
Less than 1A is continuously observed for 5 seconds copyir.com Defective current PWB copyir.com
6990 Fuser power supply incompatibility
Information won’t match between the engine backup and the fuser IH PWB copyir.com Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
7001 Toner motor K error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor K is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor K copyir.com
Defective toner motor K copyir.com
Defective engine PWB copyir.com
7002 Toner motor C error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor C is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor C copyir.com
Defective toner motor C copyir.com
Defective engine PWB copyir.com
7003 Toner motor M error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor M is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor M copyir.com
Defective toner motor M copyir.com
Defective engine PWB copyir.com
7004 Toner motor Y error A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor Y is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor Y copyir.com
Defective toner motor Y copyir.com
Defective engine PWB copyir.com
7101 Toner sensor K error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7102 Toner sensor C error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7103 Toner sensor M error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7104 Toner sensor Y error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7210 Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7221 Broken LSU thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7222 Broken LSU thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C copyir.com
Defective engine PWB copyir.com
7223 Broken LSU thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7224 Broken LSU thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7231 Short-circuited LSU thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7232 Short-circuited LSU thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C
Defective engine PWB copyir.com
7233 Short-circuited LSU thermistor M The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7234 Short-circuited LSU thermistor Y
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7241 Broken developer thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB copyir.com
7242 Broken developer thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7243 Broken developer thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor M copyir.com
Defective engine PWB copyir.com
7244 Broken developer thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7251 Short-circuited developer thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB
7252 Short-circuited developer thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7253 Short-circuited developer thermistor M
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor M copyir.com
Defective engine PWB
7254 Short-circuited developer thermistor Y wire
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7301 Toner hopper motor K error
When the toner hopper motor K is driven, toner hopper sensor K does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor K copyir.com
Defective toner hopper motor K copyir.com
Defective engine PWB copyir.com
7302 Toner hopper motor C error
When the toner hopper motor C is driven, toner hopper sensor C does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor C copyir.com
Defective toner hopper motor C copyir.com
Defective engine PWB copyir.com
7303 Toner hopper motor M error
When the toner hopper motor M is driven, toner hopper sensor M does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor M copyir.com
Defective toner hopper motor M copyir.com
Defective engine PWB copyir.com
7304 Toner hopper motor Y error
When the toner hopper motor Y is driven, toner hopper sensor Y does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor Y copyir.com
Defective toner hopper motor Y copyir.com
Defective engine PWB copyir.com
7401 Developer unit K type mismatch error
Absence of the developer unit K is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7402 Developer unit C type mismatch error
Absence of the developer unit C is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7403 Developer unit M type mismatch error
Absence of the developer unit M is detected copyir.com Defective connector cable or poor contact in the connector
Different type of the developer unit is installed
7404 Developer unit Y type mismatch error
Absence of the developer unit Y is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com
Defective connector cable or poor contact in the connector copyir.com
7601 ID sensor 1 error
An abnormal value is detected in the input data to ID sensor 1 copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7602 ID sensor 2 error
An abnormal value is detected in the input data to ID sensor 2 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7800 Broken outer temperature sensor 1 wire
The sensor input sampling is greater than 255 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7810 Short-circuited outer temperature sensor 1
The sensor input sampling is less than 0 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB K copyir.com
7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB C copyir.com
7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB M copyir.com
7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB Y copyir.com
7911 Developer unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit K copyir.com
7912 Developer unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit C copyir.com
7913 Developer unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit M copyir.com
7914 Developer unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit Y copyir.com
7941 Laser scanner unit K EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB K copyir.com
7942 Laser scanner unit C EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB C copyir.com
7943 Laser scanner unit M EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB M copyir.com
7944 Laser scanner unit Y EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB Y copyir.com
8000 Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible copyir.com The finisher is installed with a device to which it is incompatible copyir.com
8010 Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch home position sensor copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8020 Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8030 Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF paddle sensor
Defective DF paddle motor copyir.com
Defective DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF bundle discharge sensor copyir.com
Defective DF eject release motor copyir.com
Defective DF main PWB copyir.com
8110 DF shift motor 1 error
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector
Defective DF shift sensor 1 copyir.com
Defective DF shift motor 1 copyir.com
Defective DF main PWB copyir.com
8120 DF shift motor 2 error
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 2 copyir.com
Defective DF shift motor 2 copyir.com
Defective DF main PWB copyir.com
8130 DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift release sensor copyir.com
Defective DF shift release motor copyir.com
Defective DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray sensor 3 copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF slide motor copyir.com
Defective DF main PWB copyir.com
8230 DF staple motor error 1
JAM7000 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8240 DF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8250 DF tray motor error 4
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8300 Center-folding unit communication error
Communication with the center-folding unit is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF set sensor copyir.com
Defective PWB copyir.com
8310 CF side registration motor 2 error
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 2 copyir.com
Defective CF side registration motor 2 copyir.com
Defective CF main PWB copyir.com
8320 CF adjustment motor error
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF adjustment sensor 1, 2 copyir.com
Defective CF adjustment motor 1, 2 copyir.com
Defective CF main PWB copyir.com
8330 CF blade motor error
When initial operation, CF blade sensor does not turn on within 1 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF blade sensor copyir.com
Defective CF blade motor copyir.com
Defective CF main PWB copyir.com
8340 CF staple motor error 1
JAM7600 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple sensor copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8350 CF side registration motor 1 error
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 1 copyir.com
Defective CF side registration motor 1 copyir.com
Defective CF main PWB copyir.com
8360 CF main motor error
During driving the motor, lock signal is detected for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF main motor
Defective CF main PWB copyir.com
8370 CF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective slide sensor copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8500 Mailbox communication error
Communication with the mailbox is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8510 MB conveying motor error 1
When initial operation, MB home position sensor does not turn on within 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8520 MB conveying motor error 2
When standby operation, MB home position sensor does not turn off within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8800 Document finisher communication error
Communication with the document finisher is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Improper installation EEPROM copyir.com
Defective DF main PWB copyir.com
8930 Center-folding unit backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM
Defective CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com Defective connector cable or poor contact in the connector
Defective PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Data setup failure copyir.com
Defective coin vender control PWB copyir.com
Defective PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector
Defective DP lift sensor 1 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 2 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DPSHD PWB copyir.com
9080 LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Defective coin vender control PWB copyir.com
9110 Coin vender error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector installed incorrectly copyir.com
Defective rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Defective pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Change jam at the pay-out copyir.com
Defective pay-out motor copyir.com
Defective pay-out sensor copyir.com
9200 DP multi feed sensor communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
9210 DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9220 DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9500, 9510, 9520, 9530, 9540, 9550 Contact the Service Administrative Division copyir.com
F000 Communication error between main PWB and operation PWB Defective main PWB copyir.com
Defective operation PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F040 Communication error between main PWB and print engine Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Communication error between main PWB and scanner engine Defective main PWB copyir.com
Defective ISC PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective ISC PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
کیو سرا میتا Kyocera-Mita TASKalfa 7550ci
نوشته شده توسط ایراندوست بهزاد0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory copyir.com
Defective engine PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Improper installation EEPROM copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error
(engine PWB) Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0620 FAX image DIMM error
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com
Defective main PWB copyir.com
0650 FAX image DIMM check error
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0900 FAX software incompatible detection error
Incompatible FAX control PWB is installed copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0970 12 V power down detect
Power is disconnected during sleeping copyir.com Defective power source PWB copyir.com
0980 24 V power down detect
24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected copyir.com Defective power source PWB copyir.com
1000 MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 1 copyir.com5 s copyir.com Defective MP plate elevation mechanism copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective MP lift motor copyir.com
Defective engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective lift motor 1 copyir.com
Defective engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 2 copyir.com
Defective engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1050 SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM lift motor copyir.com
Defective SM main PWB copyir.com
1060 PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1070 PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD lift motor copyir.com
Defective SD main PWB copyir.com
1250 SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
The SM multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1400 BR guide motor error
The BR decurler sensor won’t turn on three times in a row after the home position of the rotary guide has been detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR guide motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1410 BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR decurler motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1710 Side multi tray incompatible detection error
The side multi tray has been installed with a device to which it is incompatible copyir.com The side multi tray is installed with a device to which it is incompatible copyir.com
1720 Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible copyir.com The paper feeder is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1810 Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1820 Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1910 Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective SM main PWB copyir.com
Device damage of EEPROM copyir.com
1920 Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1950 Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer belt unit copyir.com
2101 Developer motor K error
After developer motor K is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor K copyir.com
Defective engine PWB copyir.com
2102 Developer motor C error
After developer motor C is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor C copyir.com
Defective engine PWB copyir.com
2103 Developer motor M error
After developer motor M is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor M is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor M copyir.com
Defective engine PWB copyir.com
2104 Developer motor Y error
After developer motor Y is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor Y is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor Y copyir.com
Defective engine PWB
2201 Drum motor K steady-state error
After drum motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2202 Drum motor C steady-state error
Drum motor C does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2203 Drum motor M steady-state error
Drum motor M does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2204 Drum motor Y steady-state error
Drum motor Y does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2212 Drum motor C startup error
Drum motor C is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2213 Drum motor M startup error
Drum motor M is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2214 Drum motor Y startup error
Drum motor Y is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2231 Drum motor K main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB
2232 Drum motor C main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2233 Drum motor M main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2234 Drum motor Y main sensor error No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2241 Drum motor K sub sensor error
No signal is input to the sensor for 100 ms continuously Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2242 Drum motor C sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2243 Drum motor M sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2244 Drum motor Y sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2550 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
2600 PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2640 SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD paper feed motor
Defective SD main PWB copyir.com
2650 SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM paper feed motor copyir.com
Defective SM main PWB copyir.com
2660 PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2670 PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2700 Color release motor error
When the color release motor is driven, the color release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective color release motor copyir.com
Defective engine PWB copyir.com
2730 Transfer release motor error
When the transfer release motor is driven, the transfer release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer release motor copyir.com
Defective engine PWB copyir.com
2760 Transfer motor startup error
Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2770 Transfer skew error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2780 Transfer skew sensor error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2790 Transfer skew motor error
When the transfer skew motor is driven, timeouts were detected twice in a row copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer skew motor copyir.com
Defective engine PWB copyir.com
2810 Waste toner motor error
Initialized when an error is constantly observed for 2 seconds after the waste toner motor is activated copyir.com An error is constantly observed for 2 copyir.com5 seconds after rebooting copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective waste toner motor copyir.com
Defective engine PWB copyir.com
2820 Transfer motor steady-state error Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2840 Transfer cleaning motor error
After transfer cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com
After transfer cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer cleaning motor copyir.com
Defective engine PWB copyir.com
2850 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2860 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2950 Motor control PWB communication error
A communication error from the motor control PWB is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor control PWB copyir.com
Defective engine PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective scanner motor copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LED lamp PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3300 Optical system (AGC) error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp copyir.com
Defective CCD PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3310 CIS AGC error
After AGC, correct input is not obtained at CIS copyir.com Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3500 Communication error between scanner and ASIC An error code is detected copyir.com Defective connector cable or poor contact in the connector
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective ISC PWB copyir.com
3700 Scanner device error CCD connector inserted incorrectly copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective ISC PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Defective backup memory or PWB copyir.com
4001 Polygon motor K synchronization error
After polygon motor K is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4002 Polygon motor C synchronization error
After polygon motor C is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4003 Polygon motor M synchronization error
After polygon motor M is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4004 Polygon motor Y synchronization error
After polygon motor Y is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4011 Polygon motor K steady-state error
After polygon motor K is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4012 Polygon motor C steady-state error
After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4013 Polygon motor M steady-state error
After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4014 Polygon motor Y steady-state error
After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4101 BD initialization error K
After polygon motor K is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4102 BD initialization error C
After polygon motor C is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4103 BD initialization error M
After polygon motor M is driven, ASIC detects a BD error for 1 s Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4104 BD initialization error Y
After polygon motor Y is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB copyir.com
4201 BD steady-state error K
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4202 BD steady-state error C
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4203 BD steady-state error M
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4204 BD steady-state error Y
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB
4300 Polygon motor phase error
ASIC won’t settle in completion of phase adjustment for 2 seconds after a BD signal is detected copyir.com Defective laser scanner unit copyir.com
Defective engine PWB copyir.com
4600 LSU cleaning motor error
After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective LSU cleaning motor copyir.com
Defective engine PWB copyir.com
5101 Main high-voltage error K
Abnormality of charger roller K is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5102 Main high-voltage error C
Abnormality of charger roller C is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5103 Main high-voltage error M
Abnormality of charger roller M is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5104 Main high-voltage error Y
Abnormality of charger roller Y is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 1 detects a temperature higher than 190°C/374°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB copyir.com
6130 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature lower than 30°C/ 86°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 250°C/482°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 2 copyir.com
Defective engine PWB copyir.com
6230 Broken fuser thermistor 2 wire
Input from fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 2 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 2 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6320 Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 3 copyir.com
Defective engine PWB copyir.com
6330 Broken fuser thermistor 3 wire
Input from fuser thermistor 3 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 3 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6520 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 240C/464F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB
6530 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 second copyir.com (Engine CPU) Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB copyir.com
6610 Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser release motor copyir.com
Defective engine PWB copyir.com
6620 IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective IH core motor copyir.com
Defective front PWB copyir.com
Defective engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6720 Fuser IH belt rotation error
A belt rotating pulse is not received for 1 second copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB
6730 Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6750 Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6760 Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6770 Fuser IH low electric power error
The preset power is less than 0 copyir.com6 times of it for 120 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6780 Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6900 Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser front fan motor copyir.com
Defective engine PWB
6910 Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser rear fan motor copyir.com
Defective engine PWB copyir.com
6920 Fuser edge fan motor 1 error
When the fuser edge fan motor 1 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 1 copyir.com
Defective engine PWB copyir.com
6930 Fuser edge fan motor 2 error
When the fuser edge fan motor 2 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 2 copyir.com
Defective engine PWB copyir.com
6940 IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH fan motor copyir.com
Defective engine PWB copyir.com
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6960 Current PWB error
Less than 1A is continuously observed for 5 seconds copyir.com Defective current PWB copyir.com
6990 Fuser power supply incompatibility
Information won’t match between the engine backup and the fuser IH PWB copyir.com Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
7001 Toner motor K error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor K is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor K copyir.com
Defective toner motor K copyir.com
Defective engine PWB copyir.com
7002 Toner motor C error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor C is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor C copyir.com
Defective toner motor C copyir.com
Defective engine PWB copyir.com
7003 Toner motor M error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor M is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor M copyir.com
Defective toner motor M copyir.com
Defective engine PWB copyir.com
7004 Toner motor Y error A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor Y is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor Y copyir.com
Defective toner motor Y copyir.com
Defective engine PWB copyir.com
7101 Toner sensor K error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7102 Toner sensor C error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7103 Toner sensor M error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7104 Toner sensor Y error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7210 Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7221 Broken LSU thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7222 Broken LSU thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C copyir.com
Defective engine PWB copyir.com
7223 Broken LSU thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7224 Broken LSU thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7231 Short-circuited LSU thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7232 Short-circuited LSU thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C
Defective engine PWB copyir.com
7233 Short-circuited LSU thermistor M The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7234 Short-circuited LSU thermistor Y
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7241 Broken developer thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB copyir.com
7242 Broken developer thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7243 Broken developer thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor M copyir.com
Defective engine PWB copyir.com
7244 Broken developer thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7251 Short-circuited developer thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB
7252 Short-circuited developer thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7253 Short-circuited developer thermistor M
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor M copyir.com
Defective engine PWB
7254 Short-circuited developer thermistor Y wire
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7301 Toner hopper motor K error
When the toner hopper motor K is driven, toner hopper sensor K does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor K copyir.com
Defective toner hopper motor K copyir.com
Defective engine PWB copyir.com
7302 Toner hopper motor C error
When the toner hopper motor C is driven, toner hopper sensor C does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor C copyir.com
Defective toner hopper motor C copyir.com
Defective engine PWB copyir.com
7303 Toner hopper motor M error
When the toner hopper motor M is driven, toner hopper sensor M does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor M copyir.com
Defective toner hopper motor M copyir.com
Defective engine PWB copyir.com
7304 Toner hopper motor Y error
When the toner hopper motor Y is driven, toner hopper sensor Y does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor Y copyir.com
Defective toner hopper motor Y copyir.com
Defective engine PWB copyir.com
7401 Developer unit K type mismatch error
Absence of the developer unit K is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7402 Developer unit C type mismatch error
Absence of the developer unit C is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7403 Developer unit M type mismatch error
Absence of the developer unit M is detected copyir.com Defective connector cable or poor contact in the connector
Different type of the developer unit is installed
7404 Developer unit Y type mismatch error
Absence of the developer unit Y is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com
Defective connector cable or poor contact in the connector copyir.com
7601 ID sensor 1 error
An abnormal value is detected in the input data to ID sensor 1 copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7602 ID sensor 2 error
An abnormal value is detected in the input data to ID sensor 2 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7800 Broken outer temperature sensor 1 wire
The sensor input sampling is greater than 255 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7810 Short-circuited outer temperature sensor 1
The sensor input sampling is less than 0 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB K copyir.com
7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB C copyir.com
7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB M copyir.com
7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB Y copyir.com
7911 Developer unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit K copyir.com
7912 Developer unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit C copyir.com
7913 Developer unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit M copyir.com
7914 Developer unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit Y copyir.com
7941 Laser scanner unit K EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB K copyir.com
7942 Laser scanner unit C EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB C copyir.com
7943 Laser scanner unit M EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB M copyir.com
7944 Laser scanner unit Y EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB Y copyir.com
8000 Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible copyir.com The finisher is installed with a device to which it is incompatible copyir.com
8010 Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch home position sensor copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8020 Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8030 Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF paddle sensor
Defective DF paddle motor copyir.com
Defective DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF bundle discharge sensor copyir.com
Defective DF eject release motor copyir.com
Defective DF main PWB copyir.com
8110 DF shift motor 1 error
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector
Defective DF shift sensor 1 copyir.com
Defective DF shift motor 1 copyir.com
Defective DF main PWB copyir.com
8120 DF shift motor 2 error
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 2 copyir.com
Defective DF shift motor 2 copyir.com
Defective DF main PWB copyir.com
8130 DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift release sensor copyir.com
Defective DF shift release motor copyir.com
Defective DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray sensor 3 copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF slide motor copyir.com
Defective DF main PWB copyir.com
8230 DF staple motor error 1
JAM7000 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8240 DF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8250 DF tray motor error 4
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8300 Center-folding unit communication error
Communication with the center-folding unit is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF set sensor copyir.com
Defective PWB copyir.com
8310 CF side registration motor 2 error
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 2 copyir.com
Defective CF side registration motor 2 copyir.com
Defective CF main PWB copyir.com
8320 CF adjustment motor error
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF adjustment sensor 1, 2 copyir.com
Defective CF adjustment motor 1, 2 copyir.com
Defective CF main PWB copyir.com
8330 CF blade motor error
When initial operation, CF blade sensor does not turn on within 1 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF blade sensor copyir.com
Defective CF blade motor copyir.com
Defective CF main PWB copyir.com
8340 CF staple motor error 1
JAM7600 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple sensor copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8350 CF side registration motor 1 error
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 1 copyir.com
Defective CF side registration motor 1 copyir.com
Defective CF main PWB copyir.com
8360 CF main motor error
During driving the motor, lock signal is detected for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF main motor
Defective CF main PWB copyir.com
8370 CF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective slide sensor copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8500 Mailbox communication error
Communication with the mailbox is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8510 MB conveying motor error 1
When initial operation, MB home position sensor does not turn on within 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8520 MB conveying motor error 2
When standby operation, MB home position sensor does not turn off within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8800 Document finisher communication error
Communication with the document finisher is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Improper installation EEPROM copyir.com
Defective DF main PWB copyir.com
8930 Center-folding unit backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM
Defective CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com Defective connector cable or poor contact in the connector
Defective PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Data setup failure copyir.com
Defective coin vender control PWB copyir.com
Defective PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector
Defective DP lift sensor 1 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 2 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DPSHD PWB copyir.com
9080 LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Defective coin vender control PWB copyir.com
9110 Coin vender error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector installed incorrectly copyir.com
Defective rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Defective pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Change jam at the pay-out copyir.com
Defective pay-out motor copyir.com
Defective pay-out sensor copyir.com
9200 DP multi feed sensor communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
9210 DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9220 DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9500, 9510, 9520, 9530, 9540, 9550 Contact the Service Administrative Division copyir.com
F000 Communication error between main PWB and operation PWB Defective main PWB copyir.com
Defective operation PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F040 Communication error between main PWB and print engine Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Communication error between main PWB and scanner engine Defective main PWB copyir.com
Defective ISC PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective ISC PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
کیو سرا میتا Kyocera-Mita TASKalfa 750c
نوشته شده توسط ایراندوست بهزادC021 Developer unit motor-YMC locking error: The developer unit motor-YMC is not rotating normally copyir.com
C022 Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally
C023 Developer unit motor-K locking error: The developer unit motor-K is not rotating normally copyir.com
C024 Developer unit mixer motor-K locking error: The developer unit mixer motor-K is not rotating normally copyir.com
C130 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 1st drawer)
C140 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 2nd drawer)
C150 3rd drawer tray abnormality: The 3rd drawer tray-up motor is not rotating or the 3rd drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 3rd drawer)
C160 4th drawer tray abnormality: The 4th drawer tray-up motor is not rotating or the 4th drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 4th drawer)
C180 LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF)
C1A0 LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF)
C1C0 Option LCF tray-up motor abnormality: The option LCF tray-up motor is not moving normally
C260 Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON copyir.com
C270 (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time copyir.com (2) Downloading firmware with an incorrect model copyir.com
C280 Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time copyir.com
C360 Needle electrode cleaner operation abnormality
C370 Transfer belt operation abnormality
C380 Auto-toner sensor-K abnormality (upper limit)
C381 Auto-toner sensor-K abnormality (lower limit)
C382 Auto-toner sensor-K connection error
C390 Auto-toner sensor-C abnormality (upper limit)
C391 Auto-toner sensor-C abnormality (lower limit)
C392 Auto-toner sensor-C connection error
C3A0 Auto-toner sensor-M abnormality (upper limit)
C3A1 Auto-toner sensor-M abnormality (lower limit)
C3A2 Auto-toner sensor-M connection error
C3B0 Auto-toner sensor-Y abnormality (upper limit)
C3B1 Auto-toner sensor-Y abnormality (lower limit)
C3B2 Auto-toner sensor-Y connection error
C3C0 Process unit connection error
C411 Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON copyir.com
C412 Thermistor/heater lamp abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser belt temperature does not rise within a specified period of time after power-ON copyir.com
C443 Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)
C445 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C446 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C447 Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)
C448 Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified
C451 Thermopile and edge thermistor temperature difference
C452 Thermopile temperature difference
C461 Pressure roller heater 40°C detection (Not determined)
C462 Pressure roller heater 40°C detection (Determined)
C463 Pressure roller thermistor and edge thermistor temperature difference
C464 Pressure roller thermistor temperature difference
C465 Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C466 Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C467 Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status)
C468 Pressure roller thermistor abnormality after entering ready status (overheating)
C471 IH board initialization abnormality
C472 Power supply abnormality
C473 Surge pressure detection / power and voltage upper limit abnormality
C474 Power and voltage lower limit abnormality
C476 IH low power supply
C480 IGBT high temperature abnormality
C481 IH drive circuit abnormality
C490 IH circuit abnormality / IH coil abnormality
C4B0 Fuser unit counter abnormality
C4B1 Fuser unit voltage judgment abnormality
C4D0 Fuser belt thermopile abnormality
C4E0 Fuser unit releasing operation abnormality - Though the pressure roller is released, its position cannot be detected copyir.com
C4E1 Fuser unit contacting operation abnormality - Though the pressure roller is contacted, its position cannot be detected copyir.com
C4E2 Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates copyir.com
C4E3 Fuser motor rotation abnormality
C550 RADF I/F error: Communication error has occurred between the RADF and the scanner copyir.com
C560 Communication error between Engine-CPU and PFC board
C570 Communication error between Engine-CPU and CNV board
C580 Communication error between CNV board and finisher
C5A0 SRAM board not connected (LGC board)
C5A1 SRAM board data abnormality (LGC board)
C730 RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed copyir.com
C880 RADF original feed motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C890 RADF read motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8A0 RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8B0 RADF original exit motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8C0 RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully copyir.com
C8E0 RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred copyir.com
C900 Connection error between SYS board and LGC board
C940 Engine-CPU abnormality
C962 LGC board ID abnormality
C970 High-voltage transformer abnormality: Leakage of the main charger is detected copyir.com
C9E0 Connection error between SLG board and SYS board
CA00 Image position alignment abnormality
CA10 Polygonal motor abnormality: The polygonal motor is not rotating normally
CA20 H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams copyir.com
CA47 SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking copyir.com
CB00 Finisher not connected: Communication error has occurred between the equipment and finisher copyir.com [MJ1103/1104]
CB01 Finisher communication error: Communication error has occurred between the equipment and finisher copyir.com [MJ-1103/1104]
CB10 Entrance motor abnormality: The entrance motor is not rotating normally copyir.com [MJ-1103/1104]
CB11 Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally copyir.com [MJ-1103/1104]
CB12 Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally copyir.com [MJ-1103/1104]
CB13 Finisher exit motor abnormality
CB14 Paper holding arm motor abnormality
CB30 Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally copyir.com [MJ-1103/1104]
CB31 Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly copyir.com [MJ-1103/1104]
CB40 Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally copyir.com [MJ-1103/ 1104]
CB50 Stapler home position error: The stapler home position sensor does not work copyir.com [MJ-1103/1104]
CB51 Stapler shift home position error: The stapler is not at the home position copyir.com [MJ-1103/1104]
CB60 Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally copyir.com [MJ-1103/1104]
CB80 Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON
CB81 Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON copyir.com [MJ-1103/1104]
CB82 Finisher - Main CPU program error
CB83 Saddle Stitch Finisher - Main CPU program error
CB84 Hole Punch Unit - Main CPU program error
CB91 Saddle Stitch Finisher flash ROM abnormality
CB92 Saddle Stitch Finisher RAM abnormality
CB93 Additional folding motor abnormality
CB94 Saddle transport motor abnormality
CB95 Stacker motor abnormality
CBA0 Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally copyir.com [MJ-1103/1104]
CBB0 Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally copyir.com [MJ-1103/1104]
CBC0 Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1103/1104]
CBE0 Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally copyir.com [MJ-1103/1104]
CC20 Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104]
CC30 Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally copyir.com [MJ-1103/1104]
CC31 Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally copyir.com [MJ-1103/1104]
CC41 Paper holder cam home position abnormality: The paper holder cam is not at the home position copyir.com [MJ1103/1104]
CC51 Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC52 Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC60 Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally copyir.com [MJ1103/1104 (when MJ-6102 is installed)]
CC61 Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC71 Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC72 Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC73 Punching device power supply abnormality
CC74 Punch unit transport pulse abnormality
CC80 Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally copyir.com [MJ-1103/1104]
CD60 Sub-hopper toner sensors abnormality copyir.com
CD61 Sub-hopper toner motor-Y abnormality copyir.com
CD62 Sub-hopper toner motor-M abnormality copyir.com
CD63 Sub-hopper toner motor-C abnormality copyir.com
CD64 Sub-hopper toner motor-K abnormality copyir.com
CD71 Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate copyir.com
CD80 TRU waste toner motor locking error: The auger (TRU side) in the TRU waste toner transport path does not rotate copyir.com
CD81 TRU waste toner transport motor locking error: The auger (waste toner box side) in the TRU waste toner transport path does not rotate copyir.com
CD82 TRU waste toner full-status error
CDE0 Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally copyir.com [MJ1103/1104]
CE00 Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ-1103/1104 (when MJ-6102 is installed)]
CE10 Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF copyir.com
CE20 Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed copyir.com
CE40 Image quality control test pattern abnormality: The test pattern is not formed normally copyir.com
CE41 Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally copyir.com
CE42 Image quality TRC control test pattern abnormality (EFI printer board): Image quality TRC control test pattern is not printed normally copyir.com
CE50 Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range copyir.com
CE60 Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range copyir.com
CE71 Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time copyir.com
CE90 Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range copyir.com
CEC0 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally copyir.com
CF10 Communication module SRAM reading failure copyir.com
CF90 Laser optical unit shutter abnormality copyir.com
CFA0 Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal copyir.com
CFA1 Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal copyir.com
E010 Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor copyir.com
E011 Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor copyir.com
E020 Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor copyir.com
E030 Power-ON jam: The paper is remaining on the paper transport path when power is turned ON copyir.com
E061 Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment copyir.com
E062 Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment copyir.com
E063 Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment copyir.com
E064 Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment copyir.com
E065 Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment copyir.com
E071 1st drawer media type mis-setting jam: The media type setting of the 1st drawer is incorrect copyir.com
E072 2nd drawer media type mis-setting jam: The media type setting of the 2nd drawer is incorrect copyir.com
E073 3rd drawer media type mis-setting jam: The media type setting of the 3rd drawer is incorrect copyir.com
E074 4th drawer media type mis-setting jam: The media type setting of the 4th drawer is incorrect copyir.com
E075 Option LCF media type mis-setting jam: The media type setting of the option LCF is incorrect copyir.com
E076 Tandem LCF media type mis-setting jam: The media type setting of the tandem LCF is incorrect copyir.com
E090 Image data delay jam: Image data to be printed cannot be prepared copyir.com
E091 Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware copyir.com
E0A0 Image transport ready time-out jam: Image data to be printed cannot be sent copyir.com
E110 ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing copyir.com
E120 Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor copyir.com
E130 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor copyir.com
E140 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor copyir.com
E150 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
E160 4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor copyir.com
E180 Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor copyir.com
E190 LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor copyir.com
E200 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E210 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E220 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E230 1st drawer misfeeding (Paper not reaching the 1st drawer transport sensor): Paper fed from the 1st drawer does not reach the 1st drawer transport sensor copyir.com
E240 2nd drawer misfeeding (Paper not reaching the 2nd drawer transport sensor): Paper fed from the 2nd drawer does not reach the 2nd drawer transport sensor copyir.com
E260 Option LCF transport jam (Paper not reaching the registration sensor)
E270 Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor copyir.com
E290 Option LCF transport jam: Paper fed from the Option LCF does not reach the 1st drawer transport sensor copyir.com
E2B0 Stop jam at the registration sensor (1st drawer)
E2B1 Stop jam at the registration sensor (2nd drawer)
E2B2 Stop jam at the registration sensor (3rd drawer)
E2B3 Stop jam at the registration sensor (4th drawer)
E2B4 Stop jam at the registration sensor (Bypass tray)
E2B5 Stop jam at the registration sensor (LCF)
E2B6 Stop jam at the registration sensor (ADU)
E2B7 Stop jam at the registration sensor (option LCF)
E300 3rd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E310 3rd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E320 3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir.com
E330 4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E340 4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E350 4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir.com
E360 4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor copyir.com
E370 3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor copyir.com
E380 4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor copyir.com
E3C0 LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor copyir.com
E3D0 LCF transport jam (Paper not reaching the 1st drawer feed sensor): Paper fed from the LCF and passed through the 2nd drawer feed sensor does not reach the 1st drawer feed sensor copyir.com
E3E0 LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor copyir.com
E3F0 Tandem LCF misfeeding (Paper not reaching the tandem LCF feed sensor): Paper fed from the Tandem LCF does not reach the tandem LCF transport sensor copyir.com
E400 Duplexing unit open jam
E430 ADU open jam: The ADU has opened during printing copyir.com
E440 Paper feed cover open jam: The paper feed cover has opened during printing copyir.com
E450 LCF side cover open jam: The LCF side cover has opened during printing copyir.com
E480 Bridge unit open jam: The bridge unit has opened during printing copyir.com
E4A0 Waste toner cover open jam (printing)
E4B0 Bridge unit open jam (printing): The bridge unit has opened during printing copyir.com
E510 Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section copyir.com
E511 ADU misfeeding (Paper not reaching the ADU transport sensor-1)
E540 ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor copyir.com
E550 Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding) copyir.com
E570 Jam not reaching the bridge unit copyir.com
E580 Stop jam at the bridge unit
E590 Jam not reaching the upper paper exit sensor
E5A0 Stop jam at the upper paper exit sensor
E712 Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor copyir.com
E714 Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray copyir.com
E721 Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side) copyir.com
E722 Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section copyir.com
E724 Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor copyir.com
E725 Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor copyir.com
E726 Transport/exit signal reception jam during ADF standby status
E727 Jam not reaching the original reading end sensor
E729 Stop jam at the original reading end sensor
E731 Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor copyir.com
E744 Stop jam at the exit/reverse sensor
E745 Jam not reaching the exit reverse sensor
E746 Exit/reverse sensor paper remaining jam
E762 Registration sensor paper remaining jam
E770 Original width detection sensor-1 paper remaining jam
E771 Original width detection sensor-2 paper remaining jam
E772 Original width detection sensor-3 paper remaining jam
E773 Intermediate transport sensor paper remaining jam
E774 Reading start sensor paper remaining jam
E775 Reading end sensor paper remaining jam
E777 Exit sensor paper remaining jam
E860 Original jam access cover open: The Original jam access cover has opened during RADF operation copyir.com
E870 RADF open jam: RADF has opened during RADF operation copyir.com
E871 Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment copyir.com
E910 Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor copyir.com
E920 Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor copyir.com
E930 Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1 copyir.com
E940 Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2 copyir.com
E970 Jam not reaching the lower paper exit sensor: Paper transported from the bridge unit does not reach the lower paper exit sensor copyir.com
E980 Stop jam at the lower paper exit sensor: Paper transported from the bridge unit does not pass the lower paper exit sensor copyir.com
E9F0 Punching jam: Punching is not performed properly copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
EA10 Paper transport delay jam: The paper which has passed the relay transport path does not reach the inlet sensor copyir.com [MJ-1103/1104]
EA20 Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir.com [MJ1103/1104]
EA21 Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec copyir.com [MJ-1103/1104]
EA22 Paper transport jam (Finisher paper punching edge detection sensor): [MJ-1103/1104]
EA23 Paper transport jam (exit sensor): [MJ-1103/1104]
EA24 Paper transport jam (between entrance and exit sensors): [MJ-1103/1104]
EA25 Paper transport jam (after paper stack exit): [MJ1103/1104]
EA26 Paper transport jam (stop command request): [MJ1103/1104]
EA27 Paper transport jam (paper not inserted): [MJ-1103/ 1104]
EA28 Paper transport jam (assisting arm operation delay): [MJ-1103/1104]
EA29 Paper transport jam (stack transport delay): [MJ1103/1104]
EA31 Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir.com [MJ-1103/1104]
EA32 Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON copyir.com [MJ-1103/1104]
EA40 Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing copyir.com [MJ-1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport copyir.com [MJ-1103/1104]
EA50 Stapling jam: Stapling is not performed properly copyir.com [MJ-1103/1104]
EA60 Early arrival jam: The inlet sensor detects the paper earlier than a specified timing copyir.com [MJ-1103/1104]
EA70 Stack exit belt home position error: The stack exit belt is not at the home position copyir.com [MJ-1103/1104]
EA90 Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104] copyir.com
EAA0 Power-ON jam: Paper exists at No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON copyir.com [MJ-1103/1104]
EAB0 Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor or delivery sensor copyir.com [MJ-1103/1104]
EAB1 Short paper jam (Saddle Stitch Finisher)
EAD0 Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing copyir.com
EAE0 Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher copyir.com
EB30 Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing copyir.com
EB50 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper copyir.com
EB60 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]) copyir.com
ED10 Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
ED11 Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position copyir.com [MJ-1103/1104 (when MJ6102 is installed)]
ED12 Shutter home position error: The shutter is not at the home position copyir.com [MJ-1103/1104]
ED13 Front alignment plate home position error: The front alignment plate is not at the home position copyir.com [MJ1103/1104]
ED14 Rear alignment plate home position error: The rear alignment plate is not at the home position copyir.com [MJ1103/1104]
ED15 Paddle home position error: The paddle is not at the home position copyir.com [MJ-1103/1104]
ED16 Buffer tray home position error: The buffer tray is not at the home position copyir.com [MJ-1103/1104]
EF10 Paper not supported for Saddle Stitch Finisher
EF11 Saddle Stitch Finisher stapling error (front)
EF12 Saddle Stitch Finisher stapling error (rear)
EF13 Saddle paper holder home position detection abnormality
EF14 Saddle paper exit jam
EF15 Saddle Stitch Finisher side alignment motor home position detection abnormality
EF16 Saddle Stitch Finisher stacker motor home position detection abnormality
EF17 Saddle Stitch Finisher folding blade home position detection abnormality
EF18 Saddle Stitch Finisher additional folding roller home position detection abnormality
EF19 Saddle paper folding jam
EF20 Saddle stacker jam
EF21 Hole Punch Unit paper leading edge skew detection abnormality
EF22 Hole Punch Unit paper leading edge detection abnormality
EF23 Hole Punch Unit paper alignment abnormality
EF24 Hole Punch Unit paper trailing edge skew detection abnormality
EF25 Hole Punch Unit paper trailing edge detection abnormality
EF27 Hole Punch Unit paper edge detection order abnormality-1
EF28 Hole Punch Unit paper edge detection order abnormality-2
F070 Communication error between System-CPU and Engine-CPU
F090 SRAM abnormality on the SYS board
F100 HDD format error: HDD cannot be initialized normally copyir.com
F101 HDD unmounted: Connection of HDD cannot be detected copyir.com
F102 HDD start error: HDD cannot become ‘Ready’ state
F103 HDD transfer time-out: Reading/writing cannot be performed in the specified period of time copyir.com
F104 HDD data error: Abnormality is detected in the data of HDD copyir.com
F105 HDD other error
F106 Point and Print partition damage
F107 /BOX partition damage
F108 /SHA partition damage
F110 Communication error between System-CPU and Scanner-CPU
F111 Scanner response abnormality
F120 Database abnormality: Database is not operating normally copyir.com
F130 Invalid MAC address
F200 Data Overwrite option (GP-1070) disabled
F350 SLG board abnormality
F400 SYS board cooling fan abnormality
کیو سرا میتا Kyocera-Mita TASKalfa 6550ci
نوشته شده توسط ایراندوست بهزاد0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory copyir.com
Defective engine PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Improper installation EEPROM copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error
(engine PWB) Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0620 FAX image DIMM error
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com
Defective main PWB copyir.com
0650 FAX image DIMM check error
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB copyir.com
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0900 FAX software incompatible detection error
Incompatible FAX control PWB is installed copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0970 12 V power down detect
Power is disconnected during sleeping copyir.com Defective power source PWB copyir.com
0980 24 V power down detect
24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected copyir.com Defective power source PWB copyir.com
1000 MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 1 copyir.com5 s copyir.com Defective MP plate elevation mechanism copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective MP lift motor copyir.com
Defective engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective lift motor 1 copyir.com
Defective engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 2 copyir.com
Defective engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1050 SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM lift motor copyir.com
Defective SM main PWB copyir.com
1060 PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1070 PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 2 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD lift motor copyir.com
Defective SD main PWB copyir.com
1250 SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
The SM multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1400 BR guide motor error
The BR decurler sensor won’t turn on three times in a row after the home position of the rotary guide has been detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR guide motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1410 BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR decurler motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1710 Side multi tray incompatible detection error
The side multi tray has been installed with a device to which it is incompatible copyir.com The side multi tray is installed with a device to which it is incompatible copyir.com
1720 Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible copyir.com The paper feeder is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1810 Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1820 Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1910 Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective SM main PWB copyir.com
Device damage of EEPROM copyir.com
1920 Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1950 Transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com
2101 Developer motor K error
After developer motor K is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor K copyir.com
Defective engine PWB copyir.com
2102 Developer motor C error
After developer motor C is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor C copyir.com
Defective engine PWB copyir.com
2103 Developer motor M error
After developer motor M is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor M is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor M copyir.com
Defective engine PWB copyir.com
2104 Developer motor Y error
After developer motor Y is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor Y is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor Y copyir.com
Defective engine PWB
2201 Drum motor K steady-state error
After drum motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2202 Drum motor C steady-state error
Drum motor C does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2203 Drum motor M steady-state error
Drum motor M does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2204 Drum motor Y steady-state error
Drum motor Y does not keep the steadystate speed for 5 s successively since the motor is stabilized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2212 Drum motor C startup error
Drum motor C is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2213 Drum motor M startup error
Drum motor M is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2214 Drum motor Y startup error
Drum motor Y is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2231 Drum motor K main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB
2232 Drum motor C main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2233 Drum motor M main sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2234 Drum motor Y main sensor error No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB copyir.com
2241 Drum motor K sub sensor error
No signal is input to the sensor for 100 ms continuously Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor K copyir.com
Defective engine PWB copyir.com
2242 Drum motor C sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor C copyir.com
Defective engine PWB copyir.com
2243 Drum motor M sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor M copyir.com
Defective engine PWB copyir.com
2244 Drum motor Y sub sensor error
No signal is input to the sensor for 100 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor Y copyir.com
Defective engine PWB
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2550 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
2600 PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor
Defective PF main PWB copyir.com
2640 SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD paper feed motor
Defective SD main PWB copyir.com
2650 SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM paper feed motor copyir.com
Defective SM main PWB copyir.com
2660 PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2670 PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2700 Color release motor error
When the color release motor is driven, the color release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective color release motor copyir.com
Defective engine PWB copyir.com
2730 Transfer release motor error
When the transfer release motor is driven, the transfer release sensor does not turn on/off for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer release motor copyir.com
Defective engine PWB copyir.com
2760 Transfer motor startup error
Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2770 Transfer skew error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2780 Transfer skew sensor error
An abnormal value is detected to transfer skew sensor copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer skew sensor copyir.com
Defective engine PWB copyir.com
2790 Transfer skew motor error
When the transfer skew motor is driven, timeouts were detected twice in a row copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer skew motor copyir.com
Defective engine PWB copyir.com
2810 Waste toner motor error
Initialized when an error is constantly observed for 2 seconds after the waste toner motor is activated copyir.com An error is constantly observed for 2 copyir.com5 seconds after rebooting copyir.com Defective connector cable or poor contact in the connector
Defective drive transmission system of motor copyir.com
Defective waste toner motor copyir.com
Defective engine PWB copyir.com
2820 Transfer motor steady-state error Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer motor copyir.com
Defective engine PWB copyir.com
2840 Transfer cleaning motor error
After transfer cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com
After transfer cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective transfer cleaning motor copyir.com
Defective engine PWB copyir.com
2850 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2860 Transfer belt sensor error
The signal is not received for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective transfer belt sensor copyir.com
Defective engine PWB copyir.com
2950 Motor control PWB communication error
A communication error from the motor control PWB is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective motor control PWB copyir.com
Defective engine PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective scanner motor copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LED lamp PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3300 Optical system (AGC) error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp copyir.com
Defective CCD PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3310 CIS AGC error
After AGC, correct input is not obtained at CIS copyir.com Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3500 Communication error between scanner and ASIC An error code is detected copyir.com Defective connector cable or poor contact in the connector
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective ISC PWB copyir.com
3700 Scanner device error CCD connector inserted incorrectly copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective ISC PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Defective backup memory or PWB copyir.com
4001 Polygon motor K synchronization error
After polygon motor K is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4002 Polygon motor C synchronization error
After polygon motor C is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4003 Polygon motor M synchronization error
After polygon motor M is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4004 Polygon motor Y synchronization error
After polygon motor Y is driven, the ready signal does not turn to L within 30 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4011 Polygon motor K steady-state error
After polygon motor K is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor K copyir.com
Defective engine PWB copyir.com
4012 Polygon motor C steady-state error
After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor C copyir.com
Defective engine PWB copyir.com
4013 Polygon motor M steady-state error
After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector
Defective polygon motor M copyir.com
Defective engine PWB copyir.com
4014 Polygon motor Y steady-state error
After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor Y copyir.com
Defective engine PWB copyir.com
4101 BD initialization error K
After polygon motor K is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4102 BD initialization error C
After polygon motor C is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4103 BD initialization error M
After polygon motor M is driven, ASIC detects a BD error for 1 s Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4104 BD initialization error Y
After polygon motor Y is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB copyir.com
4201 BD steady-state error K
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB K copyir.com
Defective engine PWB copyir.com
4202 BD steady-state error C
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB C copyir.com
Defective engine PWB copyir.com
4203 BD steady-state error M
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB M copyir.com
Defective engine PWB copyir.com
4204 BD steady-state error Y
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB Y copyir.com
Defective engine PWB
4300 Polygon motor phase error
ASIC won’t settle in completion of phase adjustment for 2 seconds after a BD signal is detected copyir.com Defective laser scanner unit copyir.com
Defective engine PWB copyir.com
4600 LSU cleaning motor error
After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective LSU cleaning motor copyir.com
Defective engine PWB copyir.com
5101 Main high-voltage error K
Abnormality of charger roller K is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5102 Main high-voltage error C
Abnormality of charger roller C is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5103 Main high-voltage error M
Abnormality of charger roller M is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
5104 Main high-voltage error Y
Abnormality of charger roller Y is detected when Vpp adjustment copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB 1 copyir.com
Defective engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 1 detects a temperature higher than 190°C/374°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB copyir.com
6130 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature lower than 30°C/ 86°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 60 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 250°C/482°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 2 copyir.com
Defective engine PWB copyir.com
6230 Broken fuser thermistor 2 wire
Input from fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 2 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 2 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6320 Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 3 copyir.com
Defective engine PWB copyir.com
6330 Broken fuser thermistor 3 wire
Input from fuser thermistor 3 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 3 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6520 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 240C/464F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB
6530 Broken fuser thermistor 4 wire
Input from fuser thermistor 4 is 992 or more (A/D value) continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 second copyir.com (Engine CPU) Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB copyir.com
6610 Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser release motor copyir.com
Defective engine PWB copyir.com
6620 IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective IH core motor copyir.com
Defective front PWB copyir.com
Defective engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6720 Fuser IH belt rotation error
A belt rotating pulse is not received for 1 second copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB
6730 Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6750 Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6760 Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6770 Fuser IH low electric power error
The preset power is less than 0 copyir.com6 times of it for 120 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB
Defective engine PWB copyir.com
6780 Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6900 Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser front fan motor copyir.com
Defective engine PWB
6910 Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser rear fan motor copyir.com
Defective engine PWB copyir.com
6920 Fuser edge fan motor 1 error
When the fuser edge fan motor 1 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 1 copyir.com
Defective engine PWB copyir.com
6930 Fuser edge fan motor 2 error
When the fuser edge fan motor 2 is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser edge fan motor 2 copyir.com
Defective engine PWB copyir.com
6940 IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH fan motor copyir.com
Defective engine PWB copyir.com
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6960 Current PWB error
Less than 1A is continuously observed for 5 seconds copyir.com Defective current PWB copyir.com
6990 Fuser power supply incompatibility
Information won’t match between the engine backup and the fuser IH PWB copyir.com Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
7001 Toner motor K error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor K is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor K copyir.com
Defective toner motor K copyir.com
Defective engine PWB copyir.com
7002 Toner motor C error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor C is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor C copyir.com
Defective toner motor C copyir.com
Defective engine PWB copyir.com
7003 Toner motor M error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor M is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor M copyir.com
Defective toner motor M copyir.com
Defective engine PWB copyir.com
7004 Toner motor Y error A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor Y is activated copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective screw sensor Y copyir.com
Defective toner motor Y copyir.com
Defective engine PWB copyir.com
7101 Toner sensor K error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7102 Toner sensor C error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7103 Toner sensor M error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7104 Toner sensor Y error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7210 Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 2 copyir.com
Defective engine PWB copyir.com
7221 Broken LSU thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7222 Broken LSU thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C copyir.com
Defective engine PWB copyir.com
7223 Broken LSU thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7224 Broken LSU thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7231 Short-circuited LSU thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor K copyir.com
Defective engine PWB copyir.com
7232 Short-circuited LSU thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor C
Defective engine PWB copyir.com
7233 Short-circuited LSU thermistor M The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor M copyir.com
Defective engine PWB copyir.com
7234 Short-circuited LSU thermistor Y
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor Y copyir.com
Defective engine PWB copyir.com
7241 Broken developer thermistor K wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB copyir.com
7242 Broken developer thermistor C wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7243 Broken developer thermistor M wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor M copyir.com
Defective engine PWB copyir.com
7244 Broken developer thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7251 Short-circuited developer thermistor K
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor K copyir.com
Defective engine PWB
7252 Short-circuited developer thermistor C
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor C copyir.com
Defective engine PWB copyir.com
7253 Short-circuited developer thermistor M
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector
Defective developer thermistor M copyir.com
Defective engine PWB
7254 Short-circuited developer thermistor Y wire
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor Y copyir.com
Defective engine PWB copyir.com
7301 Toner hopper motor K error
When the toner hopper motor K is driven, toner hopper sensor K does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor K copyir.com
Defective toner hopper motor K copyir.com
Defective engine PWB copyir.com
7302 Toner hopper motor C error
When the toner hopper motor C is driven, toner hopper sensor C does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective toner hopper sensor C copyir.com
Defective toner hopper motor C copyir.com
Defective engine PWB copyir.com
7303 Toner hopper motor M error
When the toner hopper motor M is driven, toner hopper sensor M does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor M copyir.com
Defective toner hopper motor M copyir.com
Defective engine PWB copyir.com
7304 Toner hopper motor Y error
When the toner hopper motor Y is driven, toner hopper sensor Y does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor Y copyir.com
Defective toner hopper motor Y copyir.com
Defective engine PWB copyir.com
7401 Developer unit K type mismatch error
Absence of the developer unit K is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7402 Developer unit C type mismatch error
Absence of the developer unit C is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7403 Developer unit M type mismatch error
Absence of the developer unit M is detected copyir.com Defective connector cable or poor contact in the connector
Different type of the developer unit is installed
7404 Developer unit Y type mismatch error
Absence of the developer unit Y is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com
Defective connector cable or poor contact in the connector copyir.com
7601 ID sensor 1 error
An abnormal value is detected in the input data to ID sensor 1 copyir.com Defective connector cable or poor contact in the connector
Defective engine PWB copyir.com
7602 ID sensor 2 error
An abnormal value is detected in the input data to ID sensor 2 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7800 Broken outer temperature sensor 1 wire
The sensor input sampling is greater than 255 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7810 Short-circuited outer temperature sensor 1
The sensor input sampling is less than 0 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor 1 copyir.com
Defective engine PWB copyir.com
7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB K copyir.com
7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB C copyir.com
7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB M copyir.com
7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB Y copyir.com
7911 Developer unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit K copyir.com
7912 Developer unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit C copyir.com
7913 Developer unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit M copyir.com
7914 Developer unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit Y copyir.com
7941 Laser scanner unit K EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB K copyir.com
7942 Laser scanner unit C EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB C copyir.com
7943 Laser scanner unit M EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB M copyir.com
7944 Laser scanner unit Y EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB Y copyir.com
8000 Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible copyir.com The finisher is installed with a device to which it is incompatible copyir.com
8010 Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch home position sensor copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8020 Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8030 Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF paddle sensor
Defective DF paddle motor copyir.com
Defective DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF bundle discharge sensor copyir.com
Defective DF eject release motor copyir.com
Defective DF main PWB copyir.com
8110 DF shift motor 1 error
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector
Defective DF shift sensor 1 copyir.com
Defective DF shift motor 1 copyir.com
Defective DF main PWB copyir.com
8120 DF shift motor 2 error
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 2 copyir.com
Defective DF shift motor 2 copyir.com
Defective DF main PWB copyir.com
8130 DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift release sensor copyir.com
Defective DF shift release motor copyir.com
Defective DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray sensor 3 copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF slide motor copyir.com
Defective DF main PWB copyir.com
8230 DF staple motor error 1
JAM7000 is detected twice copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple sensor copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8240 DF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8250 DF tray motor error 4
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8300 Center-folding unit communication error
Communication with the center-folding unit is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF set sensor copyir.com
Defective PWB copyir.com
8310 CF side registration motor 2 error
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 2 copyir.com
Defective CF side registration motor 2 copyir.com
Defective CF main PWB copyir.com
8320 CF adjustment motor error
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF adjustment sensor 1, 2 copyir.com
Defective CF adjustment motor 1, 2 copyir.com
Defective CF main PWB copyir.com
8330 CF blade motor error
When initial operation, CF blade sensor does not turn on within 1 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF blade sensor copyir.com
Defective CF blade motor copyir.com
Defective CF main PWB copyir.com
8340 CF staple motor error 1
JAM7600 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple sensor copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8350 CF side registration motor 1 error
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 1 copyir.com
Defective CF side registration motor 1 copyir.com
Defective CF main PWB copyir.com
8360 CF main motor error
During driving the motor, lock signal is detected for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF main motor
Defective CF main PWB copyir.com
8370 CF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective slide sensor copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8500 Mailbox communication error
Communication with the mailbox is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8510 MB conveying motor error 1
When initial operation, MB home position sensor does not turn on within 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8520 MB conveying motor error 2
When standby operation, MB home position sensor does not turn off within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8800 Document finisher communication error
Communication with the document finisher is not possible copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Defective PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector (4000-sheet finisher) copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher) copyir.com
Improper installation EEPROM copyir.com
Defective DF main PWB copyir.com
8930 Center-folding unit backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM
Defective CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com Defective connector cable or poor contact in the connector
Defective PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Data setup failure copyir.com
Defective coin vender control PWB copyir.com
Defective PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector
Defective DP lift sensor 1 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 2 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DPSHD PWB copyir.com
9080 LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Defective coin vender control PWB copyir.com
9110 Coin vender error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector installed incorrectly copyir.com
Defective rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Defective pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Change jam at the pay-out copyir.com
Defective pay-out motor copyir.com
Defective pay-out sensor copyir.com
9200 DP multi feed sensor communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
9210 DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9220 DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9500, 9510, 9520, 9530, 9540, 9550 Contact the Service Administrative Division copyir.com
F000 Communication error between main PWB and operation PWB Defective main PWB copyir.com
Defective operation PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F040 Communication error between main PWB and print engine Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Communication error between main PWB and scanner engine Defective main PWB copyir.com
Defective ISC PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective ISC PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
کیو سرا میتا Kyocera-Mita TASKalfa 650c
نوشته شده توسط ایراندوست بهزادC021 Developer unit motor-YMC locking error: The developer unit motor-YMC is not rotating normally copyir.com
C022 Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally
C023 Developer unit motor-K locking error: The developer unit motor-K is not rotating normally copyir.com
C024 Developer unit mixer motor-K locking error: The developer unit mixer motor-K is not rotating normally copyir.com
C130 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 1st drawer)
C140 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 2nd drawer)
C150 3rd drawer tray abnormality: The 3rd drawer tray-up motor is not rotating or the 3rd drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 3rd drawer)
C160 4th drawer tray abnormality: The 4th drawer tray-up motor is not rotating or the 4th drawer tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the 4th drawer)
C180 LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF)
C1A0 LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally copyir.com (the case that paper can be fed from any drawer except the LCF)
C1C0 Option LCF tray-up motor abnormality: The option LCF tray-up motor is not moving normally
C260 Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON copyir.com
C270 (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time copyir.com (2) Downloading firmware with an incorrect model copyir.com
C280 Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time copyir.com
C360 Needle electrode cleaner operation abnormality
C370 Transfer belt operation abnormality
C380 Auto-toner sensor-K abnormality (upper limit)
C381 Auto-toner sensor-K abnormality (lower limit)
C382 Auto-toner sensor-K connection error
C390 Auto-toner sensor-C abnormality (upper limit)
C391 Auto-toner sensor-C abnormality (lower limit)
C392 Auto-toner sensor-C connection error
C3A0 Auto-toner sensor-M abnormality (upper limit)
C3A1 Auto-toner sensor-M abnormality (lower limit)
C3A2 Auto-toner sensor-M connection error
C3B0 Auto-toner sensor-Y abnormality (upper limit)
C3B1 Auto-toner sensor-Y abnormality (lower limit)
C3B2 Auto-toner sensor-Y connection error
C3C0 Process unit connection error
C411 Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON copyir.com
C412 Thermistor/heater lamp abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser belt temperature does not rise within a specified period of time after power-ON copyir.com
C443 Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)
C445 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C446 Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)
C447 Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)
C448 Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified
C451 Thermopile and edge thermistor temperature difference
C452 Thermopile temperature difference
C461 Pressure roller heater 40°C detection (Not determined)
C462 Pressure roller heater 40°C detection (Determined)
C463 Pressure roller thermistor and edge thermistor temperature difference
C464 Pressure roller thermistor temperature difference
C465 Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C466 Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)
C467 Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status)
C468 Pressure roller thermistor abnormality after entering ready status (overheating)
C471 IH board initialization abnormality
C472 Power supply abnormality
C473 Surge pressure detection / power and voltage upper limit abnormality
C474 Power and voltage lower limit abnormality
C476 IH low power supply
C480 IGBT high temperature abnormality
C481 IH drive circuit abnormality
C490 IH circuit abnormality / IH coil abnormality
C4B0 Fuser unit counter abnormality
C4B1 Fuser unit voltage judgment abnormality
C4D0 Fuser belt thermopile abnormality
C4E0 Fuser unit releasing operation abnormality - Though the pressure roller is released, its position cannot be detected copyir.com
C4E1 Fuser unit contacting operation abnormality - Though the pressure roller is contacted, its position cannot be detected copyir.com
C4E2 Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates copyir.com
C4E3 Fuser motor rotation abnormality
C550 RADF I/F error: Communication error has occurred between the RADF and the scanner copyir.com
C560 Communication error between Engine-CPU and PFC board
C570 Communication error between Engine-CPU and CNV board
C580 Communication error between CNV board and finisher
C5A0 SRAM board not connected (LGC board)
C5A1 SRAM board data abnormality (LGC board)
C730 RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed copyir.com
C880 RADF original feed motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C890 RADF read motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8A0 RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8B0 RADF original exit motor abnormality: An error signal has been detected when the motor is rotating copyir.com
C8C0 RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully copyir.com
C8E0 RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred copyir.com
C900 Connection error between SYS board and LGC board
C940 Engine-CPU abnormality
C962 LGC board ID abnormality
C970 High-voltage transformer abnormality: Leakage of the main charger is detected copyir.com
C9E0 Connection error between SLG board and SYS board
CA00 Image position alignment abnormality
CA10 Polygonal motor abnormality: The polygonal motor is not rotating normally
CA20 H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams copyir.com
CA47 SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking copyir.com
CB00 Finisher not connected: Communication error has occurred between the equipment and finisher copyir.com [MJ1103/1104]
CB01 Finisher communication error: Communication error has occurred between the equipment and finisher copyir.com [MJ-1103/1104]
CB10 Entrance motor abnormality: The entrance motor is not rotating normally copyir.com [MJ-1103/1104]
CB11 Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally copyir.com [MJ-1103/1104]
CB12 Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally copyir.com [MJ-1103/1104]
CB13 Finisher exit motor abnormality
CB14 Paper holding arm motor abnormality
CB30 Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally copyir.com [MJ-1103/1104]
CB31 Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly copyir.com [MJ-1103/1104]
CB40 Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally copyir.com [MJ-1103/ 1104]
CB50 Stapler home position error: The stapler home position sensor does not work copyir.com [MJ-1103/1104]
CB51 Stapler shift home position error: The stapler is not at the home position copyir.com [MJ-1103/1104]
CB60 Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally copyir.com [MJ-1103/1104]
CB80 Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON
CB81 Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON copyir.com [MJ-1103/1104]
CB82 Finisher - Main CPU program error
CB83 Saddle Stitch Finisher - Main CPU program error
CB84 Hole Punch Unit - Main CPU program error
CB91 Saddle Stitch Finisher flash ROM abnormality
CB92 Saddle Stitch Finisher RAM abnormality
CB93 Additional folding motor abnormality
CB94 Saddle transport motor abnormality
CB95 Stacker motor abnormality
CBA0 Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally copyir.com [MJ-1103/1104]
CBB0 Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally copyir.com [MJ-1103/1104]
CBC0 Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally copyir.com [MJ-1103/1104]
CBE0 Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally copyir.com [MJ-1103/1104]
CC20 Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104]
CC30 Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally copyir.com [MJ-1103/1104]
CC31 Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally copyir.com [MJ-1103/1104]
CC41 Paper holder cam home position abnormality: The paper holder cam is not at the home position copyir.com [MJ1103/1104]
CC51 Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC52 Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC60 Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally copyir.com [MJ1103/1104 (when MJ-6102 is installed)]
CC61 Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
CC71 Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC72 Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir.com [MJ-1103/ 1104 (when MJ-6102 is installed)]
CC73 Punching device power supply abnormality
CC74 Punch unit transport pulse abnormality
CC80 Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally copyir.com [MJ-1103/1104]
CD60 Sub-hopper toner sensors abnormality copyir.com
CD61 Sub-hopper toner motor-Y abnormality copyir.com
CD62 Sub-hopper toner motor-M abnormality copyir.com
CD63 Sub-hopper toner motor-C abnormality copyir.com
CD64 Sub-hopper toner motor-K abnormality copyir.com
CD71 Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate copyir.com
CD80 TRU waste toner motor locking error: The auger (TRU side) in the TRU waste toner transport path does not rotate copyir.com
CD81 TRU waste toner transport motor locking error: The auger (waste toner box side) in the TRU waste toner transport path does not rotate copyir.com
CD82 TRU waste toner full-status error
CDE0 Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally copyir.com [MJ1103/1104]
CE00 Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ-1103/1104 (when MJ-6102 is installed)]
CE10 Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF copyir.com
CE20 Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed copyir.com
CE40 Image quality control test pattern abnormality: The test pattern is not formed normally copyir.com
CE41 Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally copyir.com
CE42 Image quality TRC control test pattern abnormality (EFI printer board): Image quality TRC control test pattern is not printed normally copyir.com
CE50 Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range copyir.com
CE60 Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range copyir.com
CE71 Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time copyir.com
CE90 Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range copyir.com
CEC0 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally copyir.com
CF10 Communication module SRAM reading failure copyir.com
CF90 Laser optical unit shutter abnormality copyir.com
CFA0 Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal copyir.com
CFA1 Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal copyir.com
E010 Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor copyir.com
E011 Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor copyir.com
E020 Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor copyir.com
E030 Power-ON jam: The paper is remaining on the paper transport path when power is turned ON copyir.com
E061 Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment copyir.com
E062 Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment copyir.com
E063 Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment copyir.com
E064 Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment copyir.com
E065 Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment copyir.com
E071 1st drawer media type mis-setting jam: The media type setting of the 1st drawer is incorrect copyir.com
E072 2nd drawer media type mis-setting jam: The media type setting of the 2nd drawer is incorrect copyir.com
E073 3rd drawer media type mis-setting jam: The media type setting of the 3rd drawer is incorrect copyir.com
E074 4th drawer media type mis-setting jam: The media type setting of the 4th drawer is incorrect copyir.com
E075 Option LCF media type mis-setting jam: The media type setting of the option LCF is incorrect copyir.com
E076 Tandem LCF media type mis-setting jam: The media type setting of the tandem LCF is incorrect copyir.com
E090 Image data delay jam: Image data to be printed cannot be prepared copyir.com
E091 Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware copyir.com
E0A0 Image transport ready time-out jam: Image data to be printed cannot be sent copyir.com
E110 ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing copyir.com
E120 Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor copyir.com
E130 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor copyir.com
E140 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor copyir.com
E150 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
E160 4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor copyir.com
E180 Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor copyir.com
E190 LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor copyir.com
E200 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E210 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E220 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E230 1st drawer misfeeding (Paper not reaching the 1st drawer transport sensor): Paper fed from the 1st drawer does not reach the 1st drawer transport sensor copyir.com
E240 2nd drawer misfeeding (Paper not reaching the 2nd drawer transport sensor): Paper fed from the 2nd drawer does not reach the 2nd drawer transport sensor copyir.com
E260 Option LCF transport jam (Paper not reaching the registration sensor)
E270 Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor copyir.com
E290 Option LCF transport jam: Paper fed from the Option LCF does not reach the 1st drawer transport sensor copyir.com
E2B0 Stop jam at the registration sensor (1st drawer)
E2B1 Stop jam at the registration sensor (2nd drawer)
E2B2 Stop jam at the registration sensor (3rd drawer)
E2B3 Stop jam at the registration sensor (4th drawer)
E2B4 Stop jam at the registration sensor (Bypass tray)
E2B5 Stop jam at the registration sensor (LCF)
E2B6 Stop jam at the registration sensor (ADU)
E2B7 Stop jam at the registration sensor (option LCF)
E300 3rd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E310 3rd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E320 3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir.com
E330 4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir.com
E340 4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir.com
E350 4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir.com
E360 4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor copyir.com
E370 3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor copyir.com
E380 4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor copyir.com
E3C0 LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor copyir.com
E3D0 LCF transport jam (Paper not reaching the 1st drawer feed sensor): Paper fed from the LCF and passed through the 2nd drawer feed sensor does not reach the 1st drawer feed sensor copyir.com
E3E0 LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor copyir.com
E3F0 Tandem LCF misfeeding (Paper not reaching the tandem LCF feed sensor): Paper fed from the Tandem LCF does not reach the tandem LCF transport sensor copyir.com
E400 Duplexing unit open jam
E430 ADU open jam: The ADU has opened during printing copyir.com
E440 Paper feed cover open jam: The paper feed cover has opened during printing copyir.com
E450 LCF side cover open jam: The LCF side cover has opened during printing copyir.com
E480 Bridge unit open jam: The bridge unit has opened during printing copyir.com
E4A0 Waste toner cover open jam (printing)
E4B0 Bridge unit open jam (printing): The bridge unit has opened during printing copyir.com
E510 Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section copyir.com
E511 ADU misfeeding (Paper not reaching the ADU transport sensor-1)
E540 ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor copyir.com
E550 Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding) copyir.com
E570 Jam not reaching the bridge unit copyir.com
E580 Stop jam at the bridge unit
E590 Jam not reaching the upper paper exit sensor
E5A0 Stop jam at the upper paper exit sensor
E712 Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor copyir.com
E714 Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray copyir.com
E721 Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side) copyir.com
E722 Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section copyir.com
E724 Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor copyir.com
E725 Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor copyir.com
E726 Transport/exit signal reception jam during ADF standby status
E727 Jam not reaching the original reading end sensor
E729 Stop jam at the original reading end sensor
E731 Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor copyir.com
E744 Stop jam at the exit/reverse sensor
E745 Jam not reaching the exit reverse sensor
E746 Exit/reverse sensor paper remaining jam
E762 Registration sensor paper remaining jam
E770 Original width detection sensor-1 paper remaining jam
E771 Original width detection sensor-2 paper remaining jam
E772 Original width detection sensor-3 paper remaining jam
E773 Intermediate transport sensor paper remaining jam
E774 Reading start sensor paper remaining jam
E775 Reading end sensor paper remaining jam
E777 Exit sensor paper remaining jam
E860 Original jam access cover open: The Original jam access cover has opened during RADF operation copyir.com
E870 RADF open jam: RADF has opened during RADF operation copyir.com
E871 Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment copyir.com
E910 Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor copyir.com
E920 Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor copyir.com
E930 Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1 copyir.com
E940 Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2 copyir.com
E970 Jam not reaching the lower paper exit sensor: Paper transported from the bridge unit does not reach the lower paper exit sensor copyir.com
E980 Stop jam at the lower paper exit sensor: Paper transported from the bridge unit does not pass the lower paper exit sensor copyir.com
E9F0 Punching jam: Punching is not performed properly copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
EA10 Paper transport delay jam: The paper which has passed the relay transport path does not reach the inlet sensor copyir.com [MJ-1103/1104]
EA20 Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir.com [MJ1103/1104]
EA21 Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec copyir.com [MJ-1103/1104]
EA22 Paper transport jam (Finisher paper punching edge detection sensor): [MJ-1103/1104]
EA23 Paper transport jam (exit sensor): [MJ-1103/1104]
EA24 Paper transport jam (between entrance and exit sensors): [MJ-1103/1104]
EA25 Paper transport jam (after paper stack exit): [MJ1103/1104]
EA26 Paper transport jam (stop command request): [MJ1103/1104]
EA27 Paper transport jam (paper not inserted): [MJ-1103/ 1104]
EA28 Paper transport jam (assisting arm operation delay): [MJ-1103/1104]
EA29 Paper transport jam (stack transport delay): [MJ1103/1104]
EA31 Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir.com [MJ-1103/1104]
EA32 Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON copyir.com [MJ-1103/1104]
EA40 Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing copyir.com [MJ-1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport copyir.com [MJ-1103/1104]
EA50 Stapling jam: Stapling is not performed properly copyir.com [MJ-1103/1104]
EA60 Early arrival jam: The inlet sensor detects the paper earlier than a specified timing copyir.com [MJ-1103/1104]
EA70 Stack exit belt home position error: The stack exit belt is not at the home position copyir.com [MJ-1103/1104]
EA90 Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104] copyir.com
EAA0 Power-ON jam: Paper exists at No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON copyir.com [MJ-1103/1104]
EAB0 Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No copyir.com1 paper sensor, No copyir.com 2 paper sensor, No copyir.com3 paper sensor or delivery sensor copyir.com [MJ-1103/1104]
EAB1 Short paper jam (Saddle Stitch Finisher)
EAD0 Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing copyir.com
EAE0 Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher copyir.com
EB30 Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing copyir.com
EB50 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper copyir.com
EB60 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]) copyir.com
ED10 Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position copyir.com [MJ-1103/1104 (when MJ-6102 is installed)]
ED11 Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position copyir.com [MJ-1103/1104 (when MJ6102 is installed)]
ED12 Shutter home position error: The shutter is not at the home position copyir.com [MJ-1103/1104]
ED13 Front alignment plate home position error: The front alignment plate is not at the home position copyir.com [MJ1103/1104]
ED14 Rear alignment plate home position error: The rear alignment plate is not at the home position copyir.com [MJ1103/1104]
ED15 Paddle home position error: The paddle is not at the home position copyir.com [MJ-1103/1104]
ED16 Buffer tray home position error: The buffer tray is not at the home position copyir.com [MJ-1103/1104]
EF10 Paper not supported for Saddle Stitch Finisher
EF11 Saddle Stitch Finisher stapling error (front)
EF12 Saddle Stitch Finisher stapling error (rear)
EF13 Saddle paper holder home position detection abnormality
EF14 Saddle paper exit jam
EF15 Saddle Stitch Finisher side alignment motor home position detection abnormality
EF16 Saddle Stitch Finisher stacker motor home position detection abnormality
EF17 Saddle Stitch Finisher folding blade home position detection abnormality
EF18 Saddle Stitch Finisher additional folding roller home position detection abnormality
EF19 Saddle paper folding jam
EF20 Saddle stacker jam
EF21 Hole Punch Unit paper leading edge skew detection abnormality
EF22 Hole Punch Unit paper leading edge detection abnormality
EF23 Hole Punch Unit paper alignment abnormality
EF24 Hole Punch Unit paper trailing edge skew detection abnormality
EF25 Hole Punch Unit paper trailing edge detection abnormality
EF27 Hole Punch Unit paper edge detection order abnormality-1
EF28 Hole Punch Unit paper edge detection order abnormality-2
F070 Communication error between System-CPU and Engine-CPU
F090 SRAM abnormality on the SYS board
F100 HDD format error: HDD cannot be initialized normally copyir.com
F101 HDD unmounted: Connection of HDD cannot be detected copyir.com
F102 HDD start error: HDD cannot become ‘Ready’ state
F103 HDD transfer time-out: Reading/writing cannot be performed in the specified period of time copyir.com
F104 HDD data error: Abnormality is detected in the data of HDD copyir.com
F105 HDD other error
F106 Point and Print partition damage
F107 /BOX partition damage
F108 /SHA partition damage
F110 Communication error between System-CPU and Scanner-CPU
F111 Scanner response abnormality
F120 Database abnormality: Database is not operating normally copyir.com
F130 Invalid MAC address
F200 Data Overwrite option (GP-1070) disabled
F350 SLG board abnormality
F400 SYS board cooling fan abnormality
کیو سرا میتا Kyocera-Mita TASKalfa 6500i
نوشته شده توسط ایراندوست بهزاد0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0060 Illegal engine PWB type
The engine main PWB and the engine sub PWB are incompatible copyir.com Defective engine sub PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory
Defective engine PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Improper installation EEPROM copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0620 FAX image DIMM error
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com
Defective main PWB copyir.com
0650 FAX image DIMM check error
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0970 12 V power down detect Power is disconnected during sleeping copyir.com Defective power source PWB copyir.com
0980 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected copyir.com Defective power source PWB copyir.com
1000 MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 3 s copyir.com Defective MP plate elevation mechanism copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective MP lift motor copyir.com
Defective engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 1 copyir.com
Defective engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 2 copyir.com
Defective engine PWB copyir.com
1050 SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective SM lift motor copyir.com
Defective SM main PWB copyir.com
1060 PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1070 PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1100 PF lift motor 1 error
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1110 PF lift motor 2 error
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD lift motor copyir.com
Defective SD main PWB copyir.com
1250 SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
The SM multi feed sensor has detected multi feeding 5 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1410 BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps (3 times in succession) copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR decurler motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession copyir.com Deleting a block has failed three times in a row copyir.com Writing won’t complete in 200 ms after writing has commenced copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1720 Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible copyir.com The paper feeder is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1810 Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1820 Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1910 Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective SM main PWB copyir.com
Device damage of EEPROM copyir.com
1920 Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
2101 Developer motor error
After developer motor is driven, the ready signal does not turn to L within 2 s copyir.com After developer motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor copyir.com
Defective engine PWB copyir.com
2201 Drum motor steady-state error
The ready signal won’t turn to L in 2 seconds after the drum motor is started copyir.com After drum motor is stabilized, the ready signal is at the H level for 5 s continuously copyir.com The device won’t engage in ready state in 60 minutes after warming-up has began copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor copyir.com
Defective engine PWB copyir.com
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2500 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
2550 Transfer motor error
After transfer motor is driven, the ready signal does not turn to L within 2 s copyir.com After transfer motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2600 PF paper feed motor error
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2640 SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD paper feed motor copyir.com
Defective SD main PWB copyir.com
2650 SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM paper feed motor copyir.com
Defective SM main PWB copyir.com
2660 PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2670 PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective scanner motor copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LED lamp PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3300 Optical system (AGC) error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp
Defective CCD PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3310 CIS AGC error After AGC, correct input is not obtained at CIS copyir.com Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective ISC PWB copyir.com
3700 Scanner device error CCD connector inserted incorrectly copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com No response is received in 100 ms from AEF copyir.com Defective ISC PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Defective backup memory or PWB copyir.com
4001 Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4011 Polygon motor steady-state error
After polygon motor is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4101 BD initialization error
After polygon motor is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB copyir.com
Defective engine PWB copyir.com
4201 BD steady-state error
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB copyir.com
Defective engine PWB copyir.com
5101 Main high-voltage error
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower high-voltage board) copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB
Defective engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 30 s in warming up after reached to 100° C/212 °F copyir.com A temperature of less than 80°C/176 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 100°C/ 212 °F after warming up copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s copyir.com Except, the A/D value in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a low-temperature environment copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6100 Broken fuser heater wire
Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 5 wire copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature higher than 190C/374F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 5 copyir.com
Defective engine PWB copyir.com
6130 Broken fuser thermistor 5 wire
Input from fuser thermistor 5 is 992 or more (A/D value) continuously for 60 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 5 wire copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature lower than 30C/ 86F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 5 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 240C/464F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 2 copyir.com
Defective engine PWB copyir.com
6230 Broken fuser thermistor 2 wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D) continuously for 1 second during the temperature detected by the fuser thermistor 1 is 100 deg-C or more copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 2 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 100C/212F for 1 s during ready or print copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 2 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6320 Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 215C/419F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 3 copyir.com
Defective engine PWB copyir.com
6330 Broken fuser thermistor 3 wire
Fuser thermistor 3 detects a temperature lower than 20C/ 68F continuously for 1 s Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 3 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6520 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 215C/419F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB copyir.com
6530 Broken fuser thermistor 4 wire
Fuser thermistor 4 detects a temperature lower than 20C/ 68F continuously for 1 s Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 second copyir.com (Engine CPU) Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB copyir.com
6610 Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser release motor copyir.com
Defective engine PWB copyir.com
6620 IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective IH core motor copyir.com
Defective eject PWB copyir.com
Defective front PWB copyir.com
Defective engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6720 Fuser IH belt rotation error
A belt rotating pulse is not received for 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6730 Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6750 Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6760 Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6770 Fuser IH low electric power error
The preset power is less than 0 copyir.com6 times of it for 120 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6780 Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6900 Fuser belt cooling fan error
When the fuser front or rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser front or rear fan motor copyir.com
Defective engine PWB copyir.com
6940 IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH fan motor copyir.com
Defective engine PWB copyir.com
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6990 Fuser power supply incompatibility Information won’t match between the engine backup and the fuser IH PWB copyir.com Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
7001 Toner motor error
During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective toner motor copyir.com
Defective engine PWB copyir.com
7101 Toner sensor error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective toner sensor copyir.com
Defective engine PWB copyir.com
7200 Broken outer temperature sensor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7210 Short-circuited outer temperature sensor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7221 Broken LSU thermistor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor copyir.com
Defective engine PWB copyir.com
7231 Short-circuited LSU thermistor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor copyir.com
Defective engine PWB copyir.com
7241 Broken developer thermistor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor copyir.com
Defective engine PWB copyir.com
7251 Short-circuited developer thermistor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor copyir.com
Defective engine PWB copyir.com
7301 Toner hopper motor error
When the toner hopper motor is driven, toner hopper sensor does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor copyir.com
Defective toner hopper motor copyir.com
Defective engine PWB copyir.com
7401 Developer unit type mismatch error
Absence of the developer unit is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7411 Drum unit type mismatch error
Absence of the drum unit is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the drum unit is installed copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com
Defective connector cable or poor contact in the connector copyir.com
7601 ID sensor error Dark potential error
FrontDarkP and FrontDarkS are greater than 0 copyir.com80V copyir.com Light potential error FrontBrightS is smaller than FrontDarkS copyir.com FrontBrightP is smaller than FrontDarkP + 0 copyir.com5V Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7602 ID sensor error
Dark potential error RearDarkP and RearDarkS are greater than 0 copyir.com80V copyir.com Light potential error RearBrightS is smaller than RearDarkS copyir.com RearBrightP is smaller than RearDarkP + 0 copyir.com5V copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7800 Broken outer temperature sensor wire
The device did not respond for more than 5 ms during reading, in 5 times copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7901 Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB copyir.com
7911 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit copyir.com
7941 Laser scanner unit EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB copyir.com
8000 Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible copyir.com The finisher is installed with a device to which it is incompatible copyir.com
8010 Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch home position sensor copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8020 Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8030 Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF paddle sensor copyir.com
Defective DF paddle motor copyir.com
Defective DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF bundle discharge sensor copyir.com
Defective DF eject release motor copyir.com
Defective DF main PWB copyir.com
8110 DF shift motor 1 error (4000-sheet finisher)
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 1 copyir.com
Defective DF shift motor 1 copyir.com
Defective DF main PWB copyir.com
8120 DF shift motor 2 error (4000-sheet finisher)
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 2 copyir.com
Defective DF shift motor 2 copyir.com
Defective DF main PWB copyir.com
8130 DF shift release motor error (4000-sheet finisher) When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift release sensor copyir.com
Defective DF shift release motor copyir.com
Defective DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF tray sensor 3 copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF staple sensor copyir.com
Defective DF slide motor copyir.com
Defective DF main PWB copyir.com
8230 DF staple motor error 1
Staple JAM (DF) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective DF staple sensor copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8240 DF staple motor error 2
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8250 DF tray motor error 4
The lock signal of the motor is detected continuously for 10 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8300 Center-folding unit communication error (4000-sheet finisher)
Communication with the center-folding unit is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF set sensor copyir.com
Defective PWB copyir.com
8310 CF side registration motor 2 error (4000-sheet finisher)
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 2 copyir.com
Defective CF side registration motor 2 copyir.com
Defective CF main PWB copyir.com
8320 CF adjustment motor error (4000-sheet finisher)
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF adjustment sensor 1, 2 copyir.com
Defective CF adjustment motor 1, 2 copyir.com
Defective CF main PWB copyir.com
8330 CF blade motor error (4000-sheet finisher)
When initial operation, CF blade sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF blade sensor copyir.com
Defective CF blade motor copyir.com
Defective CF main PWB copyir.com
8340 CF staple motor error 1 (4000-sheet finisher)
Staple JAM (Folding unit) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective CF staple sensor copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8350 CF side registration motor 1 error (4000-sheet finisher)
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 1 copyir.com
Defective CF side registration motor 1 copyir.com
Defective CF main PWB
8360 CF main motor error (4000-sheet finisher)
During driving the motor, lock signal is detected for 1 s continuously Defective connector cable or poor contact in the connector copyir.com
Defective CF main motor copyir.com
Defective CF main PWB copyir.com
8370 CF staple motor error 2 (4000-sheet finisher)
Staple JAM (DF) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective slide sensor copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8430 Punch unit communication error
Communication failed to be established after the punch unit was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8500 Mailbox communication error (4000-sheet finisher)
Communication failed to be established after the mailbox was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8510 MB conveying motor error 1 (4000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8520 MB conveying motor error 2 (4000-sheet finisher)
When standby operation, MB home position sensor does not turn off within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor
Defective MB main PWB copyir.com
8800 Document finisher communication error
Communication failed to be established after the document finisher was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM copyir.com
Defective DF main PWB copyir.com
8930 Center-folding unit backup error (4000-sheet finisher)
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM copyir.com
Defective CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com Defective connector cable or poor contact in the connector
Defective PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Data setup failure copyir.com
Defective coin vender control PWB copyir.com
Defective PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 1 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 2 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DPSHD PWB copyir.com
9080 LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS
Defective DPSHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Defective coin vender control PWB copyir.com
9110 Coin vender error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector installed incorrectly copyir.com
Defective rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Defective pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Change jam at the pay-out copyir.com
Defective pay-out motor copyir.com
Defective pay-out sensor copyir.com
9200 DP multi feed sensor communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
9210 DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9220 DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9500, 9510, 9520 Contact the Service Administrative Division copyir.com
F000 Communication error between main PWB and operation PWB Defective main PWB copyir.com
Defective operation PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F040 Communication error between main PWB and print engine Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Communication error between main PWB and scanner engine Defective main PWB copyir.com
Defective ISC PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective ISC PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
کیو سرا میتا Kyocera-Mita TASKalfa 620
نوشته شده توسط ایراندوست بهزادC0060 Main PWB type mismatch error Poor contact in the connector terminals copyir.com
C0100 Backup memory read/write problem
• Read and write data does not match copyir.com Defective main PWB copyir.com
C0110 Backup memory data problem (main PWB)
• Data in the specified area of the backup memory does not match the specified values copyir.com Problem with the backup memory data copyir.com
Defective main PWB copyir.com
C0130 Backup memory (EEPROM) device problem
• Reading from or writing to EEPROM cannot be performed copyir.com Defective main PWB copyir.com
Device damage of EEPROM copyir.com
C0140 Backup memory (EEPROM) data problem
• Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
C0150 Backup memory device problem (Engine PWB)
• An error occurs in backup data read or write for the engine PWB copyir.com Data damage of EEPROM copyir.com
C0160 Backup memory data problem (Engine PWB)
• Data for backup data check is changed at the check after startup copyir.com Problem with the backup memory data copyir.com
Defective engine PWB copyir.com
C0170 Copy counts problem
• A checksum error is detected in the main and engine backup memories for the copy counters copyir.com Data damage of EEPROM copyir.com
Defective main PWB copyir.com
Defective engine PWB copyir.com
C0180 Machine number mismatch error
• Machine number of main PWB and engine PWB does not match copyir.com Data damage of EEPROM copyir.com
C0210 CPU communication problem
• Synchronization cannot be taken between the main CPU and engine CPU copyir.com Defective main PWB copyir.com
Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
C0220 CPU communication problem
• Synchronization cannot be taken between the main CPU and scanner CPU copyir.com Defective main PWB copyir.com
Poor contact in the connector terminals copyir.com
Defective scanner PWB copyir.com
C0240 Printer board* communication problem
• The printer board does not respond 120 seconds after the power is turned on copyir.com Poor contact in the connector terminals copyir.com
DIMM installed incorrectly copyir.com
Defective main PWB or printer board copyir.com
C0250 Network scanner board* communication problem
• The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more copyir.com
• The response to the communication command transmitted to the network scanner does not return 75 s or more copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB or network scanner board copyir.com
C0330 Relay board communication problem Poor contact in the connector terminals copyir.com
C0410 DP communication problem
• There is no reply after 5 retries at communication or a communication error occurs copyir.com Poor contact in the connector terminals copyir.com
Defective DP main PWB copyir.com
C0420 Side feeder* communication error
• A communication error from side feeder is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective side feeder main PWB copyir.com
C0440 Document finisher communication problem
• A communication error from document finisher is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective finisher main PWB copyir.com
C0460 Duplex unit communication problem
• A communication error from duplex section is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective duplex PWB copyir.com
C0500 Paper feed unit communication error (cassette 1 and 2)
• A communication error is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
C0510 Paper feed unit communication error (cassette 3 and 4)
• A communication error is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
C0610 Bitmap problem
• The DIMM on the scanner main PWB does not operate correctly copyir.com Defective main PWB copyir.com
C0630 DMA problem
• DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time copyir.com Defective main PWB copyir.com
C0640 Hard disk problem
• The hard disk cannot be accessed copyir.com Poor contact in the connector terminals copyir.com
Defective hard disk copyir.com
Defective main PWB copyir.com
Defective cable copyir.com
C0700 Side feeder EEPROM error
• An error occurs in EEPROM (U4) data read or write for the side feeder main PWB copyir.com Defective side feeder main PWB copyir.com
C0750 Document finisher* EEPROM error
• A backup memory error is received in serial communication data from the finisher copyir.com Defective optional document finisher copyir.com
C0760 Punch unit EEPROM error
• An error occurs in EEPROM data read or write for the punch PWB copyir.com Defective punch PWB copyir.com
C0770 Centerfold unit* EEPROM error
• An error occurs in EEPROM data read or write for the centerfold unit main PWB copyir.com Defective centerfold unit main PWB copyir.com
C0800 Image processing problem
• JAM05 is detected twice copyir.com Defective main PWB copyir.com
C0960 Developing unit EEPROM error
• An error occurs in EEPROM data read or write for the developing unit copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective developing unit copyir.com
C0970 Cleaning unit EEPROM error
• An error occurs in EEPROM data read or write for the cleaning unit copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective cleaning unit copyir.com
C1010 Lift motor 1 error
• When cassette 1 is inserted, lift limit switch 1 does not turn on within 33 s of lift motor 1 turning on copyir.com This error is detected four times successively copyir.com
• During copying, lift limit switch 1 does not turn on within 1 s of lift motor 1 turning on copyir.com This error is detected four times successively copyir.com Broken gears or couplings of lift motor 1 copyir.com
Defective lift motor 1 copyir.com
Poor contact of lift motor 1 connector terminals copyir.com
Defective lift limit switch 1 copyir.com
Poor contact of lift limit switch 1 connector terminals copyir.com
Defective deck PWB copyir.com
C1020 Lift motor 2 error
• When cassette 2 is inserted, lift limit switch 2 does not turn on within 33 s of lift motor 2 turning on copyir.com This error is detected four times successively copyir.com
• During copying, lift limit switch 2 does not turn on within 1 s of lift motor 2 turning on copyir.com This error is detected four times successively copyir.com Broken gears or couplings of lift motor 2 copyir.com
Defective lift motor 2 copyir.com
Poor contact of lift motor 2 connector terminals copyir.com
Defective lift limit switch 2 copyir.com
Poor contact of lift limit switch 2 connector terminals copyir.com
Defective deck PWB copyir.com
C1030 Lift motor 3 error
• When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on copyir.com This error is detected four times successively copyir.com
• During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on copyir.com This error is detected four times successively copyir.com Broken gears or couplings of lift motor 3 copyir.com
Defective lift motor 3 copyir.com
Poor contact of lift motor 3 connector terminals copyir.com
Defective lift limit switch 3 copyir.com
Poor contact of lift limit switch 3 connector terminals copyir.com
Defective casette PWB copyir.com
C1040 Lift motor 4 error
• When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on copyir.com This error is detected four times successively copyir.com
• During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on copyir.com This error is detected four times successively copyir.com Broken gears or couplings of lift motor 4 copyir.com
Defective lift motor 4 copyir.com
Poor contact of lift motor 4 connector terminals copyir.com
Defective lift limit switch 4 copyir.com
Poor contact of lift limit switch 4 connector terminals copyir.com
Defective casette PWB copyir.com
C1140 Side feeder lift motor going up error (optional side feeder)
• Upper limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding) copyir.com This error is detected four times successively copyir.com Poor contact of upper limit detection switch connector terminals copyir.com
Defective side feeder main PWB copyir.com
Defective side feeder lift motor copyir.com
C1150 Side feeder lift motor going down error (optional side feeder)
• Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding) copyir.com This error is detected four times successively copyir.com Poor contact of lower limit detection switch connector terminals copyir.com
Defective side feeder main PWB copyir.com
Defective side feeder lift motor copyir.com
C1200 Duplex side registration motor error
• The duplex side registration home position sensor does not detect the home position of the side registration guide copyir.com Defective duplex side registration home position sensor copyir.com
Defective duplex side registration motor copyir.com
Defective duplex PWB copyir.com
C2100 Developing motor error
• LOCK signal remains high for 1 s, 1 s after the developing motor has turned on copyir.com Poor contact in the developing motor connector terminals copyir.com
Defective developing motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective duplex PWB copyir.com
C2200 Drive motor error
• LOCK signal remains high for 1 s, 1 s after the drive motor has turned on copyir.com Poor contact in the drive motor connector terminals copyir.com
Defective drive motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective deck PWB or engine PWB copyir.com
C2250 Cleaning motor error
• LOCK signal remains high for 1 s, 200 ms after the cleaning motor has turned on copyir.com Poor contact in the drive motor connector terminals copyir.com
Defective cleaning motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective engine PWB copyir.com
C2300 Fuser motor error
• LOCK signal remains high for 1 s, 1 s after the fuser motor has turned on copyir.com Poor contact in the fuser motor connector terminals copyir.com
Defective fuser motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective duplex PWB or engine PWB copyir.com
C2550 Transfer motor error
• LOCK signal remains high for 1 s, 1 s after the transfer motor has turned on copyir.com Poor contact in the transfer motor connector terminals copyir.com
Defective transfer motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective cassette PWB or engine PWB copyir.com
C2640 Side feeder drive motor error Overloaded side feeder drive motor
Defective side feeder drive motor copyir.com
Defective side feeder main PWB copyir.com
C2720 PTC cleaning motor error
• LOCK signal remains high for 1 s, 200 ms after the PTC cleaning motor has turned on copyir.com Poor contact in the drive motor connector terminals copyir.com
Defective PTC cleaning motor rotation control circuit copyir.com
Defective drive transmission system copyir.com
Defective engine PWB copyir.com
C3100 Scanner carriage problem
• The home position is not correct when the power is turned on or at the start of copying using the MP tray copyir.com Defective scanner PWB copyir.com
Defective scanner home position switch copyir.com
Defective scanner motor copyir.com
Poor contact in the connector terminals copyir.com
Defective mirror flame, exposure lamp or scanner wire copyir.com
C3200 Exposure lamp problem
• Check the CCD input value for the lighting status of the exposure lamp 500 ms after the exposure lamp is lit and the carriage is moved to the shading position copyir.com If the exposure lamp does not light, a further 100 ms later, check the CCD input copyir.com The exposure lamp does not light after 50 retries copyir.com Defective scanner PWB copyir.com
Defective exposure lamp or inverter PWB copyir.com
Incorrect shading position copyir.com
Poor contact of the connector terminals copyir.com
Defective CCD PWB copyir.com
C3210 CIS lamp problem
• After the reading starting, when input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective DP main PWB copyir.com
Poor contact in the connector terminals copyir.com
Defective CIS copyir.com
Defective DP inverter PWB copyir.com
C3300 Optical system (AGC) problem
• After AGC, correct input is not obtained at CCD copyir.com Insufficient exposure lamp luminosity copyir.com
Defective scanner PWB copyir.com
Incorrect shading position copyir.com
CCD PWB output problem copyir.com
Poor contact of the connector terminals copyir.com
C3310 CIS (AGC) problem
• After AGC, correct input is not obtained at CIS copyir.com Defective DP main PWB copyir.com
CIS output problem copyir.com
Defective DP inverter PWB copyir.com
C3500 Communication error between scanner and SHD
• An error code is detected copyir.com Defective SHD PWB copyir.com
Poor contact in the connector terminals copyir.com
Defective scanner PWB copyir.com
C3900 Backup memory read/write error (scanner PWB)
• Read and write data does not match copyir.com Defective back up RAM or scanner PWB copyir.com
C3910 Backup memory read/write error (scanner PWB)
• Data in the specified area of the backup memory does not match the specified values copyir.com Problem with the backup memory data copyir.com
Defective scanner PWB copyir.com
C4000 Polygon motor synchronization problem
• The revolution does not reach the stable speed within 20 s of the START signal copyir.com Poor contact in the polygon motor connector terminals copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
C4010 Polygon motor steady-state problem
• The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized copyir.com Poor contact in the polygon motor connector terminals copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
C4100 BD initialization (A) problem
• When power is turned on, only laser A is output and ASIC of main PWB detects a BD error for 2000 ms copyir.com Defective laser scanner unit copyir.com
Defective main PWB copyir.com
Poor contact in connector terminals copyir.com
C4110 BD initialization (B) problem
• When power is turned on, only laser B is output and ASIC of main PWB detects a BD error for 2000 ms copyir.com Defective laser scanner unit copyir.com
Defective main PWB copyir.com
Poor contact in connector terminals copyir.com
C4120 BD initialization (C) problem
• When power is turned on, only laser C is output and ASIC of main PWB detects a BD error for 2000 ms copyir.com Defective laser scanner unit copyir.com
Defective main PWB copyir.com
Poor contact in connector terminals copyir.com
C4200 BD steady-state problem
• ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized copyir.com Defective laser diode copyir.com
Defective polygon motor copyir.com
Defective main PWB copyir.com
Poor contact in connector terminals copyir.com
C5100 Main high-voltage error
• While the main high-voltage output remote signal is on, an alarm signal is detected continuously for 400 ms copyir.com Defective high voltage PWB copyir.com
Leak of main high-voltage copyir.com
Poor contact in connector terminals copyir.com
C5500 Drum surface potential sensor problem 1
• The sensor output is 0 copyir.com5 V or less when MC REM signal is turned on copyir.com Poor contact in the drum surface potential sensor connector terminals copyir.com
Defective drum surface potential sensor copyir.com
Defective high voltage PWB copyir.com
Defective engine PWB copyir.com
C5510 Drum surface potential sensor problem 2
• The sensor output is 4 copyir.com5 V or more when the MC REM signal is turned on copyir.com Defective drum surface potential sensor copyir.com
Defective high voltage PWB copyir.com
Poor contact in the drum surface potential sensor copyir.com
C5600 Drum surface potential problem 1
• The sensor output is 4 copyir.com5 V or more copyir.com
• Potential adjustment in 30 times could not raise the potential sensor value to the predetermined copyir.com Deteriorated main charger copyir.com
Grid or main charger shield is dirty copyir.com
Defective drum surface potential sensor copyir.com
Defective high voltage PWB copyir.com
Defective engine PWB copyir.com
C5610 Drum surface potential problem 2
• The sensor output is 0 copyir.com5 V or less copyir.com
• Potential adjustment in 30 times could not lower the potential sensor value to the predetermined copyir.com Defective drum surface potential sensor copyir.com
Defective high voltage PWB copyir.com
Defective drum copyir.com
Defective engine PWB copyir.com
C6000 Fuser heater lamp break
• The fuser temperature does not increase for 40 s after the fuser heaters have been turned on for warming up copyir.com
• The fuser temperature remains below 50C/122F for 10 s continuously after the fuser heaters have been turned on during stabilization copyir.com Installation defectiveness on fuser thermistor M and S copyir.com
Defective fuser thermostat 1 or 2 copyir.com
Installation defectiveness on fuser heater L, M or S copyir.com
Broken fuser heater L, M and S wire copyir.com
Defective engine PWB
Defective AC power source PWB copyir.com
C6020 Fuser thermistor high-temperature detection error
• The fuser temperature exceeds 235C/455 F for 10 s copyir.com Installation defectiveness on fuser thermistor M and S copyir.com
Defective fuser thermistor M and S copyir.com
Defective engine PWB copyir.com
C6030 Fuser thermistor break error
• The fuser temperature remains at lower then 0C/32F for 30 s continuously when the fuser heater is on copyir.com Defective engine PWB copyir.com
Defective AC power source PWB copyir.com
Installation defectiveness on fuser thermistor M and S copyir.com
C6050 Fuser thermistor abnormal temperature detection • During copying, the temperature at the heat roller lower than 120C/248F is detected continuously for 5 s copyir.com Installation defectiveness on fuser thermistor M and S copyir.com
Operation on fuser thermostat 1 or 2 copyir.com
Installation defectiveness on fuser heater L, M or S copyir.com
Broken fuser heater L, M and S wire copyir.com
Defective engine PWB copyir.com
Defective AC power source PWB copyir.com
C6400 Zero-cross signal error
• The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s copyir.com Poor contact in the connector terminals copyir.com
Defective DC power source PWB copyir.com
Defective engine PWB
C7200 Broken internal thermistor wire
• The thermistor output value is 4 copyir.com5 V or more copyir.com Poor contact in the connector terminals copyir.com
Defective developing humidity sensor copyir.com
Defective engine PWB copyir.com
C7210 Short-circuited internal thermistor
• The thermistor input value is 0 copyir.com5 V or less copyir.com Poor contact in the connector terminals copyir.com
Defective developing humidity sensor copyir.com
Defective engine PWB copyir.com
C7300 Toner hopper problem
• During toner replenishment after toner empty has been detected, toner empty could not be cleared in 3 times of 360 s copyir.com Defective toner level detection sensor copyir.com
Poor contact in the toner level detection sensor connector terminals copyir.com
C7800 Broken external thermistor wire
• The thermistor output value is 4 copyir.com5 V or more copyir.com Poor contact in the connector terminals copyir.com
Defective humidity sensor copyir.com
C7810 Short-circuited external thermistor
• The thermistor input value is 0 copyir.com5 V or less copyir.com Poor contact in the connector terminals copyir.com
Defective humidity sensor copyir.com
Defective engine PWB
C8000 Fnisher type mismatch problem
• Absence of the finisher is detected copyir.com Different type of the finisher is installed copyir.com
C8010 Document finisher paper conveying motor problem
• The LOCK signal of the paper conveying motor is detected for more than 500 ms while the paper conveying motor is operating copyir.com However, the first 1 s after the paper conveying motor is turned on is excluded from detection copyir.com Loose connection of the paper conveying motor connector copyir.com
Defective paper conveying motor copyir.com
Defective finisher main PWB copyir.com
C8020 Document finisher punch motor problem
• The LOCK signal of the punch motor is detected for more than 500 ms while the punch motor is operating copyir.com However, the first 1 s after the punch motor is turned on is excluded from detection copyir.com Loose connection of the punch motor connector copyir.com
Defective punch motor copyir.com
Defective finisher main PWB copyir.com
C8030 Document finisher upper paper conveying belt problem
• During initialization, the intermediate tray upper sliding plate is not detected in the home position within 3 s after the belt returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the upper paper conveying belt copyir.com • When the intermediate tray upper sliding plate is operated from the home position, the upper paper conveying belt home position sensor does not turn off within 1 s copyir.com Phase shift of the upper paper conveying belt copyir.com
Malfunction of the upper paper conveying belt motor copyir.com
Malfunction of the upper paper conveying belt home position sensor copyir.com
Loose connection of the upper paper conveying belt home position sensor connector copyir.com
Incorrect insertion of the intermediate tray copyir.com
Defective finisher main PWB
C8040 Document finisher lower paper conveying belt problem
• During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt copyir.com • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s copyir.com Phase shift of the lower paper conveying belt copyir.com
Malfunction of the lower paper conveying belt motor copyir.com
Malfunction of the lower paper conveying belt home position sensor copyir.com
Loose connection of the lower paper conveying belt home position sensor connector copyir.com
Incorrect insertion of the intermediate tray copyir.com
Defective finisher main PWB copyir.com
C8140 Document finisher main tray problem
• When the main tray is not detected by the main tray upper limit detection sensor or the main tray load detection sensor within 20 s from the moment it starts ascending copyir.com
• During main tray descent, the main tray upper limit detection sensor or the main tray load detection sensor does not turn off within 500 ms after it turns on copyir.com
• During main tray ascent, the main tray upper limit detection sensor or the main tray load detection sensor stays on for more than 2 s copyir.com Loose connection of the main tray elevation motor connector copyir.com
Malfunction of the main tray elevation motor copyir.com
Malfunction of the main tray upper limit detection sensor copyir.com
Loose connection of the main tray upper limit detection sensor connector copyir.com
Malfunction of the main tray load detection sensor copyir.com
Loose connection of the main tray load detection sensor connector copyir.com
Defective finisher main PWB copyir.com
C8150 Document finisher multi job tray problem
• When the multi job tray is not detected by the multi job tray upper limit detection sensor within 20 s from the moment it starts ascending copyir.com
• During multi job tray descent, the multi job tray upper limit detection sensor does not turn off within 500 ms after it turns on copyir.com Loose connection of the multi job tray elevation motor connector copyir.com
Malfunction of the multi job tray elevation motor copyir.com
Malfunction of the multi job tray upper limit detection sensor copyir.com
Loose connection of the multi job tray upper limit detection sensor connector copyir.com
Defective finisher main PWB copyir.com
C8170 Document finisher front upper side registration guide problem
• During initialization, the front upper side registration guide is not detected in the home position within 3 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front upper side registration guide copyir.com
• When the front upper side registration guide is operated from the home position, the front upper side registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the front upper side registration guide motor connector copyir.com
Malfunction of the front upper side registration guide motor copyir.com
Malfunction of the front upper side registration guide home position sensor copyir.com
Loose connection of the front upper side registration guide home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8180 Document finisher rear upper side registration guide problem
• During initialization, the rear upper side registration guide is not detected in the home position within 3 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear upper side registration guide copyir.com
• When the rear upper side registration guide is operated from the home position, the rear upper side registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear upper side registration guide motor connector copyir.com
Malfunction of the rear upper side registration guide motor copyir.com
Malfunction of the rear upper side registration guide home position sensor copyir.com
Loose connection of the rear upper side registration guide home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8190 Document finisher lower side registration guide problem
• During initialization, the front/rear lower side registration guides are not detected in the home position within 3 s after the guide returns to the home position copyir.com JAM87 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the lower side registration guide copyir.com
• When the lower side registration guide is operated from the home position, the lower side registration home position sensor does not turn off within 500 ms copyir.com Loose connection of the lower side registration guide motor connector copyir.com
Malfunction of the lower side registration guide motor copyir.com
Malfunction of the lower side registration guide home position sensor copyir.com
Loose connection of the lower side registration guide home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8210 Document finisher front stapler problem
• During initialization, the front stapler is not detected in the home position within 500 ms after the front stapler returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front stapler copyir.com
• When the front stapler is operated from the home position, the front stapler home position sensor does not turn off within 500 ms copyir.com Loose connection of the front stapler motor connector copyir.com
Malfunction of the front stapler motor copyir.com
Malfunction of the front stapler home position sensor copyir.com
Loose connection of the front stapler home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8220 Document finisher* front clincher problem
• During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher copyir.com
• When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms copyir.com Loose connection of the front clincher motor connector copyir.com
Malfunction of the front clincher motor copyir.com
Malfunction of the front clincher home position sensor copyir.com
Loose connection of the front clincher home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8230 Document finisher rear stapler problem
• During initialization, the rear stapler is not detected in the home position within 500 ms after the rear stapler returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear stapler copyir.com
• When the rear stapler is operated from the home position, the rear stapler home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear stapler motor connector
Malfunction of the rear stapler motor copyir.com
Malfunction of the rear stapler home position sensor copyir.com
Loose connection of the rear stapler home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8240 Document finisher rear clincher problem
• During initialization, the rear clincher is not detected in the home position within 500 ms after the rear clincher returns to the home position copyir.com JAM90 is indicated the first time this problem occurs copyir.com If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear clincher copyir.com
• When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn off within 500 ms copyir.com Loose connection of the rear clincher motor connector copyir.com
Malfunction of the rear clincher motor copyir.com
Malfunction of the rear clincher home position sensor copyir.com
Loose connection of the rear clincher home position sensor connector copyir.com
Defective finisher main PWB copyir.com
C8300 Document finisher centerfold unit communication problem
• Communication with the centerfold unit is not possible although the connection is detected copyir.com Loose connection of the centerfold unit set switch connector copyir.com
Defective centerfold unit set switch copyir.com
Defective centerfold unit main PWB copyir.com
Defective finisher main PWB copyir.com
C8310 Document finisher centerfold unit side registration guide problem
• During initialization, the front/rear side registration guides are not detected in the home position within 600 ms after the guide returns to the home position copyir.com
• When the side registration guide is operated from the home position, the side registration guide home position sensor does not turn off within 100 ms copyir.com Loose connection of the side registration guide motor connector copyir.com
Malfunction of the side registration guide motor copyir.com
Malfunction of the side registration guide home position sensor copyir.com
Loose connection of the side registration guide home position sensor connector copyir.com
Defective centerfold unit main PWB copyir.com
C8320 Document finisher centerfold unit centering plate problem
• During initialization, the centering plate is not detected in the home position when the centering plate returns to the home position copyir.com Loose connection of the centering plate motor connector copyir.com
Malfunction of the centering plate motor copyir.com
Malfunction of the centering plate home position sensor copyir.com
Loose connection of the centering plate home position sensor connector copyir.com
Defective centerfold unit main PWB copyir.com
C8330 Document finisher centerfold blade problem
• During initialization, the centerfold blade is not detected in the home position within a specified period of time copyir.com Loose connection of the centerfold blade motor connector copyir.com
Malfunction of the centerfold blade motor copyir.com
Malfunction of the centerfold blade home position sensor copyir.com
Loose connection of the centerfold blade home position sensor connector copyir.com
Defective centerfold unit main PWB copyir.com
C9040 DP lift motor going up error
• The pulse count raised to 10000 at lifting, however, the DP lift upper limit switch could not be turned on copyir.com After one time retry, the DP lift upper limit switch could not be turned on copyir.comme copyir.com Loose connection of the DP lift motor connector copyir.com
Malfunction of the DP lift motor copyir.com
Malfunction of the DP lift upper limit switch copyir.com
Loose connection of the DP lift upper limit switch connector copyir.com
Defective DP main PWB copyir.com
C9050 DP lift motor going down error
• The pulse count raised to 10000 at lifting, however, the DP lift lower limit switch could not be turned on copyir.com After one time retry, the DP lift lower limit switch could not be turned on copyir.comme copyir.com Loose connection of the DP lift motor connector copyir.com
Malfunction of the DP lift motor copyir.com
Malfunction of the DP lift lower limit switch copyir.com
Loose connection of the DP lift lower limit switch connector copyir.com
Defective DP main PWB copyir.com
C9060 DP EEPROM error
• Read and write data does not match copyir.com
• Data in the specified area of the backup memory does not match the specified values copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
C9070 Communication problem between DP and SHD
• A communication error is detected copyir.com Loose connection of the SHD PWB copyir.com
Defective SHD PWB copyir.com
Defective DP main PWB copyir.com
C9080 Communication problem between DP and CIS
A communication error is detected copyir.com Loose connection of CIS copyir.com
Defective CIS copyir.com
کیو سرا میتا Kyocera-Mita TASKalfa 5551ci
نوشته شده توسط ایراندوست بهزاد0030 FAX control PWB system error
Processing with the fax software was disabled due to a software problem copyir.com FAX control PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on copyir.com 2 copyir.com Reinstall the fax software copyir.com 3 copyir.com Replace the FAX control PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com FAX control PWB (The FAX PWB installed will not be the one designed for the machine copyir.com): 1 copyir.com Install the FAX system designed for the model copyir.com 2 copyir.com Reinstall the fax software copyir.com
0080 Option printing system device error copyir.com
The version of the FPGA for Fiery control is not readable copyir.com (Defective FPGA) Defective FPGA for printing system control copyir.com: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Replace the main PWB
0100 Backup memory device error EEPROM(main PWB): 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it copyir.com 3 copyir.com Replace the main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com EEPROM(main PWB): 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Check the MAC address on the network status page copyir.com 3 copyir.com If it is blank, obtain an EEPROM with its MAC address written from the service support and install copyir.com 4 copyir.com Replace the main PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com EEPROM(Engine PWB): 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Check that the EEPROM is peroperly installed on the engine PWB and reinstall it copyir.com 3 copyir.com Replace the engine PWB copyir.com 4 copyir.com Check the EEPROM and if the data are currupted, contact the service support copyir.com
0160 Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal copyir.com EEPROM: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Execute U021 - memory initializing 3 copyir.com If the EEPROM data are currupted, contact the service support copyir.com
0170 Billing counting error
The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter copyir.com EEPROM: 1 copyir.com Check that the EEPROMs installed in the main PWB and the engine PWB are correct and, if not, use the correct EEPROM for the model copyir.com 2 copyir.com If the EEPROM data are currupted, contact the service support copyir.com
Main PWB: Replace the main PWB copyir.com
Engine PWB: Replace the engine PWB
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM: 1 copyir.com Confirm the machine data for the main and engine units by using U004 copyir.com 2 copyir.com If the serial number data of different models is alternately displayed, install the correct EEPROM in the PWB of the wrong serial number data copyir.com 3 copyir.com Contact the Service Support copyir.com
0350 Panel PWB communication error (electronic volume I2C communication error)
NACK is received during I2C communication -> retried 5 times -> rebooting command sent -> retried 5 times If NACK is still received copyir.com Operation PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Operation PWB (YC10) and Main PWB (YC6) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
Main PWB: Replace the main PWB copyir.com
0620 FAX image DIMM error
1 copyir.com The Fax image DIMM has not been installed copyir.com 2 copyir.com Fax image DIMM access error copyir.com FAX image DIMM: 1 copyir.com Install the FAX image DIMM supplied in the FAX system onto the main PWB copyir.com 2 copyir.com Firmly install the FAX image DIMM again onto the main board copyir.com 3 copyir.com Check the FAX image DIMM terminals and remove any foreign objects that may be adhered to it copyir.com 4 copyir.com Replace with a new FAX image DIMM copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com DP CIS: 1 copyir.com Reconnect the CIS signal line copyir.com 2 copyir.com Confirm that the CIS connector terminals are firmly connected copyir.com Insert the connector all the way in copyir.com 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
DP main PWB: Main PWB 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com Wiring that connects the CIS and the DP controller PWB copyir.com Wiring that connects the DP main PWB and the main PWB copyir.com 3 copyir.com Replace the DP main PWB copyir.com 4 copyir.com Replace the main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com HDD: 1 copyir.com If an abnormal noise is heard from the HDD, replace the HDD copyir.com 2 copyir.com Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal copyir.com Main PWB: YC1,YC27 YC2,YC32 (45/55 ppm model) 3 copyir.com Replace the SATA cable copyir.com 4 copyir.com Execute U024 to initialize (FULL) the HDD copyir.com 5 copyir.com If an error is detected after executing U024, replace the HDD copyir.com
Main PWB: Replace the main PWB
0650 FAX image DIMM check error
A fax image DIMM which was used with another machine is installed copyir.com FAX DIMM: 1 copyir.com Confirm that a used FAX image DIMM was used instead of the FAX image DIMM contained in the FAX system copyir.com 2 copyir.com If a DIMM that was used with other unit has been installed, execute maintenance mode U671 - Recovery FAX DIMM copyir.com 3 copyir.com Check whether the Fax DIMM is properly inserted into the socket on the main PWB copyir.com 4 copyir.com Replace with a new FAX image DIMM copyir.com
Main PWB: Replace the main PWB copyir.com
0660 Hard disk encryption key error EEPROM: 1 copyir.com Execute U004 if this occurs after the EEPROM has been changed copyir.com
HDD: 1 copyir.com If an abnormal noise is heard from the HDD, replace the HDD copyir.com 2 copyir.com Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal copyir.com Main PWB: YC1,YC27 YC2,YC32 (45/55 ppm model) 3 copyir.com Replace the SATA cable copyir.com 4 copyir.com Execute U024 to initialize (FULL) the HDD copyir.com 5 copyir.com If an error is detected after executing U024, replace the HDD copyir.com
Main PWB: Replace the main PWB
0670 Hard disk overwriting erasure error HDD: 1 copyir.com If an abnormal noise is heard from the HDD, replace the HDD copyir.com 2 copyir.com Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal copyir.com Main PWB: YC1,YC27 YC2,YC32 (45/55 ppm model) 3 copyir.com Replace the SATA cable copyir.com 4 copyir.com Execute U024 to initialize (FULL) the HDD copyir.com 5 copyir.com If an error is detected after executing U024, replace the HDD copyir.com
Main PWB: Replace the main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Main PWB: Replace the main PWB
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com FAX software: 1 copyir.com Reinstall the fax software copyir.com
FAX control PWB: 1 copyir.com Execute initializing by U600 copyir.com 2 copyir.com Replace the FAX control PWB copyir.com
0840 Faults of RTC
(“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state copyir.com The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM) copyir.com The RTC setting is older than 00:01 on January 1, 2000 copyir.com [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked copyir.com 10 minutes have been passed since the previous check copyir.com After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T copyir.com’ Battery ( main PWB): 1 copyir.com Make sure that the back-up batteries on the main PWB are not short-circuited copyir.com 2 copyir.com Reset Maintenance T by executing U906 copyir.com 3 copyir.com If the same C call is displayed when power is switched on and off, replace the back up battery copyir.com 4 copyir.com If communication error (due to a noise, etc copyir.com) is present with the RTC on the main circuit PWB, check the PWB is properly grounded copyir.com
Main PWB: Replace the main PWB
0870 PCFAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com FAX control PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on copyir.com 2 copyir.com Replace the FAX control PWB copyir.com
HDD: Execute U024 to initialize the HDD copyir.com
Main PWB: Replace the main PWB
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com FAX control PWB: 1 copyir.com Execute initializing by U600 (Refer to the FAX service manual) copyir.com 2 copyir.com Replace the FAX control PWB copyir.com
0980 24 V power down detect
If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second copyir.com Power source PWB: 1 copyir.com Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB copyir.com 2 copyir.com Replace the power source PWB
1000 MP lift motor error
If the MP lift sensor 1 (upper limit detect) or 2 (bottom detect) is not detectable to be turned on while the MP lift motor is ascending or descending copyir.com Manual feed lift base elevating mechanism: 1 copyir.com Check that the paper lift base of the manual feed tray can smoothly ascend and descent, if not, repair or replace copyir.com 2 copyir.com Check that the lift lever is located so that it can ascend or descend by the lift motor cam and that it not damaged and, if necessary, re-install or replace the manual feed table copyir.com
MP lift motor: 1 copyir.com Check that the paper elevator has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MP lift motor and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1 (YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the MP lift motor copyir.com
MP lift sensor1 MP lift sensor2: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MP lift sensor1,2 and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1(YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the MP lift sensor1 or MP lift sensor2 copyir.com
Feed PWB 2: Replace the Feed PWB 2 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
Lift motor 1: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the lift motor 1 copyir.com
Lift sensor 1: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the lift sensor1 copyir.com
Feed PWB 2: Replace the Feed PWB 2 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
Lift motor 2: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the lift motor 2 copyir.com
Lift sensor 2: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the lift sensor2 copyir.com
Feed PWB 2: Replace the Feed PWB 2 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
PF Lift motor 1: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 1 and main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com PFReplace the lift motor 1 copyir.com
PF Lift sensor 1: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor 1 and PF main PWB (YC7) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the lift sensor 1 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
PF Lift motor 2: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 2 and PF main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF Lift motor2 copyir.com
PF Lift sensor 2: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor 2 and PF main PWB (YC7) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the PF Lift sensor 2 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1050 SM lift motor error (side multi tray)
[45 ppm/55 ppm model] After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
SM Lift motor: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM Lift motor and SM main PWB (YC5) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the SM Lift motor copyir.com
SM Lift sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM Lift sensor and SM main PWB (YC7) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the SM Lift sensor copyir.com
SM main PWB: Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
1060 PF lift motor 1 error (side paper feeder)
[45 ppm/55 ppm model] After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com *:The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com PF Lift motor 1: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 1 and PF main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the lift motor 1 copyir.com
PF Lift sensor 1: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor1 and PF main PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the lift sensor 1 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1070 PF lift motor 2 error (side paper feeder)
[45 ppm/55 ppm model] After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com *:The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Cassette lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
PF Lift motor2: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 2 and PF main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF Lift motor2
PF Lift sensor2: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor 2 and PF main PWB (YC4) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com PFReplace the lift sensor2 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Paper feeder lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
PF Lift motor1: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 1 and PF main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF lift motor1 copyir.com
PF Lift sensor1: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor 1 and PF main PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the PF lift sensor1 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Paper feeder lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
PF Lift motor 2: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift motor 2 and PF main PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF Lift motor2 copyir.com
PF Lift sensor2: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF Lift sensor 2 and PF main PWB (YC4) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the PF Lift sensor 2 copyir.com
PF main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Paper feeder lift base elevating mechanism: Check that the cassette base can be manipulated smoothly, if not, repair or replace copyir.com
SD Lift motor: 1 copyir.com Check that the cassette base has been ascended copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SD Lift motor and SD main PWB (YC8) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the SD Lift motor copyir.com
SD Lift sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SD Lift sensor and SD main PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the SD Lift sensor copyir.com
SD main PWB: Replace the SD main PWB (Refer to the service manual for the paper feeder) copyir.com
1250 SM multi feed sensor communication error (side multi tray)
[45 ppm/55 ppm model] A communication error is detected 3 times in succession copyir.com Side multi tray: Check the wiring connection status with the main unit and, if necessary, try connecting it again copyir.com
SM main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM main PWB (YC1) and Engine PWB (YC19) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
[45 ppm/55 ppm model] The SM multi feed sensor has detected multi feeding 5 times successively copyir.com SM multi feed sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM multi feed sensor and SM main PWB (YC11) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the SM multi feed sensor copyir.com
SM main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1400 Rotary guide motor error
The guide sensor is not detected to be on at the home position detection with the rotary guide for three times in a row copyir.com Rotary guide motor: 1 copyir.com Check the rotary guide and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Rotary guide motor and BR PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the rotary guide motor copyir.com
BR PWB: Replace the BR PWB copyir.com
1410 Rotary de-curler error
If the de-curler won’t turn On/ Off despite it has been activated for 400 steps during waiting for the de-curler sensor to be On/Off three times in a row copyir.com Rotary de-curler motor: 1 copyir.com Check the rotary de-curler and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Rotary de-curler motor and BR PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the rotary de-curler motor copyir.com
BR PWB: Replace the BR PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
[45 ppm/55 ppm model] When writing the data, read and write data does not match 3 times in succession copyir.com Deleting a block has failed three times in a row copyir.com Writing won’t complete in 200 ms after writing has commenced copyir.com SM multi feed sensor: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM multi feed sensor and SM main PWB (YC11) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the SM multi feed sensor copyir.com
SM main PWB: Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1710 Side multi tray incompatible detection error
[30 ppm/35 ppm model] The side multi tray has been installed with a device to which it is incompatible copyir.com The side multi tray is installed with a device to which it is incompatible: Install the side multi-tray with the target model copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder: Check the wiring connection status with the main unit and, if necessary, try connecting it again copyir.com
PF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF main PWB (YC13) and Engine PWB (YC19) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1810 Side multi tray communication error
[45 ppm/55 ppm model] A communication error from side multi tray is detected 10 times in succession copyir.com Side multi tray: Check the wiring connection status with the main unit and, if necessary, try connecting it again copyir.com
SM main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM main PWB (YC1) and Engine PWB (YC19) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
Engine PWB: Check the engine software and upgrade to the latest, if necessary copyir.com Replace the engine PWB copyir.com
SM main PWB: Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
1820 Side paper feeder communication error
[45 ppm/55 ppm model] A communication error from paper feeder is detected 10 times in succession copyir.com Side paper feeder: Check the wiring connection status with the main unit and, if necessary, try connecting it again copyir.com
SM main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM main PWB (YC1) and Engine PWB (YC19) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
PF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF main PWB (YC13) and SM main PWB (YC4) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com PF main PWB (EEPROM): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 2 copyir.com Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1910 Side multi tray EEPROM error
[45 ppm/55 ppm model] When writing the data, read and write data does not match 3 times in succession copyir.com SM main PWB (EEPROM): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 2 copyir.com Replace the SM main PWB (Refer to the service manual for the paper feeder) copyir.com
1920 Side paper feeder EEPROM error
[45 ppm/55 ppm model] When writing the data, read and write data does not match 3 times in succession copyir.com PF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 2 copyir.com Replace the PF main PWB (Refer to the service manual for the paper feeder) copyir.com
1950 Intermediate transfer belt unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Transfer belt sensor: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Engine PWB (YC27) and RFID PWB (4P connector) (Check wirings on the RFID side since the signal line for the intermediate transfer belt sensor EEPROM on the engine PWB and the signal line for the toner container RFID are the same copyir.com) Intermediate transfer belt unit and Engine PWB (YC3) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Intermediate transfer belt unit copyir.com
2101 Developer motor K error
After developer motor K is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Developer unit K: 1 copyir.com Check that the developer waste lock has been released and, if not, release the lock copyir.com 2 copyir.com Check that the gears and spiral screw of the developer unit are not damaged copyir.com 3 copyir.com Confirm that the developer roller can rotate copyir.com 4 copyir.com If it won't rotate, replace the developer unit copyir.com
Developer motor K: 1 copyir.com To check the motor operation, execute DLP(K) by U030 copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer motor K and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Developer motor K copyir.com
Motor control PWB: Replace the Motor control PWB
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2103 Developer motor MCY error
After developer motor MCY is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor MCY is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Developer unit MCY: 1 copyir.com Check that the developer waste lock has been released and, if not, release the lock copyir.com 2 copyir.com Check that the gears and spiral screw of the developer unit are not damaged copyir.com 3 copyir.com Confirm that the developer roller can rotate copyir.com 4 copyir.com If it won't rotate, replace the developer unit copyir.com
Developer motor MCY: 1 copyir.com To check the motor operation, execute DLP(MCY) by U030 copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer motor MCY and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Developer motor MCY copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2201 Drum motor K steady-state error
After drum motor K is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Drum unit: 1 copyir.com Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor K: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor K and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the drum motor K copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2202 Drum motor C steady-state error
[45 ppm/55 ppm model] After drum motor C is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Drum unit: 1 copyir.com Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor C: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor C and Motor control PWB (YC4) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Drum motor C copyir.com
Motor control PWB: Replace the Motor control PWB
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2203 Drum motor MCY steadystate error
[30 ppm/35 ppm model] After drum motor MCY is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Drum unit: 1 copyir.com Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor MCY: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor MCY and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Drum motor MCY copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2203 Drum motor M steady-state error
[45 ppm/55 ppm model] After drum motor M is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Drum unit: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com copyir.com 2 copyir.com Decrease Vpp using U100 copyir.com Change “set ac gain” of U100 from Auto to mode1 copyir.com 3 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 4 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor M: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 3 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com Drum motor M and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Drum motor MCY copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2211 Drum motor K startup error
Drum motor K is not stabilized within 5 s since the motor is activated copyir.com Drum unit: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Decrease Vpp using U100 copyir.com Change “set ac gain” of U100 from Auto to mode1 copyir.com 4 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 5 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor K: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor K and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum motor K copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2212 Drum motor C startup error
[45 ppm/55 ppm model] Drum motor C is not stabilized within 5 s since the motor is activated copyir.com Drum unit: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Decrease Vpp using U100 copyir.com Change “set ac gain” of U100 from Auto to mode1 copyir.com 4 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 5 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor C: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor C and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum motor C copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
2213 Drum motor MCY startup error
[30 ppm/35 ppm model] Drum motor MCY is not stabilized within 5 s since the motor is activated copyir.com Drum unit: 1 copyir.com To check the motor operation, execute U030 Belt Meand (transfer motor) copyir.com copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Decrease Vpp using U100 copyir.com Change “set ac gain” of U100 from Auto to mode1 copyir.com 4 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 5 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor MCY: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor MCY and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum motor MCY copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2213 Drum motor M startup error
[45 ppm/55 ppm model] Drum motor M is not stabilized within 5 s since the motor is activated copyir.com Drum unit: 1 copyir.com To check the motor operation, execute Belt Mean (transfer motor) by U030 motor operation check copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Decrease Vpp using U100 copyir.com Change set ac gain of U100 from Auto to mode1 copyir.com 4 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 5 copyir.com If it won’t rotate, replace the drum unit copyir.com
Drum motor M: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Drum motor M and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum motor MCY copyir.com
Motor control PWB: Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Fuser motor: 1 copyir.com To check the motor operation, execute U030 Fuser (fuser motor) copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser motor and Feed PWB 1(YC18) Feed PWB 1(YC1) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the fuser motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Feed PWB 1: Replace the Feed PWB 1 copyir.com
Fuser unit: Replace the fuser unit copyir.com
2500 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Paper feed motor: 1 copyir.com To check the motor operation, execute U030 Feed (paper feed motor) copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the paper feed motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2600 PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com PF paper feed motor: 1 copyir.com To check the feed unit operation, execute U247 LCF- Motor ON copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF paper feed motor and PF main PWB (YC16) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the paper feed motor copyir.com
PF main PWB: Replace the PF main PWB
2610 PF paper feed motor error (paper feeder)
[45 ppm/55 ppm model] After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com PF paper feed motor: 1 copyir.com To check the feed unit operation, execute U247 2PF - Motor ON copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF paper feed motor and PF main PWB (YC16) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the paper feed motor copyir.com
PF main PWB: Replace the PF main PWB
2640 SD paper feed motor error (side deck)
[45 ppm/55 ppm model] After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com SD paper feed motor: 1 copyir.com To check the feed unit operation, execute U247 Side deck- Motor ON copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SD paper feed motor and SD main PWB (YC16) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the SD paper feed motor copyir.com
SD main PWB: Replace the SD main PWB
2650 SM paper feed motor error (side multi tray)
[45 ppm/55 ppm model] After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com SM paper feed motor: 1 copyir.com To check the feed unit operation, execute U247 SMT- Motor ON copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com SM paper feed motor and SM main PWB (YC5) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the SM paper feed motor copyir.com
SM main PWB: Replace the SM main PWB
2660 PF paper feed motor error (side large capacity feeder)
[45 ppm/55 ppm model] After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com PF paper feed motor: 1 copyir.com To check the feed unit operation, execute U247 Side LCF - Motor ON copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF paper feed motor and PF main PWB (YC16) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF paper feed motor copyir.com
PF main PWB: Replace the PF main PWB
2670 PF paper feed motor error (side paper feeder)
[45 ppm/55 ppm model] After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com PF paper feed motor: 1 copyir.com Execute Side 2PF - Motor ON of U247 feed unit operation check copyir.com 2 copyir.com Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com PF paper feed motor and PF main PWB (YC16) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the PF paper feed motor copyir.com
PF main PWB: Replace the PF main PWB
2700 3-color release motor error
When the color release motor is driven, the color release sensor does not turn on/off for 5 s copyir.com Color release motor Color release sensor (Intermediate transfer belt unit): 1 copyir.com To check the motor operation, execute U30 CMY Release copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Intermediate transfer belt unit and Engine PWB (YC3) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Intermediate transfer belt unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2730 Secondary transfer release motor error
When the transfer release motor is driven, the transfer release sensor does not turn on/off for 5 s copyir.com Transfer release motor: 1 copyir.com To check the motor operation, execute U030 Press Release copyir.com 2 copyir.com Check for broken drive gears and replace if any copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer release motor and relay PWB (YC14) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Transfer release motor copyir.com
Transfer release sensor: 1 copyir.com When abnormal noise is observed at the execution of Press Release of U030 motor operation check copyir.com 2 copyir.com Check that the sensor and its mounting board are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com 4 copyir.com Replace the Transfer release motor copyir.com
Paper conveying unit: 1 copyir.com The main-unit access drawer of the paper conveying unit has no foreign objects adhered or no distorted pins and, if necessary, repair copyir.com 2 copyir.com Check the paper conveying unit is firmly closed copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Relay PWB (YC1) and Feed PWB 1(YC14) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the paper conveying unit and execute U052 copyir.com
Feed PWB 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Feed PWB 1 (YC1) and Engine PWB (YC6) 2 copyir.com Check that the IC on the feed circuit PWB1 is not damaged (by an overcurrent or foreign object) and, if necessary, replace copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2760 Transfer motor startup error
Transfer motor is not stabilized within 5 s since the motor is activated copyir.com Transfer motor: 1 copyir.com To check the motor operation, execute U030 Belt Meand copyir.com 2 copyir.com Rotate the drive gear, the belt and the roller by the hand and check that they are not unusually loaded copyir.com 3 copyir.com Clean the Intermediate transfer belt unit copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer motor and Feed PWB 1 (YC13) Feed PWB 1(YC2) and Engine PWB (YC5) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the Transfer motor copyir.com
Feed PWB 1: Replace the Feed PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2770 Intermediate transfer belt meandering correction error
If the intermediate transfer belt position detecting sensor has derived an incorrect value copyir.com Intermediate transfer belt unit: 1 copyir.com Check that the Intermediate transfer belt unit has been properly installed so that the intermediate belt unit waste toner shutter won’t be derailed when the belt unit is strongly inserted copyir.com 2 copyir.com Reinstall the intermediate transfer belt unit copyir.com(Insert slowly all the way in copyir.com 3 copyir.com Run U468 Belt Position with B/W and confirm “ angle” (position of belt) is within the range (6 to 26) copyir.com 4 copyir.com Check that the main unit is placed perfectly horizontal copyir.com 5 copyir.com Replace the intermediate transfer belt unit copyir.com
Transfer belt sensor (Intermediate transfer belt unit): 1 copyir.com Clean the toner off of the sensor and its proximity using a blower copyir.com 2 copyir.com Check the sensor actuator are correctly positioned copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2780 Intermediate transfer belt skew correction sensor error
An abnormal value is detected to transfer skew sensor copyir.com Transfer belt skew sensor (Intermediate transfer belt unit): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com intermediate transfer belt unit and Engine PWB (YC3) 1 copyir.com Replace the intermediate transfer belt unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
2790 Intermediate transfer belt skew correction motor error
When the transfer skew motor is driven, timeouts (300 ms) were detected twice in a row copyir.com Transfer belt skew motor: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com intermediate transfer belt unit and Engine PWB (YC3) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the intermediate transfer belt unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
2810 Inner waste toner motor error
Initialized when an error is constantly observed for 2 seconds after the inner waste tonner motor is activated copyir.com An error is detected twice for 2 copyir.com5 seconds after rebooting copyir.com The lock detect signal won’t be H level three times in a row within 200 ms at 1 copyir.com25 ms cycles after the inner waste tonner motor has been driven copyir.com Waste toner box: 1 copyir.com Rotate the waste toner spiral by the hand and check that they are not unusually loaded copyir.com 2 copyir.com If the spiral won’t rotate, replace the waste toner tank copyir.com
Waste toner motor: 1 copyir.com Rotate the drive gear by the hand and check that they are not unusually loaded copyir.com 2 copyir.com Clean the drive gears and the axle holder copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Waste toner motor and Front PWB (YC16) Front PWB (YC3) and Engine PWB (YC7) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the waste toner motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2820 Intermediate transfer belt motor steady-state error
After transfer motor is stabilized, the ready signal is at the H level for 5 s continuously copyir.com The counter value obtained by timer capture is lower than 2200 for 10 times in a row copyir.com Transfer motor: 1 copyir.com To check the motor operation, execute U030 Belt Meand copyir.com 2 copyir.com Rotate the roller, driving gear by the hand and check that they are not unusually loaded copyir.com 3 copyir.com Clean the intermediate transfer belt unit copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer motor and Feed PWB 1(YC13) Feed PWB 1(YC2) and Engine PWB (YC5) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the Transfer motor copyir.com
Feed PWB 1: Replace the Feed PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2840 Intermediate transfer belt cleaning motor error
After transfer cleaning motor is driven, the ready signal won’t be L lebel within 2 s copyir.com After transfer cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Transfer cleaning motor: 1 copyir.com Rotate the roller and the drive gear by the hand and check that they are not unusually loaded copyir.com 2 copyir.com Check if the waste toner is remaining inside the cleaning unit without being disposed of copyir.com 3 copyir.com Clean inside the cleaning unit copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer cleaning motor and Engine PWB (YC3) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the transfer cleaning motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
2850 Intermediate transferbelt sensor error
The signal is not received for 100 ms in succession copyir.com Transfer motor: 1 copyir.com To check the motor operation, execute U030 Belt Meand copyir.com 2 copyir.com Rotate the roller, driving gear by the hand and check that they are not unusually loaded copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer motor and Feed PWB 1(YC13) Feed PWB 1(YC1) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Transfer motor copyir.com
Feed PWB 1: Replace the Feed PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2860 Intermediate transfer belt sub sensor error
The signal is not received for 100 ms in succession copyir.com Transfer belt sensor: 1 copyir.com To check the motor operation, execute U030 Belt Meand copyir.com 2 copyir.com Check that the drive roller for the sensor pulse can be rotated copyir.com 3 copyir.com Check that the sensor is correctly positioned copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Transfer belt sensor and intermediate transfer belt unit and Engine PWB (YC3) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the intermediate transfer belt unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
2950 Motor control PWB communication error
A communication error from the motor control PWB is detected 10 times in succession copyir.com Motor control PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Motor control PWB (YC3) and Engine PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Motor control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor copyir.com The scanner mirror frame is being locked after setup: Check whether the scanner mirror frame has been unlocked and unlock if necessary
Scanner motor: 1 copyir.com To check the scanner motor, execute U073 copyir.com 2 copyir.com Move the scanner by the hand to check whether it is unusually difficult to move copyir.com 3 copyir.com Check that the optical wire rope is not disengaged and engage the wire copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the scanner motor copyir.com
Home position sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Home position sensor and ISC PWB (YC8) 3 copyir.com Replace the home position sensor copyir.com
ISC PWB: Replace the ISC PWB and execute U411
Main PWB: Replace the main PWB
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s CIS: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Execute CCD of U061 lamp check copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the CIS and execute U091 and U411 copyir.com
DPSHD PWB: Replace the DPSHD PWB copyir.com
DP relay PWB: Replace the DP relay PWB copyir.com
3220 CCD lamp activation error
The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 1000 copyir.com CIS 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com If the LED lamp won’t light, replace the LED PWB and execut U411 copyir.com
ISC PWB: Replace the ISC PWB and execute U411 copyir.com
Main PWB: Replace the main PWB
3300 Optical system (AGC) error
One of the gains is FF or 0x89 during the CCD lamp AGC is being processed copyir.com LED lamp PWB: 1 copyir.com To check the lamp, execute U061 CCD copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com If the LED lamp won’t light, replace the LED PWB and execut U411 copyir.com
CCD PWB: Replace the ISU and execute U411
ISC PWB: Replace the ISC PWB and execute U411 copyir.com
Main PWB: Replace the main PWB copyir.com
3310 CIS AGC error
After AGC, correct input is not obtained at CIS copyir.com CIS: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com To check the lamp, execute U061 CCD copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the CIS and execute U091 and U411 copyir.com
DPSHD PWB: Replace the DPSHD PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected copyir.com ISC PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com ISC PWB (YC3) and Main PWB (YC11) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the ISC PWB and execute U411 copyir.com
Main PWB Replace the main PWB copyir.com
3600 Scanner sequence error ISC PWB: 1 copyir.com Execute U021 memory initializing copyir.com 2 copyir.com Replace the ISC PWB and execute U411 copyir.com
3700 Scanner device error CCD (ISU): Since the ISU is mounted with a CCD of different type, install the ISU that matches with the model copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com No response is received in 100 ms from AEF copyir.com ISC PWB: 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com CCD PWB (YC2) and ISC PWB (YC9) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the ISC PWB and execute U411 copyir.com
CCD PWB: Replace the ISU PWB and execute U411 copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Backup memory (ISC PWB): 1 copyir.com Turn the main power switch off and after 5 seconds, turn it on copyir.com 2 copyir.com Replace the ISC PWB and execute U411 copyir.com
4001 Polygon motor K synchronization error
After polygon motor K is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Polygon motor K (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor K and LSU relay PWB (YC4) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4002 Polygon motor C synchronization error
After polygon motor C is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Polygon motor C (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4003 Polygon motor M synchronization error
After polygon motor M is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Polygon motor M (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor M and LSU relay PWB (YC7) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4004 Polygon motor Y synchronization error
After polygon motor Y is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Polygon motor Y (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor Y and LSU relay PWB (YC11) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4011 Polygon motor K steadystate error
After polygon motor K is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Polygon motor K (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor K and LSU relay PWB (YC4) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4012 Polygon motor C steadystate error
After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Polygon motor C (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4013 Polygon motor M steadystate error
After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Polygon motor M (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor M and LSU relay PWB (YC7) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: Check the engine software and upgrade to the latest, if necessary copyir.com Replace the engine PWB
4014 Polygon motor Y steadystate error
After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Polygon motor Y (LSU): 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Polygon motor Y and LSU relay PWB (YC11) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4101 BD initialization error K
After polygon motor K is driven, the BD signal is not detected for 1 s copyir.com PD PWB K (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC5) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4102 BD initialization error C
After polygon motor C is driven, the BD signal is not detected for 1 s copyir.com PD PWB C (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
4103 BD initialization error M
After polygon motor M is driven, the BD signal is not detected for 1 s copyir.com PD PWB M (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4104 BD initialization error Y
After polygon motor Y is driven, the BD signal is not detected for 1 s copyir.com PD PWB Y (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4201 BD steady-state error K
The BD signal is not detected copyir.com PD PWB K (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC5) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
4202 BD steady-state error C
The BD signal is not detected copyir.com PD PWB C (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4203 BD steady-state error M
The BD signal is not detected copyir.com PD PWB M (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
4204 BD steady-state error Y
The BD signal is not detected copyir.com PD PWB Y (LSU): 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2 copyir.com If the FCC wiring is disconnected, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
4300 Polygon motor phase error
ASIC won’t settle in completion of phase adjustment for 2 s after a BD signal is detected copyir.com Laser scanner unit: Replace the laser scanner unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
4600 LSU cleaning motor error
After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s copyir.com After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com LSU cleaning motoror: 1 copyir.com Execute LSU cleaning using Adjustment/Maintenance of the system menu copyir.com 2 copyir.com Rotate the drive gear and the cleaning spiral by the hand and check that they are not unusually loaded, and replace if it is damaged copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com LSU cleaning motor and Engine PWB (YC21) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the LSU cleaning motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
5101 Main high-voltage error K
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board) copyir.com Drum unit: 1 copyir.com Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com Check that the discharger lamp is properly connected copyir.com 4 copyir.com If it won’t rotate, replace the drum unit copyir.com
Charger roller unit: 1 copyir.com Check that the high-voltage contacts are not distorted or adhered with foreign objects copyir.com 2 copyir.com Reinstall the chrager roller unit copyir.comOr, replace the charger roller unit copyir.com
High voltage PWB 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com High voltage PWB 1(YC4)*1,(YC3)*2 and Engine PWB (YC17) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the High voltage PWB 1 copyir.com *1:45 ppm model/ 55ppm model *2:30ppm model/ 35ppm model
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
5102 Main high-voltage error C
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board) copyir.com Drum unit: 1 copyir.com Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com Check that the discharger lamp is properly connected copyir.com 4 copyir.com If it won’t rotate, replace the drum unit copyir.com
Charger roller unit: 1 copyir.com Check that the high-voltage contacts are not distorted or adhered with foreign objects copyir.com 2 copyir.com Reinstall the chrager roller unit copyir.comOr, replace the charger roller unit copyir.com
High voltage PWB 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com High voltage PWB 1(YC2) and Engine PWB (YC16) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the High voltage PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
5103 Main high-voltage error M
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board) copyir.com Drum unit: 1 copyir.com Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com Check that the discharger lamp is properly connected copyir.com 4 copyir.com If it won’t rotate, replace the drum unit copyir.com
Charger roller unit: 1 copyir.com Check that the high-voltage contacts are not distorted or adhered with foreign objects copyir.com 2 copyir.com Reinstall the chrager roller unit copyir.comOr, replace the charger roller unit copyir.com
High voltage PWB 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com High voltage PWB 1(YC3) and Engine PWB (YC17) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the High voltage PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
5104 Main high-voltage error Y
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board) copyir.com Drum unit: 1 copyir.com Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate copyir.com 2 copyir.com Confirm that the drum or the drum screw can rotate copyir.com 3 copyir.com Check that the discharger lamp is properly connected copyir.com 4 copyir.com If it won’t rotate, replace the drum unit copyir.com
Charger roller unit: 1 copyir.com Check that the high-voltage contacts are not distorted or adhered with foreign objects copyir.com 2 copyir.com Reinstall the chrager roller unit copyir.comOr, replace the charger roller unit copyir.com
High voltage PWB 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com High voltage PWB 1(YC1) and Engine PWB (YC16) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the High voltage PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Fuser unit: 1 copyir.com Check that no paper jam is present copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com (Deteriorated sensitivity due to the toner adhered to the center thermistor copyir.com)
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6020 Abnormally high fuser Center thermistor 1 temperature
Fuser center thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6030 Broken fuser center thermistor 1 wire
Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s copyir.com Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds copyir.com Fuser unit: 1 copyir.com Check that no paper jam is present copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com (Deteriorated sensitivity due to the toner adhered to the center thermistor copyir.com)
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the Fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB (YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
6050 Abnormally low fuser center thermistor 1 temperature
Fuser center thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print copyir.com The temperature of thermistor 1 is detected to be less than 70°C/158°F for more than one second during lowpower mode copyir.com Power source: 1 copyir.com Check that the operating voltage falls within +/-10% copyir.com 2 copyir.com Check no voltage drop is caused copyir.com The heater is deactivated at 70V or lower copyir.com 3 copyir.com Relocate the AC outlet that supplies power copyir.com
Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the Fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6120 Abnormally high fuser press thermistor 4 temperature
Fuser press thermistor 4 detects a temperature higher than 190°C/374°F for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6130 Broken fuser press thermistor 4 wire
Input from fuser press thermistor 4 is 992 or more (A/D value) continuously for 60 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6150 Abnormally low fuser press thermistor 4 temperature Fuser press thermistor 4 detects a temperature lower than 30°C/86°F for 1 s after warming up copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 2 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6200 Broken fuser edge heater wire
Fuser edge thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser edge thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6220 Abnormally high fuser edge thermistor 2 temperature
Fuser edge thermistor 2 detects a temperature higher than 245°C/473°F for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6230 Broken fuser edge thermistor 2 wire
The Input signal from the fuser edge thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser edge thermistor 1 is higher than 100°C/212°F during warming up copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
6250 Abnormally low fuser edge thermistor 2 temperature
Fuser edge thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print copyir.com Fuser edge thermistor 2 detects a temperature lower than 50°C/122°F for 1 s during low power mode copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
6320 Abnormally high fuser middle thermistor 3 temperature
Fuser middle thermistor 3 detects a temperature higher than 205°C/401°F for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6330 Broken fuser center thermistor 3 wire
Fuser center thermistor 3 detects a temperature lower than 20°C/68°F continuously for 1 s copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 s copyir.com (Engine CPU) Fuser motor: 1 copyir.com To check the motor operation, execute U030 Fuser copyir.com 2 copyir.com Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the fuser motor copyir.com
Fuser belt sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6610 Fuser release sensor error
The fusing pressure release sensor won’t send an off signal in 5 seconds since a pressure release instruction is given for the fusing pressure motor copyir.com The fusing pressure release sensor won’t send an on signal in 5 seconds since a pressure instruction is given for the fusing pressure motor copyir.com Fuser release motor: 1 copyir.com To check the motor operation, execute U030 Fuser Release copyir.com 2 copyir.com Check that the drive gear can be rotated and the separation is possible copyir.com 3 copyir.com If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the fuser unit and execute U167 counter clear copyir.com
Fuser release sensor: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Check that the sensor is not contaminated or damaged copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6720 Fuser IH belt rotation error
While driving, the pulse count is less than 3 for 2 seconds during the input to the rotation pulse signal is 200 msec copyir.com Fuser motor: 1 copyir.com To check the motor operation, execute U030 Fuser copyir.com 2 copyir.com Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the fuser motor copyir.com
Fuser belt sensor: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser unit and execute U167 counter clear copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com Replace the fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6730 Abnormally high fuser IH PWB temperature 1 (IGBT1)
The input detect temperature is higher than 115°C/221 °F copyir.com Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2 (IGBT2)
The input detect temperature is higher than 115°C/221 °F copyir.com Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6750 Fuser IH output over-current error
The output current of IH CPU is higher than 90A for 10 ms in succession copyir.com Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6760 Fuser IH input over-current error
The input current of IH CPU is higher than 20A(100V/120V), 10A(200V) for 100 ms in succession copyir.com Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6770 Fuser IH low electric power error
Less than 0 copyir.com6 times of the preset power is detected for 120 ms in succession after the IH heater remote has turned on copyir.com Fuser unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser unit and Fuser IH PWB (YC6) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser IH unit copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser IH PWB copyir.com
Fuser IH unit: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the fuser IH unit copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6900 Fuser belt cooling fan error
When the fuser edge fan motor 1 , 2 is driven, alarm signal is detected for 5 s continuously copyir.com Fuser edge fan motor 1, 2: 1 copyir.com To check the fan motor operation, execute U037 Fuser Edge copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser edge fan motor 1 and Engine PWB (YC26) Fuser edge fan motor 2 and Fuser PWB (YC2) Fuser PWB (YC1) and Engine PWB (YC26) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the fuser unit and execute U167 counter clear copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6910 Engine software ready error
The device won’t engage in ready state in 60 minutes after warming-up has began copyir.com (A previous timeout process has not been cancelled copyir.com) Engine PWB: 1 copyir.com Turn the main power switch off and after 5 seconds, turn it on copyir.com 2 copyir.com Reinstall the engine software copyir.com 3 copyir.com Replace the engine PWB copyir.com
6920 Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Fuser front fan motor: 1 copyir.com To check the fan motor operation, execute U037 IH Coil copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser front fan motor and Front PWB (YC4) Front PWB (YC3) and Engine PWB (YC7) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the fuser front fan motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6930 Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Fuser rear fan motor: 1 copyir.com To check the fan motor operation, execute U037 Fuser Coling copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser rear fan motor and Engine PWB (YC26) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the fuser rear fan motor copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6940 IH PWB cooling fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com IH fan motor: 1 copyir.com To check the fan motor operation, execute U037 IH Pwb copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com IH fan motor and Feed PWB 1(YC11) Feed PWB 1(YC2) and Engine PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the IH fan motor copyir.com
Feed PWB 1: Replace the Feed PWB1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Power source PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Power source PWB (YC9) and Feed PWB 1(YC4) Power source PWB (YC3) and Fuser IH PWB (YC1) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com If the +24V output is not given by the power source PWB (YC9), replace the power source PWB copyir.com
Feed PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Power source PWB (YC3) and Fuser IH PWB (YC1) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com If the +24V output is not given by the feed PWB1 (YC27), replace the feed PWB1 copyir.com
Fuser IH PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Fuser IH PWB(YC4) and Engine PWB (YC26) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Fuser IH PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
6960 Current PWB error
The power current is greater than 1A for 5 seconds continuously despite that 500W was indicated as the fuser power during power-up copyir.com (45 ppm/ 55 ppm model only) Current PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Current PWB(YC17) and Feed PWB2 (YC13) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Current PWB copyir.com
6990 Fuser power supply incompatibility
Information won’t match between the engine backup and the fuser IH PWB copyir.com Differences in settings after initialization: When this has happened after initialization using U021, make settings identical with the voltages on the IH PWB using U169 copyir.com
Fuser IH PWB: Replace with a fuser IH PWB specifically designed with the standard voltage copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7001 Toner motor K error
A state that the pulse is not detected at the pulse sensor for 200 ms has occurred more than 15 times in a row during the toner motor K is driven copyir.com A state that the TMOT_LOCK signal becomes H (locked) is detected after 200 ms when the toner motor K is driven has occurred 15 sets in total copyir.com Toner container K: 1 copyir.com Check that the spiral screw of the toner container can be rotated by the hand copyir.com 2 copyir.com Check for broken gears and replace if any copyir.com
Toner motor K: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor K and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor K copyir.com
Screw sensor K: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Screw sensor K and Engine PWB (YC27) 3 copyir.com Replace the screw sensor K copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7002 Toner motor C error
A state that the pulse is not detected at the pulse sensor for 200 ms has occurred more than 15 times in a row during the toner motor C is driven copyir.com A state that the TMOT_LOCK signal becomes H (locked) is detected after 200 ms when the toner motor C is driven has occurred 15 sets in total copyir.com Toner container C: 1 copyir.com Check that the spiral screw of the toner container can be rotated by the hand copyir.com 2 copyir.com Check for broken gears and replace if any copyir.com
Toner motor C: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor C and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor C copyir.com
Screw sensor C: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Screw sensor C and Engine PWB (YC27) 3 copyir.com Replace the screw sensor C copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
7003 Toner motor M error
A state that the pulse is not detected at the pulse sensor for 200 ms has occurred more than 15 times in a row during the toner motor M is driven copyir.com A state that the TMOT_LOCK signal becomes H (locked) is detected after 200 ms when the toner motor M is driven has occurred 15 sets in total copyir.com Toner container M: 1 copyir.com Check that the spiral screw of the toner container can be rotated by the hand copyir.com 2 copyir.com Check for broken gears and replace if any copyir.com
Toner motor M: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor M and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor M copyir.com
Screw sensor M: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Screw sensorM and Engine PWB (YC27) 3 copyir.com Replace the screw sensor M copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7004 Toner motor Y error
A state that the pulse is not detected at the pulse sensor for 200 ms has occurred more than 15 times in a row during the toner motor Y is driven copyir.com A state that the TMOT_LOCK signal becomes H (locked) is detected after 200 ms when the toner motor Y is driven has occurred 15 sets in total copyir.com Toner container Y: 1 copyir.com Check that the spiral screw of the toner container can be rotated by the hand copyir.com 1 copyir.com Check for broken gears and replace if any copyir.com
Toner motor Y: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor Y and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor Y copyir.com
Screw sensor Y: 1 copyir.com Check that the sensor is correctly positioned copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Screw sensor Y and Engine PWB (YC27) 3 copyir.com Replace the screw sensor Y copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7101 Toner sensor K error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Failure of locking the developer waste slot at setup:
If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet copyir.com
Toner sensor K: 1 copyir.com Check the toner sensor output by U155 copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner sensor K and Front PWB (YC9) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Check that the gears of the developer unit K are not damaged and the spiral can rotate copyir.com 5 copyir.com Replace the Developer unit K copyir.com
Toner motor K: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor K and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor K copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7102 Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Failure of locking the developer waste slot at setup:
If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet copyir.com
Toner sensor C: 1 copyir.com Check the toner sensor output by U155 copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Check that the gears of the developer unit C are not damaged and the spiral can rotate copyir.com 5 copyir.com Replace the Developer unit C copyir.com
Toner motor C: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor C and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor C copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7103 Toner sensor M error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Failure of locking the developer waste slot at setup:
If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet copyir.com
Toner sensor M: 1 copyir.com Check the toner sensor output by U155 copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Check that the gears of the developer unit M are not damaged and the spiral can rotate copyir.com 5 copyir.com Replace the Developer unit M copyir.com
Toner motor M: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor M and ?Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor M copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7104 Toner sensor Y error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Failure of locking the developer waste slot at setup:
If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet copyir.com
Toner sensor Y: 1 copyir.com Check the toner sensor output by U155 copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Check that the gears of the developer unit Y are not damaged and the spiral can rotate copyir.com 5 copyir.com Replace the Developer unit Y copyir.com
Toner motor Y: 1 copyir.com Draw out the toner container and execute U135 to check the toner motor operation copyir.com 2 copyir.com Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Toner motor Y and Engine PWB (YC27) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the Toner motor Y copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire
The sensor input sampling is greater than 230 copyir.com Outer temperature sensor 2:
1 copyir.com Confirm Ext/Int is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Outer temperature sensor 2 and Front PWB (YC19) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the outer temperature sensor 2 copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7210 Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69 copyir.com Outer temperature sensor 2:
1 copyir.com Confirm Ext/Int is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Outer temperature sensor 2 and Front PWB (YC19) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the outer temperature sensor 2 copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7221 Broken LSU thermistor K wire
The sensor input sampling is greater than 230 copyir.com LSU thermistor K: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC5) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7222 Broken LSU thermistor C wire
The sensor input sampling is greater than 230 copyir.com LSU thermistor C: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7223 Broken LSU thermistor M wire
The sensor input sampling is greater than 230 copyir.com LSU thermistor M: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7224 Broken LSU thermistor Y wire
The sensor input sampling is greater than 230 copyir.com LSU thermistor Y: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7231 Short-circuited LSU thermistor K
The sensor input sampling is less than 69 copyir.com LSU thermistor K: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC5) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: Replace the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7232 Short-circuited LSU thermistor C
The sensor input sampling is less than 69 copyir.com LSU thermistor C: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7233 Short-circuited LSU thermistor M
The sensor input sampling is less than 69 copyir.com LSU thermistor M: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7234 Short-circuited LSU thermistor Y
The sensor input sampling is less than 69 copyir.com LSU thermistor Y: 1 copyir.com Confirm LSU is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: REPLACE the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7241 Broken developer thermistor K wire
The sensor input sampling is greater than 230 copyir.com Developer thermistor K: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit K and Front PWB (YC9) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit K copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7242 Broken developer thermistor C wire
The sensor input sampling is greater than 230 copyir.com Developer thermistor C: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit C copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7243 Broken developer thermistor M wire
The sensor input sampling is greater than 230 copyir.com Developer thermistor M: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit M copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7244 Broken developer thermistor Y wire
The sensor input sampling is greater than 230 copyir.com Developer thermistor Y: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit Y copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7251 Short-circuited developer thermistor K
The sensor input sampling is less than 69 copyir.com Developer thermistor K: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit K and Front PWB (YC9) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit K copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7252 Short-circuited developer thermistor C
The sensor input sampling is less than 69 copyir.com Developer thermistor C: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit C copyir.com
Front PWB: Replace the front
PWB copyir.comEngine: PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7253 Short-circuited developer thermistor M:The sensor input sampling is less than 69 copyir.com Developer thermistor M: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit M:
7254 Short-circuited developer thermistor Y wire
The sensor input sampling is less than 69 copyir.com Developer thermistor Y: 1 copyir.com Confirm Developing is displayed by U139 temperature and humidity copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the Developer unit Y copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7401 Developer unit K type mismatch error
Improper adaptation of the machine and developer unit K is detected copyir.com Different type of the developer unit is installed: Install the developer unit of the correct type copyir.com
Developer unit K: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit K and Front PWB (YC9) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
7402 Developer unit C type mismatch error
Improper adaptation of the machine and developer unit C is detected copyir.com Different type of the developer unit is installed: Install the developer unit of the correct type copyir.com
Developer unit C: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
7403 Developer unit M type mismatch error
Improper adaptation of the machine and developer unit M is detected copyir.com Different type of the developer unit is installed: Install the developer unit of the correct type copyir.com
Developer unit M: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
7404 Developer unit Y type mismatch error
Improper adaptation of the machine and developer unit Y is detected copyir.com Different type of the developer unit is installed: Install the developer unit of the correct type copyir.com
Developer unit Y: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
7601 ID sensor 1 error
An abnormal value is detected in the input data to ID sensor 1 copyir.com Dark potential error FrontDarkP and FrontDarkS are greater than 0 copyir.com80V copyir.com Light potential error FrontBrightS is smaller than FrontDarkS copyir.com FrontBrightP is smaller than [FrontDarkP + 0 copyir.com5V] copyir.com ID sensor1 (front): 1 copyir.com Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference copyir.com 2 copyir.com Detach the imtermediate intermediate transfer belt unit and clean the ID sensor on its surface copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com ID sensor 1 (front) and Feed PWB 1(YC10) Feed PWB 1(YC1) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
Feed PWB: 1 Replace the Feed PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7602 ID sensor 2 error
Dark potential error RearDarkP and RearDarkS are greater than 0 copyir.com80V copyir.com Light potential error RearBrightS is smaller than RearDarkS copyir.com RearBrightP is smaller than [RearDarkP + 0 copyir.com5V] copyir.com ID sensor 2 (rear): 1 copyir.com Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference copyir.com 2 copyir.com Detach the imtermediate intermediate transfer belt unit and clean the ID sensor on its surface copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com ID sensor2 (rear) and Feed PWB 1(YC10) Feed PWB 1(YC1) and Engine PWB (YC6) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com
Feed PWB: 1 Replace the Feed PWB 1 copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7800 Broken outer temperature sensor 1 wire
The device did not respond for more than 5 ms during reading, in 5 times copyir.com Outer temperature sensor 1: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Outer temperature sensor 1 and Front PWB (YC16) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Outer temperature sensor 1 copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DR PWB-K: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DR PWB-K and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum unit K copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DR PWB- C: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DR PWB- C and Front PWB (YC12) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum unit C copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB5 times copyir.com
7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DR PWB- M: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DR PWB- M and Front PWB (YC10) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum unit M copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DRPWB- Y: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DRPWB- Y and Front PWB (YC14) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Drum unit Y copyir.com
Front PWB Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
7911 Developer unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit K: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit K and Front PWB (YC9) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Developer unit K copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7912 Developer unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit C: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Developer unit C copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB5 times copyir.com
7913 Developer unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit M: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Developer unit M copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7914 Developer unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit Y: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Developer unit Y copyir.com
Front PWB: Replace the front PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB5 times copyir.com
7941 Laser scanner unit K EEPROM error
[35 ppm/ 45 ppm/ 55 ppm model] Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com APC PWB K: 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com APC PWB K and LSU relay PWB (YC5) LSU relay PWB (YC2) and Engine PWB (YC11) 2 copyir.com If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: Replace the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
7942 Laser scanner unit C EEPROM error
[35 ppm/ 45 ppm/ 55 ppm model] Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com APC PWB C: 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com APC PWB C and LSU relay PWB (YC10) LSU relay PWB (YC2) and Engine PWB (YC11) 2 copyir.com If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: Replace the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB5 times copyir.com
7943 Laser scanner unit M EEPROM error
[35 ppm/ 45 ppm/ 55 ppm model] Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com APC PWB M: 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com APC PWB M and LSU relay PWB (YC8) LSU relay PWB (YC2) and Engine PWB (YC11) 2 copyir.com If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring copyir.com 3 copyir.com Replace 1-5-43the laser scanner unit copyir.com
LSU relay PWB: Replace the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB5 times copyir.com
7944 Laser scanner unit Y EEPROM error
[35 ppm/ 45 ppm/ 55 ppm model] Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com APC PWB Y 1 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com APC PWB Y and LSU relay PWB (YC12) LSU relay PWB (YC2) and Engine PWB (YC11) 2 copyir.com If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring copyir.com 3 copyir.com Replace the laser scanner unit copyir.com
LSU relay PWB: Replace the LSU relay PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
8010 Punch motor 1 error
When the punch motor is driven, punch home position sensor does not turn on within 200 ms Punch motor 1 copyir.com Execute U240 Motor - Punch to check the finisher operation copyir.com 2 copyir.com Manipulate the punch up and down to check it can smoothly move up and down copyir.com 3 copyir.com Check that the drive from the motor reaches the punch cam copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch motor and Punch PWB (YC4) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the punch motor copyir.com
Punch home position sensor: 1 copyir.com Execute U241 Punch - Punch HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch home position sensor and Punch PWB (YC8) 4 copyir.com Replace the Punch home position sensor copyir.com
Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7) (4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8) (1000-sheet finisher) 2 copyir.com Replace the punch PWB copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8020 Punch motor 2 error
Home position is not obtained in 3 s after home position is initialized or in standby copyir.com Punch motor: 1 copyir.com Execute U240 Motor - Punch to check the finisher operation copyir.com 2 copyir.com Manipulate the punch up and down to check it can smoothly move up and down copyir.com 3 copyir.com Check that the drive from the motor reaches the punch cam copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch motor and Punch PWB (YC4) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the punch motor copyir.com
Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7)(4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8)(1000-sheet finisher) 2 copyir.com Replace the punch PWB copyir.com
DF main PWB: Replace the DF main PWB
8030 Punch motor 3 error
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com{? Punch motor: 1 copyir.com Execute U240 Motor - Punch to check the finisher operation copyir.com 2 copyir.com Manipulate the punch up and down to check it can smoothly move up and down copyir.com 3 copyir.com Check that the drive from the motor reaches the punch cam copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch motor and Punch PWB (YC4) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the punch motor copyir.com
Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7) (4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8) (1000-sheet finisher) 2 copyir.com Replace the punch PWB copyir.com
DF main PWB: Replace the DF main PWB
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com DF paddle motor: 1 copyir.com Execute U240 Motor - Beat to check the finisher operation copyir.com 2 copyir.com Check that the paddle can rotate copyir.com 3 copyir.com Check that the drive from the motor reaches the paddle copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF paddle motor and DF main PWB (YC15) (4000-sheet finisher) DF paddle motor and DF main PWB (YC11) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF paddle motor copyir.com
DF paddle sensor: 1 copyir.com Execute U241 Finisher - Bundle Eject HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting board are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF paddle sensor and DF main PWB (YC22) (4000-sheet finisher) DF paddle sensor and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com Replace the DF paddle sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com DF eject release motor DF bundle discharge unit sensor: 1 copyir.com Execute Motor - Eject Unlock (Full) of U240 finisher operation check copyir.com 2 copyir.com Check that the eject guide of the process tray is opened and, if not, correct the guide copyir.com 3 copyir.com Check that the drive from the motor reaches the eject guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF bundle discharge unit sensor and DF main PWB (YC22)(4000-sheet finisher) DF bundle discharge unit sensor and DF main PWB (YC20)(1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF eject release motor copyir.com
DF bundle discharge unit sensor: 1 copyir.com Execute Finisher - Bundle Eject HP of U241 finisher switch check copyir.com 2 copyir.com Check that the sensor and its mounting board are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF bundle discharge unit sensor and DF main PWB (YC22)(4000-sheet finisher) DF bundle discharge unit sensor and DF main PWB (YC20)(1000-sheet finisher) 4 copyir.com Replace the DF bundle discharge unit sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8110 DF shift motor 1 error
(4000-sheet finisher) DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven copyir.com DF shift motor 1 [front]: 1 copyir.com Execute U240 Motor - Sort Test to check the finisher operation copyir.com 2 copyir.com Manipulate the front shift guide back and forth to check that it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the front shift guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift motor 1 and DF main PWB (YC14) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF shift motor 1
DF shift sensor 1 [front]: 1 copyir.com Execute U241 Finisher - Shift Front HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift sensor 1 and DF main PWB (YC23) 4 copyir.com Replace the DF shift sensor 1 copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8120 DF shift motor 2 error
(4000-sheet finisher) DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven copyir.com DF shift motor 2 [rear]: 1 copyir.com Execute U240 Motor - Sort Test to check the finisher operation copyir.com 2 copyir.com Manipulate the rear shift guide back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the rear shift guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift motor 2 and DF main PWB (YC14) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF shift motor 2 copyir.com
DF shift set sensor 2 [rear]: 1 copyir.com Execute U241 Finisher - Shift Trail HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift sensor 2 and DF main PWB (YC23) 4 copyir.com Replace the DF shift set sensor2 copyir.com
DF main PWB: Replace the DF main PWB
8130 DF shift release motor error
(4000-sheet finisher) When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com DF shift release motor: 1 copyir.com Check that cancelling the maintenance mode after executing U240 Motor - Sort for the finisher operation check lets the rear and forth cursors return to the home position copyir.com 2 copyir.com Manipulate the shift guide back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the shift guide front and rear copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift release motor and DF main PWB (YC23) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF shift release motor copyir.com
DF shift release sensor: 1 copyir.com Execute U241 Finisher - Shift Unlock HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF shift release sensor and DF main PWB (YC23) 4 copyir.com Replace the DF shift release sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com DF tray motor: 1 copyir.com Execute U240 Motor - Tray to check the finisher operation copyir.com 2 copyir.com Manipulate the main tray up and down to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the main tray copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray motor and DF Main PWB(YC16) (4000-sheet finisher) DF tray motor and DF Main PWB(YC14) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF tray motor copyir.com
DF tray sensor 1 DF tray upper surface sensor: 1 copyir.com Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray sensor 1 and DF Main PWB(YC22) (4000-sheet finisher) DF tray upper surface sensor and DF Main PWB(YC21,YC13) (4000-sheet finisher) DF tray sensor 1 and DF main PWB (YC20) (1000-sheet finisher) DF tray upper surface sensor and DF main PWB (YC18) (1000-sheet finisher) 4 copyir.com Replace the DF tray sensor 1 or DF tray upper surface sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s copyir.com DF tray motor: 1 copyir.com Execute U240 Motor - Tray to check the finisher operation copyir.com 2 copyir.com Manipulate the main tray up and down to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the main tray copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray motor and DF main PWB (YC16) (4000-sheet finisher) DF tray motor and DF main PWB (YC14) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF tray motor copyir.com
DF tray sensor 1 DF tray upper surface sensor: 1 copyir.com Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray sensor 1 and DF main PWB (YC22) (4000-sheet finisher) DF tray upper surface sensor and DF main PWB (YC21,YC13) (4000-sheet finisher) DF tray sensor 1 and DF main PWB (YC20) (1000-sheet finisher) DF tray upper surface sensor and DF main PWB (YC18) (1000-sheet finisher) 4 copyir.com Replace the DF tray sensor 1 or DF tray upper surface sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com DF tray motor: 1 copyir.com Execute U240 Motor - Tray to check the finisher operation copyir.com 2 copyir.com Manipulate the main tray up and down to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the main tray copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray motor and DF main PWB (YC16) (4000-sheet finisher) DF tray motor and DF main PWB (YC14) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF tray motor copyir.com
DF tray sensor 4: 1 copyir.com Execute U241 Finisher - Tray Middle to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF tray sensor 4 and DF main PWB (YC23) (4000-sheet finisher) DF tray sensor 4 and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com Replace the DF tray sensor 4 copyir.com
DF main PWB: Replace the DF main PWB
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com DF side registration motor 1: 1 copyir.com Execute U240 Motor - Width Test to check the finisher operation copyir.com 2 copyir.com Manipulate the front side registration guide to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the front side registration guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration motor 1 and DF main PWB (YC15) (4000-sheet finisher) DF side registration motor 1 and DF main PWB (YC11) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF side registration motor 1 copyir.com
DF side registration sensor 1: 1 copyir.com Execute U241 Finisher - Width Front to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration sensor 1 copyir.com and DF main PWB (YC22) (4000-sheet finisher) DF side registration sensor 1 copyir.com and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com Replace the DF side registration sensor 1 copyir.com
DF main PWB: Replace the DF main PWB
8180 DF side registration motor 1 error 2
JAM6810 ( jam in front of width alignment) is detected twice copyir.com DF side registration motor 1: 1 copyir.com Execute U240 Motor - Width Test to check the finisher operation copyir.com 2 copyir.com Manipulate the front side registration guide back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the front side registration guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration motor 1 and DF main PWB (YC15) (4000-sheet finisher) DF side registration motor 1 and DF main PWB (YC11) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF side registration motor 1 copyir.com
DF side registration sensor 1: 1 copyir.com Execute U241 Finisher - Width Front to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration sensor 1 copyir.com and DF main PWB (YC22) (4000-sheet finisher) DF side registration sensor 1 copyir.com and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the DF side registration sensor 1 copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com DF side registration motor 2: 1 copyir.com Execute U240 Motor - Width Test to check the finisher operation copyir.com 2 copyir.com Manipulate the rear side registration guide back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the rear side registration guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration motor 2 and DF main PWB (YC15) (4000-sheet finisher) DF side registration motor 2 and DF main PWB (YC11) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF side registration motor 2 copyir.com
DF side registration sensor 2: 1 copyir.com Execute U241 Finisher - Width tail HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration sensor 2 and DF main PWB (YC22) (4000-sheet finisher) DF side registration sensor 2 and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com Replace the DF side registration sensor 2 copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 ( jam in rear of width alignment) is detected twice copyir.com DF side registration motor 2: 1 copyir.com Execute U240 Motor - Width Test to check the finisher operation copyir.com 2 copyir.com Manipulate the rear side registration guide back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the rear side registration guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration motor 2 and DF main PWB (YC15) (4000-sheet finisher) DF side registration motor 2 and DF main PWB (YC11) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF side registration motor 2 copyir.com
DF side registration sensor 2: 1 copyir.com Execute U241 Finisher - Width tail HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF side registration sensor 2 and DF main PWB (YC22) (4000-sheet finisher) DF side registration sensor 2 and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com Replace the DF side registration sensor 2 copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com DF slide motor: 1 copyir.com Execute U240 Motor - Staple Move to check the finisher operation copyir.com 2 copyir.com Manipulate the staple unit back and forth to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the staple unit copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF slide motor and DF main PWB (YC12) (4000-sheet finisher) DF slide motor and DF main PWB (YC10) (1000-sheet finisher) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DF slide motor copyir.com
DF staple sensor: 1 copyir.com Execute U241 Finisher - Width Staple HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF staple sensor and DF main PWB (YC22) (4000-sheet finisher) DF staple sensor and DF main PWB (YC20) (1000-sheet finisher) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the DF staple sensor copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8230 DF staple motor error 1
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven copyir.com) DF staple motor: 1 copyir.com Remove the staple unit and check that stapling is possible without a jam copyir.com 2 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Staple unit and DF main PWB (YC17) (4000-sheet finisher) Staple unit and DF main PWB (YC11) (1000-sheet finisher) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the staple unit copyir.com
DF staple sensor: Replace the staple unit copyir.com
DF main PWB: Replace the DF main PWB
8240 DF staple motor error 2
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven copyir.com) DF staple motor: 1 copyir.com Remove the staple unit and check that stapling is possible without a jam copyir.com 2 copyir.com Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in copyir.com Staple unit and DF main PWB (YC17) (4000-sheet finisher) Staple unit and DF main PWB (YC11) (1000-sheet finisher) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the staple unit copyir.com
DF main PWB: Replace the DF main PWB
8300 Center-folding unit communication error
(4000-sheet finisher) Communication with the center- folding unit is not possible copyir.com CF unit set switch: 1 copyir.com Execute U241 Booklet - Set to check the finisher switch copyir.com 2 copyir.com Check that the switch and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF main PWB (YC7) and DF main PWB (YC9) 4 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the CF unit set switch copyir.com
CF main PWB: Replace the CF main PWB copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8310 CF side registration motor 2 error
(4000-sheet finisher) When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com CF side registration motor 2: 1 copyir.com Execute Motor - Width Test of U240 finisher operation check copyir.com 2 copyir.com Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth copyir.com 3 copyir.com Check that the drive from the motor reaches the side registration upper guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF side registration motor 2 and CF main PWB (YC10) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF side registration motor copyir.com
CF side registration sensor 2: 1 copyir.com Execute U241 Booklet - Width Up HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF side registration sensor 2 and CF main PWB (YC20) 4 copyir.com Replace the CF side registration sensor 2 copyir.com
CF main PWB: Replace the CF main PWB
8320 CF adjustment motor error
(4000-sheet finisher) When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.coma CF adjustment motor1,2: 1 copyir.com Execute U240 Motor - Bundle Up / Down to check the finisher operation copyir.com 2 copyir.com Manipulate the fold moving belt up and down to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the fold moving belt copyir.com (Check if the belt is bent copyir.com) 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF adjustment motor 1,2 and CF main PWB (YC10) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF adjustment motor1,2 copyir.com
CF adjustment sensor1,2: 1 copyir.com Execute U241 Booklet - bundle Up / Down HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF adjustment sensor 1,2 and CF main PWB (YC20) 4 copyir.com Replace the CF adjustment sensor1,2 copyir.com
CF main PWB: Replace the CF main PWB copyir.com
8330 CF blade motor error
(4000-sheet finisher) When initial operation, CF blade sensor does not turn on within 1500 ms copyir.com CF blade motor: 1 copyir.com Execute U240 Booklet - Blade to check the finisher operation copyir.com 2 copyir.com Manipulate the fold blade up and down to check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the fold blade copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF blade motor and CF main PWB (YC15) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF blade motor copyir.com
CF blade sensor: 1 copyir.com Execute U241 Booklet - Blade HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF blade sensor and CF main PWB (YC20) 4 copyir.com Replace the CF blade sensor copyir.com
CF main PWB: Replace the CF main PWB copyir.com
8340 CF staple motor error 1
(4000-sheet finisher) Staple JAM (center-folding unit) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven copyir.com) CF staple motor: 1 copyir.com Execute U240 Booklet - Staple to check the finisher operation copyir.com 2 copyir.com Manipulate the staple up and down check it is smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the staple unit copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF staple unit and CF main PWB (YC13) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF staple motor copyir.com
CF staple sensor: Replace the CF staple unit copyir.com
CF main PWB: Replace the CF main PWB copyir.com
8350 CF side registration motor 1 error
(4000-sheet finisher) When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com CF side registration motor 1: 1 copyir.com Execute U240 Booklet - Width Test to check the finisher operation copyir.com 2 copyir.com Manipulate the side registration lower guide back and forth to check it can smoothly operable copyir.com 3 copyir.com Check that the drive from the motor reaches the side registration lower guide copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF side registration motor 1 and CF main PWB (YC10) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF side registration motor 1 copyir.com
CF side registration sensor 1: 1 copyir.com Execute U241 Booklet - Width Down HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF side registration sensor 1 and CF main PWB (YC20) 4 copyir.com Replace the CF side registration sensor 1 copyir.com
CF main PWB Replace the CF main PWB copyir.com
8360 CF main motor error
(4000-sheet finisher) During driving the motor, the lock signal is detected for 1 s continuously copyir.com CF main motor: 1 copyir.com Execute U240 Booklet - Folding to check the finisher operation copyir.com 2 copyir.com Manipulate the conveying roller to check it can smoothly rotate copyir.com 3 copyir.com Check that the drive from the motor reaches the conveying roller copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF main motor and CF main PWB (YC16) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the CF main motor copyir.com
CF main PWB: Replace the CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Punch slide motor: 1 copyir.com Execute U240 Booklet - Punch Move to check the finisher operation copyir.com 2 copyir.com Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move copyir.com 3 copyir.com Check that the drive from the motor reaches punch area copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch slide motor and Punch PWB (YC3) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the punch slide motor copyir.com
Punch slide sensor: 1 copyir.com Execute U241 Punch - Punch HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch slide sensor and Punch PWB (YC6) 4 copyir.com Replace the punch slide sensor copyir.com
Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7) (4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8) (1000-sheet finisher) 2 copyir.com Replace the punch PWB copyir.com
DF main PWB: Replace the DF main PWB
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move Punch slide motor: 1 copyir.com Execute U240 Booklet - Punch Move to check the finisher operation copyir.com 2 copyir.com Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move copyir.com 3 copyir.com Check that the drive from the motor reaches punch part copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch slide motor and Punch PWB (YC3) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the punch slide motor copyir.com
Punch paper edge sensor 1,2: 1 copyir.com Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4 copyir.com Replace the punch paper edge sensor 1,2 copyir.com
Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7) (4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8) (1000-sheet finisher) 2 copyir.com Replace the Punch PWB copyir.com
DF main PWB: Replace the DF main PWB
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Punch PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Punch PWB (YC1) and DF main PWB (YC7) (4000-sheet finisher) Punch PWB (YC1) and DF main PWB (YC8) (1000-sheet finisher) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Punch PWB copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8500 Mailbox communication error
(4000-sheet finisher) Communication failed to be established after the mailbox was hooked up copyir.com MB main PWB: 1 copyir.com Turn the main power switch off and after 5 seconds, turn it on copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MB main PWB (YC3) and DF main PWB (YC6) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the MB main PWB copyir.com
DF main PWB: Replace the DF main PWB copyir.com
8510 MB conveying motor error 1
(4000-sheet finisher) When initial operation, MB home position sensor does not turn on within 5 s copyir.com MB conveying motor: 1 copyir.com If the transfer roller won’t rotate smoothly, repair its mechanism copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MB conveying motor and MB main PWB (YC5) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the MB conveying motor copyir.com
MB home position sensor: 1 copyir.com Execute U241 Mail Box - Motor HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MB home position sensor and MB main PWB (YC2) 4 copyir.com Replace the MB home position sensor copyir.com
MB main PWB: Replace the MB main PWB
8520 MB conveying motor error 2
(4000-sheet finisher) When standby operation, MB home position sensor does not turn off within 1 s copyir.com MB conveying motor: 1 copyir.com Execute Mail Box - Conv of U240 finisher operation check copyir.com 2 copyir.com Manipulate the conveying roller of the mailbox to check it can smoothly rotate copyir.com 3 copyir.com Check that the drive from the motor reaches the conveying roller copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MB conveying motor and MB main PWB (YC5) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the MB conveying motor copyir.com
MB home position sensor: 1 copyir.com Execute U241 Mail Box - Motor HP to check the finisher switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com MB home position sensor and MB main PWB (YC2) 4 copyir.com Replace the MB home position sensor copyir.com
MB main PWB: Replace the MB main PWB copyir.com
8800 Document finisher main program error
Document finisher main program error at power up copyir.com DF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF main PWB (YC4) and Engine PWB (YC18) (4000-sheet finisher) DF main PWB (YC7) and Engine PWB (YC18) (1000-sheet finisher) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the DF main PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com DF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DF main PWB (YC4) and Engine PWB (YC18) (4000-sheet finisher) DF main PWB (YC7) and Engine PWB (YC18) (1000-sheet finisher) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the DF main PWB copyir.com
8930 Center-folding unit backup error
(4000-sheet finisher) Read and write data does not match 3 times in succession copyir.com CF main PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CF main PWB (YC7) and DF main PWB (YC9) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Install the EEPROM properly copyir.com 4 copyir.com Replace the CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com DP main PWB: 1 copyir.com Check that the versions of the main unit firmware and the DP firmware are identical copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the DP main PWB copyir.com
ISC PWB: Replace the ISC PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com U206 setting: Set maintenance mode U206 to off when a coin vender is not installed copyir.com
Coin vender control PWB: 1 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com Coin vender control PWB and Engine PWB (YC23) 2 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 3 copyir.com Replace the Coin vender control PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse copyir.com (Three recovery times copyir.com) The above has been detected 5 times copyir.com * : The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transpoting copyir.com The accumulated number must be cleared at completion of a normal rise copyir.com The default threshold is 5 copyir.com DP lift motor: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Execute U243 Lift Motor to check the DP motor operation copyir.com 3 copyir.com Check that the original document lift guide can move upwards copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP lift motor and DP MAIN PWB (YC5) 5 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 6 copyir.com Replace the DP lift motor copyir.com
DP lift sensor 1: 1 copyir.com Execute U244 LIFT L-Limit to check DP switch copyir.com 2 copyir.com Check that the sensor and its mounting bracket are correctly positioned copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP lift sensor 1 and DP Main PWB (YC4) 4 copyir.com Replace the DP lift sensor 1 copyir.com
DP Main PWB: Replace the DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse copyir.com (Three recovery times copyir.com) The above has been detected 5 times copyir.com DP lift motor: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Execute U243 Lift Motor to check the DP motor operation copyir.com 3 copyir.com Check that the original document lift guide can move downwards copyir.com 4 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP lift motor and DP main PWB (YC5) If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 5 copyir.com Replace the DP lift motor copyir.com
DP lift sensor 2: 1 copyir.com Execute U244 LIFT L-Limit to check DP switch copyir.com 2 copyir.com Confirm that the DP lift sensor 2 has been firmly fitted copyir.com 3 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP lift sensor 2 and DP main PWB (YC2) 4 copyir.com Replace the DP lift sensor2 copyir.com
DP main PWB: Replace the DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com DP main PWB: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Confirm that the EEPROM has been properly installed copyir.com 3 copyir.com Replace the DP main PWB copyir.com
Device damage of EEPROM: Contact the Service Support copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com DP SHD PWB: 1 copyir.com Execute U906 Separating Operation Release copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com DP SHD PWB (YC1) and DP main PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the DP SHD PWB copyir.com
9080 LED fault detection
A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex copyir.com DP CIS: 1 copyir.com Execute CIS automatic original document alignment by U411 copyir.com 2 copyir.com Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in copyir.com CIS and DP SHD PWB (YC2) DP SHD PWB (YC1) and DP main PWB (YC10) 3 copyir.com If the wiring is disconnected, shorted or grounded, replace the wiring copyir.com 4 copyir.com Replace the CIS and execute U411 copyir.com
DP SHD PWB: Replace the DP SHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Coin vender control PWB: Replace the coin mec copyir.com
9110 Coin vender rejector error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector: 1 copyir.com Check that the rejector is firmly installed and, if not, install firmly copyir.com 2 copyir.com Replace the rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube: Check visually and remedy copyir.com
Contact in the connector: Check the connection of the empty change sensor copyir.com
Change empty sensor: Replace the coin mec copyir.com
Coin vender control PWB: Replace the coin mec copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube: Check visually and remedy copyir.com
Contact in the connector: Check the connection of the empty change sensor copyir.com
Change empty sensor Replace the coin mec copyir.com
Coin vender control PWB: Replace the coin mec copyir.com
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube: Check visually and remedy copyir.com
Contact in the connector: Check the connection of the empty change sensor copyir.com
Change empty sensor: Replace the coin mec copyir.com
Coin vender control PWB: Replace the coin mec copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough Change tube: Check no exchange jam is observed at the outlet and, if necessary, repair it copyir.com
Contact in the connector: Check the connection of the empty change sensor copyir.com
Change empty sensor: Replace the coin mec copyir.com
Coin vender control PWB: Replace the coin mec copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Pay-out motor: Replace the coin mec copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Pay-out area: Check no exchange jam is observed at the outlet and, if necessary, repair it copyir.com
Pay-out motor Replace the coin mec copyir.com
Pay-out sensor: Replace the coin mec copyir.com
9500 ISC PWB error A Main PWB, ISC PWB: 1 copyir.com Reinsert the connector if its connection is loose copyir.com Main PWB (YC25) and ISC PWB (YC4) 2 copyir.com Replace the main PWB copyir.com 3 copyir.com Replace the ISC PWB 4 copyir.com Contact the Service Support copyir.com
9510 ISC PWB error B Main PWB, DP SHD PWB: 1 copyir.com Reinsert the connector if its connection is loose copyir.com DP relay PWB (YC2) and DP SHD PWB (YC3) 2 copyir.com Replace the main PWB copyir.com 3 copyir.com Replace the DP SHD PWB copyir.com 4 copyir.com Contact the Service Support copyir.com
9520 ISC PWB error C Main PWB, ISC PWB: 1 copyir.com Reinsert the connector if it its connection is loose copyir.com Main PWB (YC25) and ISC PWB (YC4) 2 copyir.com Replace the main PWB copyir.com 3 copyir.com Replace the ISC main PWB 4 copyir.com Contact the Service Support copyir.com
9940 Confidential document guard uninstalled error
The confidential document guard PWB is removed while the confidential document guard PWB is valid copyir.com Confidential document guard PWB: 1 copyir.com Check that the confidential document guard PWB is firmly installed and, if not, install firmly copyir.com 2 copyir.com Replace the confidential document guard PW copyir.com
9950 Confidential document guard PWB error
FPGA configuration error CPU version information error This is caused when the PWB of a double-side scanning DP is connected, the confidential guard PWB is inserted, and the harness is not correctly connected copyir.com Confidential document guard PWB: 1 copyir.com Replace the confidential document guard PW copyir.com 2 copyir.com Replace the main PWB copyir.com
F000 Communication error between main PWB and operation PWB Main PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Check that the wirings and connetors between the main circuit PWB and the operation circuit PWB and between the main circuit PWB and the HDD are normal copyir.com Main PWB (YC12,YC17,YC30) and Operation PWB (YC1,YC2,YC3) 3 copyir.com Check that the DDR memories in the main circuit PWB are well conducted and, if not, replace copyir.com 4 copyir.com Execute U024 to initialize (FULL) the HDD copyir.com 5 copyir.com Execute U021 to initialize memory copyir.com 6 copyir.com Replace the Main PWB copyir.com 7 copyir.com Copy the log File saved in the HDD by U964 in USB memory and contact the service support copyir.com
Operation PWB: Replace the operation PWB copyir.com
F010 Main PWB checksum error Main PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com If not corrected, replace the main PWB copyir.com
F040 Communication error between Main PWB and Print engine Main PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Repair or replace the wire from the engine PWB, that may be grounded copyir.com (Check short-circuit between 5V and 3 copyir.com3V copyir.com) 3 copyir.com Check that the FCC wire connecting between the main PWB (YC3) and the engine PWB (YC46) is normal and, if necessary, re-insert copyir.comOr, replace the FCC wire copyir.com 4 copyir.com If not corrected, replace the main PWB copyir.com
Engine PWB: 1 copyir.com Check the engine software and upgrade to the latest, if necessary copyir.com 2 copyir.com Replace the engine PWB copyir.com
HDD: Replace the HDD copyir.com
F041 Communication error between Main PWB and Scanner engine Main PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Check that the wires between the main PWB and the ISC PWB are normal copyir.com 3 copyir.com If not corrected, replace the main PWB copyir.comI
SC PWB: Replace the ISC PWB copyir.com
F050 Print engine ROM checksum error Engine software: Install the latest engine software copyir.com
Engine PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Confirm that the EEPROM has been properly installed copyir.com 3 copyir.com If not corrected, Replace the engine PWB copyir.com
F051 Scanner engine ROM checksum error Scanner software: Install the latest scanner software copyir.com
ISC PWB: 1 copyir.com Turn the main power swtch off and after 5 seconds, then turn power on copyir.com 2 copyir.com Confirm that the EEPROM has been properly installed copyir.com 3 copyir.com If not corrected, Replace the ISC PWB copyir.com
F278 Power supply in drive system error The main power switch was turned off before the power switch is pressed copyir.com Shutdown due to a power failure: Turn the main power swtch off and after 5 seconds, then turn power on copyir.com (Before turning power off, verify that the power key has been pressed and the power indicator has gone off, then switch the main power switch copyir.com)
کیو سرا میتا Kyocera-Mita TASKalfa 5550ci
نوشته شده توسط ایراندوست بهزاد0010 P MOTOR 1 Color PC drum motor malfunction
• The color PC drum motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the color PC drum motor is being rotated copyir.com 1 Check the M2 connector for proper connection and correct as necessary copyir.com 2 Check M2 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M2 operation check MFPB PJ14MFPB-3 to 7 C-5 copyir.com 5 Change M2 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
0017 P MOTOR 2 Intermediate transport motor malfunction
• The intermediate transport motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the intermediate transport motor is being rotated copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check M3 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 5 Change M3 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
0018 D MOTOR 2 Developing motor /K malfunction
• The developing motor /K does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the developing motor /K is being rotated copyir.com 1 Check the M5 connector for proper connection and correct as necessary copyir.com 2 Check M5 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M5 operation check MFPB PJ33MFPB-3, 5 to 7 C-6 copyir.com 5 Change M5 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
001B D MOTOR 1 Developing motor / Y,M,C malfunction
• The developing motor /Y,M,C does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the developing motor /Y,M,C is being rotated copyir.com 1 Check the M1 connector for proper connection and correct as necessary copyir.com 2 Check the MFPB connector for proper connection and correct as necessary copyir.com 3 M1 operation check MFPB PJ8MFPB-3, 5 to 7 C-7 copyir.com 4 Change driving unit copyir.com 5 Change MFPB copyir.com 6 Change DCPU copyir.com
0046 FUSER FAN Fusing fan motor malfunction
• The fusing fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the fusing fan motor is being rotated copyir.com 1 Check the FM2 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM2 operation check MFPB PJ21MFPB-1 (ON) MFPB PJ21MFPB-3 (LOCK) C-9 copyir.com 4 Change FM2 copyir.com 5 Change MFPB copyir.com
004C OZONE FAN Ozone ventilation fan motor malfunction
• The ozone ventilation fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the ozone ventilation fan motor is being rotated copyir.com 1 Check the FM3 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM3 operation check MFPB PJ6MFPB-5 (ON) MFPB PJ21MFPB-7 (LOCK) J-6 copyir.com 4 Change FM3 copyir.com 5 Change MFPB copyir.com
004E POWER FAN DC power supply fan motor malfunction
• The DC power supply fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the DC power supply fan motor is being rotated copyir.com 1 Check the FM1 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM1 operation check MFPB PJ9MFPB-1 (ON) MFPB PJ9MFPB-3 (LOCK) C-2 copyir.com 4 Change FM1 copyir.com 5 Change MFPB copyir.com
0060 FUSER MOTOR Fusing motor malfunction
• The fusing motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the fusing motor is being rotated copyir.com 1 Check the M4 connector for proper connection and correct as necessary copyir.com 2 Check the fusing unit driving mechanism for possible overload and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M4 operation check MFPB PJ19MFPB-3, 5 to 7 C-9 copyir.com 5 Change M4 copyir.com 6 Change MFPB copyir.com
0094 XFER DETACH 2 2nd image transfer pressure / retraction failure
• The retraction position sensor /2 is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started copyir.com • The retraction position sensor /2 is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check the CL5 connector for proper connection and correct as necessary copyir.com 3 Check M3 for proper drive coupling and correct as necessary copyir.com 4 Check CL5 for proper drive coupling and correct as necessary copyir.com 5 Check the MFPB connector for proper connection and correct as necessary copyir.com 6 PS10 sensor check MFPB PJ10MFPB-6 (ON) J-7 copyir.com 7 CL5 operation check MFPB PJ10MFPB-8 (ON) J-7 copyir.com 8 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 9 Change M3 copyir.com 10 Change CL5 copyir.com 11 Change MFPB copyir.com
0096 XFER DETACH 1 1st image transfer pressure / retraction failure
• The retraction position sensor /1 is not activated (retracted position) within a given period of time after the intermediate transport motor has started rotating copyir.com • The retraction position sensor /1 is not deactivated (pressed position) within a given period of time after the intermediate transport motor has started rotating copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check the CL4 connector for proper connection and correct as necessary copyir.com 3 Check M3 for proper drive coupling and correct as necessary copyir.com 4 Check CL4 for proper drive coupling and correct as necessary copyir.com 5 Check the MFPB connector for proper connection and correct as necessary copyir.com 6 PS9 sensor check MFPB PJ7MFPB-13 (ON) C-2 copyir.com 7 CL4 operation check MFPB PJ7MFPB-10 (ON) C-1 copyir.com 8 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 9 Change M3 copyir.com 10 Change CL4 copyir.com 11 Change MFPB copyir.com
0300 POLYGON MOTOR Polygon motor malfunction
• The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated copyir.com 1 Check the cable and connector for proper connection and correct as necessary copyir.com 2 Change PH unit copyir.com 3 Change MFPB copyir.com
0310 LASER ERROR Laser malfunction
• The SOS signal is not detected within a given period of time after the output of the laser has been started copyir.com 1 Check the cable and connector for proper connection and correct as necessary copyir.com 2 Change PH unit copyir.com 3 Change MFPB copyir.com
0500 FUSER ERROR Heating roller warm-up failure
• The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0501 FUSER ERROR Fusing pressure roller warm-up failure
• The thermistor /2 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0510 FUSER ERROR Abnormally low heating roller temperature
• The temperature detected by the thermistor /1 remains lower than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0511 FUSER ERROR Abnormally low fusing pressure roller temperature
• The temperature detected by the thermistor /2 remains lower than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0520 FUSER ERROR Abnormally high heating roller temperature
• The temperature detected by the thermistor /1 remains higher than the specified value for a given period of time or longer copyir.com • The heater lamp remains ON for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0521 FUSER ERROR Abnormally high fusing pressure roller temperature
• The temperature detected by the thermistor /2 remains higher than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0B30 FINISHER ERROR Finisher aligning plate drive malfunction
0B47 FINISHER ERROR Finisher media holding drive malfunction
0B48 FINISHER ERROR Finisher exit roller pressure/retraction malfunction
0B4A FINISHER ERROR Finisher aligning belt pressure/retraction malfunction
0B4C FINISHER ERROR Finisher media ejector motor malfunction
0BA0 FINISHER ERROR Finisher tray up/down motor ascent/descent drive malfunction
0BE1 FINISHER ERROR Finisher fan motor malfunction
0F52 TE SENSOR Y Toner level sensor /Y malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F53 TE SENSOR M Toner level sensor /M malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F54 TE SENSOR C Toner level sensor /C malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F55 TE SENSOR K Toner level sensor /K malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
133B FINISHERE COMMUNICATION Finisher communication error
• A communication error occurs between the main body and the finisher copyir.com 1 Reboot the main body copyir.com 2 Change FSCB copyir.com 3 Change MFPB copyir.com
13C0 ENGINE H/W ERROR MFP board malfunction
• A communication error occurs in MFP board (MFPB) copyir.com 1 Reboot the main body copyir.com 2 Change MFPB copyir.com
13E2 FLASH WRITE Flash ROM write error
• Flash ROM writing is found faulty during a check copyir.com 1 Check the MFPB for proper connection and correct as necessary copyir.com 2 Change PRCB copyir.com 3 Change MFPB copyir.com
13E3 FLASH DEVICE Flash ROM device fault
• An erase error occurs during erasing of data in flash ROM copyir.com 1 Check the MFPB for proper connection and correct as necessary copyir.com 2 Change PRCB copyir.com 3 Change MFPB copyir.com
3C00 EEPROM1 Trouble related to security
3C10 EEPROM2 Trouble related to security
3FFB FINISHER ROM Finisher flash ROM error
• An error occurs with flash ROM of the optional staple finisher copyir.com 1 Check the FSCB for proper connection and correct as necessary copyir.com 2 Change FSCB copyir.com
C002 RAM ERROR RAM error at startup (standard memory)
• RAM error at standard memory is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check connection state of the standard/ expanded memory and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change the standard/expanded memory copyir.com 5 Change PRCB copyir.com
C003 RAM ERROR RAM error at startup (expanded memory)
• RAM error at expanded memory is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check connection state of the standard/ expanded memory and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change the standard/expanded memory copyir.com 5 Change PRCB copyir.com
C013 H/W ADDRESS MAC address error at startup
• Invalid MAC address is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
C015 BOOT ROM Boot ROM error at startup
• Boot ROM error is detected during printer startup copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
C025 CONTROLLER ROM Controller ROM error (Configuration information error)
• Lead error of destination setting file is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C026 CONTROLLER ROM Controller ROM error (Access error)
• Flash ROM access error is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C027 CONTROLLER ROM Controller ROM error (Data error)
• Final check sum error is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C050 HDD ERROR HDD access error
• When correct access to the hard disk kit is failed during access copyir.com 1 Reboot the main body copyir.com 2 Check the HDD connector for proper connection and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change HDD copyir.com 5 Change PRCB copyir.com
C051 HDD DISK FULL HDD full error
• Range for user space is full during access to the hard disk kit copyir.com 1 Reboot the main body copyir.com 2 Delete the job hold in PROOF/PRINT MENU to increase the available range for user space copyir.com 3 Check the HDD connector for proper connection and correct as necessary copyir.com 4 Format HDD with SYS DEFAULT MENU/ HDD FORMAT copyir.com 5 Change HDD copyir.com
C052 CARD ERROR Compact flash access error
• When correct access to the compact flash card is failed during access copyir.com 1 Reboot the main body copyir.com 2 Check the compact flash for proper connection and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change compact flash copyir.com 5 Change PRCB copyir.com
C053 CARD FULL Compact flash full error
• Range for user space is full during access to the compact flash card copyir.com 1 Reboot the main body copyir.com 2 Delete the job hold in “PROOF/PRINT MENU” to increase the available range for user space copyir.com 3 Check the compact flash for proper connection and correct as necessary copyir.com 4 Format compact flash with SYS DEFAULT MENU/CARD FORMAT copyir.com 5 Change compact flash copyir.com
C060 UPDATE ERROR Firmware update error
• Firmware update fails to complete correctly during update copyir.com 1 Reboot the main body copyir.com 2 Check the cable that has been used for update of the firmware for proper connection and correct as necessary copyir.com 3 Check the firmware update file and if the file is not the correct one, update the firmware again copyir.com 4 Check the firmware update procedure and if the procedure is not correct, update the firmware again copyir.com 5 Update the firmware again copyir.com 6 Check the PRCB connector for proper connection and correct as necessary copyir.com 7 Change PRCB copyir.com
C071 H/W CONFIG ERROR Hardware configuration error
• An error occurs with hardware configuration (video clock etc copyir.com) copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
FFFF I/F COMM ERROR Interface Communication error
• Correct communication is failed when receiving/ sending the command between MFPB and PRCB copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 Change MFPB copyir.com 5 Change PRCB copyir.com
کیو سرا میتا Konica-Minolta Magicolor 5570
نوشته شده توسط ایراندوست بهزاد0010 P MOTOR 1 Color PC drum motor malfunction
• The color PC drum motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the color PC drum motor is being rotated copyir.com 1 Check the M2 connector for proper connection and correct as necessary copyir.com 2 Check M2 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M2 operation check MFPB PJ14MFPB-3 to 7 C-5 copyir.com 5 Change M2 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
0017 P MOTOR 2 Intermediate transport motor malfunction
• The intermediate transport motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the intermediate transport motor is being rotated copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check M3 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 5 Change M3 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
0018 D MOTOR 2 Developing motor /K malfunction
• The developing motor /K does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the developing motor /K is being rotated copyir.com 1 Check the M5 connector for proper connection and correct as necessary copyir.com 2 Check M5 for proper drive coupling and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M5 operation check MFPB PJ33MFPB-3, 5 to 7 C-6 copyir.com 5 Change M5 copyir.com 6 Change MFPB copyir.com 7 Change DCPU copyir.com
001B D MOTOR 1 Developing motor / Y,M,C malfunction
• The developing motor /Y,M,C does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the developing motor /Y,M,C is being rotated copyir.com 1 Check the M1 connector for proper connection and correct as necessary copyir.com 2 Check the MFPB connector for proper connection and correct as necessary copyir.com 3 M1 operation check MFPB PJ8MFPB-3, 5 to 7 C-7 copyir.com 4 Change driving unit copyir.com 5 Change MFPB copyir.com 6 Change DCPU copyir.com
0046 FUSER FAN Fusing fan motor malfunction
• The fusing fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the fusing fan motor is being rotated copyir.com 1 Check the FM2 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM2 operation check MFPB PJ21MFPB-1 (ON) MFPB PJ21MFPB-3 (LOCK) C-9 copyir.com 4 Change FM2 copyir.com 5 Change MFPB copyir.com
004C OZONE FAN Ozone ventilation fan motor malfunction
• The ozone ventilation fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the ozone ventilation fan motor is being rotated copyir.com 1 Check the FM3 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM3 operation check MFPB PJ6MFPB-5 (ON) MFPB PJ21MFPB-7 (LOCK) J-6 copyir.com 4 Change FM3 copyir.com 5 Change MFPB copyir.com
004E POWER FAN DC power supply fan motor malfunction
• The DC power supply fan motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the DC power supply fan motor is being rotated copyir.com 1 Check the FM1 connector for proper connection and correct as necessary copyir.com 2 Check the fan for possible overload and correct as necessary copyir.com 3 FM1 operation check MFPB PJ9MFPB-1 (ON) MFPB PJ9MFPB-3 (LOCK) C-2 copyir.com 4 Change FM1 copyir.com 5 Change MFPB copyir.com
0060 FUSER MOTOR Fusing motor malfunction
• The fusing motor does not rotate evenly even after the lapse of a given period of time while it is being started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the fusing motor is being rotated copyir.com 1 Check the M4 connector for proper connection and correct as necessary copyir.com 2 Check the fusing unit driving mechanism for possible overload and correct as necessary copyir.com 3 Check the MFPB connector for proper connection and correct as necessary copyir.com 4 M4 operation check MFPB PJ19MFPB-3, 5 to 7 C-9 copyir.com 5 Change M4 copyir.com 6 Change MFPB copyir.com
0094 XFER DETACH 2 2nd image transfer pressure / retraction failure
• The retraction position sensor /2 is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started copyir.com • The retraction position sensor /2 is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check the CL5 connector for proper connection and correct as necessary copyir.com 3 Check M3 for proper drive coupling and correct as necessary copyir.com 4 Check CL5 for proper drive coupling and correct as necessary copyir.com 5 Check the MFPB connector for proper connection and correct as necessary copyir.com 6 PS10 sensor check MFPB PJ10MFPB-6 (ON) J-7 copyir.com 7 CL5 operation check MFPB PJ10MFPB-8 (ON) J-7 copyir.com 8 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 9 Change M3 copyir.com 10 Change CL5 copyir.com 11 Change MFPB copyir.com
0096 XFER DETACH 1 1st image transfer pressure / retraction failure
• The retraction position sensor /1 is not activated (retracted position) within a given period of time after the intermediate transport motor has started rotating copyir.com • The retraction position sensor /1 is not deactivated (pressed position) within a given period of time after the intermediate transport motor has started rotating copyir.com 1 Check the M3 connector for proper connection and correct as necessary copyir.com 2 Check the CL4 connector for proper connection and correct as necessary copyir.com 3 Check M3 for proper drive coupling and correct as necessary copyir.com 4 Check CL4 for proper drive coupling and correct as necessary copyir.com 5 Check the MFPB connector for proper connection and correct as necessary copyir.com 6 PS9 sensor check MFPB PJ7MFPB-13 (ON) C-2 copyir.com 7 CL4 operation check MFPB PJ7MFPB-10 (ON) C-1 copyir.com 8 M3 operation check MFPB PJ27MFPB-3 to 7 C-5 copyir.com 9 Change M3 copyir.com 10 Change CL4 copyir.com 11 Change MFPB copyir.com
0300 POLYGON MOTOR Polygon motor malfunction
• The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started copyir.com • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated copyir.com 1 Check the cable and connector for proper connection and correct as necessary copyir.com 2 Change PH unit copyir.com 3 Change MFPB copyir.com
0310 LASER ERROR Laser malfunction
• The SOS signal is not detected within a given period of time after the output of the laser has been started copyir.com 1 Check the cable and connector for proper connection and correct as necessary copyir.com 2 Change PH unit copyir.com 3 Change MFPB copyir.com
0500 FUSER ERROR Heating roller warm-up failure
• The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0501 FUSER ERROR Fusing pressure roller warm-up failure
• The thermistor /2 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0510 FUSER ERROR Abnormally low heating roller temperature
• The temperature detected by the thermistor /1 remains lower than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0511 FUSER ERROR Abnormally low fusing pressure roller temperature
• The temperature detected by the thermistor /2 remains lower than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0520 FUSER ERROR Abnormally high heating roller temperature
• The temperature detected by the thermistor /1 remains higher than the specified value for a given period of time or longer copyir.com • The heater lamp remains ON for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0521 FUSER ERROR Abnormally high fusing pressure roller temperature
• The temperature detected by the thermistor /2 remains higher than the specified value for a given period of time or longer copyir.com 1 Check the fusing unit for correct installation (whether it is secured in position) copyir.com 2 Check the fusing unit, DCPU, and MFPB for proper connection and correct as necessary copyir.com 3 Change fusing unit copyir.com 4 Change MFPB copyir.com 5 Change DCPU copyir.com
0B30 FINISHER ERROR Finisher aligning plate drive malfunction
0B47 FINISHER ERROR Finisher media holding drive malfunction
0B48 FINISHER ERROR Finisher exit roller pressure/retraction malfunction
0B4A FINISHER ERROR Finisher aligning belt pressure/retraction malfunction
0B4C FINISHER ERROR Finisher media ejector motor malfunction
0BA0 FINISHER ERROR Finisher tray up/down motor ascent/descent drive malfunction
0BE1 FINISHER ERROR Finisher fan motor malfunction
0F52 TE SENSOR Y Toner level sensor /Y malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F53 TE SENSOR M Toner level sensor /M malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F54 TE SENSOR C Toner level sensor /C malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
0F55 TE SENSOR K Toner level sensor /K malfunction
• An error occurs on the toner level sensor board (TLSB) copyir.com 1 Check the TLSB and MFPB for proper connection and correct as necessary copyir.com 2 Change TLSB copyir.com 3 Change MFPB copyir.com
133B FINISHERE COMMUNICATION Finisher communication error
• A communication error occurs between the main body and the finisher copyir.com 1 Reboot the main body copyir.com 2 Change FSCB copyir.com 3 Change MFPB copyir.com
13C0 ENGINE H/W ERROR MFP board malfunction
• A communication error occurs in MFP board (MFPB) copyir.com 1 Reboot the main body copyir.com 2 Change MFPB copyir.com
13E2 FLASH WRITE Flash ROM write error
• Flash ROM writing is found faulty during a check copyir.com 1 Check the MFPB for proper connection and correct as necessary copyir.com 2 Change PRCB copyir.com 3 Change MFPB copyir.com
13E3 FLASH DEVICE Flash ROM device fault
• An erase error occurs during erasing of data in flash ROM copyir.com 1 Check the MFPB for proper connection and correct as necessary copyir.com 2 Change PRCB copyir.com 3 Change MFPB copyir.com
3C00 EEPROM1 Trouble related to security
3C10 EEPROM2 Trouble related to security
3FFB FINISHER ROM Finisher flash ROM error
• An error occurs with flash ROM of the optional staple finisher copyir.com 1 Check the FSCB for proper connection and correct as necessary copyir.com 2 Change FSCB copyir.com
C002 RAM ERROR RAM error at startup (standard memory)
• RAM error at standard memory is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check connection state of the standard/ expanded memory and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change the standard/expanded memory copyir.com 5 Change PRCB copyir.com
C003 RAM ERROR RAM error at startup (expanded memory)
• RAM error at expanded memory is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check connection state of the standard/ expanded memory and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change the standard/expanded memory copyir.com 5 Change PRCB copyir.com
C013 H/W ADDRESS MAC address error at startup
• Invalid MAC address is detected during printer start-up copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
C015 BOOT ROM Boot ROM error at startup
• Boot ROM error is detected during printer startup copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
C025 CONTROLLER ROM Controller ROM error (Configuration information error)
• Lead error of destination setting file is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C026 CONTROLLER ROM Controller ROM error (Access error)
• Flash ROM access error is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C027 CONTROLLER ROM Controller ROM error (Data error)
• Final check sum error is detected during the printer starting copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again copyir.com 4 Change PRCB copyir.com
C050 HDD ERROR HDD access error
• When correct access to the hard disk kit is failed during access copyir.com 1 Reboot the main body copyir.com 2 Check the HDD connector for proper connection and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change HDD copyir.com 5 Change PRCB copyir.com
C051 HDD DISK FULL HDD full error
• Range for user space is full during access to the hard disk kit copyir.com 1 Reboot the main body copyir.com 2 Delete the job hold in PROOF/PRINT MENU to increase the available range for user space copyir.com 3 Check the HDD connector for proper connection and correct as necessary copyir.com 4 Format HDD with SYS DEFAULT MENU/ HDD FORMAT copyir.com 5 Change HDD copyir.com
C052 CARD ERROR Compact flash access error
• When correct access to the compact flash card is failed during access copyir.com 1 Reboot the main body copyir.com 2 Check the compact flash for proper connection and correct as necessary copyir.com 3 Check the PRCB connector for proper connection and correct as necessary copyir.com 4 Change compact flash copyir.com 5 Change PRCB copyir.com
C053 CARD FULL Compact flash full error
• Range for user space is full during access to the compact flash card copyir.com 1 Reboot the main body copyir.com 2 Delete the job hold in “PROOF/PRINT MENU” to increase the available range for user space copyir.com 3 Check the compact flash for proper connection and correct as necessary copyir.com 4 Format compact flash with SYS DEFAULT MENU/CARD FORMAT copyir.com 5 Change compact flash copyir.com
C060 UPDATE ERROR Firmware update error
• Firmware update fails to complete correctly during update copyir.com 1 Reboot the main body copyir.com 2 Check the cable that has been used for update of the firmware for proper connection and correct as necessary copyir.com 3 Check the firmware update file and if the file is not the correct one, update the firmware again copyir.com 4 Check the firmware update procedure and if the procedure is not correct, update the firmware again copyir.com 5 Update the firmware again copyir.com 6 Check the PRCB connector for proper connection and correct as necessary copyir.com 7 Change PRCB copyir.com
C071 H/W CONFIG ERROR Hardware configuration error
• An error occurs with hardware configuration (video clock etc copyir.com) copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Change PRCB copyir.com
FFFF I/F COMM ERROR Interface Communication error
• Correct communication is failed when receiving/ sending the command between MFPB and PRCB copyir.com 1 Reboot the main body copyir.com 2 Check the PRCB connector for proper connection and correct as necessary copyir.com 3 Check the MFPB connector for proper connect