کیو سرا میتا Kyocera-Mita TASKalfa 4820w

کیو سرا میتا Kyocera-Mita TASKalfa 4820w

E-000    Fuser Temperature Rising Error
Fuser Temperature does not reach 50C within 120 seconds after turning on     copyir.com
E-001    Fuser Over Temperature Error
Fuser Temperature reaches over 230C     copyir.com
E-002    Fuser Low Temperature Error
1     copyir.com Fuser Temperature at the time of turning on was 50 to 100C, but it does not rise up to 120C within 150 seconds after that     copyir.com
2     copyir.com Fuser Temperature at the time of turning on was higher than 100C, but it does not rise up to the setting temperature within 330 seconds after that     copyir.com
E-003    Fuser Temperature Abnormal Fall Error
The difference of temperature between center and side of fuser becomes 50C or more     copyir.com
E-004    Fuser Temperature Abnormal Fall Error
The Lamp of fuser lights (Signal HEAT1 is “H”) to heat up the Fuser Roller in the ready condition, but even 1C of temperature rise can not be accomplished within 30 seconds     copyir.com
E-010    Main Motor Error
The Main Motor Output Detection Signal (MAINM_LD) continues to be “H” for 3 seconds or longer when the Main Motor is rotating     copyir.com
E-011    Fuser Motor Error
The Fuser Motor Output Detection Signal (HEATM_LD) continues to be “H” for 3 seconds or longer when the Fuser Motor is rotating     copyir.com
E-012    Developer Press Motor Error
The Developer Press Sensor Signal (PRESS_S) does not change to “L” within 30 seconds after turning on     copyir.com
E-020    Counter Error
The Counter Connection Detection Signal (COUNT_OPN) continues to be “L” for 1 second or longer after turning on     copyir.com
E-031    Image Corona Output Error
The Image Corona Output Detection Signal (IM_LD) continues to be “L” for 1 second or longer when the Image Corona is ON     copyir.com
E-032    Separation Corona Output Error
The Separation Corona Output Detection Signal (AC_LD) continues to be “L” for 1 second or longer when the Separation Corona is ON     copyir.com
E-033    Transfer Corona Output Error
The Transfer Corona Output Detection Signal (TR_LD) continues to be “L” for 1 second or longer when the Transfer Corona is ON     copyir.com
E-034    Bias Output Error
Bias Output Detection Signal (BIAS_LD) continues to be “L” for 1 second or longer when a specified bias is supplied to the corresponding Developer Unit components     copyir.com
E-040    Cutter Error
1     copyir.com The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “H” within 100 millisecond since the Cutter has started the operation     copyir.com
2     copyir.com The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “L” within 1 second since the Cutter has started the operation     copyir.com
E-050    FPGA Error
Initialization of FPGA is failed after turning on     copyir.com
E-070    Developer Unit Set Error
1     copyir.com The Connector J-253 is not connected     copyir.com
2     copyir.com The Switch (MS4) is “open” condition, which detects open/close of Engine Unit or Toner Hatch     copyir.com
E-080    Density Sensor Error
The default output of Density Sensor reaches less than 0     copyir.com1V or more than 1     copyir.com3V     copyir.com
E-081    Density Sensor Output Error
The gap between the default output and the standard output of Density Sensor reaches less than 2V     copyir.com