درایور فتوکپی ریکو MP 3353
1404-08-05
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
C0030 Fax control PWB system problem
Processing with the fax software was disabled due to a hardware or software problem copyir.com Defective fax control PWB copyir.com
C0060 Main PWB type mismatch error Defective PWB copyir.com
C0070 Abnormal detection of fax control PWB incompatibility
In the initial communication with the fax control PWB, any normal communication command is not transmitted copyir.com Defective fax software copyir.com
Defective fax control PWB copyir.com
C0100 Backup memory (EEPROM) device problem (Main PWB)
Reading from or writing to EEPROM cannot be performed copyir.com Defective main PWB copyir.com
Device damage of EEPROM copyir.com
C0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective main PWB copyir.com
C0150 Backup memory (EEPROM) device problem (Engine PWB)
Reading from or writing to EEPROM cannot be performed copyir.com Defective engine PWB copyir.com
Device damage of EEPROM copyir.com
C0160 Backup memory (EEPROM) data problem (Engine PWB)
Reading data from EEPROM is abnormal copyir.com Read and write data does not match 5 times continuously copyir.com Data damage of EEPROM copyir.com
C0170 Copy counts problem
A checksum error is detected in the main and engine backup memories for the copy counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
C0180 Machine number mismatch error
Machine number of main PWB and engine PWB does not match copyir.com Data damage of EEPROM copyir.com
C0620 FAX image DIMM problem
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
C0630 DMA problem
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
C0640 Hard disk drive problem
The hard disk cannot be accessed copyir.com Poor contact in the connector terminals copyir.com
Defective hard disk copyir.com
Defective main PWB copyir.com
C0650 FAX image DIMM check problem
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
DIMM of another machine is installed copyir.com
Defective main PWB copyir.com
C0800 Image processing problem
JAM05 is detected twice copyir.com Defective main PWB copyir.com
C0830 Fax control PWB flash program area checksum error
A checksum error occurred with the program of the fax control PWB copyir.com Defective fax software copyir.com
Defective fax control PWB copyir.com
C0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com Defective main PWB copyir.com
The battery is disconnected from the main PWB copyir.com
C0870 Fax control PWB to main PWB high capacity data transfer problem
High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the fax control PWB copyir.com Defective fax control PWB copyir.com
C1010 Lift motor 1 error
After cassette 1 is inserted, lift switch 1 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Poor contact in the connector terminals copyir.com
Broken gears or couplings of lift motor 1 copyir.com
Defective lift motor 1 copyir.com
Poor contact in the connector terminals copyir.com
Defective lift switch 1 copyir.com
Defective engine PWB copyir.com
C1020 Lift motor 2 error
After cassette 2 is inserted, lift switch 2 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Poor contact in the connector terminals copyir.com
Broken gears or couplings of lift motor 2 copyir.com
Defective lift motor 2 copyir.com
Poor contact in the connector terminals copyir.com
Defective lift switch 2 copyir.com
Defective engine PWB copyir.com
C1030 PF lift motor 1 error (optional paper feeder)
After cassette 3 is inserted, PF lift switch 1 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Poor contact in the connector terminals copyir.com
Broken gears or couplings of PF lift motor 1 copyir.com
Defective PF lift motor 1 copyir.com
Defective PF lift switch 1 copyir.com
C1040 PF lift motor 2 error (optional paper feeder)
After cassette 4 is inserted, PF lift switch 2 does not turn on within 12 s copyir.com This error is detected four times successively copyir.com Poor contact in the connector terminals
Broken gears or couplings of PF lift motor 2 copyir.com
Defective PF lift motor 2 copyir.com
Defective PF lift switch 2 copyir.com
C1100 PF lift motor 1 error (optional 3000sheet paper feeder)
A motor over-current signal is detected continuously for 1 s or longer copyir.com Poor contact in the connector terminals copyir.com
PF lift motor 1 does not rotate correctly (the motor is overloaded) copyir.com
C1110 PF lift motor 2 error (optional 3000sheet paper feeder)
A motor over-current signal is detected continuously for 1 s or longer copyir.com Poor contact in the connector terminals copyir.com
PF lift motor 2 does not rotate correctly (the motor is overloaded) copyir.com
C1120 PF left lift position problem (optional 3000-sheet paper feeder)
Level switch 1 does not turn on within 30 s of PF lift motor 1 turning on copyir.com Poor contact in the connector terminals copyir.com
Defective level switch 1 copyir.com
Defective PF lift motor 1 copyir.com
The PF left lift does not rise properly copyir.com
C1130 PF right lift position problem (optional 3000-sheet paper feeder)
Level switch 2 does not turn on within 30 s of PF lift motor 2 turning on copyir.com Poor contact in the connector terminals copyir.com
Defective level switch 2 copyir.com
Defective PF lift motor 2 copyir.com
The PF right lift does not rise properly copyir.com
C1800 Paper feeder communication error (optional paper feeder)
A communication error from paper feeder is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C1900 Paper feeder EEPROM error (optional paper feeder)
When writing the data, the write data and the read data is not continuously in agreement three times copyir.com Poor contact in the connector terminals copyir.com
Defective engine PWB copyir.com
Defective paper feeder copyir.com
C2000 Drive motor problem
Stable OFF is detected for 1 s continuously after drive motor stability copyir.com The drive motor is not stabilized in 6 s since the motor is activated copyir.com Poor contact in the connector terminals copyir.com
Defective drive transmission system copyir.com
Defective drive motor copyir.com
Defective engine PWB copyir.com
C2250 Main charger cleaning motor error
A locking error has been detected three times in a row during a reciprocating cleaning motion copyir.com Poor contact in the connector terminals copyir.com
Defective drive transmission system copyir.com
Defective main charger cleaning motor copyir.com
Defective engine PWB copyir.com
C2500 Paper feed motor error
Stable OFF is detected for 1 s continuously after paper feed motor stability copyir.com The paper feed motor is not stabilized in 6 s since the motor is activated copyir.com Poor contact in the connector terminals copyir.com
Defective drive transmission system copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
C2600 PF paper conveying/drive motor error (optional 3000-sheet paper feeder/ paper feeder)
The lock signal of the motor is detected above 450 ms copyir.com Poor contact in the connector terminals copyir.com
Defective drive transmission system copyir.com
Defective PF paper conveying/drive motor copyir.com
Defective PWB copyir.com
C3100 Scanner carriage problem
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Poor contact in the connector terminals copyir.com
Defective home position switch copyir.com
Defective scanner motor copyir.com
The mirror frame, exposure lamp, or scanner wire is defective copyir.com
Defective PWB copyir.com
C3200 Exposure lamp problem
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s copyir.com Poor contact in the connector terminals copyir.com
Defective exposure lamp copyir.com
Incorrect shading position copyir.com
Defective PWB copyir.com
C3210 CIS lamp problem
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Poor contact in the connector terminals copyir.com
Defective DP driver PWB copyir.com
Defective DP inverter PWB copyir.com
Defective CIS copyir.com
C3300 Optical system (AGC) problem
After AGC, correct input is not obtained at CCD copyir.com Poor contact in the connector terminals copyir.com
Defective exposure lamp or inverter PWB copyir.com
Defective PWB copyir.com
C3310 CIS AGC problem
After AGC, correct input is not obtained at CIS copyir.com Defective DP driver PWB copyir.com
CIS output problem copyir.com
Defective DP inverter PWB copyir.com
C3500 Communication error between scanner and SHD
An error code is detected copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C3900 Backup memory read/write problem (ISC PWB)
Read and write data does not match copyir.com Defective backup RAM or PWB copyir.com
C3910 Backup memory data problem (ISC PWB)
Data in the specified area of the backup memory does not match the specified values copyir.com Defective backup RAM or PWB copyir.com
C4000 Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on copyir.com Poor contact in the connector terminals copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
C4010 Polygon motor steady-state problem
Stable OFF is detected for 20 s continuously after polygon motor stability copyir.com Poor contact in the connector terminals copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
C4100 BD initialization problem
5 consecutive BD errors were detected during an 800 ms interval after the polygon motor stabilized copyir.com Poor contact in the connector terminals copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
C6000 Fuser heater break
Fuser thermistor 1 detected less than 70°C/158°F for 10 s during warm-up and ready in copyir.com During warm-up, the temperature at the fuser unit thermistor 1 does not rise by 1°C/1 copyir.com8°F continuously for 5 s copyir.com Fuser thermistor 2 detected less than 40°C/104°F for 10 s during warm-up and ready in copyir.com During warm-up, the temperature at the fuser unit thermistor 2 does not rise by 1°C/1 copyir.com8°F continuously for 5 s copyir.com Defective fuser heater 1 or 2 copyir.com
Installation defectiveness on fuser thermistor 1 copyir.com
Defective fuser thermostat copyir.com
Defective PWB copyir.com
C6020 Abnormally high fuser thermistor temperature
Fuser thermistor 1 or 2 is detected 250°C/482°F or more for 40 ms copyir.com Installation defectiveness on fuser thermistor 1 or 2 copyir.com
Defective fuser thermistor unit 1 or 2 copyir.com
Defective engine PWB copyir.com
C6030 Fuser thermistor break error
The fuser thermistor break signal is detected continuously for 1 s copyir.com Installation defectiveness on fuser thermistor 1 or 2 copyir.com
Defective fuser thermistor 1 or 2 copyir.com
Defective engine PWB copyir.com
C6040 Fuser thermistor 1 detection error
Fuser thermistor 1 detected an abnormal value for at least 1 s copyir.com Installation defectiveness on fuser thermistor 1 copyir.com
Defective fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
C6050 Abnormally low fuser thermistor temperature
Fuser thermistor 1 is detected 80°C/ 176°F less than 1 s continuously during copying copyir.com Defective fuser heater 1 or 2 copyir.com
Installation defectiveness on fuser thermistor 1 copyir.com
Defective PWB copyir.com
C6400 Zero-cross signal error
While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s copyir.com Defective PWB
C6410 Fuser unit connector insertion problem
Absence of the fuser unit is detected copyir.com Fuser unit connector inserted incorrectly copyir.com
Defective fuser unit connector copyir.com
C7300 Toner container problem
Toner level is not detected when toner empty is detected copyir.com Poor contact in the connector terminals copyir.com
Defective toner container sensor copyir.com
C7400 Developing unit connector insertion problem Absence of the developing unit is detected copyir.com Developing unit connector inserted incorrectly copyir.com
Defective developing unit connector copyir.com
C7410 Drum unit connector insertion problem
Absence of the drum unit is detected copyir.com Drum unit connector inserted incorrectly copyir.com
Defective drum unit connector copyir.com
C7800 Broken external thermistor wire
The thermistor output value is 4 copyir.com5 V or more copyir.com Poor contact in the connector terminals copyir.com
Defective humidity sensor copyir.com
C7900 Drum EEPROM error
Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com
Defective drum unit copyir.com
C7910 Developing unit EEPROM error
Reading from or writing to EEPROM cannot be performed copyir.com Poor contact in the connector terminals copyir.com
Defective developing unit copyir.com
C8020 Punch motor problem (optional 3000sheet document finisher)
The error signal of the punch motor is detected for more than 500 ms while the punch motor is operating copyir.com Poor contact in the connector terminals copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
C8030 Tray upper limit detection problem (optional document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected copyir.com The tray upper limit sensor, paper surface sensor 1/2 connector makes poor contact copyir.com
Defective tray upper limit sensor, paper surface sensor 1/2 copyir.com
Defective finisher main PWB copyir.com
C8040 Belt problem (optional document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on copyir.com The belt sensor, belt solenoid connector makes poor contact copyir.com
Defective belt sensor copyir.com
Defective belt solenoid copyir.com
Defective finisher main PWB copyir.com
C8050 Paper conveying belt motor 1 problem (optional 3000-sheet document finisher)
Paper conveying belt home position sensor 1 does not turn off within 1 copyir.com5 s copyir.com Paper conveying belt home position sensor 1 does not turn on within 2 copyir.com5 s copyir.com Jam 88 is indicated copyir.com Poor contact in the connector terminals copyir.com
Defective paper conveying belt home position sensor 1 copyir.com
Defective paper conveying belt motor 1 copyir.com
Defective PWB copyir.com
C8060 Paper conveying belt motor 2 problem (optional 3000-sheet document finisher)
Paper conveying belt home position sensor 2 does not turn off within 1 copyir.com5 s copyir.com Paper conveying belt home position sensor 2 does not turn on within 1 copyir.com5 s copyir.com Poor contact in the connector terminals copyir.com
Defective paper conveying belt home position sensor 2 copyir.com
Defective paper conveying belt motor 2 copyir.com
Defective PWB copyir.com
C8070 Inner tray communication error (optional 3000-sheet document finisher)
Communication with the inner tray is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C8140 Main tray problem (optional 3000sheet document finisher)
The main tray is not detected by the main tray upper limit detection sensor or the main tray paper upper surface detection sensor within 20 s since the tray has started ascending copyir.com The main tray upper limit detection sensor or the main tray paper upper surface detection
Tray elevation motor problem (optional document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated copyir.com Poor contact in the connector terminals copyir.com
Defective main tray motor copyir.com
Defective main tray
Defective finisher main PWB copyir.com
The tray elevation motor connector makes poor contact copyir.com
The tray elevation motor malfunctions copyir.com
The tray lower limit sensor, paper surface sensor 1/2 connector makes poor contact copyir.com
Defective tray lower limit sensor, paper surface sensor 1/2 copyir.com
Defective finisher main PWB copyir.com
C8170 Side registration motor 1 problem (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed copyir.com Jam 88 is indicated copyir.com
Finisher front side registration motor problem (optional built-in finisher) When the front-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the front-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com Poor contact in the connector terminals copyir.com
Defective side registration motor 1 copyir.com
Defective PWB copyir.com
The front side registration motor connector makes poor contact copyir.com
Defective front side registration motor copyir.com
The front side registration home position sensor connector makes poor contact copyir.com
Defective front side registration home position sensor copyir.com
Defective finisher control PWB copyir.com
C8180 Side registration motor 2 problem (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 s passed copyir.com Jam 88 is indicated copyir.com
Finisher rear side registration motor problem (optional built-in finisher) When the rear-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the rear-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com Poor contact in the connector terminals copyir.com
Defective side registration motor 2 copyir.com
Defective PWB copyir.com
The rear side registration motor connector makes poor contact copyir.com
Defective rear side registration motor copyir.com
The rear side registration home position sensor connector makes poor contact copyir.com
Defective rear side registration home position sensor copyir.com
Defective finisher control PWB copyir.com
C8190 Finisher trailing edge registration motor problem (optional built-in finisher)
When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses copyir.com When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s copyir.com The trailing edge registration motor connector makes poor contact copyir.com
Defective trailing edge registration motor copyir.com
The trailing edge registration home position sensor connector makes poor contact copyir.com
Defective trailing edge registration home position sensor copyir.com
Defective finisher control PWB copyir.com
C8210 Stapler moving motor 1 error (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 1 copyir.com5 s passed copyir.com
Stapler problem (optional document finisher) Jam 82 is indicated copyir.com
Finisher stapler problem (optional built-in finisher) The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation copyir.com During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation copyir.com Poor contact in the connector terminals copyir.com
Defective stapler moving motor 1 copyir.com
Defective finisher main PWB copyir.com
The stapler connector makes poor contact copyir.com
The stapler is blocked with a staple copyir.com
The stapler is broken copyir.com
Defective finisher main PWB copyir.com
The stapler connector makes poor contact copyir.com
The stapler is blocked with a staple copyir.com
The stapler is broken copyir.com
Defective finisher control PWB copyir.com
C8220 Stapler moving motor 2 error (optional 3000-sheet document finisher)
When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3 copyir.com5 s passed copyir.com Poor contact in the connector terminals copyir.com
Defective stapler moving motor 2 copyir.com
Defective staple relay PWB copyir.com
Defective finisher main PWB copyir.com
C8230 Stapler motor problem (optional 3000sheet document finisher)
Jam 82 is indicated copyir.com Poor contact in the connector terminals copyir.com
Defective stapler motor copyir.com
Defective staple relay PWB copyir.com
Defective finisher main PWB copyir.com
C8300 Center-folding unit communication error (optional center-folding unit of 3000-sheet document finisher)
Communication with the center-folding unit is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold set switch copyir.com
Defective centerfold main PWB copyir.com
Defective finisher main PWB copyir.com
C8310 Centerfold side registration motor 2 problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1 s passed copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold side registration motor 2 copyir.com
Defective PWB copyir.com
C8320 Centerfold paper conveying belt motor problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 2 copyir.com5 s passed copyir.com
Adjustment motor 2 problem (optional document finisher) The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold paper conveying belt motor 1/2 copyir.com
Defective PWB copyir.com
The adjustment sensor 2, adjustment motor 2 connector makes poor contact copyir.com
Defective adjustment sensor 2 copyir.com
Defective adjustment motor 2 copyir.com
Defective finisher main PWB copyir.com
C8330 Blade motor problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1 copyir.com5 s passed copyir.com
Adjustment motor 1 problem (optional document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on copyir.com Poor contact in the connector terminals copyir.com
Defective blade motor copyir.com
Defective PWB copyir.com
The adjustment sensor 1, adjustment motor 1 connector makes poor contact copyir.com
Defective adjustment sensor 1 copyir.com
Defective adjustment motor 1 copyir.com
Defective finisher main PWB copyir.com
C8340 Centerfold staple motor problem (optional center-folding unit of 3000sheet document finisher)
Jam 89 is indicated copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold staple motor copyir.com
Defective PWB copyir.com
C8350 Centerfold side registration motor 1 problem (optional center-folding unit of 3000-sheet document finisher)
The home position is not detected when initial operation even if 1 s passed copyir.com
Roller motor problem (optional document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold side registration motor 1 copyir.com
Defective PWB copyir.com
The roller sensor, roller motor connector makes poor contact copyir.com
Defective roller sensor copyir.com
Defective roller motor copyir.com
Defective finisher main PWB copyir.com
C8360 Centerfold main motor problem (optional center-folding unit of 3000sheet document finisher)
The motor lock signal is detected above 1 s during driving the centerfold main motor copyir.com
Slide motor problem (optional document finisher) The slide sensor does not turn on/off within specified time of the slide motor turning on copyir.com Poor contact in the connector terminals copyir.com
Defective centerfold main motor copyir.com
Defective PWB copyir.com
The slide sensor, slide motor connector makes poor contact copyir.com
Defective slide sensor copyir.com
Defective slide motor copyir.com
Defective finisher main PWB copyir.com
C8440 Sensor adjusting problem (optional document finisher)
The sensor cannot be adjusted within the specified range copyir.com The paper entry sensor connector makes poor contact copyir.com
Defective paper entry sensor copyir.com
The optical path of the paper entry sensor is blocked by foreign matter copyir.com
Defective finisher main PWB copyir.com
C8460 EEPROM problem (optional document finisher)
Reading from or writing to EEPROM cannot be performed copyir.com Defective EEPROM or finisher main PWB copyir.com
C8500 Mailbox communication error (optional mailbox of 3000-sheet document finisher)
Communication with the mailbox is not possible although the connection is detected copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C8510 Mailbox drive motor problem (optional mailbox of 3000-sheet document finisher)
The motor lock signal is detected above 500 ms during driving the mailbox drive motor copyir.com Poor contact in the connector terminals copyir.com
Defective mailbox drive motor copyir.com
Defective PWB copyir.com
C8800 Document finisher communication error (optional 3000-sheet document finisher)
A communication error from document finisher is detected 10 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C8900 Finisher backup problem (optional 3000-sheet document finisher)
Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com
EEPROM installed incorrectly copyir.com
Defective finisher main PWB copyir.com
C8910 Punch backup problem (optional of 3000-sheet document finisher)
Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com
Defective punch PWB copyir.com
C8920 Mailbox backup problem (optional mailbox of 3000-sheet document finisher)
Read and write data does not match copyir.com Poor contact in the connector terminals copyir.com
Defective mailbox main PWB copyir.com
C8930 Center-folding backup problem (optional center-folding unit of 3000sheet document finisher)
Read and write data does not match 3 times in succession copyir.com Poor contact in the connector terminals copyir.com
EEPROM installed incorrectly copyir.com
Defective centerfold main PWB copyir.com
C9000 DP communication problem (optional DP)
A communication error is detected copyir.com Poor contact in the connector terminals copyir.com
Defective PWB copyir.com
C9040 DP lift motor going up error (optional DP) The tray upper limit switch does not turn on within 2 s of DP lift motor turning on copyir.com Loose connection of the DP lift motor connector copyir.com
Malfunction of the DP lift motor copyir.com
Loose connection of the tray upper limit switch connector copyir.com
Malfunction of the tray upper limit switch copyir.com
Defective DP driver PWB copyir.com
C9050 DP lift motor going down error (optional DP)
The tray lower limit switch does not turn on within 2 s of DP lift motor turning on copyir.com Loose connection of the DP lift motor connector copyir.com
Malfunction of the DP lift motor copyir.com
Loose connection of the tray lower limit switch connector copyir.com
Malfunction of the tray lower limit switch copyir.com
Defective DP driver PWB copyir.com
C9060 DP EEPROM error (optional DP)
Read and write data does not match copyir.com Data in the specified area of the backup memory does not match the specified values copyir.com Defective DP driver PWB copyir.com
Device damage of EEPROM copyir.com
C9070 Communication problem between DP and SHD (optional DP)
A communication error is detected copyir.com Loose connection of the SHD PWB copyir.com
Defective SHD PWB copyir.com
C9080 Communication problem between DP and CIS (optional DP)
A communication error is detected copyir.com Loose connection of CIS copyir.com
Defective CIS copyir.com
C9500, C9510, C9520 Contact the Service Administrative Division copyir.com
F000 Operation panel PWB communication error Defective main PWB copyir.com
Defective operation panel PWB copyir.com
F040 Engine PWB communication error Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Scanner PWB communication error Defective main PWB copyir.com
Defective ISM PWB copyir.com
F050 Engine ROM checksum error Defective engine PWB copyir.com
F090 Fax control PWB communication error Defective main PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.