کیو سرا میتا Kyocera-Mita TASKalfa 5500i

کیو سرا میتا Kyocera-Mita TASKalfa 5500i

0030    FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem     copyir.com    Defective FAX control PWB     copyir.com
0070    FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted     copyir.com    Defective FAX software     copyir.com
Defective FAX control PWB     copyir.com
0100    Backup memory device error    Defective flash memory     copyir.com
Defective main PWB     copyir.com
0120    MAC address data error
For data in which the MAC address is invalid     copyir.com    Defective flash memory
Defective engine PWB     copyir.com
0150    Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively     copyir.com Mismatch of reading data from 2 locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Improper installation EEPROM     copyir.com
Device damage of EEPROM     copyir.com
0160    Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal     copyir.com    Data damage of EEPROM     copyir.com
0170    Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters     copyir.com    Data damage of EEPROM     copyir.com
Defective PWB     copyir.com
0180    Machine number mismatch
Machine number of main and engine does not match     copyir.com    Data damage of EEPROM     copyir.com
0620    FAX image DIMM error
DIMM is not installed correctly     copyir.com DIMM cannot be accessed     copyir.com    DIMM installed incorrectly     copyir.com
Defective main PWB     copyir.com
0630    DMA error
DMA transmission of image data does not complete within the specified period of time     copyir.com    Poor contact in the connector terminals     copyir.com
Defective main PWB     copyir.com
0640    Hard disk error
The hard disk cannot be accessed     copyir.com    Defective hard disk     copyir.com
Defective main PWB     copyir.com
0650    FAX image DIMM check error
Improper DIMM is installed     copyir.com    DIMM installed incorrectly     copyir.com
Defective main PWB     copyir.com
0800    Image processing error
JAM010X is detected twice     copyir.com    Defective main PWB     copyir.com
0830    FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB     copyir.com    Defective FAX software     copyir.com
Defective FAX control PWB     copyir.com
0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed     copyir.com    The battery is disconnected from the main PWB
Defective main PWB     copyir.com
0870    FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times    Improper installation FAX control PWB     copyir.com
Defective FAX control PWB or main PWB     copyir.com
0900    FAX software incompatible detection error
Incompatible FAX control PWB is installed     copyir.com    Defective FAX software     copyir.com
Defective FAX control PWB     copyir.com
0920    Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB     copyir.com    Defective FAX control PWB     copyir.com
0970    12 V power down detect Power is disconnected during sleeping     copyir.com    Defective power source PWB     copyir.com
0980    24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected     copyir.com    Defective power source PWB     copyir.com
1000    MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 1     copyir.com5 s     copyir.com    Defective MP plate elevation mechanism     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective MP lift motor     copyir.com
Defective engine PWB     copyir.com
1010    Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s     copyir.com
This error is detected 4 times successively     copyir.com The lock signal of the motor is detected continuously for 1 s     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective lift motor 1     copyir.com
Defective engine PWB     copyir.com
1020    Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 4 times successively     copyir.com The lock signal of the motor is detected continuously for 1 s     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective lift motor 2     copyir.com
Defective engine PWB     copyir.com
1030    PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF lift motor 1     copyir.com
Defective PF main PWB     copyir.com
1040    PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 5 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively     copyir.com However, the first 1 s after motor is turned on is excluded from detection     copyir.com    Defective bottom plate elevation mechanism in the cassette     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF lift motor 2     copyir.com
Defective PF main PWB     copyir.com
1100    PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s     copyir.com This error is detected 2 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively     copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF lift motor 1     copyir.com
Defective PF main PWB     copyir.com
1110    PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s     copyir.com This error is detected 2 times successively     copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 500 ms or more 2 times successively     copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF lift motor 2     copyir.com
Defective PF main PWB     copyir.com
1140    SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s     copyir.com The lock signal of the motor is detected continuously for 200 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective SD lift motor     copyir.com
Defective SD main PWB     copyir.com
1720    Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible     copyir.com    The paper feeder is installed with a device to which it is incompatible     copyir.com
1800    Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession     copyir.com    Improper installation paper feeder     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
Defective engine PWB     copyir.com
Defective PF main PWB     copyir.com
1900    Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession     copyir.com    Defective PF main PWB     copyir.com
Device damage of EEPROM     copyir.com
2101    Developer motor error
After developer motor is driven, the ready signal does not turn to L within 5 s     copyir.com After developer motor is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective developer motor     copyir.com
Defective engine PWB     copyir.com
2201    Drum motor steady-state error
After drum motor is stabilized, the ready signal is at the H level for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective drum motor     copyir.com
Defective engine PWB     copyir.com
2300    Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s     copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective fuser motor     copyir.com
Defective engine PWB     copyir.com
2500    Transfer motor error
After transfer motor is driven, the ready signal does not turn to L within 2 s     copyir.com After transfer motor is stabilized, the ready signal is at the H level for 1 s continuously    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective fuser motor     copyir.com
Defective engine PWB     copyir.com
2550    Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective paper feed motor     copyir.com
Defective engine PWB     copyir.com
2600    PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF paper feed motor     copyir.com
Defective PF main PWB     copyir.com
2610    PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective PF paper feed motor     copyir.com
Defective PF main PWB     copyir.com
2640    SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective SD paper feed motor     copyir.com
Defective SD main PWB     copyir.com
2810    Inner motor error Initialized when an error is constantly observed for 2 seconds after the inner motor is activated     copyir.com An error is constantly observed for 2     copyir.com5 seconds after rebooting     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective inner motor     copyir.com
Defective engine PWB     copyir.com
3100    Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective home position sensor     copyir.com
Defective scanner motor     copyir.com
Defective ISC PWB     copyir.com
Defective main PWB     copyir.com
3200    Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective LED lamp PWB     copyir.com
Defective ISC PWB     copyir.com
Defective main PWB     copyir.com
3210    CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CIS     copyir.com
Defective DPSHD PWB     copyir.com
Defective DP relay PWB     copyir.com
3300    Optical system (AGC) error
After AGC, correct input is not obtained at CCD     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective exposure lamp
Defective CCD PWB     copyir.com
Defective ISC PWB     copyir.com
Defective main PWB     copyir.com
3310    CIS AGC error After AGC, correct input is not obtained at CIS     copyir.com    Defective CIS     copyir.com
Defective DPSHD PWB     copyir.com
Defective DP relay PWB     copyir.com
3500    Communication error between scanner and ASIC
An error code is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective ISC PWB     copyir.com
Defective main PWB     copyir.com
3600    Scanner sequence error    Defective ISC PWB     copyir.com
3700    Scanner device error    CCD connector inserted incorrectly     copyir.com
3800    AFE error
When writing the data, read and write data does not match 3 times in succession     copyir.com    Defective ISC PWB     copyir.com
3900    Backup memory read/write error (ISC PWB)
Read and write data does not match     copyir.com    Defective backup memory or PWB     copyir.com
4001    Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 30 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
4011    Polygon motor steady-state error
After polygon motor is stabilized, the ready signal is at the H level for 15 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective polygon motor     copyir.com
Defective engine PWB     copyir.com
4101    BD initialization error
After polygon motor is driven, ASIC detects a BD error for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective PD PWB     copyir.com
Defective engine PWB     copyir.com
4201    BD steady-state error
The BD signal is not detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective PD PWB     copyir.com
Defective engine PWB     copyir.com
5101    Main high-voltage error
Abnormality of charger roller is detected when Vpp adjustment     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective high voltage PWB
Defective engine PWB     copyir.com
6000    Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up     copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 30 s in warming up after reached to 100° C/212 °F     copyir.com A temperature of less than 80°C/176 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 100°C/ 212 °F after warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Fuser thermostat triggered     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6020    Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Shorted fuser thermistor 1     copyir.com
Defective engine PWB     copyir.com
6030    Broken fuser thermistor 2 wire A temperature of less than 30°C/86°F was observed at the fuser thermistor 2 when the temperature at the fuser thermistor 1 is greater than 70°C/158°F during warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Broken fuser thermistor 1 wire     copyir.com
Fuser thermostat triggered     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6040    Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Broken fuser thermistor 1 wire     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6050    Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Defective fuser thermistor 1     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6200    Broken fuser edge heater wire
A temperature of less than 90°C/194 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 160°C/ 320 °F after warming up     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Fuser thermostat triggered     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6220    Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 250°C/482°F for 1 s     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Shorted fuser thermistor 2     copyir.com
Defective engine PWB     copyir.com
6230    Broken fuser thermistor 2 wire
Input from fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Deformed connector pin     copyir.com
Defective triac     copyir.com
Broken fuser thermistor 2 wire     copyir.com
Fuser thermostat triggered     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6250    Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s after warming up     copyir.com    Deformed connector pin     copyir.com
Defective triac     copyir.com
Defective fuser thermistor 2     copyir.com
Defective fuser heater     copyir.com
Defective engine PWB     copyir.com
6400    Zero-cross signal error
While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective fuser heater PWB     copyir.com
6900    Fuser front fan motor error
When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective fuser front fan motor     copyir.com
Defective engine PWB     copyir.com
6910    Fuser rear fan motor error
When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective fuser rear fan motor     copyir.com
Defective engine PWB     copyir.com
7001    Toner motor error
A state in which the lock signal is detected for 20 times has been detected 3 times during the toner motor is activated     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective toner motor     copyir.com
Defective engine PWB     copyir.com
7101    Toner sensor error
Sensor output value of 60 or less or 944 or more continued for 3 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective engine PWB     copyir.com
7200    Broken outer temperature sensor wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective outer temperature sensor     copyir.com
Defective engine PWB     copyir.com
7210    Short-circuited outer temperature sensor
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective outer temperature sensor     copyir.com
Defective engine PWB     copyir.com
7221    Broken LSU thermistor wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective LSU thermistor     copyir.com
Defective engine PWB     copyir.com
7231    Short-circuited LSU thermistor
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective LSU thermistor     copyir.com
Defective engine PWB     copyir.com
7241    Broken developer thermistor wire
The sensor input sampling is greater than 230     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective developer thermistor     copyir.com
Defective engine PWB     copyir.com
7251    Short-circuited developer thermistor
The sensor input sampling is less than 69     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective developer thermistor     copyir.com
Defective engine PWB     copyir.com
7301    Toner hopper motor error
When the toner hopper motor is driven, toner hopper sensor does not turn on within 200 ms     copyir.com This error is detected 15 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drive transmission system of motor     copyir.com
Defective toner hopper sensor     copyir.com
Defective toner hopper motor     copyir.com
Defective engine PWB     copyir.com
7401    Developer unit type mismatch error
Absence of the developer unit is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Different type of the developer unit is installed     copyir.com
7411    Drum unit type mismatch error
Absence of the drum unit is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Different type of the drum unit is installed     copyir.com
7460    Developer shutter error
Power is turned on while the developer shutter is locked     copyir.com    The developer shutter has been locked     copyir.com
Defective connector cable or poor contact in the connector     copyir.com
7601    ID sensor error
An abnormal value is detected in the input data to ID sensor     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective engine PWB     copyir.com
7602    ID sensor error
An abnormal value is detected in the input data to ID sensor     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective engine PWB     copyir.com
7800    Broken outer temperature sensor wire
The sensor input sampling is greater than 255     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective outer temperature sensor     copyir.com
Defective engine PWB     copyir.com
7810    Short-circuited outer temperature sensor
The sensor input sampling is less than 0     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective outer temperature sensor     copyir.com
Defective engine PWB     copyir.com
7901    Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective drum PWB     copyir.com
7911    Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively     copyir.com Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective developer unit     copyir.com
7941    Laser scanner unit EEPROM error
Mismatch of reading data from two locations occurs 8 times successively     copyir.com Mismatch between writing data and reading data occurs 8 times successively     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective APC PWB     copyir.com
8010    Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective punch home position sensor     copyir.com
Defective punch motor     copyir.com
Defective PWB     copyir.com
8020    Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective punch motor     copyir.com
Defective PWB     copyir.com
8030    Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective punch motor     copyir.com
Defective PWB     copyir.com
8090    DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF paddle sensor     copyir.com
Defective DF paddle motor     copyir.com
Defective DF main PWB     copyir.com
8100    DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF bundle discharge sensor     copyir.com
Defective DF eject release motor     copyir.com
Defective DF main PWB     copyir.com
8110    DF shift motor 1 error
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DF shift sensor 1     copyir.com
Defective DF shift motor 1
Defective DF main PWB     copyir.com
8120    DF shift motor 2 error
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DF shift sensor 2     copyir.com
Defective DF shift motor 2     copyir.com
Defective DF main PWB     copyir.com
8130    DF shift release motor error
When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DF shift release sensor     copyir.com
Defective DF shift release motor
Defective DF main PWB     copyir.com
8140    DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective sensor     copyir.com
Defective DF tray motor     copyir.com
Defective DF main PWB     copyir.com
8150    DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective sensor     copyir.com
Defective DF tray motor     copyir.com
Defective DF main PWB     copyir.com
8160    DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF tray sensor 3     copyir.com
Defective DF tray motor     copyir.com
Defective DF main PWB     copyir.com
8170    DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF side registration sensor 1     copyir.com
Defective DF side registration motor 1     copyir.com
Defective DF main PWB     copyir.com
8180    DF side registration motor 1 error 2
JAM6810 is detected twice     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)
Defective DF side registration sensor 1     copyir.com
Defective DF side registration motor 1     copyir.com
Defective DF main PWB     copyir.com
8190    DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF side registration sensor 2     copyir.com
Defective DF side registration motor 2     copyir.com
Defective DF main PWB     copyir.com
8200    DF side registration motor 2 error 2
JAM6910 is detected twice     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF side registration sensor 2     copyir.com
Defective DF side registration motor 2     copyir.com
Defective DF main PWB     copyir.com
8210    DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF staple sensor     copyir.com
Defective DF slide motor     copyir.com
Defective DF main PWB     copyir.com
8230    DF staple motor error 1
JAM7000 is detected twice     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF staple sensor
Defective DF staple motor     copyir.com
Defective DF main PWB     copyir.com
8240    DF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF staple motor
Defective DF main PWB     copyir.com
8250    DF tray motor error 4
The lock signal of the motor is detected continuously for 500 ms     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective DF tray motor     copyir.com
Defective DF main PWB     copyir.com
8300    Center-folding unit communication error
Communication with the center-folding unit is not possible     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF set sensor     copyir.com
Defective PWB     copyir.com
8310    CF side registration motor 2 error
When initial operation, CF side registration sensor 2 does not turn on within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF side registration sensor 2     copyir.com
Defective CF side registration motor 2     copyir.com
Defective CF main PWB     copyir.com
8320    CF adjustment motor error
When initial operation, CF adjustment sensor does not turn on within 2     copyir.com5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF adjustment sensor 1, 2     copyir.com
Defective CF adjustment motor 1, 2     copyir.com
Defective CF main PWB     copyir.com
8330    CF blade motor error
When initial operation, CF blade sensor does not turn on within 1     copyir.com5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF blade sensor     copyir.com
Defective CF blade motor     copyir.com
Defective CF main PWB     copyir.com
8340    CF staple motor error 1
JAM7600 is detected twice     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF staple sensor     copyir.com
Defective CF staple motor     copyir.com
Defective CF main PWB     copyir.com
8350    CF side registration motor 1 error
When initial operation, CF side registration sensor 1 does not turn on within 1 s    Defective connector cable or poor contact in the connector     copyir.com
Defective CF side registration sensor 1     copyir.com
Defective CF side registration motor 1     copyir.com
Defective CF main PWB     copyir.com
8360    CF main motor error
During driving the motor, lock signal is detected for 1 s continuously     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CF main motor     copyir.com
Defective CF main PWB     copyir.com
8370    CF staple motor error 2
The lock signal of the motor is detected continuously for 500 ms     copyir.com    Defective connector cable or poor contact in the connector
Defective CF staple motor     copyir.com
Defective CF main PWB
8410    Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective slide sensor     copyir.com
Defective punch slide motor
Defective PWB     copyir.com
8420    Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective punch slide motor     copyir.com
Defective PWB     copyir.com
8430    Punch unit communication error
Communication with the punch unit is not possible     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective PWB     copyir.com
8500    Mailbox communication error
Communication with the mailbox is not possible     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective PWB     copyir.com
8510    MB conveying motor error 1
When initial operation, MB home position sensor does not turn on within 5 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective MB home position sensor
Defective MB conveying motor     copyir.com
Defective MB main PWB     copyir.com
8520    MB conveying motor error 2
When standby operation, MB home position sensor does not turn off within 1 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective MB home position sensor     copyir.com
Defective MB conveying motor     copyir.com
Defective MB main PWB     copyir.com
8800    Document finisher communication error
Communication with the document finisher is not possible     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Defective PWB     copyir.com
8900    Document finisher backup error
Read and write data does not match 3 times in succession     copyir.com    Defective connector cable or poor contact in the connector (4000-sheet finisher)     copyir.com
Defective connector cable or poor contact in the connector (1000-sheet finisher)     copyir.com
Improper installation EEPROM     copyir.com
Defective DF main PWB     copyir.com
8930    Center-folding unit backup error
Read and write data does not match 3 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Improper installation EEPROM     copyir.com
Defective CF main PWB     copyir.com
9000    Document processor communication error
Communication with the document processor is not possible     copyir.com    Defective connector cable or poor contact in the connector
Defective PWB     copyir.com
9010    Coin vender communication error
A communication error from coin vender is detected 10 times in succession     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Data setup failure     copyir.com
Defective coin vender control PWB     copyir.com
Defective PWB     copyir.com
9040    DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DP lift sensor 1     copyir.com
Defective DP lift motor     copyir.com
Defective DP main PWB     copyir.com
9050    DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DP lift sensor 2     copyir.com
Defective DP lift motor     copyir.com
Defective DP main PWB     copyir.com
9060    DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively     copyir.com Mismatch between writing data and reading data occurs 3 times successively     copyir.com    Defective DP main PWB     copyir.com
Device damage of EEPROM     copyir.com
9070    Communication error between DP and SHD
A communication error is detected     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective DPSHD PWB     copyir.com
9080    LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less     copyir.com    Defective connector cable or poor contact in the connector     copyir.com
Defective CIS
Defective DPSHD PWB     copyir.com
9100    Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB     copyir.com    Defective coin vender control PWB     copyir.com
9110    Coin vender error
Communication error has been detected in connection with the coin mec and the rejector     copyir.com    Rejector installed incorrectly     copyir.com
Defective rejector     copyir.com
9120    Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough     copyir.com    Coin jam in the change tube
Poor contact in the connector     copyir.com
Defective change empty sensor     copyir.com
Defective coin vender control PWB     copyir.com
9130    Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough     copyir.com    Coin jam in the change tube
Poor contact in the connector     copyir.com
Defective change empty sensor     copyir.com
Defective coin vender control PWB     copyir.com
9140    Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough     copyir.com    Coin jam in the change tube
Poor contact in the connector     copyir.com
Defective change empty sensor     copyir.com
Defective coin vender control PWB     copyir.com
9150    Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough     copyir.com    Coin jam in the change tube
Poor contact in the connector     copyir.com
Defective change empty sensor     copyir.com
Defective coin vender control PWB     copyir.com
9160    Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active     copyir.com    Defective pay-out motor     copyir.com
9170    Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active     copyir.com    Change jam at the pay-out     copyir.com
Defective pay-out motor     copyir.com
Defective pay-out sensor     copyir.com
9500, 9510, 9520, 9530, 9540, 9550    Contact the Service Administrative Division     copyir.com
F000    Communication error between main PWB and operation PWB    Defective main PWB     copyir.com
Defective operation PWB     copyir.com
F010    Main PWB checksum error    Defective main PWB     copyir.com
F040    Communication error between main PWB and print engine    Defective main PWB     copyir.com
Defective engine PWB     copyir.com
F041    Communication error between main PWB and scanner engine    Defective main PWB     copyir.com
Defective ISC PWB     copyir.com
F050    Print engine ROM checksum error    Defective engine PWB     copyir.com
F051    Scanner engine ROM checksum error    Defective ISC PWB     copyir.com
F278    Power supply in drive system error    Main power switch was turned off without using the power key, or a power failure has occurred     copyir.com