درایور فتوکپی ریکو MP 3353
1404-08-05
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
0030 FAX control PWB system error
Processing with the fax software was disabled due to a software problem copyir.com FAX control PWB
0060 Engine PWB mismatch
Unmatching engine and engine sub boards copyir.com Defective engine subboard copyir.com Engine PWB
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com FAX control PWB (The FAX PWB installed will not be the one designed for the machine) copyir.com
0100 Backup memory device error EEPROM(main PWB)
0120 MAC address data error
For data in which the MAC address is invalid copyir.com EEPROM(main PWB)
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com EEPROM (engine PWB)
0160 Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal copyir.com EEPROM
0170 Billing counting error
The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter copyir.com EEPROM copyir.com Main PWB copyir.com Engine PWB
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0350 Panel PWB communication error (electronic volume I2C communication error) NACK is received during I2C communication – retried 5 times – rebooting command sent – retried 5 times If NACK is still received copyir.com Operation PWB copyir.com Main PWB
0620 FAX image DIMM error 1 copyir.com
The Fax image DIMM has not been installed copyir.com 2 copyir.com Fax image DIMM access error copyir.com FAX image DIMM copyir.com Main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com DP CIS copyir.com DP main PWB Main PWB
0640 Hard disk error
The hard disk cannot be accessed copyir.com HDD copyir.com Main PWB
0650 FAX image DIMM check error
A fax image DIMM which was used with another machine is installed copyir.com FAX DIMM copyir.com Main PWB copyir.com
0660 Hard disk encryption key error EEPROM copyir.com HDD copyir.com
0670 Hard disk overwriting erasure error HDD copyir.com Main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Main PWB
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com FAX software copyir.com FAX control PWB copyir.com
0840 Faults of RTC
(“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state copyir.com The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM) copyir.com The RTC setting is older than 00:01 on January 1, 2000 copyir.com [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked copyir.com 10 minutes have been passed since the previous check copyir.com After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T copyir.com’ Battery ( main PWB) copyir.com Main PWB copyir.com
0870 PCFAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com FAX control PWB copyir.com HDD copyir.com Main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com FAX control PWB copyir.com
0980 24 V power down detect
If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second copyir.com Power source PWB copyir.com
1000 MP lift motor error
If the MP lift sensor 1 (upper limit detect) or 2 (bottom detect) is not detectable to be turned on while the MP lift motor is ascending or descending copyir.com Manual feed lift base elevating mechanism copyir.com MP lift motor copyir.com MP lift sensor1 copyir.com MP lift sensor2 copyir.com Feed PWB 2 copyir.com Engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Cassette lift base elevating mechanism copyir.com Lift motor 1 copyir.com Lift sensor 1 copyir.com Feed PWB 2 copyir.com Engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 4 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 4 times successively copyir.com Cassette lift base elevating mechanism copyir.com Lift motor 2 copyir.com Lift sensor 2 copyir.com Feed PWB 2 copyir.com Engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com PF Lift motor 1 copyir.com PF Lift sensor 1 copyir.com PF main PWB copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism copyir.com PF Lift motor 2 copyir.com PF Lift sensor 2 copyir.com PF main PWB copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection Paper feeder lift base elevating mechanism copyir.com PF Lift motor1 copyir.com PF Lift sensor1 copyir.com PF main PWB copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection Paper feeder lift base elevating mechanism copyir.com PF Lift motor 2 copyir.com PF Lift sensor2 copyir.com PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Paper feeder lift base elevating mechanism copyir.com SD Lift motor copyir.com SD Lift sensor copyir.com SD main PWB copyir.com
1400 Rotary guide motor error
The guide sensor is not detected to be on at the home position detection with the rotary guide for three times in a row copyir.com Rotary guide motor copyir.com BR PWB copyir.com
1410 Rotary de-curler error
If the de-curler won’t turn On/ Off despite it has been activated for 400 steps during waiting for the de-curler sensor to be On/Off three times in a row copyir.com Rotary de-curler motor copyir.com BR PWB copyir.com
1710 Side multi tray incompatible detection error
The side multi tray has been installed with a device to which it is incompatible copyir.com The side multi tray is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder copyir.com PF main PWB copyir.com Engine PWB
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com PF main PWB (EEPROM) copyir.com
2101 Developer motor error
After developer motor is driven, the ready signal does not turn to L within 5 s copyir.com After developer motor is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Developer unit copyir.com Developer motor copyir.com Engine PWB copyir.com
2201 drum motor steady-state error
After drum motor is stabilized, the ready signal is at the H level for 5 s continuously copyir.com Drum unit copyir.com Drum motor copyir.com Engine PWB
2211 Drum motor startup error
Drum motor is not stabilized within 5 s since the motor is activated copyir.com Drum unit copyir.com Drum motor copyir.com Engine PWB copyir.com
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Fuser motor copyir.com Engine PWB copyir.com Feed PWB 1 copyir.com Fuser unit copyir.com
2500 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Paper feed motor copyir.com Engine PWB copyir.com
2550 Transfer motor error
After Transfer motor is driven, the ready signal does not turn to L within 2 s copyir.com After Transfer motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Transfer motor copyir.com Engine PWB copyir.com
2600 PF paper feed motor error (large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com PF paper feed motor copyir.com PF main PWB copyir.com
2810 Inner waste toner motor error
Initialized when an error is constantly observed for 2 seconds after the inner waste tonner motor is activated copyir.com An error is detected twice for 2 copyir.com5 seconds after rebooting copyir.com The lock detect signal won’t be H level three times in a row within 200 ms at 1 copyir.com25 ms cycles after the waste toner motor has been driven copyir.com Waste toner box copyir.com Waste toner motor copyir.com Engine PWBr box
3100 Scanner carriage error
The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor copyir.com The scanner mirror frame is being locked after setup copyir.com Scanner motor copyir.com Home position sensor copyir.com ISC PWB copyir.com Main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com CIS copyir.com DPSHD PWB copyir.com DP relay PWB copyir.com
3220 CCD lamp activation error
The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 1000 copyir.com CIS copyir.com ISC PWB copyir.com Main PWB copyir.com
3300 Optical system (AGC) error
One of the gains is FF or 00 during the CCD lamp AGC is being processed copyir.com LED lamp PWB copyir.com CCD PWB copyir.com ISC PWB copyir.com Main PWB copyir.com
3310 CIS AGC error
After AGC, correct input is not obtained at CIS copyir.com CIS copyir.com DPSHD PWB copyir.com
3500 Communication error
between scanner and ASIC An error code is detected copyir.com ISC PWB copyir.com Main PWB copyir.com
3600 Scanner sequence error ISC PWB
3700 Scanner device error CCD (ISU)
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com No response is received in 100 ms from AEF copyir.com ISC PWB copyir.com CCD PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Backup memory (ISC PWB) copyir.com
4001 Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Polygon motor (LSU) copyir.com Engine PWB copyir.com
4011 Polygon motor steady-state error
After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Polygon motor (LSU) copyir.com Engine PWB copyir.com
4101 BD initialization error K
After Polygon motor is driven, the BD signal is not detected for 1 s copyir.com PD PWB K (LSU) copyir.com Engine PWB copyir.com
4201 BD steady-state error K
The BD signal is not detected copyir.com PD PWB K (LSU) copyir.com Engine PWB copyir.com
5101 Main high-voltage error K
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board) copyir.com Drum unit copyir.com Charger roller unit copyir.com High voltage PWB copyir.com Engine PWB
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Fuser unit copyir.com Engine PWB copyir.com Power source PWB copyir.com Fuser heater copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Fuser unit copyir.com Engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Fuser thermistor 1 detects a lower then 30°C/86°F when the temperature at the fuser thermistor 2 is higher than 70°C/158°F for during werming up copyir.com Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during werming up copyir.com Fuser unit copyir.com Engine PWB copyir.com Fuser thermistor 1 copyir.com Fuser thermostat (triggered) copyir.com
6040 Fuser heater error
Input from fuser center thermistor 1 is abnormal value continuously for 1 s copyir.com CPU port PH1 to stay in H level for one second or more in all operating modes is judged that the connector is disconnected copyir.com Fuser unit copyir.com Engine PWB copyir.com Center thermistor 1 copyir.com Fuser thermostat (triggered)
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print copyir.com The temperature of thermistor 1 is detected to be less than 70°C/158°F for more than one second during lowpower mode copyir.com Power source copyir.com Fuser unit copyir.com Engine PWB copyir.com Fuser thermistor 1 copyir.com Fuser thermostat (triggered) copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 30 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Fuser unit copyir.com Engine PWB copyir.com Fuser center thermistor 1 copyir.com
6220 Abnormally high fuser edge thermistor temperature
Fuser thermistor 2 detects a temperature higher than 220°C/428°F for 1 s copyir.com Fuser unit copyir.com Engine PWB copyir.com
6230 Broken fuser edge thermistor wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F copyir.com Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during werming up copyir.com Fuser unit copyir.com Engine PWB
6250 Abnormally low fuser edge thermistor temperature
Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print copyir.com Fuser thermistor 2 detects a temperature lower than 50°C/ 122°F for 1 s during low power mode copyir.com Fuser unit copyir.com Engine PWB copyir.com
6320 Abnormally high fuser middle thermistor 3 temperature
Fuser middle thermistor 3 detects a temperature higher than 205°C/401°F for 1 s copyir.com Fuser unit copyir.com Engine PWB copyir.com
6400 Zero-cross signal error
While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s copyir.com Fuser unit copyir.com
6610 Fuser release sensor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 8 s copyir.com Fuser release motor copyir.com Fuser release sensor copyir.com Engine PWB copyir.com
6910 Engine software ready error
The device won’t engage in ready state in 60 minutes after warming-up has began copyir.com (A previous timeout process has not been cancelled copyir.com) Engine PWB copyir.com
7001 Toner motor error
A state that a lock is detected 5 times in a row in 200ms cycle when the Toner motor is driven has occurred 30 times in total copyir.com Toner container copyir.com Toner motor copyir.com Screw sensor copyir.com Engine PWB copyir.com
7101 Toner sensor error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Failure of locking the developer waste slot at setup copyir.com Toner sensor copyir.com Toner motor copyir.com Engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire
The sensor input sampling is greater than 230 copyir.com Outer temperature sensor 2 copyir.com Front PWB copyir.com Engine PWB copyir.com
7210 Short-circuited outer temperature sensor 2
The sensor input sampling is less than 69 copyir.com Outer temperature sensor 2 copyir.com Front PWB copyir.com Engine PWB copyir.com
7221 Broken LSU thermistor wire
The sensor input sampling is greater than 230 copyir.com LSU thermistor copyir.com LSU relay PWB copyir.com Engine PWB copyir.com
7231 Short-circuited LSU thermistor K
The sensor input sampling is less than 69 copyir.com LSU thermistor copyir.com LSU relay PWB copyir.com Engine PWB copyir.com
7241 Broken Developer thermistor wire
The sensor input sampling is greater than 230 copyir.com Developer thermistor copyir.com Front PWB copyir.com Engine PWB copyir.com
7251 Short-circuited Developer thermistor
The sensor input sampling is less than 69 copyir.com Developer thermistor copyir.com Front PWB copyir.com Engine PWB copyir.com
7301 Toner hopper motor error
During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets copyir.com Tonner hopper motor copyir.com Screw sensor copyir.com Engine PWB copyir.com
7401 Developer unit type mismatch error
Improper adaptation of the machine and developer unit is detected copyir.com Different type of the developer unit is installed copyir.com Developer unit copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com Developer shutter sensor copyir.com
7601 ID sensor 1 error [Front]
Dark potential error FrontDarkP and FrontDarkS are greater than 0 copyir.com80V copyir.com Light potential error FrontBrightS is smaller than FrontDarkS copyir.com FrontBrightP is smaller than [FrontDarkP + 0 copyir.com5V] copyir.com ID sensor1 copyir.com Feed PWB 1 copyir.com Engine PWB copyir.com
7602 ID sensor 2 error [Rear]
Dark potential error RearDarkP and RearDarkS are greater than 0 copyir.com80V copyir.com Light potential error RearBrightS is smaller than RearDarkS copyir.com RearBrightP is smaller than [RearDarkP + 0 copyir.com5V] copyir.com ID sensor 2 copyir.com Feed PWB 1 copyir.com Engine PWB copyir.com
7800 Broken outer temperature sensor wire
The device did not respond for more than 5 ms during reading, in 5 times copyir.com Outer temperature sensors been locked copyir.com Front PWB copyir.com Engine PWB copyir.com
7901 Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com DR PWB copyir.com Front PWB copyir.com Engine PWB copyir.com
7911 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit copyir.com Front PWB copyir.com Engine PWB copyir.com
7941 Laser scanner unit EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com APC PWB copyir.com LSU relay PWB copyir.com Engine PWB copyir.com
8010 Punch motor 1 error
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Punch motor copyir.com Punch home position sensor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8020 Punch motor 2 error
Home position is not obtained in 3 s after home position is initialized or in standby copyir.com Punch motor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8030 Punch motor 3 error Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Punch motor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com DF paddle motor copyir.com DF paddle sensor copyir.com DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com DF eject release motor DF bundle discharge unit sensor copyir.com DF bundle discharge unit sensor copyir.com DF main PWB copyir.com
8110 DF shift motor 1 error (4000-sheet finisher)
DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven copyir.com DF shift motor 1 [front] copyir.com DF shift sensor 1 [front] copyir.com DF main PWB copyir.com
8120 DF shift motor 2 error (4000-sheet finisher)
DF shift sensor 2 won’t turn on when it has travelled 160 mm after DF shift motor 2 is driven copyir.com DF shift motor 2 [rear] copyir.com DF shift sensor 2 [rear] copyir.com DF main PWB copyir.com
8130 DF shift release motor error (4000-sheet finisher)
When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com DF shift release motor copyir.com DF shift release sensor copyir.com DF main PWB copyir.com
8140 DF tray error 1
When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com DF tray motor copyir.com DF tray sensor 1 copyir.com DF tray upper surface sensor copyir.com DF main PWB copyir.com
8150 DF tray error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s copyir.com DF tray motor copyir.com DF tray sensor copyir.com 1 DF tray upper surface sensor copyir.com DF main PWB
8160 DF tray error 3
When the main tray has descended, DF tray sensor 4 does not turn on within 20 s copyir.com DF tray motor copyir.com DF tray sensor 4 copyir.com DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com DF side registration motor 1 copyir.com DF side registration sensor 1 copyir.com DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 ( jam in front of width alignment) is detected twice copyir.com DF side registration motor 1 copyir.com DF side registration sensor 1 copyir.com DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com DF side registration motor 2 copyir.com DF side registration sensor 2 copyir.com DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 ( jam in rear of width alignment) is detected twice copyir.com DF side registration motor 2 copyir.com DF side registration sensor 2 copyir.com DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com DF slide motor copyir.com DF staple sensor copyir.com DF main PWB copyir.com
8230 DF staple motor error 1
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven copyir.com) DF staple motor copyir.com DF staple sensor copyir.com DF main PWB copyir.com
8240 DF staple motor error 2
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven copyir.com) DF staple motor copyir.com DF main PWB copyir.com
8250 DF tray motor error 4
During driving the motor, the lock signal is detected for 10 s continuously copyir.com DF tray motor copyir.com DF tray sensor 3 copyir.com DF main PWB copyir.com
8300 CF unit communication error (4000-sheet finisher)
Communication with the center- folding unit is not possible copyir.com CF unit set switch copyir.com CF main PWB copyir.com DF main PWB copyir.com
8310 CF side registration motor 2 error (4000-sheet finisher)
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com CF side registration motor 2 copyir.com CF side registration sensor 2 copyir.com CF main PWB copyir.com
8320 CF adjustment motor error (4000-sheet finisher)
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com CF adjustment motor1,2 copyir.com CF adjustment sensor1,2 copyir.com CF main PWB copyir.com
8330 CF blade motor error (4000-sheet finisher)
When initial operation, CF blade sensor does not turn on within 1500 ms copyir.com CF blade motor copyir.com CF blade sensor copyir.com CF main PWB copyir.com
8340 CF staple motor error 1 (4000-sheet finisher)
Staple JAM (center-folding unit) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven copyir.com) CF staple motor copyir.com CF staple sensor copyir.com CF main PWB copyir.com
8350 CF side registration motor 1 error (4000-sheet finisher)
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com CF side registration motor 1 copyir.com CF side registration sensor 1 copyir.com CF main PWB copyir.com
8360 CF main motor error (4000-sheet finisher)
During driving the motor, the lock signal is detected for 1 s continuously copyir.com CF main motor copyir.com CF main PWB copyir.com
8370 CF staple motor error 2 (4000-sheet finisher)
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 1000 ms continuously, while the stapler motor was driven copyir.com) CF staple motor copyir.com CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Punch slide motor copyir.com Punch slide sensor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Punch slide motor copyir.com Punch paper edge sensor 1,2 copyir.com Punch PWB motor copyir.com DF main PWB copyir.com
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Punch PWB copyir.com DF main PWB copyir.com
8500 Mailbox communication error (4000-sheet finisher)
Communication failed to be established after the mailbox was hooked up copyir.com MB main PWB copyir.com DF main PWB copyir.com
8510 MB conveying motor error 1 (4000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s copyir.com MB conveying motor copyir.com MB home position sensor copyir.com MB main PWB copyir.com
8520 MB conveying motor error 2 (4000-sheet finisher)
When standby operation, MB home position sensor does not turn off within 1 s copyir.com MB conveying motor copyir.com MB home position sensor copyir.com MB main PWB copyir.com
8800 Document finisher main program error
Document finisher main program error at power up copyir.com DF main PWB copyir.com Engine PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com DF main PWB copyir.com
8930 Center-folding unit backup error (4000-sheet finisher)
Read and write data does not match 3 times in succession copyir.com CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com DP main PWB copyir.com SC PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com U206 setting copyir.com Coin vender control PWB copyir.com Engine PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse copyir.com (Three recovery times copyir.com) The above has been detected 5 times copyir.com * The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transpoting copyir.com The accumulated number must be cleared at completion of a normal rise copyir.com The default threshold is 5 copyir.com DP lift motor copyir.com DP lift sensor 1 copyir.com DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse copyir.com (Three recovery times copyir.com) The above has been detected 5 times copyir.com DP lift motor copyir.com DP lift sensor 2 copyir.com DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com DP main PWB copyir.com Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com DP SHD PWB copyir.com
9080 LED fault detection
A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex copyir.com DP CIS copyir.com DP SHD PWBS copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Coin vender control PWB copyir.com
9110 Coin vender rejector error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube copyir.com Contact in the connector copyir.com Change empty sensor copyir.com Coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube copyir.com Contact in the connector copyir.com Change empty sensor copyir.com Coin vender control PWB copyir.com
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube copyir.com Contact in the connector copyir.com Change empty sensor copyir.com Coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Change tube copyir.com Contact in the connector copyir.com Change empty sensor copyir.com Coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Pay-out area copyir.com Pay-out motor copyir.com Pay-out sensor copyir.com
9500 ISC PWB error A Main PWB copyir.com ISC PWB copyir.com
9510 ISC PWB error B Main PWB copyir.com DP SHD PWB copyir.com
9520 ISC PWB error C Main PWB copyir.com ISC PWB copyir.com
9940 Confidential document guard uninstalled error
The confidential document guard PWB is removed while the confidential document guard PWB is valid copyir.com Confidential document guard PWB
9950 ISC PWB error C
FPGA configuration error CPU version information error This is caused when the PWB of a double-side scanning DP is connected, the confidential guard PWB is inserted, and the harness is not correctly connected Confidential document guard PWB
F000 Communication error between Main PWB and Operation PWB Main PWB copyir.com Operation PWB
F010 Main PWB checksum error Main PWB copyir.com
F040 Communication error between Main PWB and Print engine Main PWB copyir.com Engine PWB copyir.com HDD
F041 Communication error between Main PWB and Scanner engine Main PWB copyir.com ISC PWB copyir.com
F050 Print engine ROM checksum error Engine software copyir.com Engine PWB copyir.com
F051 Scanner engine ROM checksum error Scanner software copyir.com ISC PWB
F278 Power supply in drive system error The main power switch was turned off before the power switch is pressed copyir.com Shutdown due to a power failure
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.