درایور فتوکپی ریکو MP 3353
1404-08-05
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
C021 Developer unit motor copyir copyir.comcomYMC locking error: The developer unit motor copyir copyir.comcomYMC is not rotating normally copyir copyir.comcom
C022 Developer unit mixer motor copyir copyir.comcomYMC locking error: The developer unit mixer motor copyir copyir.comcomYMC is not rotating normally
C023 Developer unit motor copyir copyir.comcomK locking error: The developer unit motor copyir copyir.comcomK is not rotating normally copyir copyir.comcom
C024 Developer unit mixer motor copyir copyir.comcomK locking error: The developer unit mixer motor copyir copyir.comcomK is not rotating normally copyir copyir.comcom
C130 1st drawer tray abnormality: The tray copyir copyir.comcomup motor is not rotating or the 1st drawer tray is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the 1st drawer)
C140 2nd drawer tray abnormality: The tray copyir copyir.comcomup motor is not rotating or the 2nd drawer tray is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the 2nd drawer)
C150 3rd drawer tray abnormality: The 3rd drawer tray copyir copyir.comcomup motor is not rotating or the 3rd drawer tray is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the 3rd drawer)
C160 4th drawer tray abnormality: The 4th drawer tray copyir copyir.comcomup motor is not rotating or the 4th drawer tray is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the 4th drawer)
C180 LCF tray copyir copyir.comcomup motor abnormality: The LCF tray copyir copyir.comcomup motor is not rotating or the LCF tray is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the LCF)
C1A0 LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally copyir copyir.comcom (the case that paper can be fed from any drawer except the LCF)
C1C0 Option LCF tray copyir copyir.comcomup motor abnormality: The option LCF tray copyir copyir.comcomup motor is not moving normally
C260 Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON copyir copyir.comcom
C270 (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time copyir copyir.comcom (2) Downloading firmware with an incorrect model copyir copyir.comcom
C280 Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time copyir copyir.comcom
C360 Needle electrode cleaner operation abnormality
C370 Transfer belt operation abnormality
C380 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomK abnormality (upper limit)
C381 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomK abnormality (lower limit)
C382 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomK connection error
C390 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomC abnormality (upper limit)
C391 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomC abnormality (lower limit)
C392 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomC connection error
C3A0 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomM abnormality (upper limit)
C3A1 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomM abnormality (lower limit)
C3A2 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomM connection error
C3B0 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomY abnormality (upper limit)
C3B1 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomY abnormality (lower limit)
C3B2 Auto copyir copyir.comcomtoner sensor copyir copyir.comcomY connection error
C3C0 Process unit connection error
C411 Thermistor or heater lamp abnormality at power copyir copyir.comcomON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON copyir copyir.comcom
C412 Thermistor/heater lamp abnormality at power copyir copyir.comcomON: Thermistor abnormality is detected at power copyir copyir.comcomON or the fuser belt temperature does not rise within a specified period of time after power copyir copyir.comcomON copyir copyir.comcom
C443 Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)
C445 Heater lamp abnormality after abnormality judgment (pre copyir copyir.comcomrunning end temperature abnormality)
C446 Heater lamp abnormality after abnormality judgment (pre copyir copyir.comcomrunning end temperature abnormality)
C447 Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)
C448 Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified
C451 Thermopile and edge thermistor temperature difference
C452 Thermopile temperature difference
C461 Pressure roller heater 40°C detection (Not determined)
C462 Pressure roller heater 40°C detection (Determined)
C463 Pressure roller thermistor and edge thermistor temperature difference
C464 Pressure roller thermistor temperature difference
C465 Pressure roller thermistor abnormality after entering ready status (pre copyir copyir.comcomrunning end temperature abnormality)
C466 Pressure roller thermistor abnormality after entering ready status (pre copyir copyir.comcomrunning end temperature abnormality)
C467 Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status)
C468 Pressure roller thermistor abnormality after entering ready status (overheating)
C471 IH board initialization abnormality
C472 Power supply abnormality
C473 Surge pressure detection / power and voltage upper limit abnormality
C474 Power and voltage lower limit abnormality
C476 IH low power supply
C480 IGBT high temperature abnormality
C481 IH drive circuit abnormality
C490 IH circuit abnormality / IH coil abnormality
C4B0 Fuser unit counter abnormality
C4B1 Fuser unit voltage judgment abnormality
C4D0 Fuser belt thermopile abnormality
C4E0 Fuser unit releasing operation abnormality copyir copyir.comcom Though the pressure roller is released copyir copyir.comcom its position cannot be detected copyir copyir.comcom
C4E1 Fuser unit contacting operation abnormality copyir copyir.comcom Though the pressure roller is contacted copyir copyir.comcom its position cannot be detected copyir copyir.comcom
C4E2 Fuser belt rotation detection sensor abnormality copyir copyir.comcom The fuser belt does not rotate or incorrectly rotates copyir copyir.comcom
C4E3 Fuser motor rotation abnormality
C550 RADF I/F error: Communication error has occurred between the RADF and the scanner copyir copyir.comcom
C560 Communication error between Engine copyir copyir.comcomCPU and PFC board
C570 Communication error between Engine copyir copyir.comcomCPU and CNV board
C580 Communication error between CNV board and finisher
C5A0 SRAM board not connected (LGC board)
C5A1 SRAM board data abnormality (LGC board)
C730 RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed copyir copyir.comcom
C880 RADF original feed motor abnormality: An error signal has been detected when the motor is rotating copyir copyir.comcom
C890 RADF read motor abnormality: An error signal has been detected when the motor is rotating copyir copyir.comcom
C8A0 RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating copyir copyir.comcom
C8B0 RADF original exit motor abnormality: An error signal has been detected when the motor is rotating copyir copyir.comcom
C8C0 RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed copyir copyir.comcom but is ended unsuccessfully copyir copyir.comcom
C8E0 RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred copyir copyir.comcom
C900 Connection error between SYS board and LGC board
C940 Engine copyir copyir.comcomCPU abnormality
C962 LGC board ID abnormality
C970 High copyir copyir.comcomvoltage transformer abnormality: Leakage of the main charger is detected copyir copyir.comcom
C9E0 Connection error between SLG board and SYS board
CA00 Image position alignment abnormality
CA10 Polygonal motor abnormality: The polygonal motor is not rotating normally
CA20 H copyir copyir.comcomSync detection error: H copyir copyir.comcomSync signal detection PC board cannot detect laser beams copyir copyir.comcom
CA47 SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking copyir copyir.comcom
CB00 Finisher not connected: Communication error has occurred between the equipment and finisher copyir copyir.comcom [MJ1103/1104]
CB01 Finisher communication error: Communication error has occurred between the equipment and finisher copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB10 Entrance motor abnormality: The entrance motor is not rotating normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB11 Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB12 Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB13 Finisher exit motor abnormality
CB14 Paper holding arm motor abnormality
CB30 Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB31 Movable tray paper copyir copyir.comcomfull detection error: The actuator of the movable tray paper copyir copyir.comcomfull detection sensor does not move smoothly copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB40 Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/ 1104]
CB50 Stapler home position error: The stapler home position sensor does not work copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB51 Stapler shift home position error: The stapler is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB60 Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB80 Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON
CB81 Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CB82 Finisher copyir copyir.comcom Main CPU program error
CB83 Saddle Stitch Finisher copyir copyir.comcom Main CPU program error
CB84 Hole Punch Unit copyir copyir.comcom Main CPU program error
CB91 Saddle Stitch Finisher flash ROM abnormality
CB92 Saddle Stitch Finisher RAM abnormality
CB93 Additional folding motor abnormality
CB94 Saddle transport motor abnormality
CB95 Stacker motor abnormality
CBA0 Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CBB0 Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CBC0 Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CBE0 Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CC20 Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ copyir copyir.comcom1103/1104]
CC30 Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CC31 Transport motor abnormality: The transport motor is not rotating or the stack transport roller copyir copyir.comcom1 and copyir copyir.comcom2 is not rotating normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CC41 Paper holder cam home position abnormality: The paper holder cam is not at the home position copyir copyir.comcom [MJ1103/1104]
CC51 Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
CC52 Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
CC60 Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally copyir copyir.comcom [MJ1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
CC61 Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
CC71 Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir copyir.comcom [MJ copyir copyir.comcom1103/ 1104 (when MJ copyir copyir.comcom6102 is installed)]
CC72 Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on copyir copyir.comcom [MJ copyir copyir.comcom1103/ 1104 (when MJ copyir copyir.comcom6102 is installed)]
CC73 Punching device power supply abnormality
CC74 Punch unit transport pulse abnormality
CC80 Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
CD60 Sub copyir copyir.comcomhopper toner sensors abnormality copyir copyir.comcom
CD61 Sub copyir copyir.comcomhopper toner motor copyir copyir.comcomY abnormality copyir copyir.comcom
CD62 Sub copyir copyir.comcomhopper toner motor copyir copyir.comcomM abnormality copyir copyir.comcom
CD63 Sub copyir copyir.comcomhopper toner motor copyir copyir.comcomC abnormality copyir copyir.comcom
CD64 Sub copyir copyir.comcomhopper toner motor copyir copyir.comcomK abnormality copyir copyir.comcom
CD71 Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate copyir copyir.comcom
CD80 TRU waste toner motor locking error: The auger (TRU side) in the TRU waste toner transport path does not rotate copyir copyir.comcom
CD81 TRU waste toner transport motor locking error: The auger (waste toner box side) in the TRU waste toner transport path does not rotate copyir copyir.comcom
CD82 TRU waste toner full copyir copyir.comcomstatus error
CDE0 Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally copyir copyir.comcom [MJ1103/1104]
CE00 Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
CE10 Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF copyir copyir.comcom
CE20 Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed copyir copyir.comcom
CE40 Image quality control test pattern abnormality: The test pattern is not formed normally copyir copyir.comcom
CE41 Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally copyir copyir.comcom
CE42 Image quality TRC control test pattern abnormality (EFI printer board): Image quality TRC control test pattern is not printed normally copyir copyir.comcom
CE50 Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range copyir copyir.comcom
CE60 Drum thermistor copyir copyir.comcomY abnormality: The output value of the drum thermistor copyir copyir.comcomY is out of a specified range copyir copyir.comcom
CE71 Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time copyir copyir.comcom
CE90 Drum thermistor copyir copyir.comcomK abnormality: The output value of the drum thermistor copyir copyir.comcomK is out of a specified range copyir copyir.comcom
CEC0 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally copyir copyir.comcom
CF10 Communication module SRAM reading failure copyir copyir.comcom
CF90 Laser optical unit shutter abnormality copyir copyir.comcom
CFA0 Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal copyir copyir.comcom
CFA1 Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal copyir copyir.comcom
E010 Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor copyir copyir.comcom
E011 Transfer belt paper copyir copyir.comcomclinging jam: The paper after the 2nd transfer is clinging to the transfer belt copyir copyir.comcom or a paper jam occurred between the registration roller and the paper clinging detection sensor copyir copyir.comcom
E020 Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor copyir copyir.comcom
E030 Power copyir copyir.comcomON jam: The paper is remaining on the paper transport path when power is turned ON copyir copyir.comcom
E061 Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment copyir copyir.comcom
E062 Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment copyir copyir.comcom
E063 Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment copyir copyir.comcom
E064 Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment copyir copyir.comcom
E065 Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment copyir copyir.comcom
E071 1st drawer media type mis copyir copyir.comcomsetting jam: The media type setting of the 1st drawer is incorrect copyir copyir.comcom
E072 2nd drawer media type mis copyir copyir.comcomsetting jam: The media type setting of the 2nd drawer is incorrect copyir copyir.comcom
E073 3rd drawer media type mis copyir copyir.comcomsetting jam: The media type setting of the 3rd drawer is incorrect copyir copyir.comcom
E074 4th drawer media type mis copyir copyir.comcomsetting jam: The media type setting of the 4th drawer is incorrect copyir copyir.comcom
E075 Option LCF media type mis copyir copyir.comcomsetting jam: The media type setting of the option LCF is incorrect copyir copyir.comcom
E076 Tandem LCF media type mis copyir copyir.comcomsetting jam: The media type setting of the tandem LCF is incorrect copyir copyir.comcom
E090 Image data delay jam: Image data to be printed cannot be prepared copyir copyir.comcom
E091 Motor copyir copyir.comcomON time copyir copyir.comcomout jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware copyir copyir.comcom
E0A0 Image transport ready time copyir copyir.comcomout jam: Image data to be printed cannot be sent copyir copyir.comcom
E110 ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing copyir copyir.comcom
E120 Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor copyir copyir.comcom
E130 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor copyir copyir.comcom
E140 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor copyir copyir.comcom
E150 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
E160 4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor copyir copyir.comcom
E180 Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor copyir copyir.comcom
E190 LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor copyir copyir.comcom
E200 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir copyir.comcom
E210 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir copyir.comcom
E220 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir copyir.comcom
E230 1st drawer misfeeding (Paper not reaching the 1st drawer transport sensor): Paper fed from the 1st drawer does not reach the 1st drawer transport sensor copyir copyir.comcom
E240 2nd drawer misfeeding (Paper not reaching the 2nd drawer transport sensor): Paper fed from the 2nd drawer does not reach the 2nd drawer transport sensor copyir copyir.comcom
E260 Option LCF transport jam (Paper not reaching the registration sensor)
E270 Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor copyir copyir.comcom
E290 Option LCF transport jam: Paper fed from the Option LCF does not reach the 1st drawer transport sensor copyir copyir.comcom
E2B0 Stop jam at the registration sensor (1st drawer)
E2B1 Stop jam at the registration sensor (2nd drawer)
E2B2 Stop jam at the registration sensor (3rd drawer)
E2B3 Stop jam at the registration sensor (4th drawer)
E2B4 Stop jam at the registration sensor (Bypass tray)
E2B5 Stop jam at the registration sensor (LCF)
E2B6 Stop jam at the registration sensor (ADU)
E2B7 Stop jam at the registration sensor (option LCF)
E300 3rd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir copyir.comcom
E310 3rd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir copyir.comcom
E320 3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir copyir.comcom
E330 4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor copyir copyir.comcom
E340 4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor copyir copyir.comcom
E350 4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor copyir copyir.comcom
E360 4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor copyir copyir.comcom
E370 3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor copyir copyir.comcom
E380 4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor copyir copyir.comcom
E3C0 LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor copyir copyir.comcom
E3D0 LCF transport jam (Paper not reaching the 1st drawer feed sensor): Paper fed from the LCF and passed through the 2nd drawer feed sensor does not reach the 1st drawer feed sensor copyir copyir.comcom
E3E0 LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor copyir copyir.comcom
E3F0 Tandem LCF misfeeding (Paper not reaching the tandem LCF feed sensor): Paper fed from the Tandem LCF does not reach the tandem LCF transport sensor copyir copyir.comcom
E400 Duplexing unit open jam
E430 ADU open jam: The ADU has opened during printing copyir copyir.comcom
E440 Paper feed cover open jam: The paper feed cover has opened during printing copyir copyir.comcom
E450 LCF side cover open jam: The LCF side cover has opened during printing copyir copyir.comcom
E480 Bridge unit open jam: The bridge unit has opened during printing copyir copyir.comcom
E4A0 Waste toner cover open jam (printing)
E4B0 Bridge unit open jam (printing): The bridge unit has opened during printing copyir copyir.comcom
E510 Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section copyir copyir.comcom
E511 ADU misfeeding (Paper not reaching the ADU transport sensor copyir copyir.comcom1)
E540 ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor copyir copyir.comcom
E550 Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding) copyir copyir.comcom
E570 Jam not reaching the bridge unit copyir copyir.comcom
E580 Stop jam at the bridge unit
E590 Jam not reaching the upper paper exit sensor
E5A0 Stop jam at the upper paper exit sensor
E712 Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor copyir copyir.comcom
E714 Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray copyir copyir.comcom
E721 Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side) copyir copyir.comcom
E722 Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section copyir copyir.comcom
E724 Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor copyir copyir.comcom
E725 Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor copyir copyir.comcom
E726 Transport/exit signal reception jam during ADF standby status
E727 Jam not reaching the original reading end sensor
E729 Stop jam at the original reading end sensor
E731 Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor copyir copyir.comcom
E744 Stop jam at the exit/reverse sensor
E745 Jam not reaching the exit reverse sensor
E746 Exit/reverse sensor paper remaining jam
E762 Registration sensor paper remaining jam
E770 Original width detection sensor copyir copyir.comcom1 paper remaining jam
E771 Original width detection sensor copyir copyir.comcom2 paper remaining jam
E772 Original width detection sensor copyir copyir.comcom3 paper remaining jam
E773 Intermediate transport sensor paper remaining jam
E774 Reading start sensor paper remaining jam
E775 Reading end sensor paper remaining jam
E777 Exit sensor paper remaining jam
E860 Original jam access cover open: The Original jam access cover has opened during RADF operation copyir copyir.comcom
E870 RADF open jam: RADF has opened during RADF operation copyir copyir.comcom
E871 Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment copyir copyir.comcom
E910 Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor copyir copyir.comcom
E920 Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor copyir copyir.comcom
E930 Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1 copyir copyir.comcom
E940 Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2 copyir copyir.comcom
E970 Jam not reaching the lower paper exit sensor: Paper transported from the bridge unit does not reach the lower paper exit sensor copyir copyir.comcom
E980 Stop jam at the lower paper exit sensor: Paper transported from the bridge unit does not pass the lower paper exit sensor copyir copyir.comcom
E9F0 Punching jam: Punching is not performed properly copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
EA10 Paper transport delay jam: The paper which has passed the relay transport path does not reach the inlet sensor copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA20 Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir copyir.comcom [MJ1103/1104]
EA21 Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA22 Paper transport jam (Finisher paper punching edge detection sensor): [MJ copyir copyir.comcom1103/1104]
EA23 Paper transport jam (exit sensor): [MJ copyir copyir.comcom1103/1104]
EA24 Paper transport jam (between entrance and exit sensors): [MJ copyir copyir.comcom1103/1104]
EA25 Paper transport jam (after paper stack exit): [MJ1103/1104]
EA26 Paper transport jam (stop command request): [MJ1103/1104]
EA27 Paper transport jam (paper not inserted): [MJ copyir copyir.comcom1103/ 1104]
EA28 Paper transport jam (assisting arm operation delay): [MJ copyir copyir.comcom1103/1104]
EA29 Paper transport jam (stack transport delay): [MJ1103/1104]
EA31 Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA32 Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA40 Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing copyir copyir.comcom [MJ copyir copyir.comcom1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA50 Stapling jam: Stapling is not performed properly copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA60 Early arrival jam: The inlet sensor detects the paper earlier than a specified timing copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA70 Stack exit belt home position error: The stack exit belt is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EA90 Door open jam: The delivery cover or inlet cover has opened during printing [MJ copyir copyir.comcom1103/1104] copyir copyir.comcom
EAA0 Power copyir copyir.comcomON jam: Paper exists at No copyir copyir.comcom1 paper sensor copyir copyir.comcom No copyir copyir.comcom 2 paper sensor copyir copyir.comcom No copyir copyir.comcom3 paper sensor copyir copyir.comcom vertical path paper sensor or delivery sensor when power is turned ON copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EAB0 Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No copyir copyir.comcom1 paper sensor copyir copyir.comcom No copyir copyir.comcom 2 paper sensor copyir copyir.comcom No copyir copyir.comcom3 paper sensor or delivery sensor copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EAB1 Short paper jam (Saddle Stitch Finisher)
EAD0 Print end command time copyir copyir.comcomout jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing copyir copyir.comcom
EAE0 Receiving time time copyir copyir.comcomout jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher copyir copyir.comcom
EB30 Ready time time copyir copyir.comcomout jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing copyir copyir.comcom
EB50 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper copyir copyir.comcom
EB60 Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]) copyir copyir.comcom
ED10 Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ copyir copyir.comcom6102 is installed)]
ED11 Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104 (when MJ6102 is installed)]
ED12 Shutter home position error: The shutter is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
ED13 Front alignment plate home position error: The front alignment plate is not at the home position copyir copyir.comcom [MJ1103/1104]
ED14 Rear alignment plate home position error: The rear alignment plate is not at the home position copyir copyir.comcom [MJ1103/1104]
ED15 Paddle home position error: The paddle is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
ED16 Buffer tray home position error: The buffer tray is not at the home position copyir copyir.comcom [MJ copyir copyir.comcom1103/1104]
EF10 Paper not supported for Saddle Stitch Finisher
EF11 Saddle Stitch Finisher stapling error (front)
EF12 Saddle Stitch Finisher stapling error (rear)
EF13 Saddle paper holder home position detection abnormality
EF14 Saddle paper exit jam
EF15 Saddle Stitch Finisher side alignment motor home position detection abnormality
EF16 Saddle Stitch Finisher stacker motor home position detection abnormality
EF17 Saddle Stitch Finisher folding blade home position detection abnormality
EF18 Saddle Stitch Finisher additional folding roller home position detection abnormality
EF19 Saddle paper folding jam
EF20 Saddle stacker jam
EF21 Hole Punch Unit paper leading edge skew detection abnormality
EF22 Hole Punch Unit paper leading edge detection abnormality
EF23 Hole Punch Unit paper alignment abnormality
EF24 Hole Punch Unit paper trailing edge skew detection abnormality
EF25 Hole Punch Unit paper trailing edge detection abnormality
EF27 Hole Punch Unit paper edge detection order abnormality copyir copyir.comcom1
EF28 Hole Punch Unit paper edge detection order abnormality copyir copyir.comcom2
F070 Communication error between System copyir copyir.comcomCPU and Engine copyir copyir.comcomCPU
F090 SRAM abnormality on the SYS board
F100 HDD format error: HDD cannot be initialized normally copyir copyir.comcom
F101 HDD unmounted: Connection of HDD cannot be detected copyir copyir.comcom
F102 HDD start error: HDD cannot become ‘Ready’ state
F103 HDD transfer time copyir copyir.comcomout: Reading/writing cannot be performed in the specified period of time copyir copyir.comcom
F104 HDD data error: Abnormality is detected in the data of HDD copyir copyir.comcom
F105 HDD other error
F106 Point and Print partition damage
F107 /BOX partition damage
F108 /SHA partition damage
F110 Communication error between System copyir copyir.comcomCPU and Scanner copyir copyir.comcomCPU
F111 Scanner response abnormality
F120 Database abnormality: Database is not operating normally copyir copyir.comcom
F130 Invalid MAC address
F200 Data Overwrite option (GP copyir copyir.comcom1070) disabled
F350 SLG board abnormality
F400 SYS board cooling fan abnormality
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.