درایور فتوکپی ریکو MP 3353
1404-08-05
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem copyir.com Defective FAX control PWB copyir.com
0060 Illegal engine PWB type
The engine main PWB and the engine sub PWB are incompatible copyir.com Defective engine sub PWB copyir.com
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0100 Backup memory device error Defective flash memory copyir.com
Defective main PWB copyir.com
0120 MAC address data error
For data in which the MAC address is invalid copyir.com Defective flash memory
Defective engine PWB copyir.com
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Improper installation EEPROM copyir.com
Device damage of EEPROM copyir.com
0160 Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal copyir.com Data damage of EEPROM copyir.com
0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters copyir.com Data damage of EEPROM copyir.com
Defective PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0620 FAX image DIMM error
DIMM is not installed correctly copyir.com DIMM cannot be accessed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com Poor contact in the connector terminals copyir.com
Defective main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com Defective hard disk copyir.com
Defective main PWB copyir.com
0650 FAX image DIMM check error
Improper DIMM is installed copyir.com DIMM installed incorrectly copyir.com
Defective main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Defective main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com Defective FAX software copyir.com
Defective FAX control PWB copyir.com
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed copyir.com The battery is disconnected from the main PWB
Defective main PWB copyir.com
0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times Improper installation FAX control PWB copyir.com
Defective FAX control PWB or main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com Defective FAX control PWB copyir.com
0970 12 V power down detect Power is disconnected during sleeping copyir.com Defective power source PWB copyir.com
0980 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected copyir.com Defective power source PWB copyir.com
1000 MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 3 s copyir.com Defective MP plate elevation mechanism copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective MP lift motor copyir.com
Defective engine PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 1 copyir.com
Defective engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective lift motor 2 copyir.com
Defective engine PWB copyir.com
1050 SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor
Defective SM lift motor copyir.com
Defective SM main PWB copyir.com
1060 PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1070 PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed copyir.com Defective bottom plate elevation mechanism in the cassette copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1100 PF lift motor 1 error
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 1 copyir.com
Defective PF main PWB copyir.com
1110 PF lift motor 2 error
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF lift motor 2 copyir.com
Defective PF main PWB copyir.com
1140 SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s copyir.com The lock signal of the motor is detected continuously for 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD lift motor copyir.com
Defective SD main PWB copyir.com
1250 SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1350 SM multi feed sensor error (side multi tray)
The SM multi feed sensor has detected multi feeding 5 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1410 BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps (3 times in succession) copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective BR decurler motor copyir.com
Defective BR main PWB copyir.com
Defective engine PWB copyir.com
1450 SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession copyir.com Deleting a block has failed three times in a row copyir.com Writing won’t complete in 200 ms after writing has commenced copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective SM multi feed sensor copyir.com
Defective SM main PWB copyir.com
1720 Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible copyir.com The paper feeder is installed with a device to which it is incompatible copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective PF main PWB copyir.com
1810 Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side multi tray copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
1820 Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Improper installation side paper feeder copyir.com
Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
Defective SM main PWB copyir.com
Defective PF main PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
1910 Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective SM main PWB copyir.com
Device damage of EEPROM copyir.com
1920 Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective PF main PWB copyir.com
Device damage of EEPROM copyir.com
2101 Developer motor error
After developer motor is driven, the ready signal does not turn to L within 2 s copyir.com After developer motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective developer motor copyir.com
Defective engine PWB copyir.com
2201 Drum motor steady-state error
The ready signal won’t turn to L in 2 seconds after the drum motor is started copyir.com After drum motor is stabilized, the ready signal is at the H level for 5 s continuously copyir.com The device won’t engage in ready state in 60 minutes after warming-up has began copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective drum motor copyir.com
Defective engine PWB copyir.com
2300 Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s copyir.com After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2500 Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective paper feed motor copyir.com
Defective engine PWB copyir.com
2550 Transfer motor error
After transfer motor is driven, the ready signal does not turn to L within 2 s copyir.com After transfer motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser motor copyir.com
Defective engine PWB copyir.com
2600 PF paper feed motor error
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2610 PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2640 SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SD paper feed motor copyir.com
Defective SD main PWB copyir.com
2650 SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective SM paper feed motor copyir.com
Defective SM main PWB copyir.com
2660 PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
2670 PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective PF paper feed motor copyir.com
Defective PF main PWB copyir.com
3100 Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective home position sensor copyir.com
Defective scanner motor copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3200 Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LED lamp PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3300 Optical system (AGC) error
After AGC, correct input is not obtained at CCD copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective exposure lamp
Defective CCD PWB copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3310 CIS AGC error After AGC, correct input is not obtained at CIS copyir.com Defective CIS copyir.com
Defective DPSHD PWB copyir.com
Defective DP relay PWB copyir.com
3500 Communication error between scanner and ASIC
An error code is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective ISC PWB copyir.com
Defective main PWB copyir.com
3600 Scanner sequence error Defective ISC PWB copyir.com
3700 Scanner device error CCD connector inserted incorrectly copyir.com
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com No response is received in 100 ms from AEF copyir.com Defective ISC PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Defective backup memory or PWB copyir.com
4001 Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 30 s copyir.com The polygon motor speed won’t stabilize within 10 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4011 Polygon motor steady-state error
After polygon motor is stabilized, the ready signal is at the H level for 15 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective polygon motor copyir.com
Defective engine PWB copyir.com
4101 BD initialization error
After polygon motor is driven, ASIC detects a BD error for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB copyir.com
Defective engine PWB copyir.com
4201 BD steady-state error
The BD signal is not detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PD PWB copyir.com
Defective engine PWB copyir.com
5101 Main high-voltage error
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower high-voltage board) copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective high voltage PWB
Defective engine PWB copyir.com
6000 Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up copyir.com The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 30 s in warming up after reached to 100° C/212 °F copyir.com A temperature of less than 80°C/176 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 100°C/ 212 °F after warming up copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6020 Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 1 copyir.com
Defective engine PWB copyir.com
6030 Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s copyir.com Except, the A/D value in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a low-temperature environment copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6040 Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 1 wire copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6050 Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 1 copyir.com
Defective fuser heater copyir.com
Defective engine PWB copyir.com
6100 Broken fuser heater wire
Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 5 wire copyir.com
Defective engine PWB copyir.com
6120 Abnormally high fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature higher than 190C/374F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 5 copyir.com
Defective engine PWB copyir.com
6130 Broken fuser thermistor 5 wire
Input from fuser thermistor 5 is 992 or more (A/D value) continuously for 60 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 5 wire copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6150 Abnormally low fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature lower than 30C/ 86F for 1 s after warming up copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 5 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6200 Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up copyir.com The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6220 Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 240C/464F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 2 copyir.com
Defective engine PWB copyir.com
6230 Broken fuser thermistor 2 wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D) continuously for 1 second during the temperature detected by the fuser thermistor 1 is 100 deg-C or more copyir.com Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 2 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6250 Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 100C/212F for 1 s during ready or print copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Defective fuser thermistor 2 copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6320 Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 215C/419F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 3 copyir.com
Defective engine PWB copyir.com
6330 Broken fuser thermistor 3 wire
Fuser thermistor 3 detects a temperature lower than 20C/ 68F continuously for 1 s Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin copyir.com
Defective triac copyir.com
Broken fuser thermistor 3 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6520 Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 215C/419F for 1 s copyir.com Deformed connector pin copyir.com
Defective triac copyir.com
Shorted fuser thermistor 4 copyir.com
Defective engine PWB copyir.com
6530 Broken fuser thermistor 4 wire
Fuser thermistor 4 detects a temperature lower than 20C/ 68F continuously for 1 s Defective connector cable or poor contact in the connector copyir.com
Deformed connector pin
Defective triac copyir.com
Broken fuser thermistor 4 wire copyir.com
Fuser thermostat triggered copyir.com
Defective fuser IH copyir.com
Defective engine PWB copyir.com
6600 Fuser belt rotation error
A belt rotating pulse is not received for 1 second copyir.com (Engine CPU) Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective engine PWB copyir.com
6610 Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective fuser release motor copyir.com
Defective engine PWB copyir.com
6620 IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective IH core motor copyir.com
Defective eject PWB copyir.com
Defective front PWB copyir.com
Defective engine PWB copyir.com
6710 Fuser IH PWB CPU reset error
Watch doc timer has been overflowed copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6720 Fuser IH belt rotation error
A belt rotating pulse is not received for 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser belt sensor copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6730 Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6740 Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6750 Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6760 Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6770 Fuser IH low electric power error
The preset power is less than 0 copyir.com6 times of it for 120 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6780 Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6900 Fuser belt cooling fan error
When the fuser front or rear fan motor is driven, alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser front or rear fan motor copyir.com
Defective engine PWB copyir.com
6940 IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective IH fan motor copyir.com
Defective engine PWB copyir.com
6950 Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU copyir.com A checksum error is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
6990 Fuser power supply incompatibility Information won’t match between the engine backup and the fuser IH PWB copyir.com Defective fuser IH PWB copyir.com
Defective engine PWB copyir.com
7001 Toner motor error
During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective toner motor copyir.com
Defective engine PWB copyir.com
7101 Toner sensor error
Sensor output value of 60 or less or 944 or more continued for 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective toner sensor copyir.com
Defective engine PWB copyir.com
7200 Broken outer temperature sensor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7210 Short-circuited outer temperature sensor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7221 Broken LSU thermistor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor copyir.com
Defective engine PWB copyir.com
7231 Short-circuited LSU thermistor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective LSU thermistor copyir.com
Defective engine PWB copyir.com
7241 Broken developer thermistor wire
The sensor input sampling is greater than 230 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor copyir.com
Defective engine PWB copyir.com
7251 Short-circuited developer thermistor
The sensor input sampling is less than 69 copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer thermistor copyir.com
Defective engine PWB copyir.com
7301 Toner hopper motor error
When the toner hopper motor is driven, toner hopper sensor does not turn on within 200 ms copyir.com This error is detected 15 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drive transmission system of motor copyir.com
Defective toner hopper sensor copyir.com
Defective toner hopper motor copyir.com
Defective engine PWB copyir.com
7401 Developer unit type mismatch error
Absence of the developer unit is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the developer unit is installed copyir.com
7411 Drum unit type mismatch error
Absence of the drum unit is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Different type of the drum unit is installed copyir.com
7460 Developer shutter error
Power is turned on while the developer shutter is locked copyir.com The developer shutter has been locked copyir.com
Defective connector cable or poor contact in the connector copyir.com
7601 ID sensor error Dark potential error
FrontDarkP and FrontDarkS are greater than 0 copyir.com80V copyir.com Light potential error FrontBrightS is smaller than FrontDarkS copyir.com FrontBrightP is smaller than FrontDarkP + 0 copyir.com5V Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7602 ID sensor error
Dark potential error RearDarkP and RearDarkS are greater than 0 copyir.com80V copyir.com Light potential error RearBrightS is smaller than RearDarkS copyir.com RearBrightP is smaller than RearDarkP + 0 copyir.com5V copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective engine PWB copyir.com
7800 Broken outer temperature sensor wire
The device did not respond for more than 5 ms during reading, in 5 times copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective outer temperature sensor copyir.com
Defective engine PWB copyir.com
7901 Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective drum PWB copyir.com
7911 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective developer unit copyir.com
7941 Laser scanner unit EEPROM error
Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective APC PWB copyir.com
8000 Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible copyir.com The finisher is installed with a device to which it is incompatible copyir.com
8010 Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch home position sensor copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8020 Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8030 Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch motor copyir.com
Defective PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF paddle sensor copyir.com
Defective DF paddle motor copyir.com
Defective DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF bundle discharge sensor copyir.com
Defective DF eject release motor copyir.com
Defective DF main PWB copyir.com
8110 DF shift motor 1 error (4000-sheet finisher)
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 1 copyir.com
Defective DF shift motor 1 copyir.com
Defective DF main PWB copyir.com
8120 DF shift motor 2 error (4000-sheet finisher)
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift sensor 2 copyir.com
Defective DF shift motor 2 copyir.com
Defective DF main PWB copyir.com
8130 DF shift release motor error (4000-sheet finisher) When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF shift release sensor copyir.com
Defective DF shift release motor copyir.com
Defective DF main PWB copyir.com
8140 DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8150 DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective sensor copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8160 DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF tray sensor 3 copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 1 copyir.com
Defective DF side registration motor 1 copyir.com
Defective DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 is detected twice copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF side registration sensor 2 copyir.com
Defective DF side registration motor 2 copyir.com
Defective DF main PWB copyir.com
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF staple sensor copyir.com
Defective DF slide motor copyir.com
Defective DF main PWB copyir.com
8230 DF staple motor error 1
Staple JAM (DF) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective DF staple sensor copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8240 DF staple motor error 2
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective DF staple motor copyir.com
Defective DF main PWB copyir.com
8250 DF tray motor error 4
The lock signal of the motor is detected continuously for 10 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DF tray motor copyir.com
Defective DF main PWB copyir.com
8300 Center-folding unit communication error (4000-sheet finisher)
Communication with the center-folding unit is not possible copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF set sensor copyir.com
Defective PWB copyir.com
8310 CF side registration motor 2 error (4000-sheet finisher)
When initial operation, CF side registration sensor 2 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 2 copyir.com
Defective CF side registration motor 2 copyir.com
Defective CF main PWB copyir.com
8320 CF adjustment motor error (4000-sheet finisher)
When initial operation, CF adjustment sensor does not turn on within 2 copyir.com5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF adjustment sensor 1, 2 copyir.com
Defective CF adjustment motor 1, 2 copyir.com
Defective CF main PWB copyir.com
8330 CF blade motor error (4000-sheet finisher)
When initial operation, CF blade sensor does not turn on within 3 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF blade sensor copyir.com
Defective CF blade motor copyir.com
Defective CF main PWB copyir.com
8340 CF staple motor error 1 (4000-sheet finisher)
Staple JAM (Folding unit) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective CF staple sensor copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8350 CF side registration motor 1 error (4000-sheet finisher)
When initial operation, CF side registration sensor 1 does not turn on within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CF side registration sensor 1 copyir.com
Defective CF side registration motor 1 copyir.com
Defective CF main PWB
8360 CF main motor error (4000-sheet finisher)
During driving the motor, lock signal is detected for 1 s continuously Defective connector cable or poor contact in the connector copyir.com
Defective CF main motor copyir.com
Defective CF main PWB copyir.com
8370 CF staple motor error 2 (4000-sheet finisher)
Staple JAM (DF) has been detected twice in a row copyir.com (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice copyir.com) Defective connector cable or poor contact in the connector copyir.com
Defective CF staple motor copyir.com
Defective CF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective slide sensor copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective punch slide motor copyir.com
Defective PWB copyir.com
8430 Punch unit communication error
Communication failed to be established after the punch unit was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8500 Mailbox communication error (4000-sheet finisher)
Communication failed to be established after the mailbox was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8510 MB conveying motor error 1 (4000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor copyir.com
Defective MB main PWB copyir.com
8520 MB conveying motor error 2 (4000-sheet finisher)
When standby operation, MB home position sensor does not turn off within 1 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective MB home position sensor copyir.com
Defective MB conveying motor
Defective MB main PWB copyir.com
8800 Document finisher communication error
Communication failed to be established after the document finisher was hooked up copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
8900 Document finisher backup error
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM copyir.com
Defective DF main PWB copyir.com
8930 Center-folding unit backup error (4000-sheet finisher)
Read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Improper installation EEPROM copyir.com
Defective CF main PWB copyir.com
9000 Document processor communication error
Communication with the document processor is not possible copyir.com Defective connector cable or poor contact in the connector
Defective PWB copyir.com
9010 Coin vender communication error
A communication error from coin vender is detected 10 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Data setup failure copyir.com
Defective coin vender control PWB copyir.com
Defective PWB copyir.com
9040 DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 1 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9050 DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP lift sensor 2 copyir.com
Defective DP lift motor copyir.com
Defective DP main PWB copyir.com
9060 DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively copyir.com Mismatch between writing data and reading data occurs 3 times successively copyir.com Defective DP main PWB copyir.com
Device damage of EEPROM copyir.com
9070 Communication error between DP and SHD
A communication error is detected copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DPSHD PWB copyir.com
9080 LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective CIS
Defective DPSHD PWB copyir.com
9100 Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB copyir.com Defective coin vender control PWB copyir.com
9110 Coin vender error
Communication error has been detected in connection with the coin mec and the rejector copyir.com Rejector installed incorrectly copyir.com
Defective rejector copyir.com
9120 Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9130 Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9140 Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9150 Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough copyir.com Coin jam in the change tube
Poor contact in the connector copyir.com
Defective change empty sensor copyir.com
Defective coin vender control PWB copyir.com
9160 Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active copyir.com Defective pay-out motor copyir.com
9170 Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active copyir.com Change jam at the pay-out copyir.com
Defective pay-out motor copyir.com
Defective pay-out sensor copyir.com
9200 DP multi feed sensor communication error
A communication error is detected 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective PWB copyir.com
9210 DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9220 DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession copyir.com Defective connector cable or poor contact in the connector copyir.com
Defective DP multi feed sensor copyir.com
Defective DP main PWB copyir.com
9500, 9510, 9520 Contact the Service Administrative Division copyir.com
F000 Communication error between main PWB and operation PWB Defective main PWB copyir.com
Defective operation PWB copyir.com
F010 Main PWB checksum error Defective main PWB copyir.com
F040 Communication error between main PWB and print engine Defective main PWB copyir.com
Defective engine PWB copyir.com
F041 Communication error between main PWB and scanner engine Defective main PWB copyir.com
Defective ISC PWB copyir.com
F050 Print engine ROM checksum error Defective engine PWB copyir.com
F051 Scanner engine ROM checksum error Defective ISC PWB copyir.com
F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.