درایور فتوکپی ریکو MP 3353
1404-08-05
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
0030 FAX control PWB system error
Processing with the fax software was disabled due to a software problem copyir.com FAX control PWB
0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted copyir.com FAX control PWB (The FAX PWB installed will not be the one designed for the machine copyir.com)
0100 Backup memory device error EEPROM(main PWB)
0120 MAC address data error
For data in which the MAC address is invalid copyir.com EEPROM(main PWB)
0130 Backup memory read/write error (main PWB)
Mismatch between writing data and reading data successively copyir.com Main PWB
0140 Backup memory data error (main PWB) When the data read from NAND is abnormalities copyir.com Main PWB
0150 Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively copyir.com Mismatch of reading data from 2 locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com EEPROM (Engine PWB)
0160 Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal copyir.com EEPROM
0170 Billing counting error
The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter copyir.com EEPROM copyir.com Main PWB copyir.com Engine PWB copyir.com
0180 Machine number mismatch
Machine number of main and engine does not match copyir.com Data damage of EEPROM copyir.com
0350 Panel PWB communication error (electronic volume I2C communication error
NACK is received during I2C communication – retried 5 times – rebooting command sent – retried 5 times If NACK is still received copyir.com Operation PWB copyir.com Main PWB
0620 FAX image DIMM error
1 copyir.com The Fax image DIMM has not been installed copyir.com 2 copyir.com Fax image DIMM access error copyir.com FAX image DIMM copyir.com Main PWB copyir.com
0630 DMA error
DMA transmission of image data does not complete within the specified period of time copyir.com DP CIS copyir.com DP main PWB Main PWB copyir.com
0640 Hard disk error
The hard disk cannot be accessed copyir.com HDD copyir.com Main PWB copyir.com
0650 FAX image DIMM check error
A fax image DIMM which was used with another machine is installed copyir.com FAX DIMM copyir.com Main PWB
0660 Hard disk encryption key error EEPROM copyir.com HDD copyir.com Main PWB
0670 Hard disk overwriting erasure error HDD copyir.com Main PWB copyir.com
0800 Image processing error
JAM010X is detected twice copyir.com Main PWB copyir.com
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB copyir.com FAX software copyir.com FAX control PWB copyir.com
0840 Faults of RTC
(“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state copyir.com The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM) copyir.com The RTC setting is older than 00:01 on January 1, 2000 copyir.com [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked copyir.com 10 minutes have been passed since the previous check copyir.com After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T copyir.com’ Battery ( main PWB) copyir.com Main PWB copyir.com
0870 PCFAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times copyir.com FAX control PWB copyir.com HDD copyir.com Main PWB copyir.com
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB copyir.com FAX control PWB copyir.com
0980 24 V power down detect
If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second copyir.com Power source PWB copyir.com
1010 Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 15 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Cassette lift base elevating mechanism copyir.com Lift motor 1 copyir.com Lift sensor 1 copyir.com Engine PWB copyir.com
1020 Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 15 s copyir.com This error is detected 5 times successively copyir.com The lock signal of the motor is detected continuously for 1 s copyir.com This error is detected 5 times successively copyir.com Cassette lift base elevating mechanism copyir.com Lift motor 2 copyir.com Lift sensor 2 copyir.com Engine PWB copyir.com
1030 PF lift motor 1 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism copyir.com PF Lift motor 1 copyir.com PF Lift sensor 1 copyir.com PF main PWB copyir.com
1040 PF lift motor 2 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 15 s copyir.com This error is detected 5 times successively copyir.com During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after motor is turned on is excluded from detection copyir.com Cassette lift base elevating mechanism copyir.com PF Lift motor 2 copyir.com PF Lift sensor 2 copyir.com PF main PWB copyir.com
1100 PF lift motor 1 error (large capacity feeder)
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after PF lift motor 1 is turned on is excluded from detection copyir.com Paper feeder lift base elevating mechanism copyir.com PF Lift motor1 copyir.com PF Lift sensor1 copyir.com PF main PWB copyir.com
1110 PF lift motor 2 error (large capacity feeder)
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s copyir.com This error is detected 5 times successively copyir.com (Time to detect is 2 seconds at the second time and later copyir.com) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively copyir.com However, the first 1 s after PF lift motor 2 is turned on is excluded from detection copyir.com Paper feeder lift base elevating mechanism copyir.com PF Lift motor 2 copyir.com PF Lift sensor2 copyir.com PF main PWB copyir.com
1800 Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession copyir.com Paper feeder copyir.com PF main PWB copyir.com Engine PWB copyir.com
1900 Paper feeder EEPROM error
When writing the data, read and write data does not match 4 times in succession copyir.com PF main PWB (EEPROM)
2010 Main motor startup error
Main motor is not stabilized within 1 s since the motor is activated copyir.com Main motor copyir.com Engine PWB copyir.com
2200 Main motor steady-state error
After main motor is stabilized, the ready signal is at the H level for 2 s continuously copyir.com Main motor copyir.com Engine PWB copyir.com
2500 Paper feed motor steadystate error
The rated speed signal detected the stability OFF continuously for 2 s after the paper feed motor stabilizes copyir.com Paper feed motor copyir.com Engine PWB copyir.com
2510 Paper feed motor startup error
Paper feed motor is not stabilized within 1 s since the motor is activated copyir.com Paper feed motor copyir.com Engine PWB copyir.com
2600 PF drive motor error (paper feeder)
After PF drive motor is driven, the ready signal does not turn to L within 2 s copyir.com PF drive motor copyir.com PF main PWB copyir.com
2610 PF drive motor error (large capacity feeder)
After PF drive motor is driven, the ready signal does not turn to L within 2 s copyir.com PF drive motor copyir.com PF main PWB copyir.com
3100 Scanner carriage error
ON/OFF of the HP sensor doesn’t change after a prescribed pulse passes from power supply ON copyir.com The scanner mirror frame is being locked after setup copyir.com Scanner motor copyir.com Home position sensor copyir.com ISC PWB copyir.com Main PWB copyir.com
3210 CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s copyir.com CIS copyir.com DPSHD PWB copyir.com DP relay PWB copyir.com
3220 LED error
The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 200 copyir.com It is 1000 or more at the time of market mode copyir.com CIS copyir.com ISC PWB copyir.com Main PWB copyir.com
3300 Optical system (AGC) error
When the value of a gain becomes more than FF or 89 or less at least one at the AGC processing instruction execution time for CCD lamps copyir.com LED lamp PWB copyir.com CCD PWB copyir.com ISC PWB copyir.com Main PWB copyir.com
3310 CIS AGC error
One of the gains is FF during the CCD lamp AGC is being processed copyir.com CIS copyir.com DPSHD PWB copyir.com
3500 Communication error between scanner and ASIC A wrong read-back value copyir.com ISC PWB copyir.com Main PWB copyir.com
3600 Scanner sequence error ISC PWB
3700 Scanner device error CCD (ISU)
3800 AFE error
When writing the data, read and write data does not match 3 times in succession copyir.com ISC PWB copyir.com CCD PWB copyir.com
3900 Backup memory read/write error (ISC PWB)
Read and write data does not match copyir.com Backup memory (ISC PWB)
4001 Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 10 s copyir.com Polygon motor (LSU) copyir.com Engine PWB copyir.com
4011 Polygon motor steady-state error
After Polygon motor is stabilized, the ready signal is at the H level for 1 s continuously copyir.com Polygon motor (LSU) copyir.com Engine PWB copyir.com
4101 BD initialization error
After Polygon motor is driven, the BD signal is not detected for 1 s copyir.com PD PWB (LSU) copyir.com Engine PWB copyir.com
4201 BD steady-state error
The BD signal is not detected copyir.com PD PWB (LSU) copyir.com Engine PWB copyir.com
5101 Main high-voltage error
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 5 copyir.com Drum unit copyir.com Charger roller unit PWB) copyir.com High voltage PWB copyir.com Engine PWB copyir.com
6020 Abnormally high fuser thermistor 2 temperature
Input from fuser thermistor 2 is abnormal value continuously for 1 s copyir.com Fuser unit copyir.com Fuser thermistor 2 copyir.com Engine PWB copyir.com
6030 Broken fuser thermistor 2 wire
A/D value of the fuser thermistor 2 exceeds 251 bit continuously for 5 copyir.com6 s during warming up copyir.com Fuser unit copyir.com Fuser thermistor 2 copyir.com Engine PWB copyir.com
6200 Broken fuser edge heater wire
Even if 60 seconds pass after a warm-up start, when it will not be in a stable state copyir.com When the difference in temperature 5 copyir.com6 seconds and 16 seconds after heater lighting is less than 43 °C copyir.com Even if 8 seconds pass during test mode operation, when change of AD is less than three copyir.com Fuser unit copyir.com Fuser thermostat copyir.com Fuser heater copyir.com Powe source PWB copyir.com Engine PWB copyir.com
6220 Abnormally high fuser edge thermistor temperature
Input from fuser thermistor 1 is abnormal value continuously for 1 s copyir.com Fuser unit copyir.com Fuser thermistor 1 copyir.com Engine PWB copyir.com
6230 Broken fuser edge thermistor wire
A/D value of the fuser thermistor 1 exceeds 251 bit continuously for 5 copyir.com6 s during warming up Fuser unit1 copyir.com Fuser thermistor 1 copyir.com Engine PWB copyir.com
6250 Abnormally low fuser edge thermistor temperature
When the detection temperature of the fixing thermistor 1 is falling target temperature by 75 °C or more for 1 second after secondary stable temperature attainment copyir.com Fuser unit copyir.com Fuser thermostat copyir.com Fuser heater copyir.com Engine PWB copyir.com
6400 Zero-cross signal error
While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s copyir.com Fuser unit copyir.com
6910 Engine software ready error
The device won’t engage in ready state in 60 minutes after warming-up has began copyir.com (A previous timeout process has not been cancelled copyir.com) Engine PWB copyir.com
7200 Broken outer temperature sensor 2 wire
The sensor input sampling is greater than 244 copyir.com BD PWB copyir.com Engine PWB copyir.com
7210 Short-circuited outer temperature sensor
The temperature sensor input sampling is less than 10 copyir.com BD PWB copyir.com Engine PWB copyir.com
7800 Broken outer temperature sensor wire
The temperature sensor input sampling is more than 237F Thermistor PWB copyir.com Engine PWB copyir.com
7810 Short-circuited external thermistor wire external thermistor delivers 3V or more copyir.com Thermistor PWB copyir.com Engine PWB copyir.com
7901 Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Drum unit copyir.com Engine PWB copyir.com
7911 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively copyir.com Mismatch of reading data from two locations occurs 8 times successively copyir.com Mismatch between writing data and reading data occurs 8 times successively copyir.com Developer unit copyir.com Engine PWB copyir.com
8010 Punch motor 1 error
When the punch motor is driven, punch home position sensor does not turn on within 200 ms Punch motor copyir.com Punch home position sensor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8020 Punch motor 2 error
Home position is not obtained in 3 s after home position is initialized or in standby copyir.com Punch motor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8030 Punch motor 3 error
Home position does not turn from On to Off in 50 ms after home position has been initialized copyir.com Punch motor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8090 DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s copyir.com DF paddle motor copyir.com DF paddle sensor copyir.com DF main PWB copyir.com
8100 DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s copyir.com DF eject release motor DF bundle discharge unit sensor copyir.com DF bundle discharge unit sensor copyir.com DF main PWB copyir.com
8110 DF shift motor 1 error (3000-sheet finisher)
DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven copyir.com DF shift motor 1 [front] copyir.com DF shift sensor 1 [front] copyir.com DF main PWB copyir.com
8120 DF shift motor 2 error (3000-sheet finisher)
DF shift sensor 2 won’t turn on when it has travelled 160 mm after DF shift motor 2 is driven copyir.com DF shift motor 2 [rear] copyir.com DF shift sensor 2 [rear] copyir.com DF main PWB copyir.com
8130 DF shift release motor error (3000-sheet finisher)
When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s copyir.com DF shift release motor copyir.com DF shift release sensor copyir.com DF main PWB copyir.com
8140 DF tray error 1
When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s copyir.com DF tray motor copyir.com DF tray sensor 1 copyir.com DF tray upper surface sensor copyir.com DF main PWB copyir.com
8150 DF tray error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s copyir.com DF tray motor copyir.com DF tray sensor 1 copyir.com DF tray upper surface sensor copyir.com DF main PWB copyir.com
8160 DF tray error 3
When the main tray has descended, DF tray sensor 4 does not turn on within 20 s copyir.com DF tray motor copyir.com DF tray sensor 4 copyir.com DF main PWB copyir.com
8170 DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s copyir.com DF side registration motor 1 copyir.com DF side registration sensor 1 copyir.com DF main PWB copyir.com
8180 DF side registration motor 1 error 2
JAM6810 ( jam in front of width alignment) is detected twice copyir.com DF side registration motor 1 copyir.com DF side registration sensor 1 copyir.com DF main PWB copyir.com
8190 DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s copyir.com DF side registration motor 2 copyir.com DF side registration sensor 2 copyir.com DF main PWB copyir.com
8200 DF side registration motor 2 error 2
JAM6910 ( jam in rear of width alignment) is detected twice copyir.com DF side registration motor 2 copyir.com DF side registration sensor 2 copyir.com DF main PWB
8210 DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s copyir.com DF slide motor copyir.com DF staple sensor copyir.com DF main PWB copyir.com
8230 DF staple motor error 1
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven copyir.com) DF staple motor copyir.com DF staple sensor copyir.com DF main PWB copyir.com
8240 DF staple motor error 2
Staple JAM (DF) has been detected twice in a row copyir.com (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven copyir.com) DF staple motor copyir.com DF main PWB copyir.com
8260 DF middle motor error
When the DF middle motor is driven, DF middle sensor does not turn on within 1s copyir.com DF middle motor copyir.com DF middle sensor copyir.com DF main PWB copyir.com
8410 Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm copyir.com Punch slide motor copyir.com Punch slide sensor copyir.com Punch PWB copyir.com DF main PWB copyir.com
8420 Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move copyir.com Punch slide motor copyir.com Punch paper edge sensor 1,2 copyir.com Punch PWB copyir.com DF main PWB copyir.com
8430 Punch unit communication error
Communication with the punch unit is not possible copyir.com Punch PWB copyir.com DF main PWB copyir.com
8500 Mailbox communication error (3000-sheet finisher)
Communication failed to be established after the mailbox was hooked up copyir.com MB main PWB copyir.com DF main PWB copyir.com
8510 MB conveying motor error 1 (3000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s copyir.com MB conveying motor copyir.com MB home position sensor copyir.com MB main PWB copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.