اپسون Epson AcuLaser C1100

C0017    CPU error (undefined interruption)
C0081    CPU error (TLB modification exception)
C0082    CPU error (TLB miss exception [Load/Fetch])
C0083    CPU error (TLB miss exception [Store])
C0084    CPU error (address error exception [Load/Fetch])
C0085    CPU error (address error exception [Store])
C0086    CPU error (bus error exception [Fetch])
C0087    CPU error (bus error exception [Load/Store])
C0088    CPU error (SYSCALL exception)
C0089    CPU error (Break exception)
C0090    CPU error (reserving command exception)
C0091    CPU error (unused coprocessor exception)
C0092    CPU error (FPU exception)
C0093    CPU error (TLB exception)
C0094    CPU error (XTLB exception)
C0095    CPU error (cache exception)
C0096    CPU error (Trap exception)
C0097    CPU error (FPU exception)
C0098    CPU error (watch exception)
C0128       copyir.com      copyir.com      copyir.com C0254    CPU error (undefined trap)
C0255    CPU error (NMI exception)
C0256    CPU error (divide by 0)
C0257    CPU error (arithmetic overflow)
C0258    CPU error (break occurrence)
C0800    IPL error (controller defect)
C0998    Engine communication error (only when power-on)
C0999    Engine flash ROM has no program data
C1002    Standard RAM error (standard size is undefined, etc      copyir.com)
C1010    Verification error
C1020    RAM error (slot 0)
C1021    RAM error (slot 1)
C1120    ROM checksum error (bit 0 to 7) (program)
C1121    ROM checksum error (bit 8 to 15) (program)
C1122    ROM checksum error (bit 16 to 23) (program
C1123    ROM checksum error (bit 24 to 31) (program)
C1200    EEPROM writing error
C1210    EEPROM writing times limit
C1400    Engine initialization error
C1500    CCNV hardware error
C1550    Initialization hardware error for SRAM for compression
C1600    Video series hardware error (including PWM IC calibration error)
C1800    Illegal SPD
C1999    Other hardware errors
C2000    Software error
E510    ROS Motor Failure
– PWBA MCU could not receive signals output from SOS Sensor in ROS within the specified time      copyir.com
E511    TR0 Failure
– PWBA MCU could not receive signals output from SENSOR TR-0 (TR0 Sensor) at the specified timing      copyir.com
E513    NVRAM Error
– An error occurred in NVRAM on PWBA MCU      copyir.com
E514    PAGE Timeout
– The PAGEC/PAGE signal was not received within 60sec after transmitting PFA      copyir.com
E516    Communication Error Duplex
– A communication error occurred between PWBA MCU and Duplex      copyir.com
E517    Communication Error Feeder
– A communication error occurred between PWBA MCU and Feeder      copyir.com
E520    BTR 2 Advance Error
– The 2nd BTR Retract Sensor does not turn ON within the specified time      copyir.com
E521    BTR 2 Error
– The input of 2nd BTR Retract Sensor does not change when 2nd BTR is initialized      copyir.com
E523    PCDC Error
– PCDC is not functioning normally      copyir.com
E524    Low Density
– The output value of SENSOR ASSY ADC (ADC Sensor) is below the specified value      copyir.com
E525    High Density
– The output value of SENSOR ASSY ADC (ADC Sensor) exceeds the specified value      copyir.com
E526    ADC Contamination
– SENSOR ASSY ADC (ADC Sensor) error
E527    Deve Home Position Sensor Error
– PWBA MCU could not receive signals output from Rotary Home Position Sensor within the specified time after rotation of Rotary 45 (p      copyir.com198) Developer      copyir.com
E530    Humidity Sensor Error
– When the Input from SENSOR HUM & TEMP is out of specification      copyir.com
E533    Temp Sensor Error
– SENSOR HUM & TEMP detected a temperature below -7°C or over 55°C      copyir.com
E537    Fuser Fail
– Control Thermistor detected a temperature exceeding the specified temperature      copyir.com Safety Thermistor detected a temperature exceeding the specified temperature      copyir.com
– The Control Thermistor did not detect a Ready even though the specified time elapsed from Main Lamp ON at Warm Up      copyir.com
– The Main Lamp continues to stay lit even after time specified for the Main Lamp elapsed after the Control Thermistor detected a Ready      copyir.com
– The Control Thermistor detected a temperature below the specified temperature even after the specified time elapsed from Main Lamp ON at Warm Up      copyir.com
– The latch lever of FUSER ASSY is set incorrectly      copyir.com
E542    IBT CLN Fail
– SENSOR IBT RETRACT cannot detect Advance/Retract of CAM ASSY-IBT CL      copyir.com
E546    Duplex Motor Failure
– The MOTOR ASSY DUP (Lower Roll Motor) or MOTOR ASSY DUP INV (Upper Roll Motor) of Duplex is not rotating at the 57 specified speed      copyir.com
E547    Feed Motor Failure
– DRIVE ASSY FEED (Feed Motor) of the Feeder is not rotating at the specified speed      copyir.com
E998    Engine Communication Error
– Acommunication error between the controller and the PWBA MCU via the video I/F occured