توشیبا Toshiba 3910
1404-08-13
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
E000-0000 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor is less than 70 deg C 3 copyir.ocm5 min after power on copyir.ocm Check the mounting/soiling of the main thermistor copyir.ocm Replace the fixing heater copyir.ocm Replace the main thermistor copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E000-0010 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E001-0001 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR) copyir.ocm
The reading of the main thermistor or the sub thermistor is 230 deg C or more for 2 sec copyir.ocm (hardware detection) Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E001-0002 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR) copyir.ocm
The reading of the main thermistor or the sub thermistor is 230 deg C or more for 2 sec or more copyir.ocm (software detection) Check the mounting/soiling of the main thermistor copyir.ocm Replace the main thermistor copyir.ocm Replace the sub thermistor copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E001-0003 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR) copyir.ocm
The difference in the readings of the main thermistor and the sub thermistor is 50 deg C for 1 sec copyir.ocm (main thermistor reading>sub thermistor reading) Check the mounting/soiling of the main thermistor copyir.ocm Replace the main thermistor copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E001-0004 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR) copyir.ocm
The difference in the readings of the main thermistor and the sub thermistor is 50 deg C for 1 sec or more copyir.ocm (main thermistor reading>/=sub thermistor reading) Check the mounting/soiling of the main thermistor copyir.ocm Replace the main thermistor copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E001-0010 The fixing unit has overheated copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR) copyir.ocm
The power has been turned off and then on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E002-0000 The fixing unit has overheated copyir.ocm After correcting the error, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 70 deg C, but does not reach 100 deg C within 2 copyir.ocm5 sec thereafter copyir.ocm Disconnect and then connect J508 of the DC controller PCB copyir.ocm Disconnect and then connect the connectors of the fixing unit copyir.ocm Check the wiring between the main/sub thermistor and the DC controller copyir.ocm Check the mounting/soiling of the main thermistor copyir.ocm Replace the fixing heater copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E002-0001 The fixing unit has overheated copyir.ocm After correcting the error, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 100 deg C, but does not reach 150 deg C within 2 copyir.ocm5 min thereafter) Disconnect and then connect J508 of the DC controller PCB copyir.ocm Disconnect and then connect the connectors of the fixing unit copyir.ocm Check the wiring between the main/sub thermistor and the DC controller copyir.ocm Check the mounting/soiling of the main thermistor copyir.ocm Replace the fixing heater copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E002-0010 The fixing unit has overheated copyir.ocm After correcting the error, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E003-0000 The fixing unit temperature is abnormally low copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The reading of the main thermistor has exceeded 100 deg C, but is 70 deg C or less for 2 sec thereafter copyir.ocm Disconnect and then connect J508 of the DC controller PCB copyir.ocm Disconnect and then connect the connectors of the fixing unit copyir.ocm Check the wiring between the main/sub thermistor and the DC controller PCB copyir.ocm Check the mounting/soiling of the main thermistor copyir.ocm Replace the fixing heater copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E004-0000 The fixing unit has a fault copyir.ocm (protective circuit ON) After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
While the sub heater is on, the SSR for the heater drive has a short-circuit for 5 sec or more copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E004-0001 The fixing unit has a fault copyir.ocm (protective circuit ON) After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
While the main heater is on, the SSR for the heater drive has a short-circuit for 5 sec or more copyir.ocm Replace the AC driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E005-0000 The fixing web has run out copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of the fixing web has been detected for 5 sec or more copyir.ocm Check the position of the fixing web detecting lever copyir.ocm Replace the fixing web copyir.ocm Replace the fixing web length sensor copyir.ocm Replace the DC controller PCB copyir.ocm If you have replaced the fixing web, be sure to reset the counter: – COPIER>COUNTER>MISC>FIX-WEB – COPIER>COUNTER>DRBL-1>FX-WEB
E005-0010 The fixing web has run out copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E010-0000 The main motor rotation is faulty copyir.ocm
After the main motor has gone on, the FG signal of the motor is not detected for 2 sec or more copyir.ocm Disconnect and then connect J611 and J612 of the main motor copyir.ocm Disconnect and then connect J514 of the DC controller PCB copyir.ocm Disconnect and then connect J1720 of the relay PCB copyir.ocm Replace the main motor copyir.ocm Replace the relay PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E012-0000 The drum motor rotation is faulty copyir.ocm
After the drum motor has gone on, the PLL lock signal of the motor is not detected for 2 sec or more copyir.ocm Disconnect and then connect J1721 of the relay PCB copyir.ocm Disconnect and then connect J512 of the DC controller PCB copyir.ocm Disconnect and then connect J601 and J602 of the drum motor copyir.ocm Replace the drum motor copyir.ocm Replace the DC controller PCB copyir.ocm
E013-0000 The waste toner feedscrew is stuck copyir.ocm (clogged with waste toner) After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The waste toner feedscrew is stuck for 4 sec or more copyir.ocm Detach and then attach the waste toner pipe copyir.ocm Replace the waste toner pipe copyir.ocm Replace the waste toner feedscrew detecting switch copyir.ocm Replace the DC controller PCB copyir.ocm
E013-0010 The waste toner feedscrew is stuck copyir.ocm (clogged with waste toner) After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E014-0000 The fixing motor rotation is faulty copyir.ocm
After the fixing motor has gone on, the PLL signal of the motor is not detected for 2 sec or more copyir.ocm Disconnect and then connect J651 and J652 of the fixing motor copyir.ocm Replace the fixing motor copyir.ocm Replace the relay PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E015-0000 The pickup motor rotation is faulty copyir.ocm
The pickup motor has gone on, but the FG signal of the motor is not detected for 2 sec or more copyir.ocm Disconnect and then connect J621 and J622 of the pickup motor copyir.ocm Replace the pickup motor copyir.ocm Replace the relay PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E019-0000 The waste toner case is full copyir.ocm
After the waste toner case has become full, 50,000 prints (A4) or more have been made without disposing of the waste toner copyir.ocm Dispose of the waste toner copyir.ocm Check the operation of the waste toner bottle base copyir.ocm Disconnect and then connect J514 of the DC controller PCB copyir.ocm Replace the waste toner case full sensor copyir.ocm Replace the DC controller PCB copyir.ocm
E020-0001 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside the developing assembly is detected of 120 sec or more even when toner supply operation has been executed for the assembly copyir.ocm Disconnect and then connect the connector (J504, J512) of the DC controller PCB copyir.ocm Replace the developing cylinder clutch (CL4) copyir.ocm Replace the buffer motor (M18) copyir.ocm Replace the magnet roller drive clutch (CL1) copyir.ocm
E020-0002 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner in the buffer is detected for 60 sec even after toner supply operation for the buffer has been executed and when there is toner inside the hopper copyir.ocm Disconnect and connect the connector (J504, J511) of the DC controller PCB copyir.ocm Replace the buffer motor (M18) copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2) copyir.ocm
E020-0003 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside the buffer is detected for 210 sec or more even when there is toner inside the sub hopper and after toner supply operation of that buffer following the replacement of the toner bottle copyir.ocm Disconnect and connect the connector (J504, J511) of the DC controller PCB copyir.ocm Replace the buffer motor (M18) copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2) copyir.ocm
E020-0004 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The absence of toner inside he buffer is detected for 150 sec or more even when there is toner inside the buffer and after toner supply operation has been executed for the buffer following the replacement of the toner bottle copyir.ocm Disconnect and connect the connector (J504, J511) of the DC controller PCB copyir.ocm Replace the buffer motor (M18) copyir.ocm Replace the following: magenta roller drive clutch (CL1), toner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1), buffer inside toner lower limit sensor (TS2) copyir.ocm
E020-0005 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is executed, the developing assembly inside toner sensor does not detect the presence of toner Disconnect and then connect the connector (J504) of the DC controller PCB copyir.ocm Replace the developing assembly inside toner sensor (TS3) copyir.ocm
E020-0006 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installation mode (COPIER>FUNCTION>INSTALL>TONER-S) is executed, the developing assembly inside toner sensor detects the presence of toner, but it does not detect the presence for 600 sec or more thereafter copyir.ocm Disconnect and then connect the connector (J504) of the DC controller PCB copyir.ocm Replace the developing assembly inside toner sensor (TS3) copyir.ocm
E020-0007 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When installing mode (COVER>FUNCTION>INSTALL>TONER-S) is executed, the buffer inside toner sensor does not detect the presence of toner for 60 sec or more copyir.ocm Disconnect and connect the connector (J504, J511) of the DC controller PCB copyir.ocm Replace thetoner transport motor (sub hopper; M22), toner transport clutch (sub hopper; CL23), buffer inside toner sensor (TS1) copyir.ocm
E020-0008 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
When the toner feed motor (sub hopper) is driven, a fault is detected for 3 sec or more for the motor copyir.ocm Disconnect and connect the connector (J511) of the DC controller PCB copyir.ocm Replace the toner feed motor (sub hopper; M22) copyir.ocm
E020-0009 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
There is a fault in the rotation of the buffer motor copyir.ocm Disconnect and then connect the connector (J504) of the DC controller PCB copyir.ocm Replace the buffer motor (M18) copyir.ocm
E020-0010 The developing assembly is out of toner copyir.ocm The buffer motor rotation is faulty copyir.ocm The toner feed motor (sub hopper) rotation is faulty copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The power has been turned off and then on without resetting the error copyir.ocm Reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
E025-0000 The toner bottle motor rotation is faulty copyir.ocm
A toner bottle motor error (over-current) is detected for 10 sec for a second time copyir.ocm MEMO: The 1st detection of the error will cause the machine to indicate the message “Shake and Replace the Toner Container copyir.ocm” Disconnect and then connect J512 of the DC controller PCB copyir.ocm
E025-0001 The toner bottle motor rotation is faulty copyir.ocm
The toner bottle motor is not connected copyir.ocm Disconnect and then connect J512 of the DC controller PCB copyir.ocm
E032-0001 The copy data controller/NE controller counter fails to operate copyir.ocm
An open circuit of the counter signal has been detected copyir.ocm Disconnect and then connect J1022 of the main controller PCB copyir.ocm Replace the copy data controller/NE controller copyir.ocm Replace the main controller PCB copyir.ocm
E043-0000 The rotation of the pickup motor of the side paper deck is faulty copyir.ocm
The side paper deck pickup motor has gone on, but the PLL lock signal is not detected for 2 sec or more (1st detection) copyir.ocm MEMO: For the 2nd and subsequent detection, the machine will indicate “E043” on the screen offering a choice of sources of paper copyir.ocm Disconnect and then connect J101 and J106 of the side paper deck driver PCB copyir.ocm Replace the pickup motor copyir.ocm Replace the side paper deck driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E051-0001 The horizontal registration HP detection has an error copyir.ocm
After the start of horizontal registration HP detection, the HP sensor is not off within 5 sec (i copyir.ocme copyir.ocm, not leaving home position) copyir.ocm MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam copyir.ocm At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec copyir.ocm
E051-0002 The horizontal registration HP detection has an error copyir.ocm
After the start of horizontal registration HP detection, the home position is not detected within 5 sec copyir.ocm MEMO: If an error is detected in the course of horizontal registration HP detection at power-on, the machine will indicate the presence of a jam copyir.ocm At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec copyir.ocm
E051-0003 The horizontal registration HP detection has an error copyir.ocm
Replace the horizontal registration HP sensor copyir.ocm Replace the horizontal registration motor copyir.ocm Replace the stackless transport driver PCB copyir.ocm Replace the DC controller PCB copyir.ocm At the start of horizontal registration detection in the course of printing, the horizontal registration detection operation for downstream paper does not end within 5 sec copyir.ocm
E065-0000 The high-voltage output has a fault copyir.ocm (primary charging assembly)
A fault (leak) is detected when high voltage is supplied to the primary charging assembly copyir.ocm Remove and then mount the primary charging assembly copyir.ocm Check for soiling copyir.ocm Disconnect and then connect T601, J723, and J731 of the HV-DC PCB copyir.ocm Replace the HV-DC PCB copyir.ocm
E067-0000 The high-voltage output has a fault copyir.ocm
A fault is detected at the same time in 2 of the following: primary high voltage, pre-transfer high voltage, transfer high voltage, separation high voltage copyir.ocm Remove and mount the primary charging assembly copyir.ocm Remove and mount the pre-transfer charging assembly copyir.ocm Remove and mount the transfer/ separation charging assembly copyir.ocm Disconnect and then connect J721, J723, J731, and J734 of the HV-DC PCB copyir.ocm Replace the HV-DC PCB copyir.ocm Replace the HV-AC PCB copyir.ocm
E068-0000 The high-voltage output has a fault copyir.ocm (separation charging assembly)
A fault (leak) has been detected while the separation charging assembly is being supplied with high voltage copyir.ocm Remove and mount the transfer/separation charging assembly copyir.ocm Disconnect and then connect J7233 and J734 of the HV-DC PCB copyir.ocm Disconnect and then connect J741 and J742 of the HV-AC PCB copyir.ocm Replace the HV-AC PCB copyir.ocm Replace the transfer/ separation charging assembly copyir.ocm Replace the pre-transfer charging assembly copyir.ocm
E069-0000 The transfer high voltage has an error copyir.ocm
A fault (leak) has been detected while the transfer charging assembly is being supplied with high voltage copyir.ocm Remove and mount the transfer/separation charging assembly copyir.ocm Check for soiling copyir.ocm Disconnect and then connect T701 and J723 of the HV-DC PCB copyir.ocm Replace the HV-DC PCB copyir.ocm Replace the pre-transfer charging assembly copyir.ocm
E102-0001 A read error has occurred in relation to the laser scanner unit EEPROM data copyir.ocm
The correction data cannot be read from the EEPROM of the laser scanner unit copyir.ocm Disconnect and then connect the connector of the video PCB copyir.ocm Disconnect and then connect the DC controller PCB copyir.ocm Replace the laser scanner unit copyir.ocm
E110-0000 The laser scanner motor rotation has a fault copyir.ocm
After the laser scanner motor has gone on, the PLL lock signal of the motor is not detected for 15 sec or more copyir.ocm Check to see if all covers have been attached to the primary charging assembly copyir.ocm Disconnect and then connect J764 of the laser scanner motor drive PCB (in the laser scanner unit) copyir.ocm Disconnect and then connect J1401 of the video PCB copyir.ocm Disconnect and then connect J506 of the DC controller PCB copyir.ocm Replace the laser scanner unit copyir.ocm Replace the video PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E111-0000 The laser scanner motor cooling fan rotation has a fault copyir.ocm
After the laser scanner motor cooling fan has gone on, the fan stop signal is detected for 5 sec or more copyir.ocm Disconnect and then connect J503 of the DC controller PCB copyir.ocm Replace the laser scanner motor cooling fan copyir.ocm Replace the DC controller PCB copyir.ocm
E121-0001 A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2 copyir.ocm
The laser scanner unit cooling fan has a fault copyir.ocm After the laser scanner unit cooling fan has gone on, the fan stop signal is detected for 5 sec or more copyir.ocm Disconnect and then connect J503 of the DC controller PCB copyir.ocm Replace the laser scanner unit cooling fan copyir.ocm Replace the DC controller PCB copyir.ocm
E121-0002 A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2 copyir.ocm
The reader heat discharge fan 1 has a fault copyir.ocm After the reader heat discharge fan 1 has gone on, the fan stop signal is detected for 5 sec or more copyir.ocm Connect and then disconnect J512 of the DC controller PCB copyir.ocm Replace the reader heat discharge fan 1 copyir.ocm Replace the DC controller PCB copyir.ocm
E121-0003 A fault exists in the rotation of the following: laser scanner unit cooling fan, reader heat discharge fan 1, reader heat discharge fan 2 copyir.ocm
The reader heat discharge fan 2 has a fault copyir.ocm After the reader heat discharge fan 2 has gone on, the fan stop signal is detected for 5 sec or more copyir.ocm Disconnect and then connect J521 of the DC controller PCB copyir.ocm Replace the reader heat discharge fan 2 copyir.ocm Replace the DC controller PCB copyir.ocm
E197-0000 The laser scanner motor communication has a fault copyir.ocm
The communication with the laser control IC is not normal copyir.ocm Replace the laser scanner unit copyir.ocm Replace the video PCB copyir.ocm
E202-0001 The scanner HP detection mechanism has a fault copyir.ocm
At time of shading, the intensity of light is below the standard level copyir.ocm Disconnect and then connect the connector of the scanner HP sensor copyir.ocm Replace the scanner HP sensor copyir.ocm Replace the scanner motor copyir.ocm Replace the reader controller PCB copyir.ocm
E202-0002 The scanner HP detection mechanism has a fault copyir.ocm
In ADF mode, the intensity of light is below the standard level between sheets copyir.ocm Disconnect and then connect the connector of the scanner HP sensor copyir.ocm Replace the scanner HP sensor copyir.ocm Replace the scanner motor copyir.ocm Replace the reader controller PCB copyir.ocm
E227-0001 The reader unit power supply (24 V) has a fault copyir.ocm
At power-on, the 24V port is off copyir.ocm Disconnect and then connect the reader power supply connector copyir.ocm Replace the power supply copyir.ocm
E227-0002 The reader unit power supply (24 V) has a fault copyir.ocm
At the start of a job, the 24V port is off copyir.ocm Disconnect and then connect the reader power supply connector copyir.ocm Replace the power supply copyir.ocm
E227-0003 The reader unit power supply (24 V) has a fault copyir.ocm
At the end of a job, the 24V port is off copyir.ocm Disconnect and then connect the reader power supply connector copyir.ocm Replace the power supply copyir.ocm
E227-0004 The reader unit power supply (24 V) has a fault copyir.ocm
While a load is driven, the 24V port is off copyir.ocm Disconnect and then connect the reader power supply connector copyir.ocm Replace the power supply copyir.ocm
E240-0000 A fault exists in the communication between the main controller and the DC controller copyir.ocm
A fault has occurred in the communication between the CPUs of the main controller and the DC controller copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the DC controller PCB copyir.ocm Replace the main controller PCB copyir.ocm
E248-0000 A fault exists in the following: main controller SRAM, reader controller EEPROM copyir.ocm
At start-up, an SRAM check error has occurred copyir.ocm Replace the main controller PCB copyir.ocm
E248-0001 A fault exists in the following: main controller SRAM, reader controller EEPROM copyir.ocm
An error has occurred at time of power-on (EEPROM) copyir.ocm Replace the reader controller PCB copyir.ocm
E248-0002 A fault exists in the following: main controller SRAM, reader controller EEPROM copyir.ocm
An error has occurred during write operation (EEPROM) copyir.ocm Replace the reader controller PCB copyir.ocm
E248-0003 A fault exists in the following: main controller SRAM, reader controller EEPROM copyir.ocm
A read error has occurred after write operation (EEPROM) copyir.ocm Replace the reader controller PCB copyir.ocm
E251-0000 The inverter cooling fan rotation is faulty copyir.ocm Disconnect and then connect J1110 of the reader controller PCB copyir.ocm Replace the inverter cooling fan copyir.ocm Replace the reader controller PCB copyir.ocm
E302-0000 Shading operation is faulty copyir.ocm
In the course of shading operation, the processing doses not end within the reader controller copyir.ocm Disconnect and then connect J1107 and J1108 of the reader controller PCB copyir.ocm Replace the reader controller PCB copyir.ocm
E315-0007 The image data codec has a fault copyir.ocm
A JBIG encoder error has occurred copyir.ocm Replace the main controller PCB copyir.ocm
E315-000d The image data codec has a fault copyir.ocm
A JBIG decoding error has occurred copyir.ocm Replace the DDR-SDRAM copyir.ocm Replace the HDD copyir.ocm Replace the main controller PCB copyir.ocm
E315-000e The image data codec has a fault copyir.ocm
An error has occurred in the course of software decoding copyir.ocm Replace the DDR-SDRAM copyir.ocm Replace the HDD copyir.ocm Replace the main controller PCB copyir.ocm
E315-0100 The image data codec has a fault copyir.ocm
An overrun error has occurred copyir.ocm Replace the main controller PCB copyir.ocm
E315-0200 The image data codec has a fault copyir.ocm
The open I/F relay PCB has detected an error (no recovery after a retry) copyir.ocm Replace the open I/F relay PCB (relay PCB between the main controller and PS controller) copyir.ocm
E315-0300 The image data codec has a fault copyir.ocm
Cubic time-out Turn off and then back on he power copyir.ocm Replace the main controller PCB copyir.ocm
E315-0400 The image data codec has a fault copyir.ocm
Shift Device A time-out Turn off and then back on he power copyir.ocm Replace the main controller PCB copyir.ocm
E315-0401 The image data codec has a fault copyir.ocm
Shift Device B time-out Turn off and then back on he power copyir.ocm Replace the main controller PCB copyir.ocm
E351-0000 An error has occurred in the main controller communication copyir.ocm
At start-up, a main controller communication error has occurred copyir.ocm Replace the main controller PCB copyir.ocm
E400-0001 An ADF communication error has occurred copyir.ocm
A check sum error has occurred copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the reader controller PCB copyir.ocm Replace the ADF controller PCB copyir.ocm
E400-0002 An ADF communication error has occurred copyir.ocm
A reception status error has occurred copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the reader controller PCB copyir.ocm Replace the ADF controller PCB copyir.ocm
E400-0003 An ADF communication error has occurred copyir.ocm
A reception interrupt error has occurred copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the reader controller PCB copyir.ocm Replace the ADF controller PCB copyir.ocm
E402-0000 The ADF belt motor rotation is faulty copyir.ocm
While the belt motor drive signal is on, no lock signal occurs for 100 msec copyir.ocm Disconnect and then connect the cable between the belt motor driver PCB and the ADF controller PCB copyir.ocm Replace the belt motor clock sensor copyir.ocm Replace the belt motor clock sensor copyir.ocm Replace the belt motor copyir.ocm Replace the belt motor driver PCB copyir.ocm Replace the ADF controller PCB copyir.ocm
E404-0000 The ADF delivery motor rotation is faulty copyir.ocm
When the delivery motor drive signal is on, no clock signal occurs for 200 msec Replace the delivery motor copyir.ocm Replace the delivery motor clock sensor copyir.ocm Replace the ADF controller PCB copyir.ocm
E405-0000 The ADF separation motor rotation is faulty copyir.ocm
When the separation motor drive signal is on, no clock signal occurs for 200 msec copyir.ocm Replace the separation motor copyir.ocm Replace the separation motor clock sensor copyir.ocm Replace the ADF controller PCB copyir.ocm
E410-0000 The ADF pickup motor rotation is faulty copyir.ocm
No signal occurs from the following sensors within 2 sec after the pickup motor is driven: – pickup roller height sensor 1 (PI8), pickup roller height sensor 2 (PI9) – pickup roller HP sensor (PI7) Replace the pickup motor copyir.ocm Replace the pickup roller height sensor (PI8) copyir.ocm Replace the pickup roller height sensor 2 (PI9) copyir.ocm Replace the pickup roller HP sensor (PI7) copyir.ocm Replace the ADF controller PCB copyir.ocm
E413-0001 The ADF shift motor rotation is faulty copyir.ocm
The shift motor HP sensor is open copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the shift motor HP sensor copyir.ocm Replace the shift motor copyir.ocm
E413-0002 The ADF shift motor rotation is faulty copyir.ocm
Shift motor HP sensor is closed copyir.ocm Disconnect and then connect the connector copyir.ocm Replace the shift motor HP sensor copyir.ocm Replace the shift motor copyir.ocm
E420-0000 An ADF EEPROM read error has occurred copyir.ocm
At power-on, an attempt to read the EEPROM backup data fails copyir.ocm Or, data that has been read has a fault copyir.ocm Replace the ADF controller PCB copyir.ocm
E490-0001 The ADF is of the wrong type copyir.ocm Replace the ADF copyir.ocm
E602 The HDD has an error copyir.ocm
E604-0000 The time memory (DDR-SDRAM) is faulty or inadequate copyir.ocm
A DDR-SDRAM (1 GB) of adequate capacity is not detected copyir.ocm Replace the DDR-SDRAM copyir.ocm
E609-0008 The HDD temperature is abnormally low copyir.ocm
At start-up, the HDD does not reach a specific temperature within a specific time copyir.ocm Replace the HDD copyir.ocm
E609-0009 The HDD temperature is abnormally low copyir.ocm
When returning from sleep mode, the HDD does not reach a specific temperature within a specific time Replace the HDD copyir.ocm
E610 The HDD encryption key is faulty copyir.ocm
E711-0001 An error has occurred in the communication between the pickup/delivery accessory and the printer unit copyir.ocm
The communication controller has detected a fault copyir.ocm Turn off and then back on the power copyir.ocm (Turn off the machine and its delivery accessories; then, turn back on all accessories and then the machine copyir.ocm) Connect the communication cables and terminals between the machine and the delivery accessories once again copyir.ocm Replace the accessories controller PCB copyir.ocm Replace the transceiver PCB copyir.ocm
E712-0001 An error exists in the communication between the ADF and the reader unit copyir.ocm
As much as 5 sec or more has passed without recovery after communication stopped between the reader controller and the ADF controller copyir.ocm Disconnect and then connect the connectors between the reader unit and the ADF copyir.ocm Replace the reader controller PCB copyir.ocm Replace the ADF controller PCB copyir.ocm
E717-0001 An error exists in the communication with the NE controller copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The NE controller that has been connected before power-off is not recognized at power-on copyir.ocm Disconnect and then connect the main controller PCB copyir.ocm Install the NE controller copyir.ocm Replace the NE controller copyir.ocm
E717-0002 An error exists in the communication with the NE controller copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
An error that cannot be reset (e copyir.ocmg copyir.ocm, cable break) has been detected in the communication copyir.ocm Disconnect and then connect the main controller PCB copyir.ocm Install the NE controller copyir.ocm Replace the NE controller copyir.ocm
E719-0001 An error has occurred in the communication with the coin vendor/card reader copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The coin vendor that was connected before power-off is not recognized at power-on copyir.ocm Disconnect and then connect the connector of the main controller PCB copyir.ocm Install the coin vendor copyir.ocm Replace the coin vendor copyir.ocm
E719-0002 An error has occurred in the communication with the coin vendor/card reader copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the coin vendor, an error that cannot be reset has occurred (e copyir.ocmg copyir.ocm, cable break) Disconnect and then connect the connector of the main controller PCB copyir.ocm Install the coin vendor copyir.ocm Replace the coin vendor copyir.ocm
E719-0003 An error has occurred in the communication with the coin vendor/card reader copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the coin vendor, a communication error has occurred during acquisition of unit price information copyir.ocm Disconnect and then connect the connector of the main controller PCB copyir.ocm Install the coin vendor copyir.ocm Replace the coin vendor copyir.ocm
E719-0011 An error has occurred in the communication with the coin vendor/card reader copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
The card reader that was connected before power-off is not recognized at power-on copyir.ocm Disconnect and then connect the connector of the main controller PCB copyir.ocm Install the card reader copyir.ocm Replace the card reader copyir.ocm
E719-0012 An error has occurred in the communication with the coin vendor/card reader copyir.ocm After correcting the fault, be sure to reset the error copyir.ocm (COPIER>FUNCTION>CLEAR>ERR)
In the communication with the card reader, an error that cannot be reset has occurred (e copyir.ocmg copyir.ocm, cable break) copyir.ocm Disconnect and then connect the connector of the main controller PCB copyir.ocm Install the card reader copyir.ocm Replace the card reader copyir.ocm
E730-1001 A PDL-related error has occurred copyir.ocm
An initialization error has occurred at the start of a job copyir.ocm Reset the PDL mechanism copyir.ocm Turn off and then on the power copyir.ocm
E730-100A A PDL-related error has occurred copyir.ocm
An error has occurred in the communication with an external controller copyir.ocm Reset the PDL mechanism copyir.ocm Turn off and then on the power copyir.ocm
E730-9004 A PDL-related error has occurred copyir.ocm
A fault has been detected in the cable connection with an external controller copyir.ocm Turn off and then on the power copyir.ocm Replace the external controller relay PCB copyir.ocm Replace the external controller copyir.ocm
E730-9005 A PDL-related error has occurred copyir.ocm
A fault has been detected in the cable connection with an external controller copyir.ocm Turn off and then on the power copyir.ocm Replace the external controller relay PCB copyir.ocm Replace the external controller copyir.ocm
E730-A006 A PDL-related error has occurred copyir.ocm
The PDL mechanism does not respond copyir.ocm Reset the PDL mechanism copyir.ocm Turn off and then on the power copyir.ocm Reinstall the system software copyir.ocm Replace the main controller copyir.ocm
E730-A007 A PDL-related error has occurred copyir.ocm
At start-up, the version of the machine control software and that of the PDL control software do not match copyir.ocm Reset the PDL mechanism copyir.ocm Turn off and then on the power copyir.ocm Reinstall the system software copyir.ocm Replace the main controller copyir.ocm
E730-B013 A PDL-related error has occurred copyir.ocm
The font data is corrupted at start-up copyir.ocm Turn off and then on the power copyir.ocm Reinstall the system software copyir.ocm Execute full formatting of the HDD, and reinstall the system software copyir.ocm
E732-0001 An error has occurred in the communication between the reader unit and the main controller copyir.ocm
An error has occurred in the communication between the reader unit and the main controller copyir.ocm Disconnect and connect the connectors of the read communication cable copyir.ocm Check the power supply of the reader unit (to see if initialization occurs at power-on) copyir.ocm Replace the reader controller PCB copyir.ocm Reap the reader I/F PCB copyir.ocm Replace the main controller PCB copyir.ocm
E732-0010 An error has occurred in the communication between the reader unit and the main controller copyir.ocm
A fault has been detected in the reader sync signal detection mechanism copyir.ocm Disconnect and connect the connectors of the read communication cable copyir.ocm Check the power supply of the reader unit (to see if initialization occurs at power-on) copyir.ocm Replace the reader controller PCB copyir.ocm Reap the reader I/F PCB copyir.ocm Replace the main controller PCB copyir.ocm
E733-0000 An error has occurred in the communication between the reader unit and the main controller copyir.ocm
An error has occurred in the communication between the reader unit and the main controller copyir.ocm Disconnect and then connect the connector copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up) copyir.ocm Replace the DC controller PCB copyir.ocm Replace the main controller PCB copyir.ocm
E733-0001 An error has occurred in the communication between the reader unit and the main controller copyir.ocm
An attempt to communicate with the DC controller fails Disconnect and then connect the connector copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up) copyir.ocm Replace the DC controller PCB copyir.ocm Replace the main controller PCB copyir.ocm
E733-0010 An error has occurred in the communication between the reader unit and the main controller copyir.ocm
A fault has occurred in the printer engine sync signal detection mechanism copyir.ocm Disconnect and then connect the connector copyir.ocm Check the power supply of the DC controller (to see if initialization occurs at time of start-up) copyir.ocm Replace the DC controller PCB copyir.ocm Replace the main controller PCB copyir.ocm
E740-0002 An error exists in the LAN controller copyir.ocm
An illegal MAC address has been detected at start-up copyir.ocm Replace the main controller PCB copyir.ocm
E743-0000 A fault exists in the communication between the main controller and the reader controller copyir.ocm
The reader controller has detected an error in the communication between the main controller and the reader controller copyir.ocm Disconnect and then connect the connectors of the reader communications cable copyir.ocm Replace the reader controller PCB copyir.ocm Replace the main controller PCB copyir.ocm
E744-0001 An error exists in the language file/boot ROM copyir.ocm
The version of the language file on the HDD and that of bootable do not match copyir.ocm Update the version of the language file (Language), or install the appropriate file copyir.ocm
E744-0002 An error exists in the language file/boot ROM copyir.ocm
The language file on the HDD is too large copyir.ocm Update the version of the language file (Language), or install the appropriate file copyir.ocm
E744-0003 An error exists in the language file/boot ROM copyir.ocm
There is no language to which a switchover is made as described in the Config file on the HDD copyir.ocm Update the version of the language file (Language), or install the appropriate file copyir.ocm
E744-0004 An error exists in the language file/boot ROM copyir.ocm
An attempt to switch over to the language described in the Config file on the HDD fails copyir.ocm Update the version of the language file (Language), or install the appropriate file copyir.ocm
E744-1000 An error exists in the language file/boot ROM copyir.ocm
The connected boot ROM is not one designed for the model in question copyir.ocm Replace the boot ROM copyir.ocm
E744-2000 An error exists in the language file/boot ROM copyir.ocm
An illegal engine ID has been detected copyir.ocm Reinstall the system software copyir.ocm
E746-0003 An unsupported optional board has been detected copyir.ocm
The option board that has been detected is one deigned for a different model copyir.ocm Replace it with one for the model in question copyir.ocm
E749-0001 Restart in accordance with a change of the product configuration
A boot ROM designed for a different model has been fitted in place (as when installing an PDL option) copyir.ocm There is no need for remedial action copyir.ocm Nevertheless, the fact will remain as part of the error history copyir.ocm
E800 The auto power-off circuit has an error copyir.ocm
An open circuit has been detected for 3 sec or more in the auto power-off circuit copyir.ocm Turn off and then on the power copyir.ocm Disconnect and then connect J505 of the DC controller PCB copyir.ocm Disconnect and then connect J1719 of the relay PCB copyir.ocm Replace the relay PCB copyir.ocm Replace the DC controller PCB copyir.ocm
E804-0001 The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan copyir.ocm
The fan stop signal has been detected for 5 sec or more after the power supply cooling fan 1 has gone on copyir.ocm Disconnect and then connect J505 of the DC controller PCB copyir.ocm Replace the power supply cooling fan 1 copyir.ocm Replace the DC controller PCB copyir.ocm
E804-0002 The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan copyir.ocm
The fan stop signal has been detected for 5 sec or more after the power supply cooling fan 2 has gone on copyir.ocm Disconnect and then connect J505 of the DC controller PCB copyir.ocm Replace the power supply cooling fan 2 copyir.ocm Replace the DC controller PCB copyir.ocm
E804-0004 The rotation of the following is faulty: power supply cooling fan 1, power supply cooling fan 2, controller cooling fan copyir.ocm
The fan stop signal of the controller cooling fan has been detected continuously for 16 sec copyir.ocm Disconnect and then connect J1028 of the main controller PCB copyir.ocm Replace the controller cooling fan copyir.ocm Replace the main controller PCB copyir.ocm
E805-0002 The fixing heat discharge fan rotation is faulty copyir.ocm
The fan stop signal has been detected for 5 sec or more after the fixing heat discharge fan has gone on copyir.ocm Disconnect and then connect J503 of the DC controller PCB copyir.ocm Replace the fixing heat discharge fan copyir.ocm Replace the DC controller PCB copyir.ocm
E820-0000 The drum fan rotation is faulty copyir.ocm
The fan stop signal has been detected for 5 sec or more after the drum fan has gone on copyir.ocm Disconnect and then connect J512 of the DC controller PCB copyir.ocm Replace the drum fan copyir.ocm Replace the DC controller PCB copyir.ocm
E823-0000 The pre-transfer charging assembly fan rotation is faulty copyir.ocm
The fan stop signal has been detected for 5 sec or more after the pre-transfer charging assembly fan has gone on copyir.ocmulty copyir.ocm Disconnect and then connect J504 of the DC controller PCB copyir.ocm Replace the pre-transfer charging assembly fan copyir.ocm Replace the DC controller PCB copyir.ocm
E840-0000 An HP detection error has occurred in relation to the fixing inlet sensor (fixing wrap jam detection) copyir.ocm
The home position is not detected when he sensor is moved up/down (i copyir.ocme copyir.ocm, the sensor has not gone on) copyir.ocm Disconnect and then connect J508, J552, and J553 of the DC controller PCB copyir.ocm Disconnect and then connect J4001 and J4002 of the fixing inlet sensor ascent/descent motor driver PCB; as necessary, replace the fixing inlet sensor ascent/ descent motor copyir.ocm Replace the fixing inlet sensor ascent/descent motor driver PCB copyir.ocm
E840-0001 An HP detection error has occurred in relation to the fixing inlet sensor (fixing wrap jam detection) copyir.ocm
The home position is not detected when the sensor is moved up/down (i copyir.ocme copyir.ocm, the sensor has not gone off) copyir.ocm Disconnect and then connect J508, J552, and J553 of the DC controller PCB copyir.ocm Disconnect and then connect J4001 and J4002 of the fixing inlet sensor ascent/descent motor driver PCB; as necessary, replace the fixing inlet sensor ascent/ descent motor copyir.ocm Replace the fixing inlet sensor ascent/descent motor driver PCB copyir.ocm
E850- There is a fault in the double-feeding detection unit copyir.ocm
The double-feeding sensor (reception) fails to attain an ultrasonic signal of a specific level copyir.ocm Remove paper lint form the surface of the double-feeding sensor (reception) copyir.ocm Remount the double-feeding sensor (transmission, reception) copyir.ocm Disconnect and then connect J509 and J550 of the DC controller PCB copyir.ocm Replace the double-feeding sensor (transmission, reception) copyir.ocm Replace the double-feeding sensor PCB (transmission, reception) copyir.ocm
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.