توشیبا Toshiba 3910
1404-08-13
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
08 RX Motor Error
The machine checks the motor error signal in one second the motor starts driving copyir.com When the error signal is detected for continuous 300ms, this message will be displayed copyir.com 1 copyir.com Check the connection between RX motor and main control board copyir.com 2 copyir.com Verify the RX motor rotates when the power is on copyir.com If OK, see step 5 copyir.com 3 copyir.com Check that power is supplied to the Rx motor copyir.com If it does not, see step 5 copyir.com 4 copyir.com Replace the RX motor if it doesn’t rotate copyir.com 5 copyir.com If the problem is not solved, replace the main control board copyir.com
0B Fan Error
The machine checks the fan error signal for three seconds in one second after the motor starts driving copyir.com When the error signal is detected for continuous 400ms, this message will be displayed copyir.com 1 copyir.com Verify the inside fan rotates when the power is on copyir.com 2 copyir.com Check the connection between the fan and Connect A PCB(P87), Connect A PCB (P80C) and the main board copyir.com 3 copyir.com Replace the fan motor if it doesn’t rotate copyir.com 4 copyir.com Replace the Connect A PCB copyir.com 5 copyir.com Replace the main control board copyir.com
18 Fuser Error
(The number indicates the detailed error code) 0 The fuser did not become to the main motor driving temperature in 50 seconds after printing started copyir.com 1 The fuser did not become to the paper pick-up temperature in 50 seconds after printing started copyir.com 2 The fuser did not become to the main motor driving temperature in 30 seconds after warming up started copyir.com 3 The fuser did not become to the warm-up finishing temperature in 30 seconds after the motor started driving copyir.com 4 A temperature of 250°C or higher is detected in a mode other than sleep mode copyir.com 5 The fuser does not warm after fuser error is solved and the power is turned OFF/ON copyir.com 6 A low temperature of 10°C is detected in 10 seconds after printing started copyir.com 7 A temperature of 190°C is detected in ready mode after printing finished copyir.com 1 copyir.com Turn on the power again, and verify the fuser warms up copyir.com If it does not, see step 4 copyir.com 2 copyir.com Check the contact between Fusing thermistor and Connect A PCB(P89) copyir.com 3 copyir.com Check the contact between Connect A PCB (P80C) and the main board copyir.com 4 copyir.com Replace the Fuser copyir.com 5 copyir.com After replacing the Fuser, verify the fuser warms up when the power is on copyir.com 6 copyir.com Replace the main control PCB copyir.com
1E Drum Cartridge Fuse Error
The machine could not blow the fuse copyir.com 1 copyir.com Verify the drum cartridge is set correctly copyir.com 2 copyir.com Check the point of contacts between drum cartridge and Connect A PCB (P86)?D 3 copyir.com Check the contact between Connect A PCB (P80C) and the main board copyir.com 4 copyir.com Replace the drum cartridge copyir.com 5 copyir.com Replace the Connect A PCB copyir.com 6 copyir.com Replace the main control PCB copyir.com
1XXYY System error: XX and YY are function returned values
– This error occurs with firmware or hardware defect copyir.com Firmware defect will be recovered by updating it, but hardware defect needs its replacement copyir.com 1 copyir.com Update the ROM using the USB memory automatically copyir.com 2 copyir.com Replace the network board copyir.com 3 copyir.com Replace the main control board copyir.com
2XXYY Setting data initialize error: XX and YY are function returned values
– Occurs mainly when the data stored on the CF memory card is corrupted copyir.com You may recover it by updating the firmware, if that does not work, clear the data copyir.com 1 copyir.com Update the ROM using the USB memory automatically copyir.com 2 copyir.com Perform “All RAM Clear” copyir.com 3 copyir.com Replace the storage (HDD/CF card) copyir.com 4 copyir.com Replace the network board copyir.com
300 Eternal reboot is detected copyir.com
– The firmware detected an incorrect status, and machine rebooted to recover them automatically copyir.com When this status is detected twice, this error occurs copyir.com You may better the auto-recover process by updating the firmware copyir.com The detail will be printed on the service report with developer’s code copyir.com 1 copyir.com Update the ROM using the USB memory automatically copyir.com 2 copyir.com Replace the storage (HDD/CF card) copyir.com
400 System data clearing error
– This error occurs with firmware or hardware defect copyir.com This error occurs when the machine reboots from “User data clear” or “All RAM clear”, and an incorrect status is detected copyir.com 1 copyir.com Update the ROM using the USB memory automatically copyir.com 2 copyir.com Replace the storage (HDD/CF card) copyir.com 3 copyir.com Replace the network board copyir.com
47 Developer Cartridge Fuse Error
The machine could not blow the fuse copyir.com 1 copyir.com Verify the toner cartridge is set correctly copyir.com 2 copyir.com Check the point of contacts between toner cartridge and Connect A PCB (P86) copyir.com 3 copyir.com Check the contact between Connect A PCB (P80C) and the main board copyir.com 4 copyir.com Replace the toner cartridge copyir.com 5 copyir.com Replace the Connect A PCB copyir.com 6 copyir.com Replace the main control PCB copyir.com
5XX Version mismatching error
– This error occurs when an optional CF memory card is attached to the network board, and the firmware version on the CF memory card and network board do not match copyir.com 1 copyir.com Update the ROM using the USB memory automatically copyir.com 2 copyir.com Replace the storage (HDD/CF card) copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.