کو نیکا مینو لتا di1610

کو نیکا مینو لتا di1610

C0045    Fuser fan motor error
• The LOCK signal remains HIGH or LOW continuously for a predetermined period of time while the Cooling Fan Motor remains energized     copyir.com    1 Check the Motor connectors for connection and correct as necessary 2 Check the fan for possible overload and correct as necessary     copyir.com 3 M2 operation check PWB-P MPJ13P- 1 to 3 (pulse) G to H-5 to 6 4 M3 operation check PWB-P MPJ6P-1 to 3 (pulse) E-9 to 10     copyir.com 5 Replace PWB-P     copyir.com
C0210    H     copyir.com V     copyir.com abnormal
• The Drum Charge Monitor Voltage (HVC_MON) signal falls outside a predetermined range at any time after the lapse of a predetermined period of time after the Power Switch has been turned ON     copyir.com • The Image Transfer Voltage Monitor signal (T_MON_V) and Image Transfer Current Monitor signal (T_MON_I) fall outside a corresponding predetermined range     copyir.com    1 Replace Fusing Unit     copyir.com 2     copyir.com Replace PWB-P
C0500    Fuser warm up error
• The voltage of the Thermistor remains low for a predetermined period of time when a warm-up cycle is started     copyir.com • The temperature detected by the Thermistor remains lower than a reference value for a predetermined period of time for the period of time that begins 5 sec     copyir.com after, and ends 9 sec     copyir.com after, the start of the warm-up cycle (where the temperature detected by the Thermistor is 80 °C or less)     copyir.com • The temperature detected by the Thermistor does not increase for a 3-sec     copyir.com period or more for the period of time that begins after the lapse of a predetermined period of time after the Fusing Roller Heater Lamp has been turned ON and ends when the lamp is turned OFF     copyir.com • The Fusing Roller Heater Lamp remains ON for a 30sec     copyir.com period or more (except during the period through which the Main Motor remains energized)     copyir.com    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0510    Fuser temperature low
• The temperature detected by the Thermistor remains lower than the set temperature continuously for a predetermined period of time while the fusing temperature control is being provided     copyir.com (The set temperatures are as follows: 140 °C during a print mode at 600 dpi; 70 °C during the standby mode     copyir.com)    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0520    Fuser overheat
• The temperature detected by the Thermistor remains higher than 235 °C for a predetermined period of time while the fusing temperature control is being provided     copyir.com    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0650    Scanner home sensor error
• The Scanner Home Position Sensor is not detected within the predetermined period of time after the Scanner Motor has started turning     copyir.com    1 M4 operation check     copyir.com 2 Replace PWB-P     copyir.com
C1200    ASIC memory abnormal
• An error occurred while writing to or reading the SRAM on the Control Board (PWB-C)     copyir.com    1 Turn the copier off, then on again     copyir.com 2 Check the connection of the memory on the PWB-P, and then correct it if necessary     copyir.com 3 Replace PWB-P     copyir.com
C1300    Polygon mirror motor error
• The LOCK signal is not detected within a predetermined period of time that begins 1 sec     copyir.com after the Polygon Motor has been energized     copyir.com • No new LOCK signal is detected for a 1-sec     copyir.com period that begins 1     copyir.com5 sec     copyir.com after the first LOCK signal was detected     copyir.com • The LOCK signal is not detected for a continuous 0     copyir.com5sec     copyir.com period in a state in which the Polygon Motor runs stably     copyir.com • The LOCK signal remains ON for a continuous 5-sec     copyir.com period or more when the Polygon Motor remains deenergized     copyir.com    1 Check cables for connection and correct as necessary     copyir.com 2 Replace PH Unit     copyir.com 3 Replace PWB-P     copyir.com
C133B    Communication with option error
• Communication could not be established with the Controller Control Board within 5 seconds while printing     copyir.com    1 Replace PWB-P     copyir.com
C133C    Modem error
• A malfunction occurred in the Modem    1 Replace NCU     copyir.com
C133D    ROM checksum error
• A malfunction occurred in the ROM     copyir.com    1 Replace PWB-P     copyir.com
C13F0    Laser error
• The laser output exceeds the upper limit value     copyir.com • The laser output remains lower than the lower limit value     copyir.com    1 Check cables for connection and correct as necessary     copyir.com 2 Replace PH Unit     copyir.com 3 Replace PWB-P     copyir.com
C1468    EEPROM error
• An EEPROM not written with initial data was detected     copyir.com    1 Unplug, then plug in the power cord, and turn off the copier, then turn it on again     copyir.com 2 Check the connection of the EEPROM on the PWB-P, and then correct it if necessary     copyir.com 3 Replace PWB-P     copyir.com 4 Replace EEPROM     copyir.com
C14A3    IR lamp malfunction
• The luminosity level of the Exposure Lamp is not stabilized within the predetermined period of time     copyir.com    1 Check the connection of the connectors, and then correct them if necessary     copyir.com 2 Replace PWB-P     copyir.com 3 Replace the Scanner Assy     copyir.com
C0045    Fuser fan motor error
• The LOCK signal remains HIGH or LOW continuously for a predetermined period of time while the Cooling Fan Motor remains energized     copyir.com    1 Check the Motor connectors for connection and correct as necessary 2 Check the fan for possible overload and correct as necessary     copyir.com 3 M2 operation check PWB-P MPJ13P- 1 to 3 (pulse) G to H-5 to 6 4 M3 operation check PWB-P MPJ6P-1 to 3 (pulse) E-9 to 10     copyir.com 5 Replace PWB-P     copyir.com
C0210    H     copyir.com V     copyir.com abnormal
• The Drum Charge Monitor Voltage (HVC_MON) signal falls outside a predetermined range at any time after the lapse of a predetermined period of time after the Power Switch has been turned ON     copyir.com • The Image Transfer Voltage Monitor signal (T_MON_V) and Image Transfer Current Monitor signal (T_MON_I) fall outside a corresponding predetermined range     copyir.com    1 Replace Fusing Unit     copyir.com 2     copyir.com Replace PWB-P
C0500    Fuser warm up error
• The voltage of the Thermistor remains low for a predetermined period of time when a warm-up cycle is started     copyir.com • The temperature detected by the Thermistor remains lower than a reference value for a predetermined period of time for the period of time that begins 5 sec     copyir.com after, and ends 9 sec     copyir.com after, the start of the warm-up cycle (where the temperature detected by the Thermistor is 80 °C or less)     copyir.com • The temperature detected by the Thermistor does not increase for a 3-sec     copyir.com period or more for the period of time that begins after the lapse of a predetermined period of time after the Fusing Roller Heater Lamp has been turned ON and ends when the lamp is turned OFF     copyir.com • The Fusing Roller Heater Lamp remains ON for a 30sec     copyir.com period or more (except during the period through which the Main Motor remains energized)     copyir.com    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0510    Fuser temperature low
• The temperature detected by the Thermistor remains lower than the set temperature continuously for a predetermined period of time while the fusing temperature control is being provided     copyir.com (The set temperatures are as follows: 140 °C during a print mode at 600 dpi; 70 °C during the standby mode     copyir.com)    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0520    Fuser overheat
• The temperature detected by the Thermistor remains higher than 235 °C for a predetermined period of time while the fusing temperature control is being provided     copyir.com    1 Replace Thermistor (TH1)     copyir.com 2 Replace Fusing Unit     copyir.com 3 Replace Controller/Mechanical Control Board (PWB-P)     copyir.com 4 Replace Power Unit (PU1)     copyir.com
C0650    Scanner home sensor error
• The Scanner Home Position Sensor is not detected within the predetermined period of time after the Scanner Motor has started turning     copyir.com    1 M4 operation check     copyir.com 2 Replace PWB-P     copyir.com
C1200    ASIC memory abnormal
• An error occurred while writing to or reading the SRAM on the Control Board (PWB-C)     copyir.com    1 Turn the copier off, then on again     copyir.com 2 Check the connection of the memory on the PWB-P, and then correct it if necessary     copyir.com 3 Replace PWB-P     copyir.com
C1300    Polygon mirror motor error
• The LOCK signal is not detected within a predetermined period of time that begins 1 sec     copyir.com after the Polygon Motor has been energized     copyir.com • No new LOCK signal is detected for a 1-sec     copyir.com period that begins 1     copyir.com5 sec     copyir.com after the first LOCK signal was detected     copyir.com • The LOCK signal is not detected for a continuous 0     copyir.com5sec     copyir.com period in a state in which the Polygon Motor runs stably     copyir.com • The LOCK signal remains ON for a continuous 5-sec     copyir.com period or more when the Polygon Motor remains deenergized     copyir.com    1 Check cables for connection and correct as necessary     copyir.com 2 Replace PH Unit     copyir.com 3 Replace PWB-P     copyir.com
C133B    Communication with option error
• Communication could not be established with the Controller Control Board within 5 seconds while printing     copyir.com    1 Replace PWB-P     copyir.com
C133C    Modem error
• A malfunction occurred in the Modem    1 Replace NCU     copyir.com
C133D    ROM checksum error
• A malfunction occurred in the ROM     copyir.com    1 Replace PWB-P     copyir.com
C13F0    Laser error
• The laser output exceeds the upper limit value     copyir.com • The laser output remains lower than the lower limit value     copyir.com    1 Check cables for connection and correct as necessary     copyir.com 2 Replace PH Unit     copyir.com 3 Replace PWB-P     copyir.com
C1468    EEPROM error
• An EEPROM not written with initial data was detected     copyir.com    1 Unplug, then plug in the power cord, and turn off the copier, then turn it on again     copyir.com 2 Check the connection of the EEPROM on the PWB-P, and then correct it if necessary     copyir.com 3 Replace PWB-P     copyir.com 4 Replace EEPROM     copyir.com
C14A3    IR lamp malfunction
• The luminosity level of the Exposure Lamp is not stabilized within the predetermined period of time     copyir.com    1 Check the connection of the connectors, and then correct them if necessary     copyir.com 2 Replace PWB-P     copyir.com 3 Replace the Scanner Assy     copyir.com