کو نیکا مینو لتا di2011

کو نیکا مینو لتا di2011

C0B60    Bin Switching Motor malfunction (Only when the optional JS-204 is mounted)
C0B80    Shift Motor malfunction (Only when the optional OT-103 is mounted)
C0F32    Faulty ATDC Sensor
• The measurement taken by the ATDC Sensor (UN1) at a time 2    copyir.com0 sec    copyir.com after the Main Motor (M1) has started a time 2    copyir.com0 sec    copyir.com after the Main Motor (M1) has started turning is less than 5% (greater than 4    copyir.com63 V)    copyir.com • The measurement taken by the ATDC Sensor (UN1) at a time 2    copyir.com0 sec    copyir.com after the Main Motor (M1) has started turning is 19% or more (1    copyir.com41 V or less)    copyir.com    1 Check to see if developer is available    copyir.com 2 Check the ATDC Sensor connectors for proper connection and correct as necessary    copyir.com 3 Change UN1    copyir.com 4 Run ?gATDC Auto Adjust 5 Change PWB-A 6 Change PU1    copyir.com
C0F33    Improperly adjusted ATDC Sensor
• The adjustment of the ATDC control voltage is not completed within 1 sec    copyir.com after sampling has started of the ATDC Sensor (UN1) as part of an operation of ATDC Sensor Automatic Adjustment    copyir.com • The ATDC Sensor control voltage falls outside the range of 5    copyir.com39 V to 8    copyir.com15 V during an operation of ATDC Sensor Automatic Adjustment    copyir.com    1 Check to see if developer is available    copyir.com 2 Check the ATDC Sensor connectors for proper connection and correct as necessary    copyir.com 3 Change UN1    copyir.com 4 Run ?gATDC Auto Adjust 5 Change PWB-A 6 Change PU1    copyir.com
C1038    Engine connection failure
Master Board (PWB-A) to Control Board (PWB-C/C) connection failure • There is no acknowledge signal transmitted from the Master Board (PWB-A) to Control Board (PWB-C/C) for 1    copyir.com5 sec    copyir.com or more    copyir.com • An error command signal is transmitted from the Control Board (PWB-C/C) to Master Board (PWB-A)    copyir.com • An error status signal is transmitted from the Master Board (PWB-A) to Control Board (PWB-C/C)    copyir.com    1 Turn OFF and ON the Power Switch    copyir.com 2 Check the PWB-A connectors for proper connection and correct as necessary    copyir.com 3 Check the PWB-C/C connectors for proper connection and correct as necessary    copyir.com 4 Check for proper connection between PWB-A and PWB-C/C and correct as necessary    copyir.com 5 Change PWB-A    copyir.com 6 Change PWB-C/C    copyir.com
C1200    Faulty ASIC/memory
ASIC/memory (for image and control) fault • A write or read error occurs with SRAM on the Control Board (PWB-C/C)    copyir.com Startup failure • A LOW Polygon Motor (M2) Lock signal is not detected within a given period of time that begins 1 sec    copyir.com after the Polygon Motor has started turning    copyir.com    1 Turn OFF and ON the Power Switch    copyir.com 2 Check memory on PWB-C/C for connection and correct as necessary    copyir.com 3 Change PWB-C/C    copyir.com
C1300    Polygon Motor malfunction
Lock signal fault: Unstable after the first Lock signal has been detected • For a period of 1 sec    copyir.com after the first LOW Polygon Motor (M2) Lock signal (first Lock) has been detected, the next LOW Polygon Motor Lock signal is not detected    copyir.com Lock signal fault: Lock signal out-of-timing • A LOW Polygon Motor (M2) Lock signal is not detected for a continuous given period of time while the rotation of the Polygon Motor remains stabilized    copyir.com Faulty Lock signal • A LOW Polygon Motor (M2) Lock signal is detected for a given period of time or more when the Polygon Motor remains deenergized    copyir.com    1 Turn OFF and ON the Power Switch    copyir.com 2 Check for proper connection between the PH Unit and Master Board and correct as necessary    copyir.com 3 Change the PH Unit    copyir.com 4 Change PWB-A    copyir.com
C133B    Communication with option error
• It is not possible to communicate with the Printer Board within a predetermined period of time during a print cycle    copyir.com
C133D    ROM check error
• An error is detected of the flash ROM chip on the Fax Board when the Power Switch is turned ON    copyir.com
C13F0    Faulty HSYNC
Laser scanning system malfunction • The SOS Sensor does not detect a rising edge of SOS within a given period of time after the Polygon Motor (M2) has started turning and a laser output has been started    copyir.com • The SOS Sensor detects no rising edges of SOS while VIA (image area control) is ON    copyir.com
C1468    Faulty EEPROM
EEPROM fault • Data cannot be written in EEPROM    copyir.com • Data stored in EEPROM is wrong    copyir.com    1 Turn OFF the Power Switch and unplug the power cord    copyir.com Then, plug in the power cord and turn ON the Power Switch again    copyir.com 2 Check EEPROM (U16) on PWB-C/C for proper connection and correct as necessary    copyir.com 3 Change PWB-A    copyir.com 4 Change EEPROM    copyir.com
C14A3    IR fluorescent lamp fault
The Exposure Lamp (LA2) of the Scanner fails to turn ON    copyir.com • The intensity of the Exposure Lamp is a predetermined value or less during shading and re-shading    copyir.com    1 Check that the Exposure Lamp (LA2) turns ON when the Power Switch is turned ON and correct or replace as necessary    copyir.com 2 Check connectors on PU2 for proper connection and correct as necessary    copyir.com 3 Check connectors on PWB-J for proper connection and correct as necessary    copyir.com 4 Change PWB-C/C    copyir.com