کیو سرا میتا taskalfa 300i

کیو سرا میتا taskalfa 300i

C0030    Fax control PWB system problem
Processing with the fax software was disabled due to a hardware or software problem        copyir.com    Defective fax control PWB        copyir.com
C0060    Main PWB type mismatch error    Defective PWB        copyir.com
C0070    Abnormal detection of fax control PWB incompatibility
In the initial communication with the fax control PWB, any normal communication command is not transmitted        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0100    Backup memory (EEPROM) device problem (Main PWB)
Reading from or writing to EEPROM cannot be performed        copyir.com    Defective main PWB        copyir.com
Device damage of EEPROM        copyir.com
C0120    MAC address data error
For data in which the MAC address is invalid        copyir.com    Defective main PWB        copyir.com
C0150    Backup memory (EEPROM) device problem (Engine PWB)
Reading from or writing to EEPROM cannot be performed        copyir.com    Defective engine PWB        copyir.com
Device damage of EEPROM        copyir.com
C0160    Backup memory (EEPROM) data problem (Engine PWB)
Reading data from EEPROM is abnormal        copyir.com Read and write data does not match 5 times continuously        copyir.com    Data damage of EEPROM        copyir.com
C0170    Copy counts problem
A checksum error is detected in the main and engine backup memories for the copy counters        copyir.com    Data damage of EEPROM        copyir.com
Defective PWB        copyir.com
C0180    Machine number mismatch error
Machine number of main PWB and engine PWB does not match        copyir.com    Data damage of EEPROM        copyir.com
C0320    Power CPU communication problem
The engine PWB and the power CPU are unable to communicate with each other        copyir.com    Defective engine PWB        copyir.com
C0420    Optional paper feeder communication problem
The engine PWB and the paper feeder are unable to communicate with each other        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C0620    FAX image DIMM problem
DIMM is not installed correctly        copyir.com DIMM cannot be accessed        copyir.com    DIMM installed incorrectly        copyir.com
Defective main PWB        copyir.com
C0630    DMA problem
DMA transmission of image data does not complete within the specified period of time        copyir.com    Poor contact in the connector terminals        copyir.com
Defective main PWB        copyir.com
C0640    Hard disk drive problem
The hard disk cannot be accessed        copyir.com    Poor contact in the connector terminals        copyir.com
Defective hard disk        copyir.com
Defective main PWB        copyir.com
C0650    FAX image DIMM check problem
Improper DIMM is installed        copyir.com    DIMM installed incorrectly        copyir.com
DIMM of another machine is installed        copyir.com
Defective main PWB        copyir.com
C0800    Image processing problem
JAM05 is detected twice        copyir.com    Defective main PWB        copyir.com
C0830    Fax control PWB flash program area checksum error
A checksum error occurred with the program of the fax control PWB        copyir.com    Defective fax software        copyir.com
Defective fax control PWB        copyir.com
C0840    Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed        copyir.com    Defective main PWB        copyir.com
The battery is disconnected from the main PWB        copyir.com
C0870    Fax control PWB to main PWB high capacity data transfer problem
High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed even if the data transfer was retried 10 times        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C0920    Fax file system error
The backup data is not retained for file system abnormality of flash memory of the fax control PWB        copyir.com    Defective fax control PWB        copyir.com
C1010    Lift motor 1 error
After cassette 1 is inserted, lift switch 1 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of lift motor 1        copyir.com
Defective lift motor 1        copyir.com
Poor contact in the connector terminals        copyir.com
Defective lift switch 1        copyir.com
Defective engine PWB        copyir.com
C1020    Lift motor 2 error
After cassette 2 is inserted, lift switch 2 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of lift motor 2        copyir.com
Defective lift motor 2        copyir.com
Poor contact in the connector terminals        copyir.com
Defective lift switch 2        copyir.com
Defective engine PWB        copyir.com
C1030    PF lift motor 1 error (optional paper feeder)
After cassette 3 is inserted, PF lift switch 1 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals        copyir.com
Broken gears or couplings of PF lift motor 1        copyir.com
Defective PF lift motor 1        copyir.com
Defective PF lift switch 1        copyir.com
C1040    PF lift motor 2 error (optional paper feeder)
After cassette 4 is inserted, PF lift switch 2 does not turn on within 12 s        copyir.com This error is detected four times successively        copyir.com    Poor contact in the connector terminals
Broken gears or couplings of PF lift motor 2        copyir.com
Defective PF lift motor 2        copyir.com
Defective PF lift switch 2        copyir.com
C2000    Main motor problem
Stable OFF is detected for 1 s continuously after main motor stability        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective main motor        copyir.com
Defective engine PWB        copyir.com
C2200    Drum motor problem
Stable OFF is detected for 1 s continuously after drum motor stability        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective drum motor        copyir.com
Defective engine PWB        copyir.com
C2500    Paper feed motor error
Stable OFF is detected for 1 s continuously after paper feed motor stability        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system        copyir.com
Defective paper feed motor        copyir.com
Defective engine PWB        copyir.com
C2600    PF paper drive motor error (optional paper feeder)
The lock signal of the motor is detected above 500 ms        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drive transmission system
Defective PF paper drive motor        copyir.com
Defective PWB
C3100    Scanner carriage problem
The home position is not correct when the power is turned on or at the start of copying using the table        copyir.com    Poor contact in the connector terminals        copyir.com
Defective home position switch        copyir.com
Defective scanner motor        copyir.com
The mirror frame, exposure lamp, or scanner wire is defective        copyir.com
Defective PWB        copyir.com
C3200    Exposure lamp problem
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s        copyir.com    Poor contact in the connector terminals        copyir.com
Defective exposure lamp        copyir.com
Incorrect shading position        copyir.com
Defective PWB        copyir.com
C3300    Optical system (AGC) problem
After AGC, correct input is not obtained at CCD        copyir.com    Poor contact in the connector terminals        copyir.com
Defective exposure lamp        copyir.com
Defective PWB        copyir.com
C3500    Communication error between scanner and SHD An error code is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C3900    Backup memory read/write problem (scanner PWB)
Read and write data does not match        copyir.com    Defective backup RAM or PWB        copyir.com
C3910    Backup memory data problem (scanner PWB)
Data in the specified area of the backup memory does not match the specified values        copyir.com    Defective backup RAM or PWB        copyir.com
C4000    Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on        copyir.com    Poor contact in the connector terminals        copyir.com
Defective polygon motor        copyir.com
Defective engine PWB        copyir.com
C4010    Polygon motor steady-state problem
Stable OFF is detected for 5 s continuously after polygon motor stability        copyir.com    Poor contact in the connector terminals        copyir.com
Defective polygon motor        copyir.com
Defective engine PWB        copyir.com
C4200    BD initialization problem
ASIC detects a BD error A for 4 s after the polygon motor rotation has been stabilized        copyir.com    Poor contact in the connector terminals        copyir.com
Defective polygon motor        copyir.com
Defective engine PWB        copyir.com
C6000    Fuser heater break
Fuser thermistor 1 detected less than 40°C/104°F for 14 s during warm-up and ready in        copyir.com Fuser thermistor 2 detected less than 70°C/158°F for 14 s during warm-up and ready in        copyir.com    Defective fuser heater 1 or 2        copyir.com
Installation defectiveness on fuser thermistor 1 or 2        copyir.com
Defective fuser thermostat        copyir.com
Defective PWB        copyir.com
C6020    Abnormally high fuser thermistor center temperature
Fuser thermistor 2 is detected 230°C/ 446°F or more for 40 ms        copyir.com    Installation defectiveness on fuser thermistor 2        copyir.com
Defective fuser thermistor 2        copyir.com
Defective engine PWB        copyir.com
C6050    Abnormally low fuser thermistor center temperature
Fuser thermistor 1 is detected 100°C/ 212°F less then 1 s continuously during copying        copyir.com    Defective fuser heater 1 or 2        copyir.com
Installation defectiveness on fuser thermistor 2        copyir.com
Defective PWB        copyir.com
C6120    Abnormally high fuser thermistor edge temperature
Fuser thermistor 1 is detected 240°C/ 464°F or more for 40 ms        copyir.com    Installation defectiveness on fuser thermistor 1        copyir.com
Defective fuser thermistor 1        copyir.com
Defective engine PWB        copyir.com
C6150    Abnormally low fuser thermistor edge temperature
Fuser thermistor 1 is detected 80°C/ 176°F less than 1 s continuously during copying        copyir.com    Defective fuser heater 1 or 2        copyir.com
Installation defectiveness on fuser thermistor 1        copyir.com
Defective PWB        copyir.com
C6400    Zero-cross signal error
While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s        copyir.com    Defective PWB
C6420    Fuser unit fuse cut problem
The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on        copyir.com    Poor contact in the connector terminals        copyir.com
Fuser unit connector inserted incorrectly        copyir.com
C7000    Toner motor problem
A motor over-current signal is detected continuously for 1 s or longer    Poor contact in the connector terminals        copyir.com
Broken the gear        copyir.com
Defective toner feed motor        copyir.com
Defective engine PWB        copyir.com
C7200    Broken inner thermistor wire
An abnormal value is detected in the input data to inner thermistor        copyir.com    Poor contact in the connector terminals        copyir.com
Defective temperature sensor        copyir.com
C7300    Toner hopper problem
Toner emptiness is detected for 300 s, three times during the toner replenishment        copyir.com    Poor contact in the connector terminals        copyir.com
Defective toner sensor        copyir.com
C7400    Developing unit connector insertion problem
Absence of the developing unit is detected        copyir.com    Developing unit connector inserted incorrectly        copyir.com
Defective developing unit connector        copyir.com
C7410    Drum unit connector insertion problem Absence of the drum unit is detected        copyir.com    Drum unit connector inserted incorrectly        copyir.com
Defective drum unit connector        copyir.com
C7800    Broken external thermistor wire
The thermistor output value is 4        copyir.com5 V or more        copyir.com    Poor contact in the connector terminals        copyir.com
Defective humidity sensor
C7900    Drum EEPROM error
Reading from or writing to EEPROM cannot be performed        copyir.com    Poor contact in the connector terminals        copyir.com
Defective drum unit        copyir.com
C7910    Developing unit EEPROM error
Reading from or writing to EEPROM cannot be performed        copyir.com    Poor contact in the connector terminals
Defective developing unit        copyir.com
C8030    Tray upper limit detection problem (optional document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected        copyir.com    The tray upper limit sensor, paper surface sensor 1/2 connector makes poor contact        copyir.com
Defective tray upper limit sensor, paper surface sensor 1/2        copyir.com
Defective finisher main PWB        copyir.com
C8040    Belt problem (optional document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on        copyir.com    The belt sensor, belt solenoid connector makes poor contact        copyir.com
Defective belt sensor        copyir.com
Defective belt solenoid        copyir.com
Defective finisher main PWB        copyir.com
C8140    Tray elevation motor problem (optional document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated        copyir.com    The tray elevation motor connector makes poor contact        copyir.com
The tray elevation motor malfunctions        copyir.com
The tray lower limit sensor, paper surface sensor 1/2 connector makes poor contact        copyir.com
Defective tray lower limit sensor, paper surface sensor 1/2        copyir.com
Defective finisher main PWB        copyir.com
C8170    Finisher front side registration motor problem (optional built-in finisher)
When the front-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses        copyir.com When the front-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s        copyir.com    The front side registration motor connector makes poor contact        copyir.com
Defective front side registration motor        copyir.com
The front side registration home position sensor connector makes poor contact        copyir.com
Defective front side registration home position sensor        copyir.com
Defective finisher control PWB        copyir.com
C8180    Finisher rear side registration motor problem (optional built-in finisher)
When the rear-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses        copyir.com When the rear-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s        copyir.com    The rear side registration motor connector makes poor contact        copyir.com
Defective rear side registration motor        copyir.com
The rear side registration home position sensor connector makes poor contact        copyir.com
Defective rear side registration home position sensor        copyir.com
Defective finisher control PWB        copyir.com
C8190    Finisher trailing edge registration motor problem (optional built-in finisher)
When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses        copyir.com When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s        copyir.com    The trailing edge registration motor connector makes poor contact        copyir.com
Defective trailing edge registration motor
The trailing edge registration home position sensor connector makes poor contact        copyir.com
Defective trailing edge registration home position sensor        copyir.com
Defective finisher control PWB        copyir.com
C8210    Stapler problem (optional document finisher)
Jam 82 is indicated        copyir.com
Finisher stapler problem (optional built-in finisher)
The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation        copyir.com During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation        copyir.com    The stapler connector makes poor contact        copyir.com
The stapler is blocked with a staple        copyir.com
The stapler is broken        copyir.com
Defective finisher main PWB        copyir.com
The stapler connector makes poor contact        copyir.com
The stapler is blocked with a staple        copyir.com
The stapler is broken        copyir.com
Defective finisher control PWB        copyir.com
C8320    Adjustment motor 2 problem (optional document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on        copyir.com    The adjustment sensor 2, adjustment motor 2 connector makes poor contact        copyir.com
Defective adjustment sensor 2        copyir.com
Defective adjustment motor 2        copyir.com
Defective finisher main PWB        copyir.com
C8330    Adjustment motor 1 problem (optional document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on        copyir.com    The adjustment sensor 1, adjustment motor 1 connector makes poor contact        copyir.com
Defective adjustment sensor 1
Defective adjustment motor 1        copyir.com
Defective finisher main PWB        copyir.com
C8350    Roller motor problem (optional document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on        copyir.com    The roller sensor, roller motor connector makes poor contact        copyir.com
Defective roller sensor        copyir.com
Defective roller motor        copyir.com
Defective finisher main PWB        copyir.com
C8360    Slide motor problem (optional document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on        copyir.com    The slide sensor, slide motor connector makes poor contact        copyir.com
Defective slide sensor        copyir.com
Defective slide motor
Defective finisher main PWB
C8440    Sensor adjusting problem (optional document finisher)
The sensor cannot be adjusted within the specified range        copyir.com    The paper entry sensor connector makes poor contact        copyir.com
Defective paper entry sensor        copyir.com
The optical path of the paper entry sensor is blocked by foreign matter        copyir.com
Defective finisher main PWB        copyir.com
C8460    EEPROM problem (optional document finisher)
Reading from or writing to EEPROM cannot be performed        copyir.com    Defective EEPROM or finisher main PWB        copyir.com
C8800    Document finisher communication error (optional 3000-sheet document finisher)
A communication error from document finisher is detected 10 times in succession    Poor contact in the connector terminals        copyir.com
Defective PWB        copyir.com
C9000    Optional DP communication problem
A communication error is detected        copyir.com    Poor contact in the connector terminals        copyir.com
Defective DP main PWB        copyir.com
C9060    DP EEPROM error (optional DP)
Read and write data does not match        copyir.com Data in the specified area of the backup memory does not match the specified values        copyir.com Data in the specified area of the backup memory does not match the specified values        copyir.com    Defective DP main PWB        copyir.com
Device damage of EEPROM        copyir.com
C9500, C9510, C9520    Contact the Service Administrative Division        copyir.com
F000    Operation panel PWB communication error    Defective main PWB        copyir.com
Defective operation panel PWB        copyir.com
F040    Engine PWB communication error    Defective main PWB        copyir.com
Defective engine PWB        copyir.com
F041    Scanner PWB communication error    Defective main PWB        copyir.com
Defective scanner PWB        copyir.com
F050    Engine ROM checksum error    Defective engine PWB        copyir.com
F090    Fax control PWB communication error    Defective main PWB
F278    Power supply in drive system error    Main power switch was turned off without using the power key, or a power failure has occurred        copyir.com