توشیبا Toshiba 3910
1404-08-13
نماد اعتماد از وزارت صنعت و معدن
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.
C1 Close Separation fan unit
• If the actuator of the Separation base unit safety switch is not depressed copyir copyir copyir.comcomcom
C2 Close Master Making Unit
• If the actuator of the Master making unit safety switch is not depressed copyir copyir copyir.comcomcom
C3 Close Master Removal Unit
• If the actuator of the Master removal unit safety switch is not depressed copyir copyir copyir.comcomcom
C4 Set master disposal box copyir copyir copyir.comcomcom
• If the master disposal box set sensor does not detect copyir copyir copyir.comcomcom
C5 Set Ink bottle in Place
• If the Ink bottle set sensor does not detect the Ink bottle copyir copyir copyir.comcomcom
C6 Replace Master Roll
• If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation copyir copyir copyir.comcomcom
C7 Empty Disposal Box
• If the Master removal 5 times copyir copyir copyir.comcomcom
C8 Replace Ink bottle
• If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated copyir copyir copyir.comcomcom
• If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle copyir copyir copyir.comcomcom
E1 Main Motor Lock
• If excessive current is detected 0 copyir copyir copyir.comcomcom3 seconds consecutively after the Main motor is activated copyir copyir copyir.comcomcom
• If no Encoder sensor output after Main motor is activated copyir copyir copyir.comcomcom
E12 Master removal motor lock
• Excessive current to the motor is detected three time consecutively during the current check made every 100 ms copyir copyir copyir.comcomcom
E13 Cutter motor Lock
• If the Cutter home position switch is not turned OFF within 500 ms after the Cutter motor is activated copyir copyir copyir.comcomcom
• If the Cutter end position switch is not pressed within 2000 ms after the Cutter motor is activated copyir copyir copyir.comcomcom
E16 Inking Motor Lock
• If excessive current is detected 2 copyir copyir copyir.comcomcom5 seconds consecutively after the Inking motor is activated copyir copyir copyir.comcomcom
E19 TPH pressure error [During TPH Up Positioning]
• If the light path of the TPH pressure sensor is not opened within 10 seconds after the Write pulse motor is activated copyir copyir copyir.comcomcom [During TPH Down Positioning]
• If the light path of the TPH pressure sensor is not blocked within 10 seconds after the Write pulse motor is activated copyir copyir copyir.comcomcom
E3 Clamp Motor Lock [During Clamp Motor Initial Positioning]
• If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated copyir copyir copyir.comcomcom [During Master Release from the Clamp Plate]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated copyir copyir copyir.comcomcom
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated copyir copyir copyir.comcomcom [When the Clamp Plate opens during Master Clamping]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated copyir copyir copyir.comcomcom
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated copyir copyir copyir.comcomcom [When the Clamp Plate closes during Master Clamping]
• If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated copyir copyir copyir.comcomcom
E4 Ink Overflow
• If the Overflow sensor detects excessive ink in the Squeegee unit copyir copyir copyir.comcomcom
E6 Position copyir copyir copyir.comcomcomA Sensor Malfunction
• If Position copyir copyir copyir.comcomcomA sensor cannot be detected (or keeps detecting copyir copyir copyir.comcomcom even though the Main motor encoder sensor signal is making the output after the Main motor is activated copyir copyir copyir.comcomcom
J1 No Master on the Drum
• If the Master sensor does not find master on the Drum when the Drum is at 134° during the printing movement copyir copyir copyir.comcomcom
J10 Removed Master Jammed at the Master removal area
• If the Master removal sensor is detecting the removed master (light path blocked copyir copyir copyir.comcomcom even though the Drum has returned to the position copyir copyir copyir.comcomcomA after the master removal process copyir copyir copyir.comcomcom
J2 Paper Jam in the Second Paper Feed Area
• If the Paper receiving sensor does not find paper when the Drum is at Position copyir copyir copyir.comcomcom334° and 104° the printing operation copyir copyir copyir.comcomcom
J3 Paper Jam in the Paper Receiving Area
• If the status of the Paper receiving sensor does not change from detecting paper to not detecting from Drum angle 357° to 280° the printing operation copyir copyir copyir.comcomcom
J4 Master Loading Error
• If the Master sensor does not detect the master (light not reflected copyir copyir copyir.comcomcom within 5 seconds copyir copyir copyir.comcomcom
J5 Master Loading Error (onto the Drum copyir copyir copyir.comcomcom
• If the Master sensor does not detect the master (light not reflected copyir copyir copyir.comcomcom during the master loading when the Drum is at 134° from the position copyir copyir copyir.comcomcomA copyir copyir copyir.comcomcom
J6 Master Cut Malfunction
• If the Master positioning sensor is still detecting the master (light reflected back copyir copyir copyir.comcomcom when the Drum is at position copyir copyir copyir.comcomcomA after the cutting copyir copyir copyir.comcomcom
J7 Original Jam at Entrance
• During the Original scanning, if the Original IN sensor does not detecting within 5 second after the Read pulse motor activates copyir copyir copyir.comcomcom
J8 Original Jam
• During the Original set movement, if the Original IN sensor still detecting Original (sensor light reflected copyir copyir copyir.comcomcom the master making movement copyir copyir copyir.comcomcom
J9 Master Removal Error
• In case the Master removal sensor does not detect the removed master (light path opened copyir copyir copyir.comcomcom at Drum 134° from the Position copyir copyir copyir.comcomcomA during the master removal even though a master was detected on the Drum before the master removal operation copyir copyir copyir.comcomcom
C1 Close Separation fan unit
• If the actuator of the Separation base unit safety switch is not depressed copyir.com
C2 Close Master Making Unit
• If the actuator of the Master making unit safety switch is not depressed copyir.com
C3 Close Master Removal Unit
• If the actuator of the Master removal unit safety switch is not depressed copyir.com
C4 Set master disposal box copyir.com
• If the master disposal box set sensor does not detect copyir.com
C5 Set Ink bottle in Place
• If the Ink bottle set sensor does not detect the Ink bottle copyir.com
C6 Replace Master Roll
• If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation copyir.com
C7 Empty Disposal Box
• If the Master removal 5 times copyir.com
C8 Replace Ink bottle
• If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated copyir.com
• If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle copyir.com
E1 Main Motor Lock
• If excessive current is detected 0 copyir.com3 seconds consecutively after the Main motor is activated copyir.com
• If no Encoder sensor output after Main motor is activated copyir.com
E12 Master removal motor lock
• Excessive current to the motor is detected three time consecutively during the current check made every 100 ms copyir.com
E13 Cutter motor Lock
• If the Cutter home position switch is not turned OFF within 500 ms after the Cutter motor is activated copyir.com
• If the Cutter end position switch is not pressed within 2000 ms after the Cutter motor is activated copyir.com
E16 Inking Motor Lock
• If excessive current is detected 2 copyir.com5 seconds consecutively after the Inking motor is activated copyir.com
E19 TPH pressure error [During TPH Up Positioning]
• If the light path of the TPH pressure sensor is not opened within 10 seconds after the Write pulse motor is activated copyir.com [During TPH Down Positioning]
• If the light path of the TPH pressure sensor is not blocked within 10 seconds after the Write pulse motor is activated copyir.com
E3 Clamp Motor Lock [During Clamp Motor Initial Positioning]
• If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated copyir.com [During Master Release from the Clamp Plate]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated copyir.com
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated copyir.com [When the Clamp Plate opens during Master Clamping]
• If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated copyir.com
• If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated copyir.com [When the Clamp Plate closes during Master Clamping]
• If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated copyir.com
E4 Ink Overflow
• If the Overflow sensor detects excessive ink in the Squeegee unit copyir.com
E6 Position-A Sensor Malfunction
• If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated copyir.com
J1 No Master on the Drum
• If the Master sensor does not find master on the Drum when the Drum is at 134° during the printing movement copyir.com
J10 Removed Master Jammed at the Master removal area
• If the Master removal sensor is detecting the removed master (light path blocked) even though the Drum has returned to the position-A after the master removal process copyir.com
J2 Paper Jam in the Second Paper Feed Area
• If the Paper receiving sensor does not find paper when the Drum is at Position-334° and 104° the printing operation copyir.com
J3 Paper Jam in the Paper Receiving Area
• If the status of the Paper receiving sensor does not change from detecting paper to not detecting from Drum angle 357° to 280° the printing operation copyir.com
J4 Master Loading Error
• If the Master sensor does not detect the master (light not reflected) within 5 seconds copyir.com
J5 Master Loading Error (onto the Drum)
• If the Master sensor does not detect the master (light not reflected) during the master loading when the Drum is at 134° from the position-A copyir.com
J6 Master Cut Malfunction
• If the Master positioning sensor is still detecting the master (light reflected back) when the Drum is at position-A after the cutting copyir.com
J7 Original Jam at Entrance
• During the Original scanning, if the Original IN sensor does not detecting within 5 second after the Read pulse motor activates copyir.com
J8 Original Jam
• During the Original set movement, if the Original IN sensor still detecting Original (sensor light reflected) the master making movement copyir.com
J9 Master Removal Error
• In case the Master removal sensor does not detect the removed master (light path opened) at Drum 134° from the Position -A during the master removal even though a master was detected on the Drum before the master removal operation copyir.com
اشتراک گذاری در:
در خبرنامه ما عضو شوید
تمامی حقوق این سایت متعلق به کپی ایران بوده و هر گونه بهرهبرداری از آن مستلزم کسب اجازه میباشد.